Search Documents

By Chikaosa Tanimoto

INTRODUCTION Bratislava is located at the intersection of important traffic routes, including motor-ways, roads, railways, air traffic, trading, and inland waterway with an important harbour. The construction of the D2 Motorway Bratislava, Lamacska cesta Stare grunty was the last missing section of D2 Motorway and its completion linked the Czech Republic through Bratislava to the Hungarian Republic. Traffic was obliged until its completion to use the Lamacska Road and Mlynska Dolina, which were the most heavily trafficked roads in the city. The section of D2 Motorway to be completed in 2006 was 3,300m in length, of which the SITINA Tunnel was approximately half the length. After putting into operation the transit traffic(motorway) and urban traffic was separated. Transit traffic by passing the town was eased. The junctions D2 with Lamacska Road (Harmincova) and Mlynska Dolina also allowed better use of the motorway for the urban traffic The tunnel construction was specified by the features with the highly weathered and thermally altered granitic rock formation with the overburden of Quaternary sediment of 2?4 m thick, very thin overburden, severely controlled deformation limit and environmental protection. The tunnel had to be excavated beneath and nearby the academic complex area and the zoo, where sensitive facilities exist and animals live in. The tunnel consisted of two tunnels (Tunnel A and B) with the length of 1,415 and 1,440 m, respectively. The overburden thickness was in the range from 10?30 m. The standard cross-section and the one with invert arch were 79.5?81.5 m2 and 92.1?93.3 m2. The excavation took 21 months from September 2003 to May 2005. The construction was based on the concept of NATM. The SITINA Tunnel was the third application of NATM in Slovakia, following the BRANKISKO Tunnel (commenced in July 2003) as the first and the HORELICA Tunnel (in October 2004) as the second NATM practice. To protect the surrounding structures and citizens from tunneling operations, seismic monitoring was performed in association with blasting. The allowable limit of blasting vibration was fixed to be under the particle velocity of 15 mm/sec. The tunnel excavation cleared this limit as expected before construction. In driving through the difficult geological situation the excavation work hit 49 faults, and some of them occasionally caused serious face instability. In principle, the rock formation has been affected by the high hydrothermal effect and the resultant clay filing along faults and joints. The auxiliary reinforcement with the 4?8 m long pipe roofing was needed to protect the vicinity of mining face area. This operation extraordinarily required additional works and time which had not been expected before construction.

By Christopher J. Bise

INTRODUCTION Perhaps no other area reflects the art as well as the science of mining-engineering design quite as obviously as strata control. This is due to the fact that the design of mining structures is difficult because rock rarely behaves as a homogeneous medium. Further, the original state of stress and the mechanical proper- ties of the in situ rock are somewhat difficult to deter- mine. However, those aspects that are hard to treat mathematically can and have been successfully approached by model studies and in situ measurements. This chapter will review the fundamentals of strata- control design and will provide examples of applications to typical problems. STRESSES AROUND MINE OPENINGS A close examination of Fig. 1 reveals that, prior to mining, stresses exerted in the overburden can be in both the horizontal and vertical directions. In the example problems of Chapter 1, it was shown that the maximum compressive stress (uv) at any depth (D) below the surface can be approximated as follows: [ ] Further, the lateral stress (oh) is related to the maxi- mum compressive stress by utilizing Poisson's ratio (µ): [ ] As soon as a heading is driven, such as the one in the coal seam shown in Fig. 2, the stresses shift to the sides, or abutments, of the opening. Clearly, these compressive stresses around the opening exceed the pre-mining conditions. The problem of designing an underground opening, therefore, is to determine the maximum stresses and to note if they exceed the ultimate strength of the rock. Table 1 lists several rocks with their corresponding strengths. Figs. 3 to 5 depict the boundary stress concentrations around circular, ovaloidal, and rectangular openings. M is the ratio of the horizontal stress to the vertical stress, or as defined above, p/(l-p). This text will concentrate on the state of stress represented by M = 0.33, which corresponds to the condition of no lateral deformation in a rock having a Poisson's ratio of 0.25. For an ovaloid with an opening width-to-height ratio of 2.0 (Fig. 4), the boundary stress concentrations are at their maximum values at the comers of the opening, with values in excess of 3.0. If the depth of overburden is 500 ft, then the maximum boundary tangential stress ([ ] ) of the ovaloid is: [ ]

Jan 1, 1986

By Jacques Nantel

Mechanization has been at the core of productivity improvements since the industrial revolution. During the past 20 years, mining has derived spectacular progress from mechanization. In the future, however, mechanization alone will not be enough. In the next few decades, automation will bring about new generations of highly productive and safe machines, with low operating costs. Increased use of new and better technology is generally accepted as the prime factor capable of closing the productivity gap. The productivity gap is the difference between inflation and metal prices. The three S-curves in Fig. I represent the evolution of technology in general, and mining in particular. TI represents incremental changes. the dominant sort of technology changes in the mining industry: - Better drills, electric hydraulic drills vs. pneumatic drills, the drilling rate is twice as fast. - Better steel and bits, to accommodate the higher performance drills. - Improved chemical explosives. - Bigger trucks in open pits.

