Search Documents

By M. Jaramillo

The expanded west pit of the 15 Mta (13.6 stpy) El Cerrejon mine will eventually reach a maximum depth of 270 m (890 ft). Slope-stability evaluations indicated that this depth, combined with structural complexities, would create a serious risk of footwall instability. Stabilization calls for anchoring the footwall by the installation of 9- to 33-m- (30- to 108 ft-) long multistrand steel cable bolts. For each of the 15-m- (50-ft-) high mining benches, a row of bolts is installed with variable horizontal spacing, depending on the dip magnitude. Cable bolting is now standard operating practice, and an estimated 11,800 bolts will be installed during the life of the mine. Results to date have been satisfactory in terms of the stability condition of the bolted slopes.

Jan 1, 1997

By B. K. Cantrell, K. L. Rubow

The US Bureau of Mines and the University of Minnesota have developed design and performance criteria for a personal diesel exhaust aerosol sampler for underground coal mines. These are based on the premise that size can be used to separate diesel exhaust aerosol, which is mostly submicron in size, from coal dust aerosol, which is mostly greater than a micron in size. The sampler has three stages: a respirable aerosol preclassifier, a 0.8- µm aerodynamic diameter inertial impactor to collect mineral dust and a final filter to collect the diesel aerosol. Using a sample flow rate of 2 L/min and gravimetric analysis to within 0.1 mg, the measure sub-0.8 µm diesel aerosol has an a-priori limit of detection of 0.3 mg/m3.

Jan 1, 1992

By R. Tanaskovic

The objective of study of climatic conditions in underground mines is to create a working environment suitable for normal development of operations. Disregarding the fact that the development of equipment and technology, especially during the past decade, made the work in underground mines much easier, it is observed, according to the number of professional publications, that increasing attention is devoted to the study of climatic operating conditions in mines of many countries. This indicates that the climatic operating conditions are closely connected with productivity, and in turn with mine production profitability, in addition to the protection of manpower health and working capabilities. Usually, the concept of unfavourable climatic conditions of operation implies increased mine air temperature and humidity and low air flow rate, resulting in impeded heat exhange between human organism and working environment. As known, above phenomena are present in deep underground mines where the heat problem exceeds the-problems related to other features of natural conditions of mining. On the contrary, unsuitability of climatic operating conditions in mines with shallower mining depths is manifested by inadequate heat, particularly during the cold winter period. The two stated aspects of unsuitable climatic operating conditions are not solvable only by mine ventilation, so the former case requires cooling and the later one heating of the air used to ventilate the pit, or part there of where the phenomena are manifested. Study of climatic operating conditions in mines is, due to the number of factors involved, a complex and time consuming task, and this was, among others, one of the reasons for inadequate study of these problems in many mines. However, it is evident that further development of mine production imposes the need to make the climatic operating conditions in mines similar to those existing in other activities, where increasing attention is being devoted to the improvement of these conditions. Development of mining industry in Yugoslavia, particularly over the past decades, caused several of our mines to approach mining depths where the heat regime has a major influence on climatic operating conditions. This imposed the need to determine and investigate heat regime parameters, especially those that cause unsuitable operating conditions. The results of such investigations in the case of the deep part of Lead and Zinc Mine "Trepca" - Stari Trg are briefly reported in this paper.

