Search Documents

By Richard F. McFarlin

INTRODUCTION Phosphate, one of the three major elements essential for all living plants and animals, has been mined in Florida for over a hundred years. Comprising roughly 80% of the U.S. total and 25% of the world's supply, the bulk of the 35 to 40 million annual ton output is converted to chemical fertilizers. With the exception of one mine in north Florida near the Georgia state line, today's mining activities are centered in the middle of the peninsula just east/southeast of Tampa in Polk, Hillsborough and Hardee counties. These "bone valley" deposits extend into Manatee and DeSoto counties, but there is little active mining there as yet. Because strip mining is, perhaps, the ultimate environmental insult and because Florida has a proactive environmental community, it is not surprising that the mining of phosphate rock has become increasingly controversial. This paper describes how phosphate rock is currently mined, the environmental problems presented by mining and processing the rock, and some mitigating technologies being employed to answer such problems. THE PHOSPHATE DEPOSIT AND ITS EXTRACTION Florida's phosphate deposits containing the calcium phosphate mineral, carbonate-fluorapatite, are between ten and fifteen million years old. The typical "bone valley" matrix is 15 feet thick and lies under 20 to 30 feet of overburden.(Fig. 1) Both the sandy overburden and matrix are unconsolidated and can be removed with standard 45 to 65 cubic yard, walking electric draglines. After removing the overburden, which is windrowed nearby, the dragline operator casts the matrix into a "slurry" pit where it is broken up by high pressure water monitors. Pit pumps (with boosters where necessary) transport the matrix slurry through 16 to 20 inch pipelines to a washer where the three components of the matrix (sand, clay and apatite) are separated. The phosphates contained in central Florida matrix are approximately half pebble/half flotation feed, through the pebble ratio decreases as the industry mines southward. Again, the matrix is roughly equally divided among sand, clays and apatite. The phosphatic clays, 75% of which are less than one micron in size, leave the washer as a 3 to 5% colloidal suspension. The impoundment of these waste clays is one of the environmental challenges to be discussed later. The sand (silica) is separated from the similarly sized phosphate particles by a double float process (fatty acid followed by a reverse mine or cleaner float), and the sand tailings are then pumped to disposal or reclamation sites. The apatite flotation product is combined with the screened phosphate pebbles and stacked to dewater before shipping.

Jan 1, 1992

By Stanley O. Reichert

At nuclear facilities, three types of radioactive waste must be managed: (1) high-level liquid waste containing fission products from the chemical separation of irradiated uranium, (2) low-level condensates from the concentration of the high-level waste, and (3) dry solids such as obsolete process equipment, spent ion exchange resins, and irradiated metal scrap. The geological and environmental characteristics of a site are important considerations in planning the waste management program. At the Savannah River Plant, low-level liquids and dry solids are safely and economically placed in the soil where the geologic and hydrologic conditions are favorable. Within the general area where the waste originates, studies are made to locate seepage basins and burial grounds in the most favorable sites: (1) soils should have a high ion exchange capacity and moderate to low permeability, (2) the water table should be deep, and (3) burial sites should be relatively distant from the nearest flowing stream.

Jan 1, 1968

By W. G. Kegel

Coal mining today is confronted with numerous problems, all of which affect in some way the ability of the operator to produce profitably. The major endeavor, therefore, is a quest for cost lowering techniques. Complete belt haulage from shuttle car to river barge appeared to be a step in such a direction. A deep look into all aspects proved this to be more involved than just the installation of such a belt line. With this paper, we will attempt to present to you the problems and requirements of design and installation of an all-belt haulage system, believed to be the longest underground belt installation in the world at this time. The first and most important item is the justification of an all-belt haulage system. The following is a brief history of the coal property and the facts affecting our decision.