Jan 1, 1993

By D. Brady

The need for onsite gas monitoring during, or following, a major incident at an underground coal mine has long been recognised. Recommendations from inquiries following Queensland mine disasters have included ?qualified persons and equipment for rapid analysis of gas samples be available in times of emergency? and that ?this may be accomplished by either mobile laboratories or laboratories established in each mining locality.? Following the Moura No. 2 disaster, the Queensland Government allocated funds to Simtars for a mobile laboratory to respond should such a disaster occur again in the future. This vehicle was commissioned in 1997 and has been used at many mine sites under a wide range of scenarios. Simtars, armed with over ten years of operational experience with this mobile laboratory, has taken an active role in the design and construction of a modernised replacement unit. With a twenty point tube bundle system and ultrafast gas chromatograph the result is, arguably, the best equipped mobile gas analysis laboratory for mine emergency response in the world. This paper outlines the features of the new laboratory, its capabilities and the philosophy behind the design and inclusions.

Jan 1, 2012

By S. J. Jung

Determining the correct combination of mix components and water for high-density paste backfills with the transport and deposition properties necessary in a mining operation is a difficult task. Rheologic properties cannot be determined without conducting full-scale pumping tests, and data from existing tests are very limited. The following presents the findings of investigations undertaken to determine if paste backfill rheology can be determined using existing techniques and which mix and system variables have the greatest influence on transport pressure loss. Data from lab-oratory-scale pumping tests were used to produce a rheologic model of flow behavior for comparison, and a statistical analysis was conducted to determine the most significant factors affecting transport pressure loss.

Jan 1, 1994

By Yoginder P.

ACKNOWLEDGEMENTS Authors sincerely appreciate the interest, cooperation and technical support of the coal company management and staff in conducting the study. Without their assistance this study would not have been possible. INTRODUCTION AND SPECIFIC OBJECTIVES An area in the midwest overlying abandoned room-and-pillar mine workings at, shallow depth has been experiencing subsidence movements with associated damage to surface structures. Other coal companies in the area have also been having similar experience. A 16 - month cooperative study between a mining company and the Department of Mining Engineering at SIUC was developed with the following objectives. 1) Determine the extent to which surface and subsurface movements were complete in the area, 2) Identify the mechanism(s) of subsidence in the area, 3) Determine the influence of geology and hydrology of the area on subsidence movements, 4) Observe the conditions of abandoned underground workings with a borehole TV camera, 5) Characterize the extent of damage and monitor possible progressive damage to selected surface structures, and 6) Make recommendations to a) minimize further damage to surface structures in the area, b) identify future areas that may be affected by these movements and c) modify mining systems to minimize these movements.

Jan 1, 1986

By H. Lowers, P. Hageman, S. Diehl, D. Fey

Understanding relationships between mineralogy, texture, microstructural features, and element distribution and residence in minerals, is critical for accurate modeling of mineral weathering in waste-rock piles. The morphology of minerals and deformation structures, such as veins and faults, are important factors that control: (1) fluid access to the mineral surface to initiate dissolution, (2) the distribution of trace elements, and (3) formation of secondary minerals. We characterized the mineralogy, textures, and chemical properties of waste-rock material at three sites at scales ranging from outcrop to micrometer scale. A comprehensive hand-sample to thin-section scale methodology utilizing light microscopy, scanning electron microscopy, electron microprobe, and laser ablation ICP-MS was used to thoroughly characterize the waste-rock material.

Jan 1, 2007

By K. M. Kim

A site-specific blasting model has been developed for the Asarco Mission mine. The main inputs to the model are the in-situ block size (F80), the post-blast fragmentation (P80) and the intact tensile strength (To). The output from the model is the specific blast energy (ESE). Modern techniques are being used to obtain the input parameters for the site-specific blast fragmentation model. In particular, image processing software is used to obtain both the in-situ block size and the post-blast fragmentation, and the Schmidt hammer is used to obtain the tensile strength at numerous locations throughout the rock mass. An initial model was developed using five test shots in one area of the mine that contains Argillite and is relatively homogeneous. This also included calibrating Schmidt hammer readings against actual Brazilian tensile measurements. The model for Argillite will be updated as more tests are conducted, and the model will be extended to the other four primary rock types at the Asarco Mission mine.

