Search Documents

By Y. Astafyev

Autotransport is one of the most conventional kinds of transport in iron ore open-pits. It. is successfully used both independently and in combination with other kinds of transport. In the Krtvoy Rog Basin open-pits annual truck transportation accounts for more than 235 million tons of ore and waste rock. In the process of operation trucks make up various transport streams depending on - the development of autoroads in the open-pits; - the capacity and the number of loading equipment ; - the load carrying capacity and the speed characteristics of trucks

Jan 1, 1979

By James E. Monsees

Extensive underground excavation will be required for construction of a mined geologic repository for nuclear waste. Hundreds of thousands of feet of drift will be required based on the conceptual layout design for each candidate nuclear waste repository. Comparison of boring and blasting excavation methods are discussed, as are special design and construction requirements (e.g., quality assurance procedures and performance assessment) for the nuclear waste repository. Comparisons are made between boring and blasting construction methods for the repository designs proposed for salt, volcanic tuff, and basalt. Differences in the geologic media and settings of the prospective sites influence the excavation method in terms of drift length, size of opening, drift slope, rock quality, and boreability. Support requirements, ventilation, and the ability of the geologic system to retard radionuclide migration are also directly impacted by the geology and excavation method.

Jan 1, 1987

23.1-SOURCE, POWER-SYSTEM ELEMENTS A. J. T HUM Basic considerations in providing power for mine production and collateral operations are: 1. Mining operations of any size normally use electric motors for driving all equipment except mobile service units. 2. The electricity for power may be purchased or self-generated, depending on the location, size and specific operating circumstances of the individual property. 3. The major elements of the power system will be the source, either an incoming transmission line from a utility in the case of purchased power or the power plant if self-generated. Energy for the power plant may be water, hydrocarbon fuels, waste heat or nuclear, which will govern the type of prime mover selected. 4. The electricity normally is generated in the form of alternating current and must be distributed to the points of usage. This usually requires a primary substation for transformation to suitable voltages and secondary substations at points of usage throughout the operations, The power is delivered from the primary to the secondary substations over transmission lines or cables, depending on distances, voltages and local conditions. 5. At the points of use, there will be starting and protective devices for each motor. In some instances, direct current will be needed and rectifiers of various types can be used to provide it. 6. The entire electrical system requires suitable switching and protective devices to prevent damage to the equipment in case of power failues or faults; also, in most cases, sufficient metering to establish the demand and amount of electrical energy consumed. 23.2-PURCHASED POWER A. J. THULI 1. Where public-utility or government-generated power is available, it usually is advantageous for the mine owner to purchase rather than generate. Purchased power generally will be cheaper and more reliable than operating a small generating plant except in some cases where waste heat is available as the source of energy and can be used to supply all or a portion of the power requirements. 2. If it is decided to purchase power, the owner usually must participate in the cost of constructing the connecting line from the closest existing utility line to his point of usage. If the connected load is less than 1,000 lip, it probably is best to let the utility provide the primary substation. For larger connected loads the owner can obtain a more favorable "primary voltage" rate if he provides the primary substation to receive the incoming power and transform it to the distributing and usage voltages. 3. The cost of purchased power usually is made up of a demand charge, deter¬mined by the maximum amount of power the customer takes during any 15-min period throughout a month, and a graduated energy charge for the kilowatt-hours consumed-that is, so much for the first block of energy based on the demand,