Jan 1, 1964

By Yadong Xue, Fei Wang, Hongwei Huang, Yan Sun

"Increasing attention to subway tunnel maintenance is being paid with the high speed development of urban rail transit system in China. A novel moving tunnel inspection equipment based on machine vision is developed in this paper. High resolution image acquisition system is proposed for tunnel crack and leakage inspection. The main components of this image acquisition system includes high speed CCD cameras, linear lights and high performance computer. To inspect the crack less than 0.3mm with a 3-5km/h speed in subway tunnel, we need to consider resolution and line rate of camera, pixels of cameras, range of inspection and illumination intensity of lights simultaneously. The optimization design is proposed to make the equipment more convenient for tunnel use. Entire tunnel situation can be detected and recorded in a single inspection process. This equipment has already been verified in Shanghai subway tunnel for defects inspection.1. INTRODUCTION In China, the quantity of subway tunnel has reached a large scale in recent years. Until 2014, there had been more than 2300km of subway tunnel in China which accounted for nearly three quarters of Chinese urban railway system (Zhang Chen,2015). In some metropolises like Beijing and Shanghai, most of the metro tunnels has already run over 20 years which within maintenance phase. This has brought about plenty of inspection work and maintenance work to guarantee the tunnel under the serviceability limit states. The increase of running mileage of subway tunnels in China has been displayed in Fig 1."

Jan 1, 2016

By B. H. Kim, P. Zhang, M. A. Van Dyke, D. Su, H. Dougherty

The National Institute for Occupational Safety and Health (NIOSH) has been evaluating longwall mining-induced strata fractures and their impacts on casing stability of Marcellus shale gas wells located in longwall pillars. To understand the extent of overburden fractures after longwall mining, NIOSH researchers drilled a postmining corehole into the fractured strata above the Pittsburgh coal seam longwall gob. Knowing the extent of the fracture zone height will help gas operators minimize the hazards of drilling into longwall gobs. The core was retrieved from the surface down to the top of the gob void. Various fractures were encountered varying from 35 to 64 degrees, depending on lithologic type and relative closeness to the gob. The longwall panel dimension was 457 m wide and 3657 m long, in which the total fracture zone height was found to be at 141 m and the hydraulic connected fracture zone at 87.7 m above the top of the Pittsburgh seam. In addition to core drilling through the gob, FLAC3D modeling was also used to simulate the formation of fracture zone and the orientations of longwall-induced fractures. This study provides much-needed evidence on the fracture zone of Pittsburgh seam longwall gobs to help gas operators avoid potential hazards associated with drilling through highly fractured zones

Mar 2, 2022

By J. W. Cooksley

Seismic methods provide an efficient and comprehensive approach to overburden studies pertinent to mining exploration and development, and to other mining and civil engineering problems such as rock mechanics, slope stability, and foundation engineering. For the purpose of defining geologic units and structural features, these methods are generally regarded as the most accurate, but most expensive, of the commonly-used geophysical exploration methods. Although the accuracy and cost of seismic work are generally affected adversely by rugged topography and complicated geologic conditions, it is in rough terrain and complex geology that seismic methods offer important advantages in overburden investigations. For example, to find the surface of rock underlying unconsolidated overburden at depths of approximately 200 feet, a 50-foot spacing of drill holes along the profile line would be required to yield a degree of resolution and accuracy similar to that obtained from a 50-foot spacing between seismic detectors along the same line. See Figure 1. In cases similar to that shown in Figure 1, a twelve-channel recording seismic system would be used. The main components of such a system would be: 1. detectors (commonly referred to as geophones) which convert the ground movement resulting from seismic waves into an electrical signal. 2. a multi-conductor cable which connects the seismic detectors to the amplifiers. 3. ampliiiers, amplify and filter the electrical signals . 4. oscillograph, records the amplified signal. 5. the blaster and firing line. A typical layout of the seismic spread and the components of the system Is shown in Figure 2.

Jan 1, 1968

By J. K. Brooke

Fluorine is a lively element in both its chemical and economic behavior. It was not isolated as an element until 1886 by Moissan. However, its principal source to this day, fluorspar, was known and its special merits recognized long before that time. Our own mining brother, Agricola, is credited with having named fluorite, the mineral name, in 1546 from the Latin, "fluere", to flow. It made things melt and was already being used as a flux. Because fluorspar has been found as a relatively common gangue mineral in metal ore veins, it has long attracted the attention of geological thinkers seeking to, explain the whys and wherefores of veins. Fluorine has been thought of as one of the principal mineralizers, holding metals in ascending vein solutions for deposition close enough to the eventual surface to be accessible for profitable mining.

