Search Documents

By Norm Steenson

Rapid excavation includes rapid support and is the central theme of this paper. Over the last few years, enormous strides forward have been made in the excavation and material handling aspects of underground excavation. However, the technology necessary to support these rapidly created openings has lagged behind the other aspects. This paper would attempt to bring you up-to-date on the progress made in bringing ground support using shotcrete into the same productivity rates as the other cyclic operations. Shotcrete has become an acceptable material for temporary and permanent support for undergound openings. However, coarse aggregate shotcrete has been an expensive construction material. It has been confined in the main to difficult ground conditions where conventional methods of support have proved to be even slower and more expensive than shotcrete. There are two main factors influencing the productivity of shotcrete equipment. (1) Structural shotcrete as opposed to gunite requires 40% to 45% rock minus 3/4" in the mix design. The equipment to handle such aggregate content has been difficult to develop on a volume basis owing to the attritional nature of the material which causes intense wear problems on

Jan 1, 1974

By Donald L. King, Frank A. Baczek

Sedimentation-based equipment is used in applications where separation of solids from liquid by gravity settling is desired. If a concentrated solids slurry is desired, the equipment is designed to "thicken"; if a clear liquid is desired the equipment is designed to "clarify." Thickeners normally handle higher solids loading rates than clarifiers, which usually process feed slurries containing low concentrations of suspended solids. Thickeners are therefore designed for heavier-duty requirements, and clarifiers have extra features to ensure more complete suspended solids removal. Major components (Figure 1) that are common to all sedimentation-based equipment are: tank, drive-support structure, drive unit and lifting device, rake structure, feed well, and a means of overflow and underflow withdrawal. Specific features are designed interdependently after the overall separation approach is defined conceptually. This conceptual approach is usually based on past experience or evolves from sedimentation studies conducted on samples of the slurry to be handled. Because many variations and combinations of components are possible, the overall conceptual approach has a number of possible designs that will accomplish the desired results. The final choice is based on practicality, potential for minimizing upsets, and cost.

Jan 1, 1986

By B Scheiner, D. A. Stanley

Introduction Treatment of ores to recover metal and mineral values results in waste materials usually in the form of dilute slurries. The US Bureau of Mines (USBM) investigated a technique for dewatering phosphatic clay waste by flocculating with polyethylene oxide (PEO) and dewatering the resulting floes on a static screen and/or trommel screen (Schemer et al., 1985). In the investigation, it was determined that PEO was far superior to polyacrylamide polymers for this type of dewatering. This paper discusses reasons for this superior performance. Comparison of PEO with polyacrylamides Dewatering experiments were conducted by adding PEO solution from a burette to a stirred clay slurry. The dewatering endpoint was characterized by rotation of the floc mass as a unit, a clear supernate, a maximum floc size, and a minimum floc volume. Additional water was removed from the floes by hand squeezing (Schemer et al., 1985). The clays investigated were sodium, potassium, magnesium, calcium, and aluminum exchanged montmorillonite and attapulgite. Nine commercially available (Superfloc) polyacrylamides were compared with PEO at two polymer concentrations. Results are summarized in Table 1. The solids content of the dewatered clays ranged between 24% and 33% and was highest for PEO-treated material. These results and the data in Table 1 indicate that PEO is superior to polyacrylamide in terms of polymer dosage required. Superflocs 16 through 128, like PEO, are nonionic and should give similar results to those for PEO if the flocculation mechanism is the same for both type polymers. Superflocs 204 through 214 are anionic with increasing anionic character from 204 to 214. Generally, the anionic polymers gave the best results for the polyacrylamides tested, but in terms of dosage they were not as good as PEO. Correlation between flocculation and dewaterability of waste slurries The overall mechanism for mechanically induced clay dewatering is not completely known, but certain observations can be made. For instance, when a polymer is adsorbed on a clay such as montmorillonite, the polymer desorbs interlayer water. Polymer adsorption is driven by favorable entropy changes associated with this water desorption. It is also known that the -CH2-CH2- links of the PEO chain are sufficiently hydrophobic to lead to physical adsorption of the polymer (Theng, 1979). For montmorillonite slurries, the sheet-like fundamental particles, called tactoids, consist of a small, variable number of aluminosilicate layers together with interlayer water and exchange ions. The flocculation process consists of adsorption of polymer on the tactoid. Loops and tails of polymer that extend into solution then adsorb on another tactoid, forming a bridge. Mechanical action, induced by hand squeezing or in a trammel, joins the bridged tactoids face-to-face and edge-to-edge to form regions of high density. Similar orientation effects are observed for the needle-like attapulgite crystals (Schemer et al., 1985). Proposed flocculation model Generally, statements concerning flocculation and dewaterability apply to both PEO and the polyacrylamides. However, PEO has additional interaction with the clay material when compared with polyacrylamides. PEO is a polymer with repeating -CH2-CH2-O- groups and interacts with montmorillonite through a water bridge whose strength is greatly influenced by the exchange ion. To obtain insight into this interaction, a series of experiments were conducted in which different ion exchange forms of montmorillonite and attapulgite clays

