Search Documents

By P. J. D. Lloyd

The widely employed IPCC models for the release of methane from underground coalmining operations are reviewed, and put in the context of the South African National Communication on greenhouse gas emissions. Then attempts to calibrate the model via measurements on South African coalmines are described. These attempts failed because it rapidly became clear that the IPCC model, involving methane adsorbed by the coal and released (a) by the depressurization of the strata caused by mining, (b) from the broken coal and (c) from coal remaining in roof, floor, pillars or goaf after mining, was not valid. Instead, measurements showed that the methane release was very variable, sporadically falling to zero. Carbon dioxide concentrations were monitored at the same time as methane, and followed methane concentrations. An alternative model was developed, in which methane was largely displaced from the coal and held in fissures, cleats and pores, which, when intersected by mining, released methane into the ventilation stream. In a key test of this hypothesis, methane concentrations around a continuous miner were monitored both during operation and after shutdown. Even during operation, methane became undetectable. It is hypothesized that heating of the South African coal-seams during the emplacement of the igneous dykes that cut so many of the seams caused displacement of the methane from the coal into the pores. This fissure-held methane, or free methane, is released rapidly once a pathway through the coal into the mine atmosphere is established. In contrast, methane adsorbed in the coal, and measured as the seam gas, desorbs relatively slowly. Measurements suggest that on average about 50%of the adsorbed methane is lost one day after mining. By that time, the coal will have left the mine, so that the remaining seam gas will be released to the atmosphere outside the mine. Attempts to measure methane emissions from surface coal-mining operations showed very little detectable methane. Coal from surface operations, which was milled and exposed to atmosphere, adsorbed gas from the air. It is concluded that methane release from surface operations is probably less than 3Gg/a. It is estimated that the total methane release from the coalmining industry amounts to about 72 Gg/a, as opposed to the National Communication estimates of 323 Gg/a in 1990 and 317 Gg/a in 1994. However, there are large errors associated with these estimates, and it is recommended that the methodology outlined in this report be extended to as many mines as possible to reduce the errors that are inherent in the physical processes underlying the release of methane from South African coalmines.

Jan 1, 2005

By P J. Grobler

The current commodity boom is depleting the ore bodies at a rate not seen in the past. As the existing ore bodies get depleted, only the more inferior bodies are left for exploitation. This places an emphasis on beneficiation to upgrade the lower grade ore to high-grade feedstock for downstream processes. This paper discusses the role of dense medium separation in this quest for high-grade feedstock for the future. It covers the production and utilization of ferrosilicon and gives a future perspective of the technology. It concludes about the way ahead and the challenges facing the processing fraternity and mining industry.

Jan 1, 2006

By L. R. Nelson

A review is presented of the furnace cooling system design and operating developments since the initial furnace start-up in January 2001 of the Chambishi DC-arc furnace to produce ferrocobalt alloy. The furnace operating conditions present a number of challenges to the furnace designers and operators, in particular, to provide a sustainable lining that can withstand the highly corrosive siliceous slag (roughly 50% SiO2). This is exacerbated by the dual requirement of operating this slag in a relatively highly superheated state (?T ?400°C when tapped at 1550°C) to ensure that the ferroalloy can be tapped (estimated 1370°C alloy liquidus temperature) prior to atomization. The core design challenge occurs at the alloy-slag interface, where a single refractory type cannot simultaneously meet the dual requirement of both adequate alloy and slag corrosion compatibility. Progression by the fourth furnace campaign to involve a retrofit of the bath sidewall to HATCH high-intensity, water-cooled, copper Waffle coolers and tap blocks is described. This involves operation of the entire slag bath, the slag-alloy interface and a portion of the alloy within a more chemically compatible refractory/slag (and possibly at times even an alloy) freeze-lining. Due to the high furnace power density employed (up to 500 kW/m2 hearth area), coupled with the large slag superheat needed, the resulting imposed peak bath sidewall heat fluxes are substantial, especially in the alloy (typically averaging 170 kW/m2), and on occasion have exceeded 1000 kW/m2. The performance of the HATCH Copper Waffle coolers under such aggressive process pyrometallurgical conditions is described. Aspects of the design and especially operating strategies to effect sustained production at up to 38 MW power input are also discussed.

