Search Documents

By H. Saridikmen, C. S. Kucukkaragoz

In the present study, the measurement of sulphur distribution ratios between the slag and metal phases encountered in the ferromanganese smelting has been carried out at 0.83 atm of partial pressure of CO at 1773 K by using classical gas-slag-metal equilibrium quenching technique as a function of composition. The distribution results were employed in calculating the sulphide capacities of SiO2-Al2O3-CaO-MgO-MnO slags in equilibrium with the Mn-Fe-Si-Csatd.-S metal phase. It is shown that the sulphur transfer from metal to slag phase increases with increasing the basicity of the slag. As expected, the sulphur distribution ratio decreases by increasing the silica content of the slag system. The effect of metal composition on the sulphide capacities of the slag as well as on the sulphur distribution ratios between the slag and metal phases have been discussed. Emprical relationships were developed to express the sulphur distribution ratios and sulphide capacities of the above slag system.

Jan 1, 2007

By S. O. Bada

Fine phosphate feed is considered to be slime and normally disposed of as a discard in settling ponds or dumped as landfill. The purpose of this research was to establish whether commercially acceptable qualities and yields could be obtained from this material using dry separation methods. The results obtained from the electrostatic separation of <105 µm phosphate ore are presented. An existing separator was upgraded in order to improve on product and flotation concentrate recovery, to test different mineral, and to reduce particle residence time between the charging chamber and the separating zone of the separator. The operating conditions were varied according to the charges imparted to the particles in the electric field, and according to other device parameters. Parameters such as splitter position, charge reversal, rotation speed, charging voltage and separating voltage. The <105 µm phosphate feed was concentrated under both triboelectrification and inductive charging. The use of inductive charging and charge reversal resulted in a significant increase in grade for <105 µm phosphate feed, with the P205 grade increasing from about 12 per cent to 20.50 per cent, and a recovery of 26.30 per cent under a single stage of separation. It was found that better separation was achieved at rotation speed of 6000 r/min, -8 kV charging voltage, and 25 kV separating voltage.

Jan 1, 2012

Professor H.R. Philips was born in South Wales. After graduating with a B.Sc. degree in electrical engineering from the University of Bristol, he joined the National Coal Board&apos;s management training programme. Mr B. Moore was born in Coventry, England. He matriculated at Bablake School and then atended Birmingham University, obtaining a B.Sc. Mining Engineering degree in 1953. Professor J .S.J. (J annie) van Deventer matriculated at Swelendam High School. He studied chemical engineering at the University of Stelenbosch, and obtained the degrees of Hons. B. Ing. in 1978 and Ph.D. (Ing.) in 1985. Professor M.D. Brayshaw received most of his education in England but obtained his Ph.D. (Eng.) at the University of Natal. Rock fragmentation by blasting The Third International Symposium of Rock Fragmentation by Blasting will be held in Brisbane, Australia, from 26th to 31st August, 1990. The Third International Symposium of Rock Fragmentation by Blasting is designed to inform delegates on the state of the art in explosives and blasting technology, and to build on the standards of excellence set by the previous symposia in Lulea, Sweden (1983) and Keystone, Colorado (1987). Delegates with an operational, technical, or research focus on blasting will gain from this interactive symposium. Recent journal Mineral resources engineering, edited by C. T. Shaw, T.L. Car, and M. Karmis. London, Taylor & Francis, 1989. Published quarterly. US $107 per year. Risk management The Cost Engineering Association of Southern Africa (CEASA) is to hold its 3rd Biennial Symposium at Indaba, Midrand, on 25th and 26th January 1990. The title of the Symposium is Risk Management in Promotion of Capital Projects. The present political and economic environment in South Africa is characterized by a lack of financial resources, and of technical and management skills, on the part of project owners, designers, and contractors/ vendors.