Jan 1, 1987

By W. G. Pariseau, S. C. Schmelter

The destabilizing effect of water pressure on rock-mass stability is examined quantitatively by the finite element method. A coupled code that accounts for the simultaneous effects of rock-mass deformation and transient fluid flow is used for this purpose. The traditional soil-mechanics assumption of an incompressible fluid is shown to be untenable for the analysis of porous, fractured rock slopes. A Mandel-Cryer effect, whish is a transitory but elevated and potentially destabilizing water pressure following a cut, was not observed.

Jan 1, 1999

By S. Mathur

Oxide particles are commonly used as fillers in plastics, paper, rubber, etc. (particulate composites). The successful fabrication of such composites is dependent upon the adhesive strength of the filler particles to the matrix. The compatibility of the matrix and the filler particles is generally enhanced by the adsorption of surface modifiers such as surfactants and polymers at the particle-matrix interface. To develop a scientific basis for the selection of the appropriate modifiers it is necessary to understand their adsorption mechanisms. specifically, the adsorption of polymeric additives is attributed to a combination of chemical and electrostatic interactions, hydrogen bonding and van der Waals forces. Hydrogen bonding has been suggested to be the primary adsorption mechanism for nonionic polymers. However, a literature survey of the Poly(ethylene oxide) (PEO)-oxide system suggested that PEO, a nonionic polymer, was substrate specific. A systematic study was undertaken to investigate the adsorption mechanisms of PEO on oxide particles. It was determined that strong Bronsted acid sites on the surface interact with the ether oxygen, a Lewis base, of PEO to induce adsorption. In this work, characterization of PEO binding sites on oxides is reported and the mechanisms of PEO adsorption are discussed.

Jan 1, 1999

By Michael G. Nelson

In 1992, the Alaska Department of Environmental Conservation received a grant from the Environmental Protection Agency (EPA) to fund the reclamation of an abandoned placer mine. The project also included the development of a water-quality and hydrologic-monitoring program. The grant was provided under Section 319 of the Clean Water Act and is administered through EPA's Region X Water Division. For the past 100 years, Alaska's interior has been the site of extensive placer-mining operations. Early surface and underground operations left small tailings piles, some of which are still visible. Dredging left larger tailings piles, similar to those in California and elsewhere. The only reclamation of these tailings involved use as road base and fill and other civil applications. Most active mines in Alaska are on state and federal lands. The standards of reclamation for mines on federal lands are established under US Mining Laws, 43 CFR 3809. They address only mines operated since 1981. Under a state statute passed in 1990, the Alaska Department of Natural Resources, Division of Water and Mining, has issued reclamation regulations. These regulations apply to sites on state, federal and private lands, but only those mined since Oct. 15, 1991.

Jan 1, 1995

By A. F. Klebanov, K. N. Trubetskoy, M. Yu Khoudine, V. L. Postnikov

The information system of monitoring of mine receive layouts is being created In the "ROSUGOL" Company for the prompt analysis of the state-of-the-art of mining operations at under- ground and open cast mines of the Company, rapid and effective decision-making and elaboration of recommendations on the basic directions of enterprise development. The data bank storing the digital mapping and attributive information describing the actual background of mining operations at the enterprises of the Company is the core of the system. The Oracle database management system and the ARC1 INFO geographic information system have been chosen as basic software packages for the Project realisation. The updating of the information will be performed on a regular basis via the transmission of actual digital data on under- ground and open cast mine layouts In ARCIINFO conversion to the central office of the "ROSUGOL" in Moscow. Centralised storage of digital mapping and attributive data, database administration and navigation is effected with the Oracle software package. Access to the data in the operation mode with an interactive display map will be effected with the use of the local computer net of the "ROSUGOL."