Jan 1, 2011

By William M. Gleason

Hard times continued to plague the industry when the calendar rolled over to 2000. During 1999, the United States economy had grown vigorously, capping the longest economic expansion in United States history. However, the mining industry was not so fortunate. Commodity prices remained in a slump in the “new-economy” that was fueled by excitement and speculation about the power of the Internet during the infancy of the Information Age. Much of the investment money that once went to mining and exploration was now headed to the world of virtual gold mines. SME President Donald E. Ranta implemented new technology into his plans for SME. His two major goals were new membership growth and to foster the establishment of the comprehensive Internet presence for the Society’s technical information. His strategic priorities included enhancing the quality and quantity of publications, programs, meetings and short courses. “The Internet is the vehicle that will advance the priorities,” he said.

Jan 1, 2007

By John S. Hutchins, David L. Wassum

Mining engineers are ready to take a big step into a new field-oil mining. To understand the subject, one must look at the world's oil supply and demand as well as petroleum technology successes and failures. The US has an abundance of solid hydrocarbon and uranium energy resources, but 75% of its energy for industry, transportation, manufacturing, and space heating comes from liquid petroleum and natural gas. So there are increasing efforts to discover new oil reserves; today the number of drilling rigs operating in the US is at an all-time high. But with 80% of the world's wells already located in the US and Canada, good new exploration prospects are difficult to find. The cost of drilling deep new wells has also greatly increased. The US faced a similar situation in the early 1950s, when primary oil production declines began. During that time, the petroleum researcher introduced secondary recovery techniques such as water flooding and gas injection. This increased the average amount of extractable oil from discovered US reservoirs from 17% to 33%. Production soared and the world petroleum price remained stable until the end of the 1960s. Secondary recovery techniques were then supplemented by tertiary oil recovery technologies-increasing sweep efficiency with such things as CO2 injection-that are, so far, only partially successful in most petroleum fields. Even so, these technologies could raise cumulative recovery expectations to 35-38%. The "lost" oil in depleted US reservoirs equals 48 km3 (300 billion bbl) of conventional oil, or 12 times the current recoverable reserve base. At the present rate of US consumption-1 km3/a or 6 billion bbl/a-this is enough to run the US for 50 years without importing any oil. Moreover, there are 16-24 km3 (100-150 billion bbl) of as-yet unrecoverable heavy oil and tar sands in the US.

Jan 12, 1981

By Roy C. Fedotoff, Jon Hurt, Gregg Sherry, Gilbert Tang

The 1,380 m (4,200 ft) long New Crystal Springs Bypass (Polhemus)Tunnel (NCSBT) will replace the existing Crystal Springs Bypass Pipeline. This tunnel project is part of the SFPUC’s $4.3 billion capital improvement program to repair and seismically upgrade their aging pipelines, tunnels, reservoirs and dams that provide drinking water to more than 2.4 million customers in the San Francisco Bay Area. This paper describes the development of the tunnel alignment and design, and the complex ground conditions of the Franciscan Mélange. Of particular interest is the challenge of tunneling with a possible downhill grade of 3%, a rigorous environmental process and incorporating the lessons learned from 1960s construction of the adjoining Crystal Springs Bypass Tunnel.

Jan 1, 2007

By M. Moagabo

CO2 emissions from carbonate laden reclaimed mine spoil has been shown to pose a hazard to residents in homes built on or adjacent to such land. The objective of this project was to develop a soil CO2 flux survey protocol for assessing reclaimed mine land. The research involved CO2 chamber accumulation flux surveys; stable carbon isotope ratio analysis; statistical hypothesis testing to examine correlation between CO2 flux and soil temperature and moisture as well as spatial dependence; and geostatistics to map CO2 and delineate high flux zones. Soil temperature was observed to have a positive correlation with fluxes while soil moisture was observed to be negatively correlated. Spatial dependence of CO2 fluxes on reclaimed mine land was observed on one of the two study sites. The research suggests that macro-porosity and gas permeability may be important factors that explain CO2 migration in mine spoil. A flux survey protocol has been developed, based on these results, for reclaimed mine lands. The work demonstrates the capability of geostatistical methods to delineate high flux fields. Further research will be required to determine suitable thresholds for such analysis.

