Search Documents

By Pierre Dosmond

In ore mining technology, the loading and hauling operations are undoubtedly the area where the most spectacular progress has been made during the last twenty years. I shall draw some examples from the Eastern France iron ore mines which I how well and whose production of 62 million tons for 1962 and 1963 constitute a worthwhile experience worldwide. The iron ore deposits of Lorraine are of sedimentary origin. They contain many mineralized horizons with workable seams situated from 330 to 830 ft. in depth. The dip of these seams is generally less than six percent. Their thickness varies from 6 to 23 ft. All seams are not workable throughout the whole area of occurrence, but in some mines there are five mineable seams in the same vertical section, with from 5 to 20 ft. of barren ground intervening between them. The iron content of the mineral varies from 28 to 36 percent. Specific gravity of the ore is 156 lb. per cu. ft. m place and 100 lb. per cu. ft. blasted. Reserves of iron ore in the Lorraine region are estimated at six billion tons with an iron content of more than 28 percent. These mines operate by means of rooms and pillars process, with pillar robbing; the final recovery is very good and averages 90 percent. Some years back, competition from richer, imported ores incited these mines to make constant efforts to increase their productivity and reduce mining costs, thus placing them in a leading position in mining technology, as evidenced by the dramatic evolution of their output per manshift (Figure No. 1).

Jan 1, 1970

By P. A. Meyer

The Tenmile Range is a north trending zone of high relief within the central Colorado porphyry-mineral belt, located between Leadville and Breckenridge. (Figure 1, the Index Map of the area surveyed.) The Climax mineralized zone is located at the southern end of the range on the northwest side of the Continental Divide. This portion of the total area surveyed will be discussed in detail today. A fixed wing aeromagnetic survey was flown over this range and mineralized zone in the fall of 1957. The survey was run as an experiment to see if a useful geophysical tool could be applied in the exploration for similar type deposits. The purpose of this paper is to describe the results of this survey and the approaches used to aid in the interpretation of the total intensity data.

Jan 1, 1968

By Jorgen Elbrond

Before and in the early stages of industrialization, mining was the undisputed leader in technology. It represented the high-tech of the time. Early mechanization bears witness to that. Hoisting and rock breaking driven by waterpower are such examples. The mines' use of the steam engine was a major incentive to its development. By these means new mines could be opened and more metal supplied. Understanding of systems was essential for miners when shaping the infrastructure of the mines for the transportation of ore, material and men and for the evacuation of water and for ventilation. The irrigation systems of ancient mines are such examples. However, with the industrial revolution other more specialized branches of industry advanced further, and the mines became users of other industrial branches technologies. The mining industry had, however, always been quick to recognize a good thing and use it, when time was right. But, compared with other branches of industry, the mining industry has the disadvantage of working in a rugged environment with (and actually inside) a raw material which is abrasive and highly variable with respect to mechanical properties. This determines the rather high unpredictability of mining machines' performances and their low availabilities and explains a part of the delays in introducing technological advances.

Jan 1, 1989

By William Petruk

Lithium bearing lepidolites from three deposits in the province of Goias in Brazil were investigated to determine whether there is a correlation between the lithium content of the mineral and the colour of lepidolite and associated tourmaline. Such a correlation can be a useful guide to field geologists for outlining high grade ore zones. It was found that mauve-pink lepidolite associated with pink tourmaline, and brownish lepidolite associated with black tourmaline have high lithium contents, but the colour of lepidolite is not due to lithium. The pink colour of lepidolite and tourmaline is likely to Mn3+, and the brownish tint of lepidolite and black colour of tourmaline to Fe3+. Lepido lites appear to be lithium-rich when the lepidolite and associated tourmaline contain relatively high amounts of Mn3+ and/or-Fe3+.

Jan 1, 1985

By Derek M. Hutchinson, Don Zeni

The construction of shafts by blind drilling has been made cost effective by advances in technology and experience. The techniques of blind shaft drilling are discussed and a brief history presented. A recent use of blind shaft drilling to access a small gold ore body in Australia is described. Finally, the most recent developments in drilling machinery are reviewed together with possible applications in new and existing mines.