Jan 1, 1996

By Roderick K. Davey

The objective is to develop a short-range mining plan which satisfies management and operating criteria and also "dovetails" with the long-range mining plan. In the past years, this objective was accomplished entirely by manual methods. Today, the computer is used to assist the engineer with this task. The results provided by these programs usually are incomplete and require further manual manipulation. The advantage of using the computer programs is that the program can be used to evaluate alternative plans on a first-cut basis minimizing the manual work. Subsequently, the most promising alternatives can be analyzed in more detail, commencing with the first-cut results. In this specific case history, one technique for using computer programs to assist with short-range mine planning will be discussed. Some of the basic operating and management criteria considered directly and indirectly are as follows: (1) operating criteria which include minimum and maximum shovel cut size, equipment performance, haulage roads, requirements for blending, and plant capacities; and (2) management criteria which consist of production requirements, cash flow requirements, return on investment, market demands, and availability of capital.

Jan 1, 1979

By Jamal Rostami, Ataollah Rahbar, Jürgen Paulzen

"Uma Oya Multipurpose Development Project is located in South West Sri Lanka. This project, among many components, involves a 14 km headrace tunnel in very hard and abrasive igneous rocks. The tunnel is under construction by a 4.4 m diameter double shield TBM. The headrace tunnel has already reached 5km milestone and has passed through some reaches of tunnel in very strong intact rocks with no joints. Low penetration at high thrust load has caused frequent stoppages for cutter change leading to low utilization and advance rates due to low cutter life. The original machine was dressed with 27, each 432 mm (17 inch) diameter, 19 mm (3/4 inch) tipped disc cutters. However, various cutter diameters of 432-457 mm (17-18 inch) and cutter tip widths 13 to 19 mm (0.5-0.75 in), have been tried to see if cutter life and penetration rates could be increased. This paper will review the history of the project, the geology of the site, along with TBM performance and cutter life. It will focus on frequency of different cutter failures encountered in various ground conditions. Also, results of using variation of cutter diameter and tip width to cope with the hard rock conditions and their results in increasing machine productivity will be discussed. This allows for better understanding of parameters controlling disc wear/life and leads to better cutter management for more efficient operation of hard rock TBMs in similar conditions. INTRODUCTION The Uma Oya Multipurpose Development Project (UOMDP) lies in the south-eastern part of the central highland region of Sri Lanka. The Multi-Purpose Project Of Uma Oya is planned to convey water from Uma Oya to Kirindi Oya Basin for hydroelectric energy generation includes Puhulpola RCC Dam on the Uma Oya river, Dyraaba RCC Dam on the Mahatotilla Oya river, a conveyance tunnel from Uma Oya to Mahatotilla Oya (L=3750m), a long feeder tunnel from Mahatotilla Oya to Kirindi Oya river. The feeder (or power) tunnel Lot consists of a 15554 m long headrace tunnel (HRT), the surge shaft and tank on the upstream of the vertical shaft, a 650 m vertical shaft with steel lining, and an underground powerhouse and a 3650m tailrace tunnel (TRT)."

Jan 1, 2016

By Waclaw Dziurzynski, Janusz Tracz, Danny Wooton, Andrzej M. Wala

The purpose of this paper is to present validation studies of the mine-fire simulator using data gathered from an actual mine fire which occurred in November 1991 at the Pattiki Mine. This study evaluates the suitability of the computer software package for modeling underground fires. The paper also discusses the importance of the on-line monitoring system for the validation process.