Jan 1, 1973

By Dale R. Ralston, Roy E. Williams, Gerry V. Winter, George L. Bloomsburg

GENERAL STATEMENT Data frequently can be collected by several dif¬ferent methods. The method required for the nec¬essary precision for inflow prediction to mines should be selected and other methods avoided. Pre¬cision monitoring or measuring techniques fre¬quently require more time, expertise, and expense in their implementation that may not be justifiable. The temporal distribution of the data needs also may dictate the method used for data collection. Continuous recording devices may be required for time sensitive data whereas point measurements of other parameters may be adequate. Data needs will vary as the hydrologic investigation proceeds. In¬itial data needs may require only a qualitative col¬lection of data such as the areal distribution of precipitation. Subsequent data needs may require the measurement of ground water levels to the near¬est hundredth of a foot. Data requirements can be difficult to fulfill for ground water systems. This is particularly true for anisotropic, heterogeneous hydrostratigraphic units since the hydrogeologic parameters vary both ver¬tically and areally. Techniques exist for determining the storage characteristics of both unconfined and confined hydrostratigraphic units but these pro¬cedures require the installation of multiple wells in the same unit which may be impractical. Specific tests are discussed subsequently that permit the determination of vertical hydraulic conductivity. Data collected from field procedures or tests are generally preferred to laboratory derived data. This is especially true for hydrogeologic parameters such as hydraulic conductivity. SURFACE WATER SYSTEMS Precipitation Precipitation data can be collected from sources that maintain a historical record. The US Depart¬ment of Commerce, National Oceanic and Atmos¬pheric Administration (NOAA), maintains weather observation stations across the country. Such a sta¬tion frequently can be found near a proposed mine site but the type of weather data collected varies from station to station. Fortunately, precipitation data are collected ubiquitously. The data collected by NOAA can be purchased for the area of interest in the form of monthly and annual tabulations. Private weather stations constitute a second source of precipitation data. Existing data usually are analyzed by one of three methods. The station average method merely sums the depth of precipitation at each station and divides the sum by the number of stations as fol¬lows: [ ] where Pavg is the average precipitation (L), P, is the depth of precipitation at station i (L), and N is the total number of stations. This method is applicable where there are a relatively large number of stations uniformly distributed across the area (Hjelnfelt and Cassidy, 1975, pp. 71-72). The second method, called the Thiessen poly¬gon method, weights the precipitation at each sta¬tion in direct proportion to the area it represents without consideration of topography. The stations are plotted on a map and perpendicular bisectors are drawn on the lines connecting the stations. The polygons formed by these bisectors constitute the area that the precipitation for that station repre¬sents. The overall precipitation can be calculated with the following equation:

Jan 1, 1986

By William S. Brack

The mining industry is very capital intensive. Competition for shareholder investment has never been greater. Among our challenges is the need to meet shareholder expectations (return on investment), and one area of focus lies in our ability to deliver value on our capital investments. Our ability to meet project expectations affects not only the economics associated with the immediate project but also directly influences our ability to finance future projects. Moreover, our ability as individual companies to attract investor capital is influenced by how we have done overall as an industry, and our industry track record has not been that stellar. With safety, scope, cost, schedule, and quality as guiding principles, our project managers today must address high expectations on every project. This paper examines some items that should be on today's project management checklist. PROJECT ENGINEERING Herbert Hoover, himself a mining engineer, said Engineering is a great profession. There is the fascination of watching a figment of the imagination emerge through the aid of science to a plan on paper. Then it moves to realization in stone or metal or energy. Then it brings jobs and homes to men. Then it elevates the standards of living and adds to the comforts of life. That is the engineer's high privilege.

Jan 1, 2004

By Terry Quinlan

The financial evaluation of an orebody uses estimates for the grade of ore produced during each year for the life of the mine. Assay data from the Dolphin Scheelite Mine is used to estimate grades by the Polygonal, Ellipsoidal and Disjunctive Kriging Methods. The results are compared with simulated production data, to show the existence of a bias associated with each method. The affect of bias on the financial evaluation of a theoretical model ia assessed.

Jan 1, 1979

By G. Zandt, H. R. Pratt, W. A. Hustrulid, M. Bouchon, D. E. Stephenson

PREFACE The National Waste Terminal Storage Program was initiated to conduct the research to select a site for the disposal of high level radioactive waste in deep geologic formations. As part of this program, the Savannah River Laboratory at Aiken, South Carolina, is conducting geologic research of generic applicability on the potential subsurface damage to a repository from an earthquake. Part of this study involved the collection of data on subsurface damage due to an earthquake, and another part involved the calculation of displacement fields as a result of an earthquake. Both of these studies were conducted at Terra Tek of Salt Lake City. This report is an abridged and combined version of both studies which was presented at the Rapid Excavation and Tunneling Conference in Atlanta, GA, on June 19, 1979.

