Search Documents

By G. Raspa

This article describes a procedure for calculating the recoverable reserves of stratified orebodies characterised by a thin and irregular layers. An application on the phosphate deposits in the N'Zeto region of the Popular Republic of Angola is also described. The procedure consists in building a block model of the deposit through the conditioned multivarial geostatistical simulation of small areal units. The recoverable reserves are then calculated and defined by applying to the model a selection processes based on measured geological/economic parameters taken from the drillholes: thickness of overburden and mineralised layers, economic grain-size fraction, grade. The procedure also takes account both of the geometrical constraints of the mining method and dilution. For reasons of confidentiality, a multiplier has been applied to the values adopted for the sampling data.

Jan 1, 1992

By R. Hogg, P. Bunnaul

Sedimentation in highly, flocculated suspensions of fine particles, such as clays, occurs through individual settling units (flocs) that have very open structures and correspondingly low densities (typically less than 5% solids by volume). Such settling processes rapidly lead to the buildup of a bed of flocs that are essentially close-packed, with an inter-floc porosity of perhaps 50%. However, the overall solids content is no more than about 2% to 3% by volume. Consequently, the thickening process is dominated by the bed consolidation rather than by the simple settling of the individual flocs. Experimental measurements of sediment consolidation in flocculated clay suspensions indicate, for a given system, that consolidation rates are essentially determined by the solids concentration and can be evaluated using the classical Kynch treatment. However, these rates are strongly dependent on the physical, as well as the chemical, conditions of the flocculation process. Furthermore, the extent to which gravity consolidation proceeds depends on the total weight of the sediment (i.e., on the bed height and the solids concentration). The implications with respect to thickener operation and the requirements for the laboratory testing for thickener design are discussed.

Jan 1, 1993

By B. K. Kejriwal, A. K. Ghose

Under specific geological environment, the full extraction of a coal seam is not possible either because of its extraordinary thickness or the presence of surface structures and bodies of water or because of the conditions prevailing in upper seams. Not uncommonly, therefore, for working such seams, pillars of coal are left for the permanent support of the overburden, and voids around the pillars are filled with sand to strengthen the pillars and prevent their deterioration with time. However, the paucity of river sand has focussed attention on the need for alternate strategies including trials with partial filling of the voids. This study has sought to examine in the laboratory the effects of partial and complete filling on the ultimate load bearing capacity and post-failure behaviour of small, tall pillars using artificial material.

Jan 1, 1986

By G. T. Adel

The growing interest in column flotation has created a need for a fundamental scale-up procedure which is capable of meeting the necessary design and control criteria for industrial columns. Unfortunately, most of the avail able scale-up procedures deal with column diameter only and not overall column volume. Current work focuses on the effect of bubble size distribution and air hold-up on the scale- up of column volume. A series of pressure transducers has been used to measure air hold-up along the length of a bench-scale column. These measurements have been used to validate a mathematical model of the air phase. In addition to scale-up, the model appears to have the potential for use in control of air hold-up and bubble size.

Jan 1, 1990

By E. Turner

In a joint exercise, the European Commission, (led by DG Enterprise), the EU Member States, the various sectors of the Extractive Industry, and WWF have developed a set of Sustainable Development Indicators specific to the non-energy extractive industries. Of equal significance, a Voluntary Scheme for publicly reporting the data has been created. This paper presents these indicators at the company level and explains the role of companies and trade federations in establishing the reporting process. This has been achieved in just 18 months and the paper identifies 6 Success Factors, which have made this possible. It is believed this is the first Scheme of its kind to be put into place and to have begun operation. It is a model for co-operation between government, the NGO sector and industry. The first set of data, based on the reference year 2001, has been gathered. The SD performances of the European Minerals Industry will be publicly reported on for the first time, on the basis of these 2001 data by industry sub-sector. The Member State level Indicators will follow to complete the picture.

