Search Documents

By Dion Weatherley, Raúl Castro, Pablo Cid, René Gómez

In underground mining, hang-ups due to coarse fragmentation are frequently observed in drawpoints, drawbells, and ore passes during ore draw. Hang-ups can often require operational interference and hang-up removal activities. Drawpoint and drawbell design has been shown in some studies to influence hang-ups; however, the full extent of this influence remains open to question. In this study, the discrete element method was used to analyze the effect of hang-ups on three distinct drawbell geometries: the Drawer type, Circular type, and El Teniente type. The drawer type was used as the base case given that data was available from a physical model in which hang-ups were studied. The drawer type base case data was then used to calibrate our numerical model. Results show that the El Teniente drawbell geometry sustained 13% more hang-up events as compared with the base case, while the circular drawbell geometry had 16% fewer hang-up events than the base case. From this study, it can be concluded that fewer hang-up events will occur with a rounded drawbell geometry.

Apr 11, 2023

By K. B. C. Brady, B. E. Scheetz, J. E. Cuddeback, T. W. Bergstresser, W. A. Telliard, S. C. Parsons, R. J. Hornberger

Two weathering procedures are being developed by the Acid Drainage Technology Initiative in cooperation with federal agencies(OSM and EPA). Objects are to: (1) standardize existing humidity cell and leaching column procedures; (2) improve test methods by maintaining a carbon dioxide enriched environment needed to optimize carbonate mineral dissolution, and quantifying particle size variables to evaluate reaction kinetics, and (3) provide flexibility in test method implementation consistent with EPA guidelines for Performance-Based Measurement Systems. Preliminary results indicate the CO2enriched leaching environments produce alkalinities that are similar to field observations and greater than the tests run under atmospheric PCO2. Leaching columns produce higher alkalinity than humidity cells.

Jan 1, 2003

By Johannes Wageneder

As a reaction to the fire accidents in tunnels in Europe Designers nowadays have to demonstrate the integrity of underground structures such as metro systems, railway and road tunnels in case of fire load wherever as a consequence of a lining collapse surface infrastructures or residential areas could be affected. To respond to this FLAMDOCS allows to calculate the stability of reinforced concrete structures during fire load for a series of prede?ned time steps. Elementary theories of non linear material properties and reinforced concrete structures are used.

Jan 1, 2003

By David A. Milligan, William Cobb

2.1 INTRODUCTION This chapter provides the reader with a sense of how a heap leach project may make an orderly, and hopefully non-traumatic, transition from discovery or acquisition to project construction. In making this transition a project can pass through several project development phases (i.e. ore definition and delineation, conceptual engineering, detailed engineering, and ultimately on to project construction and operation). "Go" or "no go" decisions may occur at any point in each of these phases. The transition from ore definition to detailed engineering should be accomplished via a well thought out program of interdisciplinary studies and an integrated, interdisciplinary project team. This chapter also describes, in general terms, a "roadmap" approach to the project evaluation process that must occur as project planning and development progress. It is the experience of the authors, as well as a myriad of companies who have been through the heap leach project development process, that a systematic approach will save many headaches, and many dollars. In fact, it is safe to say that a project with no formalized system of "objectives setting" and "milestone charting" may well flounder along the way, even if an economic ore body exists. Many papers and technical articles have been written about various aspects of mineral resource appraisal, economic evaluation, and mine development. Most of these invoke the same general philosophy of a systematic approach to project evaluation and development, although methods cited for attaining goals are quite variable. This is undoubtedly appropriate, given the fact that there is great variation in approach to project development (e.g., climatic considerations, ore body size and physical ore characteristics, permitting constraints, etc.). For the purposes of this chapter, two primary sources of information have been used to highlight the "road map" approach previously alluded to. These sources are cited throughout the text as Mackenzie (1980) and Snow and Michel s (1986). A brief summary of each of these sources is provided below: Brian GJ. Mackenzie of Queens University (Mackenzie, 1980) has developed a wealth of information concerning project development topics. Much of this information is synthesized in his notes for a short course entitled : "Mineral Exploration Planning and Economic