Jan 1, 1964

By W. E. Lytle

Environmental permitting is a critical component for joint-venture projects located in the Commonwealth of Independent States (CIS). This paper presents the basic CIS regulatory environmental requirements for permitting of a hypothetical mining source and emphasizes air permitting. Topics which will be covered include: the Expertiza process, air pollution quantification, data requirements, and air pollution modeling protocol. A comparison will be made between permitting requirements for air pollution sources in the United States and a CIS country, Kazakstan.

Jan 1, 1998

By Peter M. Fozzard

A review is made of the actual costs of recent foreign mineral exploration programmes in third world countries. Target identification leading to the selection of areas, or macro-targets, must follow a well planned and defined series of steps. Suggestions are made with respect to this inter-active project development work. Potential revenues in the broad sense will always determine the overall economics of exploration but clear objective philosophy, good planning and adequate financing are essential for exploration success. Considerable opportunities exist for making important foreign mineral discoveries and broad selected suggestions are made for the identification of exploration areas in relation to high-grade and precious metal mineralization.

Jan 1, 1984

By J. Lorosch

Improvement of current leaching technology was found necessary when processing ores which are more difficult to leach because they generate highly viscous, air-rejective pulps. Cyanidation of these pulps has to run at low oxygen concentrations if the conventional aeration technique with compressed air is used. Since the dissolution rate of precious metals mainly depends on the concentration of dissolved oxygen in the pulp [1, 4, 5], the kinetics of the gold extraction become slow in such cases, which in turn often leads to a significant decrease in the overall gold output within the conventional leaching time of up to 48 hours.

Jan 1, 1988

By D. G., Bosse&apos

Equipment choices for ultrafine grinding encompass several different types of dry and wet size-reduction devices. These need to be put into functional perspective for systematic analysis of capabilities and limitations versus processing requirements of the materials to be satisfactorily ground. Particle strengths plus maximum and average sizes are the primary variables controlling grinding action requirements and equipment options for efficient processing. These are fairly well understood and provide the starting point for decisions. Particle space requirements under dynamic processing conditions vary with particle shapes and size-distributions by as much as 30X. This additional major variable is not widely appreciated and does need adequate description to provide a firm basis for selecting processing compositions and procedures.

Jan 1, 1983

By D. R. Spears

The Bureau of Mines has investigated the fundamental aspects of shear-flocculation using a rapid, in-situ particle size analyzer. Silica was stirred in the presence of an aliphatic amine to determine the effects of collector coverage, stirring speed, and solids concentration on the kinetics of shear-flocculation. The results showed that shear-flocculation is a two-stage process. In the first stage, mean particle size increased rapidly in the first 1-2 min of reaction; in the second stage, an equilibrium was set up between the rate of floc growth and floc decay. Collector dosage affected the position of the equilibrium by altering the number of surface sites for particle-particle attachment. A minimum stirring speed was necessary for shear-flocculation to occur and was dependent on solids concentration and collector dosage. This speed was the minimum necessary for particles to overcome the electrostatic energy barrier which kept conditioned particles dispersed. Larger particles flocculated more rapidly. At very high stirring speeds, large flocs became unstable, resulting in a narrowed particle size distribution in the slurry.

Jan 1, 1993

By D. G. Kotlyar

Silver is an economically important component of many complex, massive sulfide ores. Current beneficiation for these ores is almost entirely by flotation. Silver recovery often is low, but little is known about the flotation behavior of the silver-bearing minerals. Floatability studies were conducted using silver-bearing tetrahedrite and lead-zinc ore. The effects of xanthate collector concentration, conditioning time, potentiostatic control of the mineral potential, and pH on mineral floatability were evaluated. The floatability of the silver-bearing minerals was shown to depend on collector concentration and mineral potential. The effect of controlling mineral potential during the flotation process is discussed.