Jan 1, 1989

By M. Nduna

Surface properties of metal sulphides have a great significance in various areas of engineering and science, such as acid mine drainage, contaminant sorption, and metal separation. In various attempts at producing metal sulphide particles from synthetic solutions, prodigious quantities of nuclei that grow only to colloidal dimensions have been frequently reported. This copious nucleation is promoted by the high levels of supersaturation that characterize most precipitation reactions. Colloidal particle formation in precipi¬tation-based separation processes results in sub-optimal solid-liquid separation, which is alleviated by the production of more highly crystalline particles or agglomerates. The current work approaches this challenge from an electrochemistry perspective, by measuring surface charge potential of precipitant particles during metal sulphide precipitation with respect to the concentration of metal sulphide lattice ions in solution. Electrophoresis was used to measure the metal sulphide particle zeta potential and the settling properties were obtained by performing settleability measurements using an Imhoff settling cone. A suspension of copper sulphide particles was precipitated from synthetic solutions of copper and sulphide ions at equimolar concentrations. Immediately after precipitation the copper sulphide particles had a zeta potential of -50 mV and a settleability of about 7 ml.l-1. With the addition of copper ions the settleability increased by a factor of nearly three times and the zeta potential also increased to a maximum of -40 mV. A decrease in zeta potential to a minimum of -60 mV was observed after the addition of sulphide ions and this was associated with a settleability of 0 ml.l-1.

Jan 1, 2013

By M. Castelli, C. Scavia, S. Marello, A. Allodi

ABSTRACT – This paper investigates the possibility of interpreting the shear band evolution in hard soils and soft rocks as the result of shear propagation from pre-existing natural defects. Thesis done through the application of the principles of Fracture Mechanics, a Slip-Weakening Model(SWM) being used to simulate the non-linear zone at the tips of the discontinuity. Experimental observations have been carried out on prismatic samples of Beaucaire marl through biaxial compression tests in plane strain conditions. A numerical simulation confirms the validity of the proposed approach. RÉSUMÉ – Cet article présente la possibilité d’interpréter l’évolution des bandes de cisaillement dans les roches tendres et les sols raides comme le résultat de la propagation pour cisaillement à partir d’un défaut préexistant. Le Slip-Weakening Model (SWM) a été employé pour modéliser la zone non linéaire a l’extrémité d’une discontinuité. Nous présentons des observations expérimentaux obtenues à travers des essais de compression en déformation plane sur des échantillons prismatiques de marne. La simulation numérique d’un essai confirme la validité de la méthode proposée. KURZFASSUNG – Die vorliegende Arbeit versucht die Ausbreitung von Scherzonen in(bindigen) Böden und im Lockergestein anhand der Entwicklung von Scherrissen ausgehend vonexistierenden Schwachstellen zu erklären. Die Umsetzung erfolgte mit Hilfe der Bruchmechanik,für die Modellierung der nichtlinearen Zone an den Rissenden wurde ein Slip-Weakening-Modell(SWM) eingesetzt. Es wurden zweiaxiale Druckversuche an prismatischen Probekörpern vonBeaucaire Mergel unter der Bedingung eines ebenen Verzerrungszustandes durchgeführt. Dienumerische Untersuchungen bestätigten die Annahmen der untersuchten Theorie.