Jan 1, 1988

By K. C. Shaver

The Sloan Ranch kimberlite complex is located approximately 130 km north-northwest of Denver in the Precambrian core of the northern Colorado Front Range (Figure 1). A Devonian age for the complex is suggested by the fossil assemblages in limestone xenoliths (Chronic and others, 1969), and by paleomagnetism of the kimberlite (E. E. Larson, personal communication, 1986). The presence of diamond was first reported in rocks from the Sloan diatreme by McCallum and Mabarak (1976). Prior to this time, the distinctive- appearing host rock of the Sloan diamonds had been quarried for use as terrazzo stone; examples may be seen in the floors of the airports in Cheyenne and Laramie, Wyoming. The Minerals Division of The Superior Oil Company obtained a lease on the Sloan property in 1980. During the next four years Superior built and fine-tuned a highly efficient diamond recovery facility, explored and tested the Sloan deposit, and used Sloan as a site for testing numerous exploration techniques for future use in a continuing exploration program in the Colorado-Wyoming kimberlite province. The Sloan property was ultimately determined to be sub- economic, but the lessons learned there have been very helpful in subsequent exploration efforts.

Jan 1, 1987

By Andrew J. Regis

Resource figures for bentonite clays are generally based on stratigraphic, sedimentary geologic data and drilling and sampling. Estimates of bentonite resources and/or reserves commonly found in the literature report on bentonite occurrences in specific localities or areas but none on any documented comprehensive estimates of bentonite resources. From 1974 thru 1977 the Bureau of Land Management conducted extensive studies of the resources of commercial grade bentonite in the three state region. These investigations consisted of: 1. Stratigraphic and geologic sampling with supplemental drilling data, followed by geostatistical analysis. 2. Data compiled from a systematic search of county and state records on mining locations, leases and acreage filed for bentonite. Estimates of resources of commercial grade bentonite using industry parameters were calculated from these data sources. It is concluded that there exists from 1.5 to 2.4 billion tons of in-place bentonite in Wyoming, Montana and South Dakota. Assuming a 5 percent annual growth rate for the industry, this would indicate a life of 62 to 73 years.

Jan 1, 1979

By J. W. Mausteller

Chemical oxygen supplies have been used for nearly 60 years, with their greatest application during the last 25 years. They are of two types, the superoxides and chlorate "candles", The superoxides are demand chemicals, responding to the needs of the user and to supply oxygen and remove carbon dioxide. Chlorate candles are formed solid element which furnish oxygen only and do not remove carbon dioxide. Properties of these materials will be described, with comments on the respiratory requirements of a man under various workloads, types of equipment which use chemical oxygen, comparison with other systems and potential application to an underground mine survival system.

Jan 1, 1971

By W. F. McDermott

One of the major improvements in ore grinding economics in North America has been the introduction of autogenous grinding. The history of this has been well documented in previous AIME presentations and in the literature. Pickands Mather & Co. has been very active in the development of autogenous grinding since 1957. This early work led to the application of autogenous grinding to the Wabush Mines ore in 1965, with the installation of 6-24 ft. diameter by 8 ft. long - 1,750 HP mills. Development work recently completed in 1971 on another ore has led to the decision to install 5-36 ft. diameter by 15 ft. long - 12,000 HP mills when this project goes ahead. Between these two decisions lies a tremendous amount of research, development, and application of autogenous grinding to a variety of ores. The Pickands Mather Metallurgical and Research Laboratory in Hibbing, Minnesota has tested, in its pilot plant facility, ores from 9 different deposits. Some of these deposits have as much difference within their own ore types as there is between the various deposits. Therefore, it is safe to say that over 20 different ore types have been tested and flowsheets developed for commercial applications. Of the 9 projects, 3 are in operation. These are Wabush Mines in Labrador, Canada, (1) Savage River Mines in Tasmania, (2) and The Griffith Mine in Red Lake, Ontario, Canada. (3) Pilot plant work has encompassed over 300 individual tests. These tests were carried out in mills that were 5-1/2, 8, and 12 ft. in diameter. Grinding power requirements for the primary autogenous milling has varied from 2 to 30 KWH/Lt of crude ore.

Jan 1, 1972

By R. L. Miller

Two samples of iron enriched basalt (IEB) containing simulated nuclear fuel and having two distinct microstructures were prepared and tested for uranium recovery. The IEBs are refractory towards leaching by ground water. However, the uranium content (15.8%) is high enough that if aggressive leaching techniques are used for uranium recovery, these materials could be considered as man-made uranium ores. The IEBs discussed in this report were prepared to simulate Three Mile Island-2 core debris. The crushed IEBs were treated using three different methods simulating potential industrial scale processes. In one method the IEBs were fused with sodium hydroxide then the cooled mass leached first with water then with dilute sulfuric acid; about 52% of the uranium was recovered in this case. In the second method the IEBs were treated with a sulfuric acid/hydrogen peroxide lixiviant and about 13% of the uranium was recovered. In the third technique the IEBs were leached with a sodium carbonate/sodium bicarbonate/hydrogen peroxide solution. Only about 0.1% of the uranium was recovered. The results of these screening tests suggest that the IEBs can be successfully treated for recovery of the contained uranium. Other studies would be required to determine if other values, such as zirconium or silver, could be recovered from the IEBs.