Jan 1, 1979

By J. Pang, S. Chander

The mechanisms of chalcopyrite oxidation in alkaline solutions have been studied using cyclic voltammetry and impedance spectroscopy techniques. The cyclic voltammetry was used to elucidate oxidation/reduction reactions, whereas impedance spectroscopy was used for in-situ characterization of the interface. To analyze the impedance spectra, equivalent circuit models were constructed based on a layer- wise growth of reaction products. Parameters of the equivalent circuit were calculated by comparing the experimental spectrum with that expected on the basis of equivalent circuit. From the value of equivalent circuit parameters, properties of the surface layers were inferred. These properties change substantially with the change in oxygen and/or collector concentration in solution. From such changes the effect of oxygen and collector concentration on the contact angle and flotation behavior of chalcopyrite were interpreted.

Jan 1, 1991

By Deli Hu, Xiangze Shu, Cai Wang, Hongfu Liu

To detect the place and range of fire is one of the key technologies in the extinction of coal mine underground fire. A fire-prevention and extinction research team of Shanxi Mining College have successfully carried out a program detecting the place of fire with radon. In the past four years the authers have done the detecting work in several mines in Shanxi Province, such as Gujao, Xuangang Louan and Ningwu. The place and scope and the trend of underground fire of coal mine can be now exactly estimated. The data and information from detecting provide a reliable basis for drawing up the scheme to extinguish underground fire and extract mineral coal securely. The principle and method of fire detecting based on radon on surface, the data processing and analysis are discussed in this paper.

Jan 1, 1991

By Ellis G. Goree, George A. Simmons, Andrew B. Pervis

The pneumatic classifiers are widely used for fine dry powders separation These classifiers can be used for either the removal of fines from coarse feeds or the removal of coarse particles from ultrafine feed To optimize the operation of pneumatic classifiers, a thorough understanding of the impact of operational parameters on the efficiency of classification is essential This paper describes the design features and effects of operational parameters followed by illustrations of pneumatic classifiers usage in two case studies

Jan 1, 1983

By J. Y. Hwang, M. L. Jeong, R. C. Greenlund

Various aluminum-smelting by-products from three production sources were received and characterized. The waste materials were tested for compound identification and environmental acceptance. A coarse metallic aluminum recovery test using an Eddy Current separator (ECS) was performed using two different Circuit configurations. White dross performed equally well with either Circuit, while black dross processing shows significant difference on the separation results. It was found that ECS technology was effective for particle sizes down to 6-10 mesh.

Jan 1, 2001

By Carl R. Peterson, John Herrick

INTRODUCTION The need for substantial advances in underground excavation technology has produced considerable research activity on a wide variety of concepts under a variety of Government funded programs. One goal of this "Rapid Excavation" effort has been the development of a means to apply the well-known virtues, both technical and economic, of the drill and blast method in a continuous process. The spiral blast concept, aimed at this specific goal, has been funded for initial studies (1) by the ARPA Rapid Excavation Program and, for the experimental work reported herein, by the Department of Transportation (2). The economy enjoyed by the drill and blast method stems from two factors: explosive energy is relatively cheap; and this energy is released so as to cause rock fragmentation largely through tensile failures. The relative ease and efficiency of tensile rock failures have long been recognized. The drill and blast process of course cannot be truly continuous since drilling and blasting (and other necessary functions) simply are separate, distinct operations. Although some surface explosive work has been done to avoid the need for drilled blast holes (3) it does appear that the high performance associated with explosive excavation requires placement of the explosive beneath the rock surface. This paper describes studies of blasting pattern which, in simplest terms, replaces the occasional heavy blast of conventional practice with frequent, much smaller blasts. The objective, of course, is to reduce the size of individual blasts