Jan 1, 1980

By Ajay Mahajan, Manoj Mohanty, Vishal Gupta

Modern coal processing plants utilize multiple cleaning circuits to efficiently beneficiate different size coal fractions of run-of-mine coal. An older plant optimization approach is to maintain average product quality from individual cleaning circuits at the same level as the given product specifications for the overall plant. However, many past studies indicate that the equalization of product quality approach fails to produce the maximum plant-yield. A newer approach, known as equalization of incremental product quality, requires that the incremental product quality obtained from each circuit be maintained at the same level to satisfy the overall plant product quality. This approach ensures the maximization of plant yield while satisfying a single product quality constraint. However, while dealing with multiple product quality constraints, this approach by itself may not be sufficient to obtain the desired maximum yield. For the simple reason that the dirtiest particle (or group of particles) with respect to one quality constraint may not be the same particle (or group of particles) with respect to another quality constraint, the mass yield versus product quality relationship generated by equalizing different incremental product quality may not be exactly the same. Therefore, an additional search technique has to be utilized to determine the global-maximum value of plant yield. Thus, the main objective of this study was to utilize an emerging optimization technique, known as genetic algorithms (GA) to maximize plant yield while satisfying multiple product quality constraints. The maximum plant yield obtained from this approach was nearly same as the maximum yield obtained by the incremental product quality approach while satisfying one specific product quality constraint. The GA was applied on a coal preparation plant that utilizes four circuit operations - heavy medium bath, heavy medium cyclone, spiral and froth flotation. The results showed that using GA as an optimization process gives 2.56% higher yield that will result in additional revenue generation of $5,120,000 per annum than average product quality approach.

Jan 1, 2005

By J. den Drijver, M. Opahle, R. Inderst

Safety reasons render necessary the advanced calculation of the amount of methane degassing from a longwall in the scope of the ventilation planning of mines. Today empirical methods, which are based on observations of operational procedures, are used for the calculation of the amount of methane. Despite of constant improvement those calculations are not always sufficient. In particular calculations which are based on operational facts but not proved by experience are not reliable. Most of all these calculation procedures lack physical-analytical descriptions of the procedure itself, presenting only the effects on important parameters such as the distance between seams in the roof or floor or gas pressure. Tschersich [Tschersich 961 developed an analytical model for an advanced calculation by analysing the degassing of seams in the roof and floor and the physical parameters of gasflow. This model might correct the lacks of existing procedures and improve the precision and reliability of additional calculations. The model simulates the emission record in seams of the roof and the floor. It takes into account not only a multitude of parameters such as the distance to adjacent seams and gas pressure but also the depth of seams, gas content, rank of carbonification, rock temperature, face advance rate, initial and succeeding mining and the face length. In order to comprehend and to verify those correlations we extended the model of Tschersich and programmed this enlarged model using the computer language C++. Aim of this research is to guarantee a much higher accuracy in calculating methane emission caused by mining. The improved planning is expected to result in more safety and better prevention of high methane con- tent in ventilation as well as in a better use of the capacity of the mining equipment. The application [Drijver, lnderst 961 of the ex- tended model will also be very useful in the course of research projects as it allows computer simulation, i.e. in-situ research can be extensively limited or even replaced.

Jan 1, 1997

By Edehran Lotfi, Terrence Stobbe

INTRODUCTION Mobile excavating and handling equipment are important 'tools of trade' in the mining and construction industries. The handling of this equipment must be mastered so that its limitations are learned and its harmonic use with other pieces of equipment is practiced. he sudden growth in mobile excavating and handling equipment type, size, complexity, and application started after the Second World War. This growth has not been accompanied by pertinent human factors research. Investigations into the proper and safe handling of such equipment with due regard for human and machine limitations are lacking. One such piece of equipment is the front-end loader (FEL), which during one cycle of operation excavates, loads, and hauls, (Lotfi and Adler, 1981). The diversity of action by FEL is archetypical among excavating and handling equipment. Front-end loaders are the most rapidly proliferating type of equipment in the industry. Also, front-end loaders are involved in the highest number of accidents involving mobile excavating and handling equipment. In the period 1970 to 1978, FEL's were involved in 27% of all mobile equipment accidents in surface mining (Adkins, 1980). Improving operational safety and efficiency will reduce the frequency of accidents. The performance of the operators can be evaluated and improved by the following steps: first, define the operating conditions and the operator workload intensity (Adler and Lotfi, 1983), second, monitor the operator to evaluate his task performance, and third, make recommendations based on the findings. The stressful nature of the equipment operating task is an acknowledged fact (Field, 1980). However, a systematic measurement of stress evaluation is lacking. In this paper, methods for measuring mental stress and fatigue, are defined, the mental load which caused the stress is outlined, and stress measurement methods are proposed. MENTAL STRESS Mental stress has been described as a "specific somatic response to damage or the threat of damage by several environmental agents"