Jan 1, 1994

By William P. Walsh

In December 1983 the author undertook an investigation in east Texas which was organized to learn the feasibility of applying geophysical techniques over shallow lignite deposits. The work embraced experimental high resolution seismic reflection and offset Wenner resisitivity sounds over three 1/4 to 1/2 mile test sections. This site also was sponsored by Woodward-Clyde Consultants (WCC) and a consortium headed by North American Coal Corporation. The principal objective of this investigation was to learn whether the aforementioned geophysical techniques could be applied over shallow lignite deposits (i.e. located at approximately 100' to 300' in depth) and consequently provide structural and stratigraphic information useful for resource and reserve characterization. A secondary objective was to determine if these same techniques could disclose the nature of the overburden and the distribution of ground water therein.

Jan 1, 1986

By R. C. Gilmore, A. Juganda, Jr. Bogin, S. Saki, S. A. Lolon, J. F. Brune, Jr. Zipf, J. W. Grubb

"Methane-air mixtures form explosive gas zones (EGZs) in underground longwall coal mine gob ventilation systems. Such EGZs have caused a number of fatal mine explosions, including the 2010 disaster at the Upper Big Branch mine, where 29 miners lost their lives. Researchers at the Colorado School of Mines use Computational Fluid Dynamics (CFD) modeling to predict EGZ locations. In this paper, a model of a bleeder-ventilated gob system includes two adjacent panels, an active longwall and a mined-out gob. Boundary conditions for the simulations match statutory ventilation conditions for methane concentrations and air flow rates at common measurement points throughout the mine. The modeling results predict the persistence of EGZs in the gob that may compromise the effectiveness of the bleeder ventilation system. INTRODUCTION Mine operators must maintain statutory air flow and air quality requirements at various locations throughout the mine ventilation network. U.S. regulations generally require mine operators to establish bleeder ventilation systems surrounding longwall gob areas (30 CFR §75.334.) Gilmore et al. (2015) documented that explosive gas zones (EGZs) exist within bleeder-ventilated gobs and may extend into the bleeder entries that must be examined weekly, presenting an immediate fire and explosion hazard to mine examiners. In a project funded by the National Institute for Occupational Safety and Health (NIOSH) under contract 200-2009-31409, researchers at Colorado School of Mines have developed a tool for modeling gob air quality using Computational Fluid Dynamics (CFD). This CFD model is capable of examining a wide range of longwall mine ventilation systems. Marts et al. (2014a, 2015) studied progressively sealed gobs with U-type ventilation and using a back return. Saki et al. (2015) examined the impact of gob ventilation boreholes and face air quantity effects on tailgate methane concentrations. Gilmore et al. (2014) modeled bleeder-ventilated gobs and Gilmore et al. (2015) studied the effects of bleeder regulator settings on EGZ volume and locations in the gob. CFD studies for progressively sealed gobs were generally carried out using 5000 ft (1500 m) panels because the gob atmosphere remains largely unchanged from about 500 m (1,500 ft) inby the face. A modular meshing methodology (Gilmore, 2015) permitted researchers to extend bleeder models to 10,000 ft (3050 m) to include the full extent of bleeder entries. This paper further expands the bleeder CFD model to study the gob atmospheres of two adjacent longwall panels, each 10,200 ft (3100 m) in length, with the active face located 6,700 ft (2040 m) from the startup room."

Jan 1, 2016

By John W. Lane

Climax Molybdenum Company, a Division of American Metals Climax, Inc., operated a hydrometallurgical plant* at Climax, Colorado from August 1966 through August 1968 to recover molybdenum from a mixed oxide and sulfide ore. The ore treated for this addition to the existing plant contained sufficient Molybdenite values to be mined for Molybdenite recovery alone, so that the oxidized molybdenum recovery could be regarded as a byproduct operation. Climax is located at an elevation of 11,300 feet. All process equipment, except thickeners, was enclosed in buildings. Annual snowfall is approximately 250 inches per year. Paved highways and rail service to the plant are maintained and kept open all year. Most of the employees live in the town of Leadville, which is approximately twelve miles from the plant site. The sulfide flotation plant handles 40,000 to 45,000 tons per day of ore. The mine is one of the world's largest underground mines.