Jan 1, 1995

By R. O. Burt

Gravity concentration - the separation of minerals according to their relative density - is one of the oldest forms of mineral processing. Even though modern technology has developed a range of other processes, gravity concentration remains as one of the most important methods employed for mineral separation. The range of minerals recovered covers a wide spectrum, from andelusite to zircon, from coal to diamond, from gold to industrial mineral. The long history of gravity concen¬tration, along with a still imperfect understanding of the various mechanisms involved has resulted in a series of ingenious engineers developing, some¬times perfecting and sometimes rejecting, a wide range of equipment, suited for a variety of different duties. 'Selection' in the context of gravity separation, is primarily the choice of the right type of equipment for the separation in hand; 'sizing' of the correctly chosen unit is, more often than not, determining the appropriate number of units required to suit the throughput. The accent of this chapter will, therefore be 'selection'. A brief description of the major types of gravity concentration equipment will follow a discussion of the factors which determine the selection of the correct unit. CLASSIFICATION OF GRAVITY CONCENTRATION EQUIPMENT All concentration equipment has a primary function and a secondary function. The primary function is the efficient separation of the constituent minerals into two or more discrete phases; the secondary function is to effectively cause the discharge of these discrete phases into separate compartments (Aplan 1975). For maximum efficiency of operation, the forces which effect the primary function should not also result in the secondary function occurring; in such cases optimum operating conditions required for the primary function, separation, may have to be compromised to ensure reasonably efficient operation of the secondary function, product discharge. With gravity concentration, the primary function is effected by the relative movement of minerals of different density in response to gravity and one or more other forces, the latter often including the

Jan 1, 1986

By K. L. Johnson

Networks of monitoring wells were established prior to mining at four longwall mine sites in the Appalachians to monitor the effect of mining on water levels, water quality and well yield. Two of the sites were located in stream valleys and the other two sites were located on hilltops. The depth to the mined seam ranged from 500-850 feet with the deeper cover being associated with the hilltop sites. Maximum declines in groundwater levels during and after mining were an order of magnitude less in the stream valley aquifers than in the hilltop aquifers. However, water levels in hilltop wells located outside the area immediately above the panel were unaffected. Water quality changes in wells as a result of longwall mining were negligible at all four sites. Increases in aquifer transmissivity and well yield were much more pronounced in the stream valley aquifers than in the hilltop aquifers. The significantly larger recharge area for the stream valley aquifers than that for the hilltop aquifers may partially account for the differing responses of these two classes of aquifers to longwall mining. These observations appear to be consistent with the stress-relief fracture model for Appalachian Plateau groundwater hydrology proposed by Wyrick and Borchers in 1981.

Jan 1, 1986

By James I. Mathis

Should an arbitrary reduction factor be applied to laboratory compressive strengths when designing pillars? The answer is, as is the main contention of Peng's article, probably not. Many factors affect the strength of the material remaining in the pillar. On the other hand, outside influences will influence the strength testing results from the lab. This is not the first article, nor the last, to discuss the discrepancy between the two strengths. As was discussed in the article, actual pillar strength is affected by several factors. The two mentioned were: • The scale effect of discontinuities. How large must the pillar be so that the increase in discontinuity count with size will not decrease the strength. • Non-uniform strengths and lithologic units within the pillar. The scale effect of discontinuities is important. What size block must be tested so that the rock mass strength is actually measured? For a highly fractured rock mass, or coal with a high cleat density, this sample may be quite small. Conversely, if an unaltered, moderately jointed, quartz monzonite was examined, the sample block would likely be very large. This is the subject of ongo¬ing research. More to the point, if the tested sample is sufficiently large to model the rock mass strength, then no reductions should be made in the lab strength based on this factor alone. Non-uniform strengths and variations in lithologic units will also affect the pillar strength. I am not an expert in coal mines, having gained my experience in hard rock metal mining. These problems, though, are commonplace. However, strength sampling for pillar strength determination involves sampling material from within the lithologic unit that will form the pillar, not from pieces of material found on the floor. In addition, this sampling should cover the entire range of strengths of the material in the pillar-hard units (such as the partings described by Peng), as well as soft units. Testing results should then be included in the pillar design. Contrary to statements in Peng's article, at least one rock mass rating system (Laubscher, 1990) allows for the compositing of strong and weak units into a design rock mass strength that can be used for pillar design.

Jan 1, 1993

By D. A. Curry

This paper describes a study of the influence of non-normal loading on the indentation behaviour of single bit-teeth. Indentation experiments have been performed on a soft, isotropic limestone using both sharp and blunt 60 degree wedge-shaped indentors constrained to penetrate the rock at 0, 15, and 30 degrees to the rock surface normal. For both sharp and blunt indentors, the normal force required to produce a given normal penetration decreased as the offset of the penetration direction from the rock surface normal increased. The crater volume produced by a given normal penetration with the sharp indentor was largely independent of the penetration direction. In contrast, the crater volume produced by the blunt indentor was increased markedly by non-normal penetration at small penetration depths, because the threshold penetration for chip formation decreased with non-normal loading. The crater volume produced by a given normal force was significantly increased by non-normal penetration, and this increase was particularly pronounced with the blunt indentor. The energy required to form unit crater volume was correspondingly reduced by non-normal indentor penetration. A simple method for predicting the reduction in the rock's resistance to chip formation is outlined, which is supported by the experimental data. The implications of these findings for rotary drilling are considered.