Jan 1, 2003

By R. A. Bergman, P. G. Thornhill

Development of the Falconbridge Ferronickel Process for treatment of lateritic nickel ores began with laboratory work in 1955, the year the Company commenced exploration of its concession in the Dominican Republic. Process development centred on selective reduction originally directed to producing calcines amenable to ammonia leaching, but later found suited to electric smelting. The reduction step of the process was developed in a 25 tpd shaft furnace pilot plant located in the Dominican Republic, to which was later added an electric melting furnace. After almost 3 years of development work on this scale the plant was expanded to 100 tpd for fixing design data for a commercial plant. This took the form of the 30,000 ton per year Nickel Ferro-nickel Complex of Falconbridge Dominicans, which started up in 1971.

Jan 1, 1979

By S. K. Kawatra

Although temperature is known to have a substantial effect on many processes, this parameter has been widely dismissed as insignificant for mineral comminution. For this reason, temperature effects on grinding have largely escaped notice. However, it has been observed that processing plants which are subjected to large seasonal temperature variations show a change in performance which appears to be due to changing feed temperatures. The general effect is an increase of the specific energy consumption as the temperature decreases. In autogenous mills, an increased rate of production of critical-size material has also been observed. This is due, at least in part, to changing rheological conditions in the mill, with the slurry viscosity increasing markedly at low temperatures. Mechanical changes in the rock with temperature, such as increased brittle fracture, is also responsible for a portion of the observed seasonal effect, and may account for this phenomenon being observed only in certain plants.

Jan 1, 1989

By Robert H. Merrill

The art of rock mechanics has been applied in various forms since early man first used caves for housing and fashioned rocks into weapons, tools, and utensils. The development of the science of rock mechanics has occurred in a slow but steady fashion due to the complexity of the materials, geometries, and loading conditions involved. It encompasses a great diversity of topics ranging from techniques for rock destruction to those required for rock strengthening or support, and as such enters daily into the life of the mining engineer. Although today rock mechanics can be confidently used in competent geologic structures, the degree of confidence diminishes as the structures become more complex and the number of geologic defects become more numerous. Even so, the principles still give a better estimate of the structural behavior of underground openings than ever before, and the persons responsible for design and control draw freely and often on the subject. For the most part, the civil engineer will spend more time and money on pre-design than the mining engi-

Jan 1, 1982

By M. J. McPherson, P. Mousset-Jones, G. Danko, F. Calizaya, K. You

The friction factor is one of the more difficult parameters to determine in ventilation planning. In practice, this can be estimated from published factors such as those of McElroy. The problem with this approach is that the selection requires some judgement, and the estimated values offer no more than guideline accuracy. This study, examines the effects of four factors on the coefficient of friction for a simulated mine airway. The factors are: airway cross-section, asperity height, flow direction, and cross-cut spacing. The study includes the modeling of a mine airway and the evaluation of the results from 13 experiments on flows of air over rough surfaces. The model, physically represented by a wind tunnel, includes a rough surface section which can be modified to simulate mine airways of various shape and asperity height. Most of the experiments were performed under controlled flow conditions during which the Reynolds number was varied between 50,000 and 300,0000. Based on this study, the friction factor for a mine opening was found to depend not only on the size and shape of the surface asperities but is also affected by the orientation of them in relation to the flow direction.

Jan 1, 1991

By Deepak Malhotra

Comminution circuits in general account for fifty percent of capital and operating costs for a processing plant. Significant advances have been made in optimization of these circuits. One would expect a few circuits to be the favored designs for plants. Review of grinding circuits worldwide indicates that a variety of circuit designs are utilized for non-technical reasons. A brief review of circuits and reasons for their selection is given in this paper.

Jan 1, 1998

By D. Butler

Lateral density changes in the subsurface cause a change in the vertical pull of gravity at the surface. By very accurate measurement of gravity and the practical application of common sense, a microgravity survey can sometimes detect natural or man-made voids, bedrock profiles, and geologic structures of engineering interest. This paper will give some practical guidelines for the application of microgravity surveying. Emphasis in many papers (Blizkovsky, 1979, Fajklewicz, 1983) has been on the anomaly size: herein emphasis will be placed on detectability and signal-to-noise ratios. First, some easy to use curves for anomaly valuation are adapted from Arzi (1974). Secondly, the predictable noise sources are discussed. Thirdly, representative models of abandoned underground workings are evaluated for microgravity surveying given the probable noise in the survey results.