Jan 1, 1971

Sphalerite is commonly floated in an alkaline environment and under such conditions the overall activation mechanism is obscured by the hydrolysis of Cu2+ and precipitation of Cu(OH)2. Electrokinetic and kinetic flotation tests show that the activation of sphalerite is a two-stage process; the activation products formed on the surface of sphalerite in near neutral and in alkaline solutions in the first rapid activation stage are "flotation-inactive". These layers, when formed in an alkaline solution, are unstable and are transformed into the "flotation-active" form in the second stage. However, the surface layers formed during activation in alkaline environment by copper in the presence of lead ions are very stable and even after a long conditioning time the flotation rate is not improved. Consequently, while both Cu2+ and Pb2+ activate sphalerite flotation, quite unpredictable effects may result when both are present in the solution.

Jan 1, 1997

By Eric R. Braun

Ore reserves in the Republic mining district were nearly exhausted in 1984 when hole D-54 intersected a vein twenty- eight feet in drill width averaging 1.57 opt gold and 11.95 opt silver below post-mineral lake beds. The discovery area, termed "Golden Promise", has announced proven and probable ore reserves of approximately 372,000 tons averaging 1.0 opt gold and 4.5 opt silver, and drilling indicates another 756,000 tons of mineralized material containing 0.37 opt gold and 1.4 opt silver (Hecla fourth quarter 1986 report). This paper describes new geological interpretations made as part of a district research study sponsored by Hecla Mining Co., which led to the D-54 discovery. Important new geological concepts include: 1) re-interpretation of the volcanic stratigraphy of the district and recognition of a suite of pyroclastic rocks that are unique to the Republic graben, 2) identification of disseminated subaerial mineralization at a paleosurface that corresponds to the newly described upper contact of the Sanpoil Volcanics, 3) recognition that epithermal veins have a maximum productive vertical range of 0-500 meters, measured from the paleosurface, and 4) veins exhibit visual and geochemical vertical zoning within the productive zone with highest gold occurring at an optimal depth, which is interpreted as the average depth of hydrothermal boiling.

Jan 1, 1987

By A. K. Basu

Rapid industrial growth in India has caused the country to realize the strategic importance of its zinc and lead deposits. Private companies, nationalized in 1965, are now a corporate public sector organization that is making great strides in developing the nation's lead-zinc mining capability. The main mining area is centered around Zawar at Rajasthan. It consists a group of mines - Mochia, Balaria, Zawarmala and Baroi. Mining activities have also been extended by opening the mines at Rajpura-Dariba at Rajasthan, Sargipallie at Orissa and Agnigundala at Andhra Pradesh. A huge deposit has been explored at Agucha in the Bhilwara district but full-scale production has not yet begun. Annual consumption of zinc and lead in India has risen steadily from 25 and 7.9 kt (27,500 and 8700 st), respectively, in 1973-1974 to 162.8 and 80 kt (179,450 and 88,000 st), respectively, in 1989-1990. Mine production has also risen consistently to cope with the increased metal demand. The mining company hopes to increase production at existing mines and upgrade the beneficiation and smelting facilities. Moreover, mining operations may be expanded by opening up new units that are now awaiting governmental clearances. Technology status Mining technology has undergone a rapid, large-scale transformation, with an accelerated pace of new, larger capacity mine development. Notable advances include the introduction of mechanized ore extraction methods and

Jan 1, 1991

By A. V. Castelli

Weighting materials as we know them today were first recognized in 1922 by B. K. Stroud1. Stroud, who was supervisor or the Mineral Division of the Louisiana Department of Conservation, tested galena, cement and hematite as weighting materials and successfully used hematite to make a "heavy mud". The first use of barite was in the fall of 19222 . The process of adding heavy minerals in mud was patented in 1926 by Stroud and National Pigments and Chemical Company, a subsidiary of National Lead Company now NL Industries, Inc. The ground barite was marketed as BAROIDR barite.

Jan 1, 1983