Jan 1, 1986

By M. J. Virnig, J. M. W. Mackenzie, M. W. Johns

The properties of Henkel's Aurix® resin which uses a guanidine functionality to recover gold by ion exchange have been described in publications of the International Mineral Processing Congress and Randol International (1)(2). The purpose of this paper is to provide an update on the results of further testwork using Aurix®. Specifically, this paper presents the first results of resin in pulp testing, all the results previously reported were for testwork carried out using synthetic gold leach solutions.

Jan 1, 1995

By J. C. Stankus, S. Guo, S. S. Peng

In this paper, a model is developed for a resin anchor bolt system in which the smooth bar is modeled by using one-dimensional truss elements, and the resin annulus is modeled by using axisymmetric elements. These two submodels are combined and then incorporated into an existing computer code called Roofbolt. After this development, all of the components in the resin anchor bolt system, including smooth bar, bearing plate and resin annulus, can be correctly modeled.

Jan 1, 1997

By J. J. McDougall

The Windy Craggy copper-cobalt-bearing massive sulfide lies in the Tatshenshini map area of northwestern British Columbia, where British Columbia joins Alaska and the Yukon. The area is covered with numerous glaciers and ice fields that mask geologic detail and hamper ground access. In 1957, Ventures Ltd., the predecessor of Falconbridge Ltd., undertook a reconnaissance of the area using a float-equipped Supercub. At that time, large lakes and glaciers were unnamed and little was known of the geology. The prospecting team was led by J.J. McDougall with Stan Bridcut as pilot-prospector. Prospecting was directed at the St. Elias Mountains between the rich Kennecott copper deposits to the northwest and the Maid of Erin silver-copper mine on the Haines Road, BC. Reconnaissance flying in 1957 and early 1958 eliminated vast segments of the Kennecott-Haines Road terrain as being too inaccessible for mining. In 1958, the Supercub landed at an unnamed lake and the terminal moraine of an unnamed 12.9-km (8-mile) long glacier was prospected. The lake was called Tats Lake and the glacier named Tats glacier (short for Tatshenshini). Float of sulfide was found in the moraine. Follow-up investigation along Tats glacier led to the discovery of several small sulfide deposits and these were staked. Prospecting active glaciers in this area can be complicated because of drainage capture by eroding valley glaciers. Glacier capture resulted in the float from one mineralized area being deposited at different times in three widely separated moraines. Float of the Windy Craggy deposit, therefore, occurs along the course of older glaciers and at the base of the currently active ones. The problem of sourcing caused much additional Supercub reconnaissance. It is interesting to note that about 40 geographic names were given various features in this unmapped portion of the St. Elias Range, and these names were ultimately officially adopted.

Jan 1, 1991

By William A. Kneller

Fifteen samples of chert from seven localities in Ohio were tested for potential durability and reactivity in concrete. The tests determined are porosity, pore-size distribution, relative degree crystallinity, specific surface area, and degree of dissolution according to the ASTM C289-71, Potential Reactivity of Aggregates, Chemical Methods. The results of these tests were compared with petrographic, electron optical, physical-chemical, and engineering properties of the chert samples. Based on these tests, the important properties that affect the durability and reactivity of chert in concrete were observed to be: (1) porosity, (2) pore-size distribution or pore spectra, (3) relative degree of crystallinity, (4) grain size, (5) specific surface area, (6) impurities, and (7) amount and species of quartz present-all of which are functions of original composition, time (geologic age), depth of burial, tectonics, and diagenesis. Preliminary results of this study indicated that the geologic history and physical-chemical properties of chert vary from one sample to another, and any one or combination of these parameters affect the performance of the chert in concrete. These complex interrelationships are difficult to ascertain; if the performance of the chert in concrete is to be predicted, it is necessary to study in detail this enigmatic material.