Jan 1, 1984

By Michael Fehler, Hidenshi Kaieda, Leigh House

Hydraulic fracturing has gained in popularity in recent years as a way to determine the orientations and magnitudes of tectonic stresses. By augmenting conventional hydraulic fracturing measurements with detection and mapping of the microearthquakes induced by fracturing, we can supplement and independent1 y confirm information obtained from conventional analysis. Important information obtained from seismic monitoring includes: the state of stress of the rock, orientation and spacing of the major joint sets, and measurements of rock elastic parameters at locations distant from the wellbore. While conventional we1l 1ogging operations can provide information about several of these parameters, the zone of interrogation is usually limited to the immediate proximity of the borehole. The seismic waveforms of the microearthquakes contain a wealth of information about the rock in regions that are otherwise inaccessible for study. By reliably locating the hypocenters of many microearthquakes, we have inferred the joint patterns in the rock. We observed that microearthquake locations do not define a simple, thin, planar distribution, that the fault plane solutions are consistent with shear slippage, and that spectral analysis indicates that the source dimensions and slip along the faults are small. Hence we be1 ieve that the microearthquakes result from slip along preexisting joints, and not from tensile extension at the tip of the fracture. Orientations of the principal stresses can be estimated by using fault plane solutions of the larger microearthquakes. By using a joint earthquake location scheme, and/or calibrations with downhole detonators, rock velocities and heterogeneities thereof can be investigated in rock volumes that are far enough from the borehole to be representative of intrinsic rock properties.

Jan 1, 1986

By J. Driscoll

After 30 years of success, Newmont Gold Company has temporarily ceased production from the original Carlin Pit. In late 1993, the Carlin East Decline was driven and an extensive underground exploration program was started. Today, Newmont Gold produces refractory ore from the Carlin East underground at the rate of 700 t/d (770 stpd) for an annual production of over 100,000 ounces. Over 70 underground miners enjoy the estimated 6-year mine life at Carlin East. About 70% of the ore at Carlin East is mined by mechanized longhole stoping with delayed cemented backfill. The remaining ore is mined by underhand drift and cemented fill methods.

Jan 1, 1997

By H. P. Ehrlinger

The Negociacion Minera Santa Maria De La Paz mining operations are located at La Paz (some eight miles West of Matehuala), State of San Luis Potosi, Mexico. These operations consist of a single copper-silver property, called the Dolores mine and a number of silver-low base metal properties. The ores from these several mines are transported by rail, or truck, to the central milling unit. The milling unit has two separate sections to treat the two types of ore. The ores from the several silver-base metal mines are mixed at the mill as they arrive. Up to the present time the silver-base metal ores have been milled to produce a bulk concentrate which carries valued in gold, silver, copper, lead, zinc, cadmium and considerable arsenic. In such concentration the zinc and cadmium values are lost to the operations in their liquidations as they are shipped as lead concentrates. Since these ores have exceptional quantities of arsenic which is concentrated in the milling process, these bulk concentrates have to be sent to a smelter for pre-smelting operations to remove the arsenic.

Jan 1, 1964

By A. J. Neale

Much has been published lately about the application of advanced control strategies in the automatic control of autogenous and semi-autogenous grinding circuits. The application of adaptive control algorithms, self-tuning controllers, state estimation, and expert systems has been well documented. While these approaches can be very effective; experience has shown that quite often simply "fixing the fundamentals" can have a significant positive impact on overall grinding circuit performance. This paper will highlight the results of process optimization and process control work by the authors at a variety of autogenous and semi-autogenous installations. A review of one approach for quantifying the mill load/bearing pressure/power relationship is provided. Accurate monitoring of key mill process variables is a necessary prerequisite for both effective process analysis and process control. This paper discusses some of the concerns related to defining steady state operating conditions and the issues related to signal conditioning. The paper concludes with a discussion of an effective application of algorithmic constraint control which incorporates many of these considerations.