Jan 1, 2012

By A. D. S. Gillies

Diesel engine particulate matter pollution is a matter of concern currently in underground mines worldwide. A number of real-time Diesel Particulate Matter (DPM) monitors have been developed in recent years; two of these by the National Institute of Occupational Health and Safety (NIOSH) in the US. One, the D-PDM, is based on an adaption of the successful NIOSH?s Personal Dust Monitor (PDM) unit which is being taken up very successfully for mine respirable dust monitoring. The D-PDM measures all particulate matter within a sub-micron range as classified nominally at 0.8 micrometers by a purpose developed cyclone. The other, the FLIR Airtec, measures the Elemental Carbon (EC) component of DPM by a laser scattering approach. Both instruments have been evaluated underground in robustness and reliability testing in coal mines by the authors. Real time DPM monitors allow greater understanding of the sources and levels of DPM pollution in underground activities. They allow engineering evaluations to determine how conditions can be improved or mining personnel relocated to lower concentration levels. Studies are discussed that examine DPM concentrations from vehicles under varying ventilation conditions. Some of these concern tests undertaken during high activity longwall face moves. They focus on evaluating DPM during the various phases of the face Chock Shield moves. An initiative in some mines has been to limit the number of vehicles in the mining section or panel by the use of a Tag Board or Traffic Controller at the panel travel road entrance to manage exhaust DPM and gases. Diesel tags or tokens are used to control the number of vehicles entering a section or panel and so limit level of pollution. Summation of DPM levels from points monitored throughout a panel demonstrates increasing DPM levels from influence of additional equipment in series within the ventilation circuit. An alternative approach is to invest in underground continuous real-time monitoring of exhaust gases, DPM and section air quantity and integrate this information to determine whether an additional vehicle can enter without exceeding diesel target limit. This optimizes the access of diesel vehicles and replaces the existing manual tag board system. Real-time DPM monitoring allows the industry to pin-point high exposure zones such as those encountered where various vehicles work in areas of constrained or difficult ventilation. Identification of high DPM zones allows efficient modification of mine ventilation, operator positioning and other work practices to reduce underground miners? exposures.

Jan 1, 2012

By Badiozamani Khosrow

Introduction The mining industry has been using computers since the late 1950s. Despite this early start, the use of mine planning software is not a common practice in many operations. But the trend might be changing because of the availability of relatively inexpensive personal computers (PC). The introduction of these machines has generated unprecedented interest by mine managers to computerize their planning operations. However, some managers have become disappointed with the PC's lack of adequate software and the inability to handle the massive amounts of information required for modeling. This paper is an attempt to shed some light on the future of computers in the mining industry. It will examine: • historical progress in the computer industry, • future advances in the computer industry, • historical usage of computers in mining, and • future alternatives available to mining. Historical Progress The computer industry has come a long way since the first full-fledged electronic digital computer Electronic Numerical Integrator And Calculator (ENIAC) was built in 1946. This machine weighed more than 27 t (30 st). It contained 19,000 vacuum tubes, occupied 139 m2 (1500 sq ft), and could perform 5000 additions per second. By contrast, today's fastest, commercially available computer is the CRAY-X. It weighs less than 5 t (6 st), has no vacuum tubes, occupies less than 9 m2 (100 sq ft), and performs over 100 million operations per second. This is an incredible advancement in less than 40 years. One person commented on the rate of advancement in the computer industry. He suggested that if the auto industry had advanced at the same rate as the electronics industry, we could buy a Rolls Royce for $2.75 and it would run

Jan 9, 1984

By Stuart Lister

"When MacLean Engineering chairman and founder Don MacLean got the first question from a minesite about the possibility of addressing ventilation limits through incremental fleet electrification, he was intrigued. It was back in 2015, and the MacLean scissor bolter was already diesel-electric (jumbo trailing cable), so it made sense to him that if they could engineer a battery drive system for the unit’s tramming cycle, they would have the inaugural electric vehicle (EV) MacLean unit.At that time, there were not any entirely diesel-free hard rock mines in existence on the planet, and that remains the case to this day — although the Borden project in northern Ontario is progressing toward that goal (see page 33). This meant there was essentially zero market demand for battery electric vehicles as well as a complete lack of battery technology to address the battery electrification of heavy haulage. Heavy haulage is the part of a typical mine’s mobile fleet with the largest footprint when it comes to diesel particulate emissions, greenhouse gases and wasted energy in the form of heat.Three years later — the wave of battery electrification that is currently picking up speed across the mining industry promises to hit full swing by the early 2020s when a slew of new build, diesel-free mines will start construction. But this movement toward emissions-free mobile fleets is not a completely new phenomenon. Instead, it is an updating of mining technology from a previous generation. What is going on now is the re-electrification of mining. Up until the 1960s, early generations of battery technology (lead acid) and electric locomotive systems were the norm for material and ore haulage in Canada and elsewhere.The thought of a coming paradigm change in mining was particularly pertinent to Don MacLean back in 2015, as he had been part of the era that ushered in the first generation of rubber-tire diesel equipment, when he was a divisional foreman with Inco in Sudbury in the 1970s. He was part of the operating team that was tasked to build a rail loop on one extraction level of the mine. At that time, events on the ground overtook the project, as diesel-powered mobile equipment became a viable option. Once the first diesel scoop was introduced at Creighton #3 shaft, it was clear what the power, haulage capacity and mobility could do for operations and that era of electric rail haulage underground was effectively over."