Jan 1, 1974

By W. M. Ma, Daniel W. H. Su, K. Centofanti, Yi Luo, W. L. Zhong, Syd S. Peng

7.1 INTRODUCTION Subsidence measurements include surveys of surface and sub- surface movements and measurements and monitoring of surface structural damages. In this chapter the most commonly employed methods are discussed. 7.2 MEASUREMENT OF SURFACE MOVEMENT Surface movements involve two basic components, subsidence and displacement. The other five components (i.e., slope, curvature, strain, twisting, and shearing) are derived from the two basic components. Since all measurements are geometrical, they can be measured by common surveying techniques. 7.2.1 MONUMENTS The first step is to select the types of monuments or surveying stations. Various types of monuments have been employed. The simplest one is a paint mark on the pavement or concrete slab, although this should be discouraged because it is easily affected by artificial or environmental factors. Others use steel or wooden rods, 2 to 3 in. in diameter or square by 2 to 5 ft long, driven all the way down, flush with the ground. Both types of-monuments have no provision for frozen ground heave and both are tampered with easily. A more elaborate type is shown in Fig. 7.1 (O'Rourke et al., 1982). A rebar or iron pipe, 2 in. in diameter by 6 ft long is driven down to nearly flush with ground surface. The top 4-ft section of the hole around the pipe is enlarged to 1 ft in diameter and grouted with concrete. The most sophisticated type of monument is shown in Fig. 7.2 (Conroy and Gyannaty, 1983a). It consists of two hollow steel pipes. The inner I-in. pipe, 10 ft. long is enclosed by a 2-in. pipe at the upper 5-ft. interval. The gap between pipes is filled with foam to isolate the inner pipe from external environmental effects. The bottom of the inner pipe can either remain open or be sealed with a cap, depending on whether the ground is dry or wet. 7.2.2 MONUMENT ARRANGEMENT AND SURVEY LINES The monuments are installed strategically to form survey lines. Three basic types of monument arrangements are shown in Fig. 7.3. Figs. 7.3a and 7.3b are for single and multiple panels respectively; Fig. 7.3~ is mainly for research purposes with multiple survey lines both in longitudinal and transverse directions. This is extremely useful for defining the distributions of ground deformation, as shown in Figs. 2.10 and 2.11. Basically there are two types of survey lines: the whole basin survey line which extends across the panel width or length (e.g., lines R, R, in Fig. 7.3 a&b), and the half basin survey line which covers approximately half of the panel width or length (e.g., lines R, F in Fig. 7.3 &b). Survey lines are generally straight and linear. They should be located on the major crosssections of the subsidence basin. Survey lines must extend beyond the edge of the opening for a sufficient distance so that the edges of the subsidence basin can be determined accurately. The minimum distance from the edge of the opening must be [ ] where h = mining depth, [ ] = angle of draw, and [ ] = 5 to 7 times monument spacing for whole basin surveys, or 8 to 10 times the monument spacing for half basin surveys. There must be at least two controlling monuments at each end of each survey line. Controlling monuments must be located beyond the influence of underground mining. The spacing of the monuments ranges from 15 to 200 ft. The UK National Coal Board (NCB, 1975) recommended a spacing equivalent to 0.20 of the mining depth. Peng and Geng (1982) recommended that the maximum monument spacing be dependent on mining depths as follows:

Jan 1, 1992

By H. Burger

For mine planning in the hardcoal industry the reliable prediciton of the properties of a deposit-both ahead of the zone to be worked as well as of zones at depths not yet developed - may help improve the production results of workings. With the wide spacing of exploration drillings usual in the coal industry, it is hardly possible to establish adequately reliable plans just by simple kriging methods. During the exploration phase a decision has to be made whether the zone ahead of a face area is economically profitable and, in addition, accessible and safe in order to be included in the production planning. It is, first of all, important to gather global information on certain parts of the planning area it the form of local estimates. Moreover, cut-off problems play a critical role, e.g. if there are set cut-off thicknesses as a criterion for minability or if safety aspects have to be considered. Conditional simulation appears to be a useful geostatistic method in order to localize or predict areas of potential rock burst hazard - based on geological criteria in conjunction with the guidelines by mining authorities - in the zones ahead of a working. It is a means of providing an objective basis for the evaluation and planning of mining activities.