Jan 1, 1978

By John D. Batty

With the emergence ofbiooxidation as a viable process for the pre treatment of refractory gold ores, so have the number of publica­tions on this topic increased dramatically. To a novice in the field of biooxidation, the infonnation presented is often confusing and sometimes even incorrect. Infonnation has also been published that is misleading in that it highlights a particular feature of a process that is either totally irrelevant or of no consequence to the ultimate goal viz. achieving the maximum economical gold recovery. To assist a potential user of biooxidation in evaluating the available published infonnation some guidelines or considera­tions for some of the more important aspects are given, as well as some extracts from publications that demonstrate the manner in which information has been presented.

Jan 1, 1996

By Roshan B. Bhappu

The extraction of gemstones, except for diamonds, continues to be a more or less handpicking type operation all over the world. However, considering the physical properties of gemstones such as density (sp.gr.), color, size, shape, luster, brilliance, reflection of light and the like in contrast to the relatively ‘dull’ physical characterization of the associated gangue minerals, it should be feasible to recover several gemstones using modern mineral processing techniques. This paper illustrates the unique physical characterization of several gemstones and suggests appropriate mineral processing techniques that could be used to recover these precious stones. Special emphasis is placed on the versatility of the Heavy Media Separation (HMS) process for processing of the gemstones. Finally, a few examples of commercially viable operations involved in the recovery of emeralds and rubies are presented.

Jan 1, 2005

By P. J. Hyde

Cyanide is a significant contributor to the cost of producing gold. Any reduction in consumption that can be achieved through more reliable measurement and/or more efficient management of dosing rates can have a significant financial impact. An automated analyser, by its mechanical nature, is not prone to the variations of human operators, particularly notice­able from shift to shift. Reducing the standard deviation of the measurement (ie, reducing noise ), the automated measurement will give the metallurgist a truer picture of the underlying patterns of usage. The combination of automated analysis with on-line operation and a control loop provides timely information that is efficiently utilised in the management of the plant. Until the release of the Chemtronics On-Line Cyanide Analyser (OTA3000) about 12 months ago, the Australian experience with automated analysers (especially on-line) had been substantially negative. Since its release, the Chemtronics instrument has outperformed both manual titrations and other automated instruments, gaining an enviable reputation for accuracy and reliability in the process. The instrument is built around the technique ofpotentiomet­ric titrations, in which the potential of an indicator electrode is measured as a function of the volume oftitrant that is added to the sample. As the cyanide in the sample is depleted, the potential on the indicator electrode changes rapidly, producing a typical sigmoidal curve. The OTA3000 takes the first differ­ential of the curve, identifies the apex of the peak as the endpoint and reports the result in parts per million of sodium cyanide. The OTA3000 accepts the peak as valid only if it exceeds a certain minimum height. That minimum height is a programma­ble parameter and is used to optimise the relationship between sensitivity and the rejection of spurious peaks. The instrument will track cyanide trends through both positive and negative slopes of any magnitude, but it will provide a warning if it the slope becomes excessive, not because it affects the instrument but because it means that something unusual is occurring in the tanks. There are a limited number of conditions under which the instrument will produce a result of zero. In these cases the OTA3000 holds any output lines at the last valid result while it repeats the titration. This feature was incorporated for reasons of stability in a feedback loop.