Jan 1, 2004

By Carl Havemann

[PAPER PRESENTED AT THE 8thINTERNATIONAL CORROSION CONFERENCE HELD AT THE SA NATIONAL MUSEUM OF MILITARY HISTORY, SAXONWOLD JOHANNESBURG DURING 14-15 NOVEMBER, 2006.]

Jan 1, 2006

By Merete Tangstad, Kai Tang

The primary aim of the present investigation is to develop a model which permits to calculate/predict the viscosities of ferromanganese slags, typically focus on the MnO-SiO2-Al2O3-CaO-MgO-FeO multicomponent system. The present viscosity model emphasizes the ability of prediction, i.e. using the binary parameters to extrapolate the viscosities in ternary and higher order systems. To this end, a physical sound model is essential. Temperature dependence of viscosity is described by the Eyring?s formalism. The well-known cell model is used to define the SiO44- tetrahedra in the silicate melts. Composition dependence is expressed in term of viscous activation energy, which is characterized by the binary structural units. The viscosities in ternary and higher order systems are hence predicted using the binary activation parameters. The model has been used to calculate the viscosities in the whole liquid composition range of ferromanganese slag.

Jan 1, 2007

By J. A. Bakken, T. Magnusson, G. Sævarsdottir

This paper describes measurements of current and voltage done on submerged arc furnaces. The aim is to focus on and attempt to separate from one another the electric arc current and the current bypassing the arc through the charge. Toward this goal two measurement campaigns on AC-arcs burning on coke beds are ac-counted for. The first was done on a 150 kVA pilot furnace at SINTEF in Trondheim Norway, and the second one was done on a 48 MVA industrial furnace run by Icelandic Alloys in Iceland. The measurements were compared to simulations employing an advanced MFD arc model. The main results are that a coke bed does not necessarily behave as a linear conductor. However the warmer chemically transformed part of an operating Si-metal or FeSi furnace probably exhibits linear behaviour and passes a considerable fraction of the phase current, perhaps on some operating conditions, as much as 50%.

Jan 1, 2007

By C. C. Oosthuizen

Paper written on project work carried out in partial fulfilment of Technikon Practical Training Frank shaft is mining both Merensky reef and UG2 reef. The Merensky orebody is almost depleted and this was the reason for starting to mine the UG2 ore reserves. It was decided to mine the UG2 orebody with trackless equipment using a bord and pillar mining method. Frank shaft has been mining the UG2 orebody for nearly 5 years. The T-cut mining method was introduced to see if it could improve the grade of the run of mine (ROM) as well the extraction percentage.

Jan 1, 2005

A shortage of technical skills in all areas of the mining industry is being experienced worldwide. This has significant consequences for design, operations, productivity and safety and, therefore, needs to be seriously addressed, both in the short and longer term. It is therefore both a strategic and a tactical issue. Importantly, however, since mining is a long-term business, the shortage of skills must be dealt with from a strategic point of view to ensure the supply of the necessary skills for future mining. This paper will deal specifically with the provision of high level technical skills, that is, university graduates in mining engineering, and the outlook for the institutions that are currently producing such graduates.

Jan 1, 2008

By N. E. Yasitli

There is a considerable amount of lignite reserve in the form of thick seams in Turkey. It is rather complicated to predict the characteristics of strata response to mining operation in thick seams. However, a comprehensive evaluation of ground behaviour is a prerequisite for maintaining an efficient production, especially when top coal winning by means of caving behind the face is applied. A comprehensive modelling of deformations and induced stresses is vital for the selection of optimum production strategy. In this study, numerical modelling and analysis of a longwall panel at Omerler underground coalmine have been carried out by using the software called FLAC3D developed based on the finite difference technique. Firstly, a 3-D numerical model of the M3 panel has been prepared. Secondly, induced stresses formed around the longwall face have been determined as a function of face advance where the face was located at the bottom of thick coal-seam. Results obtained from modelling studies have revealed that the front abutment vertical stress was maximum at 7 metres in front of the face and magnitude of front abutment stress was found to increase up to a distance of 200 metres away from the face start line. As the face was further advanced after 200 m from the face start line, there was not any significant change in the characteristics of front abutment stresses. Results of numerical analysis of the panel were in good agreement with in situ observations.