Jan 1, 1986

By M. K. Gangal, E. D. Dainty

CANMET/MRL has been contributing to an industry/government program to assess the quality of air in mines, and improve the working environment for Canadian miners. The ultimate aim of this program is to recommend a sampling methodology and appropriate concentration limits for both the soot (diesel particulate matter - DPM) generated by diesel equipment, and respirable combustible dust (RCD) as measured underground. The program was conceived by the Canadian Adhoc Diesel Committee, which consists of representatives from seven major Canadian mining companies, three provincial inspectorates, one union representative, two manufacturers of diesel equipment, and CANMET, a Federal Canadian research agency. This paper describes the modification and laboratory confirmation of an existing methodology for the sampling and analysis of DPM/RCD, including: sampling problems, filter selection, filter efficiency, DPM size distribution, the approximate performance of fractionating devices, and it reports the results of current ambient measurements of exposure levels in Canadian underground mines. Because of the concern about the health impact of DPM/RCD on mine workers, North American agencies are in the process of establishing limits for these aerosols. So far, the Province of British Columbia is the only jurisdiction in North America to legislate the maximum exposure level of RCD in its underground mines, i.e. 1.5 mg/m3 interim level recommended by the Adhoc Diesel Committee. It has also recommended the use of the CANMET/ADHOC RCD sampling protocol.

Jan 1, 1993

By Raymond E. Krauss

The McLaughlin Mine is based on a world class epithermal gold deposit located in the coastal thrust fault of northern California, about 1 12 air km (70 air miles) north of San Francisco. Owned and operated by Homestake Mining Co., the McLaughlin deposit contains about 18 Mt (20 million st) of gold ore at an average grade of 5.2 g/t (0.152 oz per st), or about 93 t (3 million oz). The area was identified as a gold target by Homestake in early 1978. Drilling confirmed it to be a commercial deposit by 1980. The mine was then planned, engineered, built and brought into production by March of 1985. The deposit was historically a part of the Knoxville District. It was mined for cinnabar, which was used to produce mercury for use in recovering gold and silver in the Mother Lode and Comstock districts. At that time, the mine was called the Manhatten and later the One Shot Mine. It was worked for more than 100 years, producing about 76,000 flasks of mercury without any awareness of the presence of economic concentrations of gold. By 1978, the site was largely disturbed and entirely unreclaimed.

Jan 1, 1990

Dunn has written an excellent paper providing a wealth of advice on what is often the most costly consumable in the mineral processing plant. As he pointed out, grinding media selection and quality control can play a major role in successful plant operation. Owing to the economic importance of this topic, there are some important factors related to media sizing that I believe merit further comment. Dunn made reference to a slightly simplified version of the Azzaroni (1981) equation and pointed out its successful use for the Henderson SAG and Climax ball mills. Although both formulas are empirically based on successful plant experience, a notable discrepancy between them is that Bond has factored the work index by the ore specific gravity. This is invariably so, as the Bond work index is derived from the mass grindability (in grams per revolution) measured in a test mill with a fixed volume of solids load (Bond, 1961). A material having the same structural integrity but double the density of another will have double the grindability and just over half the work index. Thus, for the general case, specific gravity should be incorporated into any media sizing formulation that uses work index as the criterion for resistance to breakage.

Jan 1, 1990

By Michel Grenier, Gopal Kunchur, Stephen Hardcastle

This paper presents the findings of a dust study in a typical fluorspar processing plant. The primary purpose of this study was to identify employees and occupational groups exposed to high dust levels and determine compliance with personnel regulations for regular and extended work shifts. The range of airborne concentration of respirable silica and fluoride compounds in specific areas and on personnel was determined. State of the art dust monitoring equipment and tracer gas techniques were used to measure dust concentration, pinpoint dust sources and map major airflow trends in the mill. Results of the survey indicated silica dust concentrations in excess of permissible limits being produced mainly by crushers at the south end of the building. Tracer gas releases and gas chromatographic analysis further showed that prevailing south to north air currents tended to carry and spread dust produced by the crushing operations throughout the process plant. Airborne concentrations of fluoride compounds measured during the study were always well below the prescribed threshold limit value (TLV) for the contaminant. Recommendations, including a mechanical exhaust ventilation system on crushers and transfer points, scheduled preventive maintenance on existing bar sprays and wearing of personal protective equipment were made which significantly improved the work environment. Further testing conducted after Installation of the dust extraction system revealed significant improvements in most areas of the mill.