Jan 1, 1988

By Ian Larkins

The Ruby Hill Mine agglomerates crushed low-grade ore (nominally -1 .5'') with high-grade filtered tailings (filter cake, nominally 80% -65#). Cement is added as a binding agent. The agglomerated ore is then conveyed and stacked on the heap. In 1998 approximately $480 000 was spent on cement for agglomeration. Cement for mill pH control and agglomeration was the largest single reagent cost at Ruby Hill. In an effort to reduce agglomeration costs a test-work program was initiated to investigate alternative binders and optimum binder additions. This paper summarizes the test­work results to-date.

Jan 1, 1999

In addressing the challenge of sustainable development, the North American mining industry finds itself operating in two culturally distinct frameworks. Companies are based in the developed world where a profoundly environmental ethic prevails with an emphasis on inter-generational equity – preserve now for the future. Increasingly, their operations are in the developing world where the emphasis is on intra-generational equity, and the distribution of wealth – providing opportunity for improvement today. The paper discusses the further implications of these realities and the factors facilitating or hindering the ability of mining companies to meet social expectation in these two distinct global cultures.

Jan 1, 2004

By Thomas W. Healy, David V. Boger, Yee-Kwong Leong, Lee R. White, Peter J. Scales

The concentration of mineral slurries by conventional thickening devices is discussed. The role of additives on the compression of mineral slurries is also examined. Results for a range of flocculation conditions are presented. The compression of flocculated mineral slurries is found to be highly dependent on the fundamental particle-particle interaction forces and hence, the rheology of the particulate fluid. It is demonstrated that a detailed knowledge of the properties of both the mode of operation of the thickening device and of the solid/liquid interface is required for improvement in the rate and in particular, the extent of dewatering.

Jan 1, 1995

By H. Pieterse, K. S. Fraser, J. R. Goode

The Goldstrike autoclave plant is designed for the pressure oxidation of 1363 t/d (1500 stpd) of refractory gold ore. The plant was commissioned in early February 1990 over a one week period - an unusually short period for a plant of this complexity. The rapid plant start-up is attributed to certain detailed design and control aspects of the plant. This paper discusses key features of the autoclave plant with emphasis on the design of the splash/flash system of heat recovery and the control systems. Commissioning and plant operations over the first three months are reviewed.

Jan 1, 1990

By W. M. Shaver, W. R. Dengler

INTRODUCTION In Canada, most of the rock being broken in underground metal mines is being carried out using traditional drilling and blasting methods. Despite advances being made in hard rock boring and other, more exotic techniques, it is Dynatec's belief that the traditional methods will continue to prevail for many years to come. It is also our belief that modest research efforts expended on the traditional methods will result in substantial financial benefits to the mining and rock tunnelling businesses. Dynatec has pursued productivity improvements through the use of long rounds in both shaft sinking and lateral development. The concept of longer rounds was developed by Dynatec on the Craig Shaft Sinking Project (RETC 1991). This paper reviews the Craig Shaft Long Round success. This technology was subsequently utilized to sink the two shafts at Aur Resources with great success. The development of a Long Round Jumbo for tunnelling is a natural progression of the long round technology developed for the Craig Shaft. RECENT HISTORY OF SHAFT SINKING Shaft sinking is one of the oldest and most difficult mining methods. Due to the relatively small amount of shaft sinking in proportion to tunnelling and

Jan 1, 1993

By D. Tao, B. K. Parekh

Fine coal particles are difficult to separate effectively from liquids or other solids. Ultrasonic energy may be used to enhance the efficiency of the conventional fine-particle separation processes widely used in the coal and mineral industries. Flotation, settling and dewatering tests were conducted using several fine coal samples to study the effects of ultrasonic treatment on these processes. Process variables such as particle size, ultrasonic treatment time and solids concentration were investigated for their impacts on ultrasonic treatment effectiveness. The results obtained from this study showed that ultrasonic treatment is an effective approach for enhancing solid/solid separation in flotation and solid/liquid separation in sedimentation and dewatering of fine coal. SEM microphotographs demonstrate that ultrasonics cleaned particle surfaces, which is, in part, responsible for the observed improvement in fine coal separation processes.