Jan 1, 2003

By Sergio Burelli, Darren C. Megaw

"Operational challenges associated with solvent extraction (SX) plants include the effective on-line management of solids introduced from a variety of process streams. Solids are carried over from leaching circuits due to incomplete solid–liquid separation, may be formed as a result of chemical precipitation within the SX circuits, or introduced from downstream electrowinning operations. Solids in SX settlers result in operational challenges that impact plant availability and reduce optimized name-plate design capacity operation. Most available SX crud and bottom solids removal systems are limited in their effectiveness to handle high total suspended solids in SX circuits. Operations are often forced to take settlers off-line for complete removal of contained solids. These cleaning operations are hazardous, high risk, labour-intensive and costly in terms of production down-time and organic extractant and diluent reagent losses. Production pressure results in operations being reluctant to take SX settler units off-line for solids clean-out, resulting in continued operation of the SX, at reduced levels of mass transfer performance. Crud ForxTM is an SX solids removal system, for the on-line removal of interfacial and bottom solids associated with hydrometallurgical SX processes. A case study conducted at Glencore’s Mutanda Mining copper and cobalt operation in the Democratic Republic of Congo demonstrated the effectiveness of the Crud Forx. Benefits identified were an overall improvement in SX fire risk reduction, SX occupational health and safety and an improvement in copper mass transfer. INTRODUCTION Hydrometallurgical copper extraction and purification processes are often associated with ultra-fine solids distribution profiles throughout the process flowsheet (Virnig et al., 1999). The level and impact of the undesired deportment of solids to process streams varies from operation to operation, but the common denominator for all operations that employ solvent extraction (SX) as a copper upgrading and purification step is that, at some stage, they will have to manage solids (crud) within the SX circuit. Available crud removal systems in the industry have had limited success in continuous, effective interfacial crud and bottom solids removal from SX settlers. Most operations use basic removal methodologies which, at best, only result in delaying the requirement for taking the affected SX settler stages off-line for complete clean-out. This operational methodology results in production loss, increased SX organic extractant consumption and adds occupational health and safety risk to SX operations. The integrated Crud ForxTM/Crud FrogzTM SX solids management system assists operations in on-line SX solids management. The system has been proven to significantly reduce the requirement for off-line cleaning of settlers."

Jan 1, 2015

By M .. Hori, H. Onishi, Y. Goda

The split-lining structure was newly developed for the air-tight lining of the underground compressed air storage cavern. This structure consists of separated reinforced concrete (RC) segments and air-tight membrane. It is most important for the Compressed Air Energy Storage Gas Turbine (CAES-G/T) system to develop the economical lining. In order to verify the applicability of split-lining structure, CAES-G/T pilot plant was constructed and operated for 6 months. We confirmed the practical usefulness and safety of this system through the operation. This paper presents the mechanical behaviour of surrounding rock mass and the lining structure observed through the operation of CAES-G/T pilot plant. Nous avons mis au point une structure de revêtement modulaire pour le revêtement des cavernes souterraines hermétiques à pression. Ce revêtement est composé de segments de béton armé et de membranes hermétiques. Il était très important, pour le CAES-G/T (Compressed Air Energy Storage Gas Turbine), de développer un revêtement économique. Afin de vérifier l’aptitude d’application de notre revêtement modulaire, nous avons construit un système pilote CAES-G/T et nous avons effectué des essais de fonctionnement pendant six mois. Ces essais nous ont permis de confirmer l’utilité et la sécurité du système. A travers le présent rapport, nous rendons compte de la structure de ce nouveau type de revêtement et du comportement mécanique de la masse rocheuse environnante que nous avons pu observer au cours desdits essais. Als luftdichter Druckbehälter wurde eine gegliederte Belagsstruktur für tief unterirdisch liegende Felshöhlungen entwickelt. Diese Struktur ist aus Stahlbetonabdeckung und luftdichter Plane aufgebaut. Bei der Entwicklung des Pressluftgasturbinen – Stromerzeugungssystems (CAES-G/T) war es die wichtigste Aufgabe, einen wirtschaftlichen Belag zu entwickeln. Deswegen wurde zum Nachweis der Effektivität der gegliederten Belagsstruktur eine Pilotanlage errichtet und 6 Monate lang betrieben. Durch den Betrieb konnten wir die Praktikabilität und Sicherheit des Systems bestätigen. Dieser Aufsatz ist ein Bericht über das Verhalten der durch Betrieb der CAES-G/T Pilotanlage beobachteten Belagsstruktur und umliegenden Felsmasse.