Jan 1, 1995

By Raja V. Ramani

The importance of adequate mine ventilation for good health and safety conditions has been recognized since miners first ventured underground. All over the world, governmental actions on mine health and safety are directly connected with mine atmospheric environments, their assessment and control. These governmental actions have been, and continue to be, motivated by the repeated experience that potential threats from inadequate control can evolve, either suddenly or in the long-term, into unpleasant reality, with catastrophic health and safety consequences. These governmental actions are also an indication of the remarkable professional progress being made in the field of mine ventilation. Surely, no developed country allows underground mines to operate without strong measures for the control of ventilation under legislation specific to the mining industry. In the United States, the federal government's responsibility for mine safety has evolved over the years through a series of legislative actions beginning in 1865 and continuing through 1910, 1941, 1947 and 1952. The passage of the Federal Metal and Nonmetallic Mine Safety Act of 1966 (the 1966 Metal Act), the Federal Coal Mine Health and Safety Act of 1969 (the 1969 Coal Act) and the Federal Mine Safety and Health Amendments Act of 1977 (the 1977 Mine Act) are the most important milestones in this long legislative history. The 1977 Mine Act adopted many of the stronger features of the Occupational Health and Safety Act of 1970, perhaps the most significant piece of legislation on workers' occupational health and safety in US history. It is worthwhile to ask, "How far has the United States come in mine ventilation since the enactment of the 1969 Coal Mine Health and Safety Act?" This Act and its associated regulations defined in great specificity many standards for healthful and safe operation of a mine and, in some cases, what constitutes good ventilation practice. Since 1969, the frequency and severity of disaster-type events in US coal mines has decreased markedly. A primary reason for this achievement is the strength of the Coal Mine Health and Safety Act's regulatory features in such areas as methane concentration control, dust control, intrinsic safety and explosion-proof enclosures, minimum air quantity and quality standards and air distribution and escapeway provisions. These requirements greatly influenced mine ventilation planning, engineering and practice, leading to increasingly safe working conditions.

Jan 1, 1993

By Pierre Mousset-Jones

I wish to submit this discussion item on an article published in the August issue of MINING ENGINEERING by Wala and Altman on the use of canonical diagrams for mine ventilation networks. The advent of computer graphics and plotting has enabled complex underground mine layouts to be displayed and plotted in a variety of three-dimensional formats that very closely represent the actual mine layout. This enables the ventilation engineer, who is familiar with the mine, to display the network pressures, quantities, resistances, and fan locations in a way that can be understood by everyone working at the mine. This is important if the ventilation engineer needs to discuss changes in ventilation with production personnel, or escapeway procedures with union personnel. While I can see some of the potential advantages in the canonical ventilation network diagram described by Dr. Wala, it appears to me that the fact that the diagram has no visual equivalence with the actual mine layout means that most mine personnel will find such a diagram almost incomprehensible. The authors have alluded to certain advantages with the canonical diagram. However, I find it difficult to see that these outweigh the fact that almost everything listed can be duplicated in isometric diagrams, and in a manner that is easily understandable to everyone in the mine from the miner to the mine manager. Perhaps the authors could show a clear example comparing an isometric with a canonical portrayal of a mine network showing the information that is immediately available from the canonical network that is not obvious in the isometric diagram. There is in this country a severe problem with the need for ventilation engineering and expertise to be used and accepted by mine management as a necessary part of mine planning. It seems to me that to introduce the requirement for further explanation so that management can understand a canonical network display will hinder more than help the recognition that ventilation engineering needs at so many mines in this country. However, I can see that the canonical approach does have its place in assisting the practicing mine ventilation engineer, wherever he or she exists in the organization chart for a typical mine. In this case, could the authors please indicate the availability of the computer program to compute and plot the canonical diagram for a mine ventilation network.