Jan 1, 1994

By Henry N. McCarl

[ ]

Jan 1, 1966

By S. Lin

Fan stall is a notorious phenomenon with axial-flow fans. When multiple fans of this type serve a ventilation system, their mutual impacts are very complicated and not well understood. Results from laboratory experiments indicated that the immediate consequence of a fan working across its stall zone (i.e., the pronounced trough on the fan characteristic curve) is that some branches in the system may suffer abrupt and even drastic changes in air quantity and pressure. The quantity range of the fan that causes the abrupt change is called an unstable operating range. The corresponding quantity range of a branch is called a non-achievable quantity range of the branch because any quantity within this range cannot be achieved without changing some parameters of the ventilation system (e.g., branch resistances). These concepts are introduced based on the test results from tubing networks to bring attention to these important characteristics of ventilation systems.

Jan 1, 1996

By Daniel Lum

The limestone resources of Hawaii are derived chiefly from emerged fringing coral reef and coastal dune deposits of Pleistocene age. These deposits are most abundant on the island of Oahu and other older islands and least abundant on the island of Hawaii, the youngest. Their origin and depositional environment were influenced by glacio-eustatic rising and falling of sea levels during Pleistocene time. Dredged reef limestone deposits from two deep-water harbor projects have provided additional resources. Limestone uses include cement and lime manufacturing, concrete sand and aggregate, mad base material, beach sand replenishment, agricultural lime and golf course construction.

Jan 1, 1982

By Blagoj Golomeov, Boris Krstev

Nowadays, in the papers of authors in the area of flotation concentration, we can find several equations that describe the kinetics of flotation process as follows: Agar's equation, Klimpel's equation, Beloglazov's equation and Group of authors' equation (equation with two kinetic constants). This paper makes an attempt to determine the most appropriate equation for mathematical interpretation of kinetics of the SASA mine rougher Pb - Zn flotation.

Jan 1, 2002

When I wrote the Railroad portion of "Mining Engineering" magazines 94 Powder River Basin (PRB) Coal Article I described to you some definite destinations the Railroads had in mind. As with many destinations, the ones I wrote of turned out to be merely stops on the way to places that we have yet to reach. Somewhere along the way we discovered that making it better is a continuous process not just something that you can do in phases I, II, III, & IV. We always knew this I suspect, but perhaps not at the awareness level that exists in RR environments in 1997. The purpose of this article is to update the 94 article, which I could do very quickly. Everything I told you we were going to do in 94 is done, end of story! But in addition to making it a very short article it would not be telling you the things RR has done beyond what we were planning in 94 and for the future.

Jan 1, 1998

By E. G. Hoover

In the mid-I 970s the rallying cry sent out by the aggregate trade associations to aggregate operators was to come to Washington and help design national legislation mandating reclamation of pits and quarries. This collective effort paid off in that aggregate operators were able to assist in the design of "livable" legislation; however, the coal mining industry took some very hard hits. A principal argument used by the aggregate industry was that relatively small parcels of land are impacted, the operations are located in or near urban areas to serve in the development of that immediate area, and are of many years duration; whereas, coal strip mines disturb many acres, are of short duration, and whose products may have world or nationwide utilization. Historically, developments in reclamation are tied closely to the regulatory systems that have been created to control environmental effects of mining. Since reclamation generally results in a cost incurred after the stone, sand and gravel has been mined and does not add to the inherent value of the mineral, there was little incentive in the past for mine operators to reclaim the land. In 1977, the Surface Mining Control and Reclamation Act (SMCRA) became the law for coal mine operators. The law states that, among other provisions, reclamation must "restore the land affected to a condition capable of supporting the uses which it was capable of supporting prior to any mining, or higher or better uses". It is of interest to note that years before the initiation of legislation leading to SMCRA twenty-eight states already had reclamation regulations that covered virtually all minerals. The scope of performance standards found in the state reclamation regulations included slope stabilization, grading, revegetation, neutralization of toxic materials, visual screening, waste disposal, control of drainage, and other sources of pollution and erosion. Environmental legislation and the consequent regulations came about because the public perceived that private industry did not properly value environmental quality and as a result the government became the policeman.

Jan 1, 1998

By M. C. Roberts

In assessing the future markets for a mineral from a producing district, three key aspects must be considered: 1) the future growth in markets, 2) the competitiveness of the district in terms of production costs and reserve adequacy, and 3) the competition from alternative sources of supply. This paper will focus on the first issue by developing a method of predicting the demand for phosphate from the trends in the major markets for phosphate products, primarily the fertilizer and agricultural markets. The paper will show how broad changes in the final end use markets for phosphate products have evolved over time and how this has affected the needs for phosphate rock. These trends are then projected into the future to make an assessment of future phosphate requirements.

Jan 1, 1998