Jan 1, 2003

By G Njowa

Mineral resource evaluation and estimation process is not an exact science; however it depends on the knowledge and experience of the competent person and his ability to apply his mind, make reasonable assumptions, interpretations and exercise sound judgment in the mineral resource estimation process. The mineral resource evaluation results in a mineral resource statement are disclosed to investors. The minerals industry is presently undergoing rapid changes in legislation governing the public reporting of mineral assets. It has gone through different phases of development with respect to the reporting of mineral resources and mineral reserves (mineral assets). In the past no reporting was done and currently mineral assets are reported as a supplementary section that briefly describes the mineral asset termed ?the mineral reserve and mineral resource statement?. The current industry trend appears to be going towards recognition and disclosure of the mineral assets on to the balance sheet. This paper explores the salient issues behind the mineral resources and mineral reserve statement of vein and reef deposits published in the public domain. It also highlights the potential misleading consequences of these issues and which filter through to the valuation of these particular mineral assets. The creation of reporting standards in the minerals industry has made significant inroads in standardizing and consolidating the interpretation and understanding of the different classification categories in the industry in an effort to promote common interpretation towards these salient issues.

Jan 1, 2008

Scenario reduction is designed for selecting a representative subset of geostatistical simulations out of a much larger set. Three steps are involved: measuring the dissimilarity between two simulations; finding a metric to measure the distance between any subset of k simulations and the full set of N simulations; and finding an efficient algorithm for selecting the subset that minimizes the metric. This paper focuses on the third question. We show that genetic algorithms are an efficient way of approaching the minimum when the population of subsets to be sampled is large. Two case studies based on the Walker Lake data-set are presented: firstly choosing k=4 simulations out of a total of 100, and secondly choosing 20 out of the same 100 simulations. In the first case it was possible to compute all possible combinations exhaustively and hence to demonstrate that the algorithm converges to the true minimum. This was not possible in the second case. Instead we demonstrate that it outperforms the random draw algorithm used in earlier work. A procedure for tracking individual selections during the iterative procedure was developed. This allows us to measure the evolution in the percentage of progeny resulting from crossing-over and from mutation that survived in the next generation. It gives valuable insight into how to choose the parameter values in the algorithm. Another key finding is that there is a trade-off between the number of individuals per generation and the number of generations required for the algorithm to converge.

Jan 1, 2014

By P. A. Lilly, W. Sarunic

In most cases, slope movement monitoring data are collected on a temporal basis and displacement or velocity is plotted against time in order to assist the engineer to make judgements about slope behaviour. Once an unusual behaviour pattern has been established, the data are then analysed to estimate when the key inflection points occur in the data, when the slope movements start to accelerate and, ultimately, when the slope is expected to collapse. The identification of these inflection points is sometimes difficult to achieve with the naked eye. This paper presents the application of a trend analysis technique, known as cusums, to assist in this process. The authors have presented a range of data from various real life examples which highlight the effectiveness of the cusums technique. A key aspect of the cusums technique is the use of a constant (K) against which data trends are assessed. This constant is best derived from slope performance data at each site, as each rock mass will behave in its own unique way. The authors have experienced slopes that have had threshold values ranging from 0.1mm/day through to 10mm/day, and therefore a conservative approach should be adopted when assessing the performance of slopes.

Jan 1, 2006

By J. P. Theron

Paper written on project work carried out in partial fulfilment of Phd.(Process Engineering) degree Process modelling is an essential element in the development of advanced (model-based) process control systems, accounting for up to 80% of the cost of development. Often, models based on historic process data are the only viable option when dealing with processes that cannot be modeled cost-effectively from first principles. Despite major advances that have recently been made in the field of nonlinear process modeling, some basic idea of the dynamic behaviour of a process system is important prior to system identification. While many process systems seem unlikely to be linear, the possible nonlinear aspects of their dynamics are not necessarily supported by the data. This may have significant implications for subsequent system identification or interpretation of the data. For example, it is quite possible that an underlying nonlinear deterministic signal may be obscured by a high degree of measurement or process noise, to the extent that it may be critical in the choice of model to fit to the data. The method of surrogate data analysis has recently been proposed as a means to classify the underlying dynamics of complex systems, and in this paper the use of Fourier transform surrogates to classify process systems is explored. Keywords: modelling, process control, simulation, surrogate data analysis, nonlinear systems.