Jan 1, 1989

By C. Tsamantaki

Water-bentonite suspensions exhibit a yield stress which is defined as the minimum applied stress for flow. Considerable debate exists about the yield stress being a material property, hence different measuring methods should give similar answers, but several investigators have demonstrated that it is an engineering reality. Yield stress is normally estimated indirectly from the rheogram obtained with a viscometer following an extrapolation to zero shear rate (the dynamic yield stress), but the technique may be prone to errors because of slip flow. Direct measurements, not prone to such errors, rely on an independent assessment of the yield stress, normally carried out with the vane method (the static yield stress). In this paper results are presented and compared regarding the yield stress of 14 different water-bentonite suspensions measured using both the direct and the indirect methods. In order to obtain a wide range of yield stress values, two different types and two concentrations of bentonite at various pH were tested. Rheological data were obtained using a rotational speed viscometer and a yield stress vane measuring device. Measured vane yield stress values ranged from 5 Pa to 83 Pa. Rheological data collected with the rotating viscometer were fitted using various conventional techniques (interpolation, linear and non-linear regression analysis) as well as using a golden section yield stress search methodology based on Herschel-Bulkley model, developed in house. The vane instrument measures directly the yield stress of the suspensions and requires no further data handling. A comparison of the measured values of the yield stress with the direct and the indirect method is then made for the water-bentonite samples. Not very large differences are observed among different techniques and the variations are discussed. Similar data from literature are also analyzed and the comparison shows that differences on the various estimation methods are much larger than the differences observed in this study.

Jan 1, 2006

By Armine F. Banfield

Selection of a plant site is becoming increasingly more difficult and important, mainly due to advances in technology, antipollution laws and changing economic, social and community conditions. Discussion falls naturally under three headings: economic considerations, terrain considerations and environmental considerations. Aside from acquisition of surface rights, problems having to do with terrain, or topography, usually can be dealt with by management alone. Economic considerations largely involve decision-making by management plus negotiations with government regulatory agencies acting under set rules. Environmental considerations, such as air and water pollution, townsites, housing, schools, noise abatement, appearance, surface rehabilitation and the like usually are under the control of federal, state or municipal bodies with a large degree of decision-making. Successful solution of environmental problems often requires lengthy negotiations, during which public relations by the mining company play an important part. Existing union regulations or customs may confine decision- making and the establishment of wage rates, working conditions and regulations. These usually require considerable planning and negotiation. Initial production often is delayed by formal negotiations involving environmental considerations. Surface facilities usually can be divided into two broad categories: those for concentrating ores--such as gold, silver, base metals, low-grade iron ore and potash-which should be close to the mine to reduce ore-transportation costs to a minimum, and those where the ore is shipped elsewhere for treatment, such as direct-shipping iron ores, complex high-value ores requiring specialized treatment and ores from which special products are derived for local markets. The long-term aspects of plant-site selection too often are given no or insufficient consideration because of immediate financial limitations. As a result, additional capital expenditures may be required later for relocation of townsites, roads, railroads and plants to provide additional room for extension of open-pit operations, tailings disposal, storage, or danger to foundations through underground subsidence or open-pit mining. In the past, hillside sites for concentrating plants were preferred to take advantage of gravity-feed methods The modern trend, however, is to place as much equipment as possible on approximately the same level. Some costs relating to plant sites are included in this section. They are ranges as of the year 1970, and are offered only as general guides. Such costs will vary widely with geographical location and, of course, are subject to escalation due to increases in wage rates and cost of materials. Items in the bibliography contain more detailed and comprehensive data on specific subjects. Most contain bibliographies of their own.