Jan 1, 1987

By E. Scott Bair

Renewed interest in the vast reserves of anthracite coal in eastern Pennsylvania led to the use of a numerical model for simulating the hydrologic effects of constructing an open-pit anthracite mine. The proposed mine would be approximately 1800-m (5900-ft) long, 1000-m (3300-ft) wide, and 300-m (1000-ft) deep. A two-dimensional, finite-difference, ground-water flow model was used to calculate ground-water seepage rates into the proposed mine, to evaluate the effectiveness of various deep-well dewatering systems, to calculate drawdown in adjacent wells and properties, and to estimate the capacity of the water-treatment plant. Site-specific values of pertinent hydrogeologic parameters were used in the simulations.

Jan 1, 1980

By R. W. Ballmer

Bingham Canyon lies in the heart of the Oquirrh Mountains, 25 miles southwest of Salt Lake City, Utah. In it is located the world's largest open-pit copper mine, owned and operated by the Utah Copper Division of Kennecott Copper Corporation. From the beginning of open pit mining operations in 1906 until 1963, the pit haulage, or materials transportation, was primarily by rail. In 1963, phase-in of a truck haulage system in the upper two-thirds of the pit was begun. The details of that conversion, its associated problems and the resulting pit operation have been covered in an earlier paper.1 The purpose of this paper is to discuss various factors for consideration in transportation system selection, and to discuss some of the alternatives considered prior to making the change from rail haulage to truck haulage for a portion of Bingham Canyon.

Jan 1, 1968

By P. Berendsen

Structures along the rift were subjected to episodic reactivation. Major north-northeast-trending high-angle normal or reverse faults and northwest-trending trans-current fault systems, may exercise control over ore-forming processes. Gabbro and basalt are the dominant igneous rock types. Carbonatite and kimberlite occur in Nebraska and Kansas. Concentrations of Cu, Ni, Co, Ti, Au, Ag and PG-minerals are known to occur in this setting Arkosic sandstone, siltstone, shale and minor carbonate units occur on top of the rift basalts and in flanking basins where they may reach thicknesses of 10 km. The potential for stratiform or unconformity-related metal liferous deposits must be considered.

Jan 1, 1986

By Grant Davis

An International Symposium on the Ecology and Revegetation of Drastically Disturbed Areas was held at the Pennsylvania State University in August 1969. Scientists from 13 foreign countries and 18 states in the United States attended this meeting, which focused on those areas disturbed by mining. The symposium enabled scientists from all over the world to get together for two weeks and discuss informally some of the knotty problems of reclaiming these disturbed areas. Trying to present the results of each of the 64 papers delivered at the symposium might be difficult. So, I will try to bring you up to date on the general status of research on the reclamation of surface-mined areas, particularly in revegetation and hydrology. I will also mention some research that is under way but was not presented at the symposium.

Jan 1, 1970

By S. E. Knalafalla

The availability of a fluid whose gross behavior sharply changes in a magnetic field without affecting its rheologic characteristics has been recently demonstrated. A colloidal solution of a ferrimagnetic material, such as magnetite, in a liquid that is immiscible with and lighter than water is projected for use in selective separation of particles according to their density spectrum in a continuous fashion. Magnetic levitation forces were created as an antigravity field when the fluid was properly placed in an inhomogeneous magnetic field. Five spherical non¬magnetic objects with densities ranging from 2.70 to 11.35 gram cm ' were made to float or submerge at will in a 0.96-gram cm-3 density fluid placed at vertical magnetic field gradients ranging from 0.2 to I kilooersted cm-1. The magnetic levitation farce in dyne cm-3 was found to vary linearly as a function of the object-fluid density mismatch with a slope equal to one g, the acceleration due to gravity.