Jan 1, 1986

By Rudolf Kvapil

INTRODUCTION Sublevel mining is a mass mining method based upon the utilization of gravity flow of the blasted ore and the caved overlying waste rock mass. As with any other mining method, sublevel caving has advantages and dis¬advantages which must be carefully considered and evaluated. The major advantages of sublevel caving are dis¬cussed as follows: Because all of the mining activities are executed in or from relatively small openings, sublevel caving is one of the safest mining methods. Drifts, which are the pri¬mary working places, are distributed in a uniform pat¬tern on all levels. Normally the maximum dimensions of the sublevel drifts are about 5 m wide and 3.7 m high. The transportation drifts can have the same section, or the height may be increased to about 4.5 m when trucks are loaded in the transport drifts. The stability and safety of such drifts in competent rock can be easily controlled by smooth blasting or by a combination of smooth blasting with shotcreting. In less competent rock masses, stability can be achieved by combined reinforc¬ing, for example, by a combination of smooth blasting, shotcreting, and rockbolting. The major mining activities can be broken down into three groups: drifting and reinforcing; ore fragmenta¬tion, i.e., production drilling and blasting; and ore draw¬ing, loading, and transportation, and all are relatively simple. Because of the repetitive nature of the mining system, one can standardize almost completely all min¬ing activities. This means that a high degree of work efficiency can be achieved. Because the components of mining production in sublevel caving can be standardized, a high degree of mechanization is possible. In modern sublevel caving the sections of drifts and tunnels are sufficiently large to allow the introduction of large trackless mining equip¬ment. The advantages of a trackless system can be then broadly utilized not only for direct mining but also for all services, including the transportation of mining per¬sonnel to the working place. The flexibility of mining is very good. Standardiza¬tion and specialization of mining activities and equip¬ment on separate levels (lower level or levels in de¬velopment, upper level or levels in production mining) together with the trackless system yield a high degree of flexibility. This allows a rapid start-up of mining and good flexibility in making production rate changes. The method lends itself to good work concentration, organization, and working conditions. Normally, on the lower levels, various phases of development are under¬way. Upper levels are in various stages of extraction. Therefore the work can be easily organized into a sys¬tem which excludes interference between mining activi¬ties. Safety of mining (in small dimension openings), good work organization, high mechanization using large modern mining equipment, etc., comprise very good working conditions. Naturally such a system enables a high work concentration and rationalization of separate specialized mining activities and therefore mining by sublevel caving can be effective and relatively in¬expensive. The major disadvantages of sublevel caving, on the other hand, are: There is a relatively high dilution of the ore by caved waste. Various types of ore loss can occur. When the ex¬traction limit (that point yielding the maximum accept¬able amount of dilution) is reached, the remaining highly diluted ore represents an ore loss. Some ore is lost in passive zones located on the level of extraction between the active zones of the gravity flow. Part of the ore from these passive zones can be recovered together with ore extraction on the lower sublevel, but some un¬diluted and often not fragmented ore located in passive zones above the plane of the footwall is lost. In gen¬eral, these losses are larger as the inclination of the ore body and the footwall is reduced. A relatively large amount of development is re¬quired. This includes transport drifts, usually located in the footwall waste rock on each sublevel, and sub¬level drifts, which connect the active mining areas to the transport drifts and as a result are partially in ore and partially in the waste rock of the footwall. The waste rock length increases as the inclination of the ore body and footwall decreases. It also includes orepasses, used for transport of the ore or waste from the separate sublevels downward to the main haulage level, and normally driven in waste; and inclined drifts or tunnels, which provide a connection for the trackless equipment between the main haulage level and the separate sublevels and are driven in waste. Finally there is the de¬struction of the surface through subsidence. To maximize the ore recovery, minimize the dilu¬tion, and achieve a high efficiency of mining by sub¬level caving, good data regarding the gravity flow pa¬rameters for the blasted ore and the caved waste are of utmost importance. The exact type and amount of data required depend upon the purpose and needs of the study. For the first feasibility study, it may be sufficient to utilize the data from other sublevel caving operations with similar conditions and circumstances. For any higher level of mine planning it is clear that more exact data, including analytical and experimental analyses up to full-scale in-situ testing, are necessary. Basic gravity flow principles and design guidelines for the application of the sublevel caving mining method are presented in the following sections. Although some¬what simplified, they should provide a basis for mine planning and operation. The gravity flow principles described can be effectively applied to other mining situations, with some modification. Also, steep dipping coal seams can be effectively mined by modified sub¬level caving.