Jan 1, 1973

By John W. Rozelle, David S. Bolin

INTRODUCTION During the normal course of a mining project, a feasibility study will be prepared that addresses all the aspects of the project including geology and mineral inventories, mining and geo- technical, metallurgical processing, infrastructure, environmental considerations and economic analyses. These studies are prepared for various reasons. Occasionally, a feasibility study will be prepared solely for use within a company as justification for development expenditures, however, these documents are frequently submitted outside the company either to raise funds from financial institutions or from public financing on one of the various securities exchanges. Mineral industry consultants are often called upon to participate in the preparation of feasibility studies or to conduct an independent audit and review of an internally prepared study. As the recoverable mineral resources form the foundation upon which the balance of a feasibility study is based, including the economic analysis of the project, the resource aspect of the study is examined very carefully by financial and securities organizations. The balance of this discussion is directed toward the various geological and resource estimation aspects of feasibility studies that experience has shown to be of particular importance. Much of this discussion will be directed toward open pit gold operations, although the principles are applicable to any type of deposit. 2.0 GEOLOGIC RESPONSIBILITIES IN FEASIBILITY STUDIES The principal geological effort in the preparation of a feasibility study is generally dedicated to the following areas: - Preparation of Geologic Reserve/Resource Estimates - Condemnation of Sites for Facilities, Access Roads, Leach Pads, Waste Dumps and Tailings Disposal - Collection of Geotechnical Data - Provision of Mineralogical and Petrological Data Pertinent to Metallurgical Processing - Selection of Appropriate Bulk Sampling Sites for Collection of Metallurgical Samples Each of these items will be addressed in detail in the following sections. 3.0 RESERVE/RESOURCE ESTIMATION An ore reserve estimate consists of the determination of a volume, or tonnage, and a grade for the deposit. There are numerous cases in the mining industry of projects that have experienced severe difficulties when operational ore grade, tonnage or metallurgical amenability have proven to be deficient compared to predicted estimates. An error in estimation of tonnage generally leads to more long term problems affecting mine life and production schedules. However, a significant error in the estimation of grade, particularly if mined grade is lower than anticipated, can have an immediate, and often disastrous, effect upon a project. The geologic preparation leading to an ore reserve estimate generally follows a logical sequence familiar to

Jan 1, 1987

By S. R. Wardwell, M. J. Robison

INTRODUCTION The first phase of the Los Angeles Metro Rail Project consists of 7.1 km of subway and stations running through downtown Los Angeles from Union Station to MacArthur Park. Contract A146, Tunnels from 5th/HILL Station to 7th/Flower Station, involves tunnel construction through the heart of downtown Los Angeles. The alignment of the tunnels passes beneath twelve buildings, ranging from a 3-story below grade parking structure to numerous 12 to 14 story buildings. The soil along the alignment is alluvium, consisting of silts and clays, clean sands and gravels located above the ground water table. Because of unstable ground conditions, which led to excessive ground losses in several instances, and because of the potential for excessive building settlements, it became necessary to design and perform a program of chemical grouting. The chemical grouting program was designed such that tunneling could proceed on a one shift per day basis, with chemical grounting being performed on the remaining two shifts. Each day 21,000 to 31,000 liters of sodium silicate grout were injected through sleeveport grout pipes installed 18 m deep through the tunnel face. Tunnel advance rates of 12 m per day, 60 m per week, under full chemical grout cover were achieved. The chemical grouting program virtually eliminated both ground loss and settlement and permitted successful excavation of the tunnels. The purpose of this paper is to describe the chemical grouting program used to control ground losses and settlement on Los Angeles Metro Rail Contract A146. The paper begins with a description of

Jan 1, 1991

By F. A. Gates, Bengt Samuelson, James E. Edmunds, S. McCune, Neil Hario, Norman L. Weiss, J. M. Bertram, A. M. Cavaliere, F. M. Jr. Stephens, D. D. Chiang