Jan 1, 1972

By W Frint

An area in Southwestern Wyoming is rapidly becoming the soda ash capitol of the world. Starting only 20 years ago from a unique deposit of trona, the out-put has rapidly increased until now about half of the soda ash produced in the United States comes from this area. Chemically, soda ash is sodium carbonate, a large tonnage, widely used alkali. The largest single industrial use is in glass manufacture, where 25 tons of soda ash are used in producing 100 tons of glass. Other big users are the detergent and chemical industries. The trona deposits in the Green River basin of Wyoming, were formed about 75 million years ago as part of a geologic period when an ancient lake alternately went through periods of being a large fresh water or smaller brine lake. Today these deposits lie from 800 to 3000 feet below the surface in a semi-arid, almost desert region just west of the Rocky Mountain Continental Divide at an elevation of 6200 feet. In this area there is a prevailing westerly breeze and almost every afternoon the velocity reaches very windy conditions. Rainfall is minimal, being only 6-8 inches of moisture per year with an evaporation rate exceeding 24-inches. Most of the moisture comes in winter snows or summer thunderstorms. Temperatures are low with below zero weather dur¬ing most of the winter and early morning frost is not uncommon during the summer months. There are many trona beds varying in thickness from a few inches up to 15 feet. The deposits now being mined vary from 8 to 10 feet in thickness. The ore is mined by driving tunnels either via conventional explosives or with continuous boring machines. It is transported to the shafts via conveyor belts

Jan 1, 1972

By Richard W. Patton

With the advent of the Clean Air Act and the installation of flue gas desulfurization (FGD) equipment (scrubbers) on coal fired power plants, the management of solid wastes has taken on added importance. Aside from the large amounts of fly ash and bottom ash usually generated, large quantities of liquids in the form of scrubber sludge are also produced. These wastes must be disposed of within the constraints of land and water quality regulations. This paper describes the practices adopted by the electric utility industry in denting with this problem, including methods of generation and treatment, quantities and characteristics of the materials, and transportation and disposal practices. The paper also briefly describes final product characteristics and several applications for commercial utilization and land reclamation.

Jan 1, 1983

By Michael M. Donahue

"The public interest -- as opposed to the narrow interests of particular shippers -- will also benefit from the establishment of adequate revenue levels and the revitalization of the railroads. And this is particularly true with respect to the transportation of coal. "

Jan 1, 1981

By J. Groppo, W. Zhang, R. Honaker

"Rare earth elements (REEs) found in coal are in the form of minerals, ion-adsorbed onto clay surfaces or inner layers, or organically bound. Rare earth minerals such as monazite exist in coal and have grain sizes smaller than 5 µm. In this study, froth flotation was successful in concentrating rare earth minerals existing in a thickener underflow material derived from Fire Clay seam coal that contained around 431 ppm of total rare earth elements (TREE) on a dry ash basis. Conditioning with fatty acid followed by processing using multiple stages of conventional flotation produced a final concentrate containing 2,300 ppm TREE. Using a laboratory flotation column to limit hydraulic entrainment, the TREE content was further enriched to around 4,700 ppm, which equated to an enrichment ratio of 10:1.IntroductionRare earth elements (REEs) are becoming increasingly important and have been widely used as raw materials for the production of phosphor, metal catalysts, magnets and batteries (Binnemans et al., 2013; Zhang et al., 2015). REE recovery from alternative sources such as coal and coal byproducts has the potential to stabilize the economic viability of coal mining operations while providing a dependable supply of critical materials.The average REE content of the world’s coal resources is around 60 to 70 ppm (Zhang et al., 2015). There are many well-known coal beds with high contents of REEs such as those in the Far East coalfields in Russia with contents of 300 to 1,000 ppm, the Fire Clay coal seam in eastern Kentucky in the United States with contents around 500 ppm and the Sydney Basin in Nova Scotia, Canada, with contents of 72 to 483 ppm (Birk and White, 1991; Seredin, 1996; Hower, Ruppert and Eble, 1999; Blissett, Smalley and Rowson, 2014). The occurrence of REEs in coal and coal byproducts can be classified into three types: (1) rare earth minerals, such as monazite and xenotime, (2) ion-adsorbed REEs on clays and (3) REEs associated with organic matrices. The rare earth minerals in coal and coal byproducts are very small in particle size, generally on the micrometer and/or nanometer scales (Honaker et al., 2014). Froth flotation, which concentrates minerals based on surface chemistry differences, has been widely used to treat fine rare earth industrial minerals such as monazite, xenotime and bastnaesite (Abeidu, 1972; Cheng, Holtham and Tran, 1993; Pavez and Peres, 1994; Pavez, Brandao and Peres, 1996; Jordens et al., 2014). As such, flotation is a promising method for the concentration of rare earth minerals from coal and coal byproducts."