Jan 1, 2004

By A. F. Lee

A pick-up apparatus capable of yielding quantitative results has been described. Studies of some collector-mineral systems have been presented to illustrate the versatility of the apparatus and prove the validity of results.

By M. Syamujulu

In 1994, Nkana smelter commissioned a multimillion US Dollar Chilean Teniente converter (CT) in its operations in order to improve its smelting technological base. The main objective was to reduce the overall smelting energy costs and increase the sulphur capture for sulphuric acid production to support the company?s leaching operations at Nchanga tailings leach plant. A decade of CT operations have since ensued following its installation and start-up. This paper provides a technical and operational audit of the performance of the CT in the first 10 years of its operations at Nkana smelter.

Jan 1, 2005

By A. Mainza

It is common practice in the mineral processing industry to use hydrocyclones for particle classification. However, classification in the UG2 platinum circuits using the hydrocyclone poses major challenges due to the differences in density between silica and chromite, the two major components of this ore. Silica, the PGM carrying component, has an average density of 2.7 and the barren chromite component has an average density of 4.5. When conventional and flat bottom cyclones are used there is a misplacement of particles due to differences in density leading to inefficiencies in the classification by size. As a result of the density effect, coarse silica reports to the overflow, resulting in loss of recovery, and fine chromite reports to the underflow, resulting in loss of milling capacity and unnecessary production of fine chromite. A classifier based on a different concept was required in the classification of UG2 platinum ore. The three-product cyclone, which is a hydrocyclone with two concentric vortex finders to produce three distinct products, has been tested in the UG2 ore application and indications are that misplacement of particles due to differences in the component densities can be minimized through the use of this unit. Industrial and pilot plant trials were conducted and indications are that the three-product cyclone can be installed to selectively produce a middlings stream that can be screened using Pansep screens to provide a screen oversize, which is predominantly coarse silica that can be preferentially reground to recover the PGM values contained in the coarse silica.

Jan 1, 2005

By H. Yavuz

Physical modelling is one of the research tools in the understanding of the failure mechanisms and the deformations likely to be experienced by the strata during mining operations. Success of the physical models to predict the strata behaviour depends on satisfaction of the scaling requirements in modelling material used. This paper gives results from a laboratory work carried out into the factors influencing the strength and elastic properties of a physical model material to satisfy the scaling requirements determined from application of dimensional analysis to the pertinent variables affecting the deformation and failure of the underground structures. It was found that the conditions for preparing the material over its composition had a great influence on the final properties. The effect of different water quantities, sand size and mixing time upon the properties of modelling material was studied and water requirement for different proportions of sand/plaster to prepare the material was optimized. Various sand/plaster ratios of compositions were cured at three different levels of oven temperatures. Curing at low temperature produced material within the average modulus ratios ranging from 290 to 432, which are common to most rock types according to Deere?s rock classification, whilst curing at high temperature produced material within the low modulus ratios ranging from 64 to 140 depending on its composition. A combination of low and high temperature curing resulted with an increase in modulus ratio compared to high temperature curing. Curing the material at low temperature compared to other curing temperatures provided a satisfactory range of strength ratio. It has been shown that the relative amount of filler to plaster in the mix controls the frictional properties of the material and results with an increase in strength and modulus ratio of the material provided that suggested preparation and curing conditions were applied. Model material developed by curing at low temperature simulated modulus ranging from 241 to 343 and strength ratios ranging from 11.6 to14.8 of a coal mine rocks, satisfactorily.