DESIGN BASIS Size of Project The size of the project generally is expressed in tons of ore milled per day, but company policies differ widely in this respect with a few adhering to this set figure but many expecting the design capacity to be liberal. To some companies that follow the latter practice a 25,000-tpd milling plant that cannot reach 30,000 or 35,000 tpd with¬out major additions is a disappointment. The engineers responsible for planning the operation must know what is intended. Other projects are sized according to the tonnage of product rather than of mine ore; examples are iron ore mills that express size in terms of tons per year of pellets or high-grade concentrates, heavy minerals plants in tons per year of rutile or ilmenite, cement plants in barrels per year, potash in tons per year of muriate, phosphate in tons per year of washer rock and flotation concentrate, and others. However, tons per day milling rate is also the common denominator in most of those instances because the major equipment has to be selected on that criterion. Equally important are operating schedules, particularly the number of operating days per week and shifts per day for ore delivery, crushing, grinding, and processing. Hours per shift also are an impor¬tant factor in design, particularly in the case of ore delivery, and the lost time expected for maintenance, cleanup, inspection, preventive maintenance shutdowns, and many others, has to be taken into ac¬count. Frequently, the ore deposit will vary in hardness and grade to such a degree that the capacity of the mill will vary widely from year to year and cannot be expressed as a fixed figure, but rather as an average over a calculable period, such as ten years, or as a specific daily capacity over the first two years, next four years, etc., or some similar projection. A good example of this kind of situation is Asarco's Mission operation 15 miles southwest of Tucson, Ariz., described by Weiss and Vincent,1 where the major rock types differed widely in hardness, so that a change in the proportion of these types in the mill feed could have imposed difficult design problems if a constant tonnage rate had been expected. Expected Life The life of a mining operation depends upon the size of the deposit and the rate of mining. The latter is a policy decision based on an economic analysis2 which, in turn, is based on many factors. From the point of view of mill planning, the estimated life of the operation determines many criteria and affects many decisions on strength of structures and degree of protection of men and materials, the quality of the materials-handling and process machinery, the type of delivery systems for ore to the mill and concentrates to the smelter or market, environmental considerations, and many others. Costly installations that may be excellent investments for a 20-year project may be waste¬ful for a 5-year operation. An example is the comparison of different methods of crushing or grinding. Take single- vs. multiple-stage grind¬ing-the former may be found more economical for a 5-year operation, and the other, more costly method more economical for a 15- to 20-year life. Mining and Ore Transportation The mining method and the means of transportation of the ore to the first crushing stage have far-reaching effects upon mill design, particularly the crushing sections, and upon site selection (see Chapter 2, Situation of Mill). Consequently, mill design cannot advance until the mine planning has reached at least tentative decisions concerning these important matters, or reach the final stages until much is known about the ore that may be expected month by month and year by year for a reasonable period. Methods of ore transportation used in over 90 underground and open-pit mines are listed briefly in Section 32 (Table 1), and more detail is found later in this section and in Section 10, Storage and Transport. These methods include surface railroad, trucks, conveyors, surface skips, underground skips, and tramming from hoist or tunnel. In surface mining, transportation of the uncrushed ore by rail or truck to the primary crushing plant-conveniently located for lowest overall cost-is most common. Rail transportation provides low perton-mile costs. Truck transportation, though in some cases less eco¬nomical, is more flexible and more adaptable to mountainous terrain; furthermore, recent improvements have reduced the operating costs to keep trucks competitive on low-grade ores. The design of the primary crushing plant will be essentially the same whether delivery is by truck or rail, but the location of the plant is subject to more rigid restrictions in the latter case because of grade limitations, and these in turn may adversely affect the selec¬tion of the mill site as well. The influence of truck haulage in reducing the stripping ratio in open-pit mines is an added reason for predicting a minor role for rail transportation in the future. The use of conveyors to transport ore from the pit to the milling plant involves (in most cases) crushing the ore to a reasonable size (10 to 20 in. maximum with today's crushers) before conveying. The Twin Buttes system3 which went into operation in late 1969, utilizes primary crushers (two) and conveyors to receive rock waste, ore, and low-grade stockpile material from trucks, then transport them to the appropriate destination. Flexibility is dependent upon the porta¬bility of the primary crushers. In the face of this development, inclined skip hoists are no longer important to the mill designers. Underground mines generally pose fewer problems of design; these will be discussed in Chapter 2. Character of Deposit The degree of homogeneity of the ore in various parts of the mine is an important factor. The characteristics that concern the millman (approximately in order of importance) are: hardness, assay, metallurgical response, size distribution,4 and moisture content. Under metallurgical response may be included degree of oxidation, mineral¬ogy, clay content, and reagent consumption, as well as process re¬sponse in general. Short-term variations-hour-to-hour, day-to-day, or even week-to-week-make operation of the plant more difficult, require greater flexibility of process design and, perhaps, also require more instrumentation and manpower. Uniformity of the ore in the characteristics noted previously and

Jan 1, 1985