Jan 1, 1982

By Ryne Goodnough

INTRODUCTION The Wyodak Mine is located in the northern Powder River Basin of Wyoming and is thought to be the oldest continuously operating coal mine in the United States, having recorded yearly production since 1923. The mine has expanded over its 80-plus-year history from an underground room and pillar operation to a modem surface snip mine. Currently, the mine feeds four on-site power plants using conveyors, has a filly automated truck load-out, and ships coal by rail to nearby Wyoming power plants. Annual production of 4.8 MTFT is accomplished on a single-shift basis with 53 fill-time production, maintenance and administrative personnel. In 1990 a decision was made to modernize the coal feed system to the power plant complex with modular conveying equipment. The project involved constructing coal storage silos, overland conveyors, feeder breakers and modular conveyors to follow the mining benches. Total project cost in excess of $25 million was used to construe or commission: A 2,150-TPH 48-inch overland conveyor with horizontal curve A 2,150-TPH 48-inch plant feed conveyor 13 shuttle conveyors, each 150 feet in length 2 front-end loaders equipped with large coal buckets 2 crawler-mounted feeder breakers with compatible discharge conveyor 1 high-lift shuttle conveyor with adjustable discharge height 1 high-angle conveyor 2 4,500-ton coal silos with automated truck load- out capabilities. Conceptually, the plan was to develop 33 MTONS of reserve adjacent to the plant complex and use front-end loaders to tram ROM coal to in-pit feeder breakers. The primary crushing would reduce coal to 6-inch minus and feed through a series of shuttle conveyors to an overland supply conveyor. The overland conveyor would feed the secondary crusher, and the crushed product would be moved to any of four storage silos using conveyors. The in-pit crushing and conveying system is a unique fit for the power plants and provided many interesting challenges for the coal mine to overcome. System integration, maintenance windows, equipment availability and the like had a major role in engineering the system to a power plant complex having no emergency coal stock- pile and limited plant storage. In crediting the designers and operators, the in-pit conveying system at the Wyodak Mine has delivered coal to the power generators since 1994 with little or no downtime. ENGINEERING CONSIDERATIONS Yearly production for the mine is based on 3.5 MTPY which requires about 1,550 TPH on an 8 hour, one-shift- per-day, 5-days-per-week basis. Considering efficiencies for starting and stopping, crew transport, loader trams, and operational delays, a nominal conveyor feed rate of 2,150 TPH or 72% system utilization was used in engineering design application. This ton-per-hour basis is used to size and commission the remaining components of the in-pit system. Coal quality requirements also played a role in equipment selection. The mine reserve grades vertically and coal from Upper and Lower benches needed to be mixed in any given proportion. This required equipment to be filly variable and capable of producing all or part of the 2,150-ton-per-hour requirement. Bisecting the 80-foot- high coal face for quality required construction of a high lift module capable of reaching a single overland conveyor 40 to 50 feet above the pit floor. Designers built a high-lift, adjustable and portable module specific for this application Having two bench systems capable of each producing the required feed for the power plants required computerized control processes to control on-line production. RSLinx, RSLogix, and RSView were chosen as the communication and control software, and a Data Highway Plus serves as the communication backbone. Each of the two in-pit benches are controlled with a data center equipped with Allen Bradley 5-40 processors. This