Jan 10, 2018

By K. Fleck

Energy West Mining Company (EWMC) has implemented a geologic program for improving stability and support requirements along deep two-entry longwall gateroads at its Deer Creek Mine operations located near Huntington, Utah. Together with geotechnical monitoring and concurrent review of mine seismicity in cooperation with MTI staff, it has become possible to improve longwall layout designs for two seam extraction of the Hiawatha and Blind Canyon seams. The geologic program consists of surface and in-mine exploration drilling, surface and in-mine geologic mapping, rock mechanics testing and detailed measurements of changes in depositional and structural conditions during development of every longwall gateroad. The geotechnical program consists of underground measurements at seven locations in two neighboring mining districts located in the Hiawatha and Blind Canyon coal seams under moderate to deep cover. Within the last five years, additional measurements, including data on seismicity and face conditions, have been incorporated into the data collection program for verifying the insitu coal strength and load transfer mechanisms for improving two-seam designs and support systems. Geologic mapping results are also used to predict local stability of headgate and tailgate entries, combining mine roof mapping, stratigraphic profiles of the coal and roof, and depth-of-cover information and dual-seam mine overlays, for use by operations personnel in planning roof and rib support for the retreating longwall sections.

Jan 1, 2012

By W. L. Jacobsen, T. L. Dyer

Cortez Gold Mines is completing a Feasibility Study for a new open pit gold mine in north central NV. The production schedule calls for a peak in material movement. This schedule is based on current operational efficiencies and equipment parameters observed at the company’s existing open pit operation. To mitigate risks of over/under predicting production, simulation modeling was used to validate the loading and haulage requirements during the peak production period. The advantage of simulation is the ability to provide a realistic model of a mining operation based on scheduled, and unscheduled random events during the period under analysis.

Jan 1, 2006

By T. Burchett, F. Stanley, K. McGough, G. Luttrell

The vast majority of U.S. coal preparation plants utilize screen-bowl centrifuges to dewater their fine clean coal products. In light of this popularity, researchers at Virginia Tech have engaged in a variety of laboratory and industrial field test programs to develop technological enhancements that have the potential to further improve the performance of this important solid-liquid separation process. These enhancements, which include simple design modifications and new reagent packages, have been shown to significantly improve solids recovery and reduce product moisture in several experimental trials.

Jan 1, 2006

By M. Bennett, L. Twidwell

Montana Tech has embarked on a coordinated series of studies to delineate the characteristics of the Berkeley Pitlake containing over 36 billion gallons of acidic, metal-contaminated water formed after the cessation of open-pit copper mining in Butte, Montana, USA. The objectives of the overall series of studies are to summarize presently available information and to generate new and needed information to formulate a conceptual environmental model for the pitlake and to provide characterization data for the development of advanced treatment technologies. In this presentation, the chemistry of the Berkeley Pitlake water is partially reviewed. It is known that the pitlake consists of two distinct layers of water referred to as surface and deep water. Samples of deep water were collected and placed in a 12-ft high and 6-inch diameter column and exposed to different wavelengths of UV radiation as well as atmospheric conditions. Measurements of pH, redox potential (EH), dissolved O2, turbidity, conductivity, temperature, and elemental composition show that the water reacts differently and indicates that the diurnal effects of sunlight likely play a major non-biological role in its chemistry. Resulting technology could be useful for developing an alternative to treating acid-rock drainage.

Jan 1, 2007

By F. Calizaya

This paper describes the basic requirements for the utilization of belt air to ventilate working sections at remote locations in relation to the main fans. It highlights the risks involved, potential problems, and the provisions that must be followed by mine operators for the safe use of belt air. The paper also presents a brief review of the current regulations, conveyor belting tests, atmospheric monitoring system requirements, and the experience gained by mine operators to utilize the belt entries to ventilate remote working sections or areas where mechanized equipment is being installed or removed. The paper concludes with a set of recommendations with respect to the utilization of belt air and the composition of belt material in under-ground coal mines.

Jan 1, 2008