Jan 1, 2000

By Ashis Bhattacherjee, Subrata Chatterjee, Michael T. Dewey, Christopher J. Bise

In order to continue the advancements made during the past two decades in the reduction of the severity of accidents and injuries in underground coal mining, closer attention will have to be paid to the increasing number of accidents resulting in disabling injuries and lost time. With the increased emphasis on safety training reflected in the Federal Mine Safety and Health Amendments Act of 1977 (Public Law 96-1641, and on MSHA's current focus on the application of Job Safety Analysis, it appears that the acquisition, evaluation, and application of accident and incident data will take on an even greater importance. To manage this large amount of information will require a significant commitment of time and attention on the part of mine training departments. A USBM-sponsored research project is currently being completed at Penn State which focuser on the development of a model training program for mining. The program is based on five distinct steps which represent the coupling of a needs assessment with the program implementation. The five steps are: 1) database analysis, 2) workplace observations, 3) identification of trainable problem areas, 4) a library of training resources, and 6) the implementation of the program. In each of these areas, the microcomputer has proven to be a valuable tool for collecting, analyzing, and presenting accident and incident information. This paper will detail the manner in which microcomputers have been fully integrated into the model training program. Examples of applications at existing mines will also be discussed.

Jan 1, 1992

By Ann M. Gosier

Over the past 20 years, diesel-powered equipment has been introduced into the underground mining environment in increasing numbers. While the introduction began years earlier in the metal-nonmetal sector, the exponential growth in coal mining use during this time has been more pronounced. Reasons for the continued use and rapid growth of diesel equipment in underground mines are easily understood. The safety and operational advantages afforded by this equipment in production and support systems are demonstrable. As other mine operators witness the advantages enjoyed by their competitors, they too move to introduce an increasingly diverse array of such equipment into their underground mines. As with any industrial technology, the use of diesel-powered equipment entails potential safety and health concerns. Existing Mine Safety and Health Administration (MSHA)approval regulations (30 CFR Parts 31, 32 and 36) apply only to diesel locomotives and mobile diesel-powered equipment for noncoal mines. In the absence of specific regulations, MSHA has required the use of equipment approved under Part 36 (gassy noncoal mines) for areas of underground coal mines where permissible electrical equipment is required. However, a considerable amount of diesel-powered equipment without explosion-proof or fire prevention features is in use in areas of coal mines where permissible electrical equipment is not required. It is on the use of this latter class of equipment that MSHA is focusing much of its regulatory attention relative to coal. The agency also is focused on revising existing occupational exposure limits for gaseous emissions and instituting limits on diesel particulate emissions for both coal and metal-nonmetal mines.

Jan 1, 1993

By T. R. Ellis

A number of important international events took place in 2001 in the development and evolution of mineral valuation standards internationally. In Canada, the CIMVal Committee released a draft discussion paper for public and industry comment on principles to guide the development of the planned Canadian mineral-property valuation standard. The International Accounting Standards Board (IASB) received comments on its Extractive Industries Issues Paper. IASB will decide whether the financial statements of public mining and petroleum companies will be allowed to provide the value of mineral and petroleum assets on a current value basis instead of an historic cost basis. The author led the Extractive Industries Task Force of the International Valuation Standards Committee (IVSC) in developing its submission to IASB. IVSC intends to develop an extractive-industries valuation section for its International Valuation Standards, which could support the planned IASB standard. In Australia, AusIMM has carried out an in-depth review of its highly regarded VALMIN Code. The AusIMM's MICA subdivision organized the VALMIN `01 Conference in Sydney, Australia, with a range of international and current issues papers published in the VALMIN '01 book. Considerable support for the IVSC initiative was evident at this conference. The results of the review of the extractive industries submissions to the IASB were expected to be released in early 2002. The CMMI Congress in Cairns, Australia in May 2002 is likely to prove to be an important forum for continued discussion of the development and implementation of international standards and qualifications for mineral valuation. The outcomes and implications of these events are discussed.

Jan 1, 2003