Jan 1, 2003

By M. E. Rossi

All large-scale applications of conditional simulations intend to benefit from the ‘correct’ (or’ accurate’) characterization of uncertainty, adequately describing the variability observed from the data and its impact on the final objective. This paper discusses a number of relevant issues that highlight the extent to which, in reality, a model of uncertainty is dependent on the random function model chosen. Often in the presence of large number of conditioning data most available random function models will provide similar models of uncertainty. When conditioning is scarce, the resulting models of uncertainty will vary more widely, since the final output will depend mostly on the underlying assumptions of the model chosen. The application described in this paper is taken from a large porphyry Cu operation in northern Chile, and it demonstrates the impact of several variables on the resulting models of uncertainty. In particular, some of the decisions involved include the number of conditioning data and the underlying Random Function model used (Gaussian or indicator-based). Also, implementation-specific parameters must be decided upon, such as grid size used, random number generator, simple or ordinary kriging, multiple-grid simulation, and simulation of irregular three-dimensional bodies (as opposed to regular grids). Some practical guidelines are proposed to deal with these decisions.

Jan 1, 2003

Council for 2004/2005 President F.M.G. Egerton President-elect W.H. van Niekerk Vice-presidents Senior R.P.H. Willis Junior R.G.B. Pickering Immediate Past-president T.R. Stacey Honorary Treasurer J.A. Cruise

Jan 1, 2005

This publication is provided on an "as is" basis without warranties of any kind, either expressed or implied including, but not limited to warranties of title or implied warranties of merchantability of fitness for a particular purpose. The information contained in this publication is for general information purposes only. It does not constitute professional, technical, financial or other advice to the user of this publication and must not be relied upon as such by any person whatsoever. The use of this publication is at the users own risk. The authors/creators of the information contained in this publication have tried to ensure that the information contained herein is correct, but errors or inaccuracies may exist or the information may be incomplete, unreliable or no longer up to date. Therefore, no warranties of any nature whatsoever are given and any liability to any person in respect of anything and in respect of the consequences of anything done or omitted to be done, wholly or partly in reliance upon the whole or any part hereof, are disclaimed, including and without limitation any contractual, dialectal, direct, consequential or financial damages or losses. On no account will Organisers and/or any of the contributors or any person or entity involved in creating, producing or distributing the information and or software available in this publication be liable for any such damages arising out of the use of or inability to use this publication. Copyright Reserved The South African Institute of Mining and Metallurgy P O Box 61127, Marshalltown 2107, South Africa www.saimm.co.za All rights reserved. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical photocopying, recording or otherwise without the written permission of the copyright owner. Although the greatest care has been taken in the compilation of the entire contents, the editors and publishers do not accept responsibility for errors or omissions. First Edition Copyright February 2004 Proceedings ISBN: 0-9584663-5-1 (1 volume and CD-ROM)

Jan 1, 2004

By Helge Rosenberg

Up to now, Topsøe WSA (Wet gas Sulphuric Acid) plants have been in operation for almost 30 years, and close to 80 plants have been sold. In spite of its unique features and ability to treat gases without any prior drying, the WSA technology has had certain restrictions with regards to SO2 concentration in the feed gas, and the overall conversion of SO2 by catalytic means has been limited to approx. 99.7%. In commercial scale sulphuric acid production on the basis of elemental sulphur and metallurgical off-gases, there is a demand for higher SO2 conversion and treatment of gases with a higher content of SO2. Therefore Topsoe has further developed its WSA technology to cope with these demands. This paper will explain more about the principles of such new development and leave the delegate with a better understanding of the potentials of the new generation of the WSA technology from Topsoe.

Jan 1, 2009

By Helge Rosenberg

Up to now, Topsøe WSA (Wet gas Sulphuric Acid) plants have been in operation for almost 30 years, and close to 80 plants have been sold. In spite of its unique features and ability to treat gases without any prior drying, the WSA technology has had certain restrictions with regards to SO2 concentration in the feed gas, and the overall conversion of SO2 by catalytic means has been limited to approx. 99.7%. In commercial scale sulphuric acid production on the basis of elemental sulphur and metallurgical off-gases, there is a demand for higher SO2 conversion and treatment of gases with a higher content of SO2. Therefore Topsoe has further developed its WSA technology to cope with these demands. This paper will explain more about the principles of such new development and leave the delegate with a better understanding of the potentials of the new generation of the WSA technology from Topsoe.

Jan 1, 2009