Jan 1, 2004

By Eugene A. Lang, William R. Archibald

Early in 1972, Rocky Mountain Energy Company approached MARCONAFLO with a unique request for assistance. They controlled a series of scattered ore deposits in a remote section of Wyoming which had become increasingly valuable despite their relatively small size, great depth and low grade. At the time, MARCONAFLO was in the process of developing a tailings reclaim system which was based on the use of submersible capsules. It appeared that this basic concept might be adapted to slurry uranium ores and pump them to the surface through a bored hole. This presentation will review for you the development of this unique and potentially very important application of MARCONAFLO technology. This first slide (SLIDE 1) depicts the total mining concept envisioned by MARCONAFLO and Rocky Mountain Energy Company. A series of six self-contained mining units would be positioned through boreholes into the ore strata. An oscillating MARCONAJET would direct a high pressure jet stream into the orebody and put it into a slurry which would flow back to a slurry pump. The slurry would then be pumped to the surface and to a collection tank from which it would be transferred to processing. Both the MARCONAJET and the slurry pump would be actuated and controlled by means of a hydraulic power console mounted on the trailer behind the service tower. By means of a high pressure water pump also mounted on the trailer, return water from processing would be delivered to the MARCONAJET to slurry the ore. Tailings would be returned to a backfill unit for redepositing in the mined-out cavities. A drill rig would precede the mining, and it was estimated that this configuration would represent an optimum system for most effective equipment utilization.

Jan 1, 1976

By Robert Stefanko

The widespread and increasing use of electrical power for mechanized power has made a tremendous impact on the coal mining industry. It is probably the single most important factor influencing the productivity of a coal mine. In fact, as a part of a study of 62 coal mines in Pennsylvania and northern West Virginia, plus information that was obtained from other sources, it was possible to show a direct correlation between the rise in the use of electrical power and mine productivity, Figure 1. This increased power demand has not always been achieved through proper planning and a careful evaluation of all design parameters, many of which are not even recognized. The result has been increasing problems in power distribution and utilization establishing the need for scientific studies including considerable underground measurements. Because the cost of power for ton of coal produced is generally a relatively low value, inadequate attention is paid its distribution and utilization. Furthermore, a poor system of records and a lack of adequate measurements add further to a paucity of statistical evidence that would permit a rational analysis of overall power costs. However, the direct cost figure alone is highly deceptive; of much greater value is the indirect costs associated with the use (or misuse) of electrical power underground. Success in highly mechanized mining correlates directly with equipment utilization. Today's machines have tremendous potential capacities but profits are measured in terms of performance and not potential. Thus the reliability of electric motors is an extremely important factor for consideration and the effects of all parameters should be carefully evaluated. Thus while studies are continuing on the evaluation of primary and secondary mine electrical systems with interesting results, this paper will be limited to reporting on the results of a study of a specific motor application.

Jan 1, 1972

By S. Vijayan

Despite the limited demand for rare-earth elements, as well as yttrium and scandium, in conventional applications, the emergence of ne~ high-technology applications such as supermagnets, lasers and superconductors is expected to result in significant demand for some of these elements. This paper examines the anticipated applications and demands for rare-earth elements over the next decade and their implications on the utilization of available resources. Process methods for the recovery of rare-earth elements from conventional and unconventional resources are reviewed in the context of their growing demand. Challenges facing the industries in meeting this opportunity are also discussed.

Jan 1, 1988

By L. A. Puchkov

Problems of how to use artificial intelligence (AI) methods and expert systems (ES) to control complex industrial projects have lately become significant in practical terms. Mining ventilation systems undoubtedly belong to complex multi dimensional objects of control with stochastic nonstationary and nonlinear processes. Formal models based on automated ventilation control, do require awkward algorithmic solutions, moreover, a number of tasks become the operator's headache, and the quality of their solution depends on his experience and intuition. These tasks include: - identifying pre-accidental situations and determining their causes; - making well-grounded decisions with regard to changing ventilation regimes, forecast of mining operations taken account of; - controlling ventilation systems in emergency situations, e.g. when in accident, etc. It is in this context that we have for a number of years been investigating how to practically use AI methods for operative control in dynamic aero-and-gas mining processes, one of our research directions being devoted to working out a consulting programme for the ventilation system operator. Our researching and modeling problem was identification of aero-and-gas situation in different parts of ventilation network and its interpretation in order to determine possible causes for gas regime changing and unexpected consequences. We would single out the following stages in this task: I. Operative information procession coming to the data base from the sensors and analysis of hypothetical versions (using the associative rules base) with regard to factors which have caused significant parameter fluctuations (e.g. C%(t), H(t), Q(t) etc.)., 2. Selection of hypotheses in the knowledge base and forming conclusions in accordance with reliability scale. 3. Clarifying the obtained conclusions in dialogue with the operator. 4. Correcting the associative rules base.

Jan 1, 1992