Jan 1, 1991

By N. Santa, V. Salinas

"Printed circuit boards are potentially recyclable materials. Developing suitable methodologies for proper disposal and better utilization, brings major environmental and economic benefits. A methodology for copper recovery using heat treatment before conventional leaching is carried out. A comparison between conventional methodology and the one that includes incineration treatment is presented. It concludes about results and differences in terms of the percentage of copper leached over time. INTRODUCTION The rapid proliferation of electronic devices in the past two decades, has forced researchers to find a solution for one of the most toxic and hazardous materials, the printed circuit boards (Ghosh et al, 2015). For this, countless techniques have been developed, the methodologies includes hydrometallurgy, pirometallurgy, electrometallurgy or a combination between all of them. The amount of precious and base metals in its composition are very attractive and usable to implement methodologies that allow maximum recovery and recycling. This subject has been extensively studied and researched in order to provide solutions to the great problems generated by incorrect final disposal of this waste. Over 150 articles have been widely published in the last 15 years, covering large areas such as characterization of discarded printed circuit boards, health risks associated with processing and different routes of recycling have been analyzed to provide an overview understanding this issue (Ghosh et al, 2015). (Oh et al, 2003) performed a selective leaching of valuable metals from waste printed circuit boards by size reduction, magnetic and electrostatic separation, also leaching with sulfuric acid and hydrogen peroxide, achieving 95 \% of copper extraction. (Chaverra Arias, 2014) proposed a similar methodology to extract copper from electrical and electronic waste, performing similar processes and applying metallic copper electrowining as well as copper oxychloride precipitation. (Silvas et al, 2015) used hydrometallurgical processes for recycling printed circuit boards applying physical processing and copper extraction by selective leaching. (Kumar et al. 2014) conducted a leaching of metals from waste printed circuit boards using sulfuric and nitric acids. Also there have been proposed various methods for recovery of different metals including applying multiple metallurgical techniques that involve both living organisms and high temperature processes such as pyrometallurgical. The printed circuit boards are a very important source of copper, according to several authors mentioned above, the amount of copper on a printed circuit board can reach about 20 \%, because copper is responsible of establishing a conductive layer that will enable the connection between electrical and electronic components. This document proposes a methodology for recycling printed circuit boards and extract copper by selective leaching. The process that is carried out consist in a preliminary characterization and mechanical separation which will condition the material for further hydrometallurgical treatment that includes leaching in nitric acid media 3M."

Jan 1, 2017

By V. B. Achanti, A. W. Khair

This paper deals with the effects of various bit geometric parameters on the failure characteristics of rock material. Improving the rock-cutting efficiency of continuous mining machines has proven to be an interesting research topic during the last few decades. In the current study, an automated rotary rock-cutting simulator, duplicating a continuous miner, was used to study these parameters in the laboratory. The improvement of bit performance in terms of its life, cutting efficiency, dust production and energy consumption has drawn widespread attention. Research has demonstrated that optimizing bit parameters can result in efficient fragmentation of rock. Indiana limestone rock material was used in this study. The bit tip angle, bit tip size, bit spacing, depth of cut and cutting velocity of the rotary drum were varied to investigate the failure characteristics. The cutting pressure, penetrating pressure and the depth of cut were monitored on the simulator during the cutting process. Airborne dust and settled dust were measured for each experiment. Then, the specific airborne dust and specific energy were determined for each type of bit. Triaxial tests were carried out to correlate the failure angle of the rock in the static case to the dynamic cutting process failure. The physical and mechanical properties of the rock were also determined to assess their influence on the wear characteristics of each bit.

Jan 1, 2000