Jan 1, 2017

By John E. Litz

Since the 1974 introduction of catalytic converters to automobiles in the United States, more than 150,000 kg (5,000,000 oz) of platinum, palladium, and rhodium have been used in the converters. An estimated 8 to 10 million converters are being used annually in the United States, each containing from $5 to $15 of PGM metals. In addition, use of converters is beginning in Europe which will significantly increase the quantity of PGM used. Two basic types of catalysts for converters are being used: pellet and monolithic. The pellets are small, discrete spheres or cylinders of gamma-alumina coated with platinum group metals, Figure 1. The monolithic are honeycombs of a cordierite, A13(Mg,Fe)2Si5AlO18, base coated with gamma-alumina and subsequently with platinum group metals, Figure 2. Pellet catalysts are being used by General Motors and American Motors; whereas Ford and Chrysler are using monolithic catalysts. The table below compares the PGM content and value of the catalysts.

Jan 1, 1986

By F. Seymour

A dynamic programming algorithm is presented that takes a series of nested phases, a fixed mining rate schedule, a fixed plant production capacity schedule, and finds the mining and cutoff grade sequence that maximizes the Net Present Value. This tool allows the Mining Engineer to quickly look at project sensitivity to various production capacities, commodity prices, and costs. A description of the algorithm is given along with examples of how it has been used at Newmont.

Jan 1, 1995

By T. W. Lloyd

Accurately predicting coal seam discontinuities is an important part of modern underground coal mining. Conventional methods of coal exploration sometimes fail to identify rapid variations that may seriously impact mining and quality. Radio Imaging Method (RIM), a geophysical approach to mapping longwall panels, has been developed where electromagnetic signals are transmitted and received though the coal block. The amount of signal loss for a given distance, when compared to the coal seam characteristics, identifies anomalous areas. A comparison of RIM predictions with actual geologic conditions encountered during longwall mining demonstrates the accuracy and usefulness of the data.

Jan 1, 1986

By Stephen E. Kesler

Carbonaceous sedimentary rocks are abundant in the upper part of the caldera or maar that hosts the Puebio Viejo Au-Ag district, and much of the Moore sulfide zone is in these rocks. These rocks are thinly layered and contain scattered plant remains and variable amounts of volcaniclastic debris and pyrite. The carbonaceous matter in the sediments yields no X-ray diffraction pattern and is not graphite. It has C/N ratios of 4 to 10, and &13C values of about -25 per mil, which indicate that it is dominantly of marine organic origin and partly degraded. Atomic S/C ratios in the unmineralized part of the carbonaceous rocks have a median of about 1.2, much higher than most similar unmineralized rocks, reflecting not only the abundance of pyrite in the sediments, but also the fact that the organic material contains several percent sulfur. Extracts from the organic material indicate that it is thermally mature and that it reacted with the hydrothermal solutions. Atomic S/C ratios in the mineralized carbonaceous rocks are generally higher than those in unmineralized carbonaceous rocks, ranging to values of 5 and more. These differences indicate that significant amounts of carbon were consumed by the reduction of sulfate and metal chloride complexes in the mineralizing fluids as they passed through the carbonaceous sediments. Direct reaction between organic material and ferrous chloride-bearing, acid-sulfate hydrothermal solutions probably caused continuous deposition of pyrite during this period. Intermittent deposition of gold from chloride complexes by the same reaction was probably facilitated by boiling or C02 effervescence.

Jan 1, 2013

By L. M. Turner

Perlite is a unique mineral that upon heating expands to about twenty times its original volume. Mining is by open pit method. The processing cycle involves crushing, screening and sizing the ore. An on-site quality control facility at the Manville Products No Agua mine exerts a high degree of control over every phase of the operation from blasting to finished product.

Jan 1, 1985

By Robert L. Stroup

Let me open my remarks this morning by stating how we as legislators and as natives of the western coal-producing states feel about our role in becoming one of the major producers of coal-related energy and chemical products is similar to the groom at his shotgun wedding. We are apprehensive, to say the least, as to the ultimate outcome. We do not have complete freedom of choice. It will certainly change our quality of life. We are concerned about the increase in population, but are realistic enough to recognize that we are forced to go through with the marriage. Other alternatives could be worse than the bride. Also, we were aware that this could occur, but we did not plan on it being this sudden. Or, put another way, we have two groups advising us that our choices are cattle or coal, food or fuel, pollution and people or pure air, wheat or gas, clean water or prosperity, noise or solitude.

Jan 1, 1976