Jan 1, 2005

By A. T. Haile

Detailed monitoring of the response of the rock mass between rockbolt reinforcement units subjected to a simulated seismic source has been successfully conducted. This work has shown the increase in amplification of the Peak Particle Velocity (PPV) with distance from a rock bolt unit, and, a minimum PPV for rockburst damage for the given site characteristics. This understanding, at this site, will allow the design of a suitable rock bolt spacing to prevent unravelling of the rock mass between the rock bolt units for a given level of seismicity. Or, alternatively, an estimation of the requirement for a suitable fabric support system, for the anticipated level of seismicity, can be made.

Jan 1, 2001

By A. Chryssoulis, D. Venter, R. Dunne

An often-overlooked parameter of flotation processing is the impact of surface chemistry. Flotation processing, being a heterogenous process is largely reliant upon the chemistry occurring at the interfaces between solid-liquid phases. Development of analytical techniques such as Auger electron spectroscopy, X-Ray photoelectron spectroscopy (XPS) and low energy electron diffractions (LEEDS) has allowed for a dynamic view characterizing surface composition and structures. The advent of ‘static’ systems, capable of measuring ultra-thin layers on surfaces at low concentrations, was the next step in surface analytical developments. In general, it is the low concentrations and fragmentation patterns which limit the analysis of certain chemical species at plant concentration ranges. At present, analysis of inorganic and organic surface modifiers by time of flight mass spectrometers with a variety of ionization techniques has become a common analytical method to measure chemical species on the outermost surface of mineral particles. By studying the relationship between surface analysis results with metallurgical outcomes, the implications of the presence of surface species can be determined. The presence of flotation activators or depressants can be established using Laser Ionization Mass Spectrometry (LIMS) and Resonant Ionization Mass Spectrometry (RIMS) which are highly versatile surface sensitive analytical techniques. A case study applied to sphalerite flotation in the Neves Corvo Cu-Pb-Zn concentrator and the implication inorganic surface modifiers have is presented. By determining the relative concentrations of Cu, Pb, oxidation products, Ca and other surface species in floated and rejected mineral particles, rationale for improving recovery and selectivity is elucidated. Keywords: Cu-Pb-Zn Flotation, Process Mineralogy, Surface Chemistry, Flotation kinetics

Jan 1, 2020

Sulphide minerals, such as pyrite and sphalerite, are leached by ferric sulphate. This reaction produces ferrous sulphate and other dissolved products. The ferrous sulphate is re-oxidized to ferric sulphate by bacteria. These reactions can be written as: [ ] However, in 1964 Silverman and Ehrlich proposed that this is not the only role that is played by bacteria. These researchers proposed that T. ferrooxidans enhances the rate of oxidation of pyrite above that achieved by chemical reaction with ferric sulphate at the same solution conditions. This enhancement in the rate of dissolution was proposed to occur by direct microbiological action, possibly by the extra cellular secretion of an enzymatic oxidant. Since the Silverman and Ehrlich proposal, different authors have made opposing claims concerning the action of T. ferrooxidanson pyrite. This ?direct mechanism? of bacterial dissolution of pyrite can be given by the following reaction: [ ]

Jan 1, 2000

By A. M. Bryukhanov, A. G. Mnukhin

The report states accident rates for gassy/dusty coal mines represented as an ergatic system "man – machine - environment" with further analysis by the method of conditional probabilities. A coal mine has been analyzed with allowance for the attending personnel, equipment and environment as a sequence of events and states. Probabilities of operational states have been determined and prediction of mine behavior has been made on the basis of investigation findings for equipment and the personnel states, and analysis of the environment (i.e. mine and mining conditions). Utilization of expert estimation methods has been considered for determining major operational parameters of gassy/dusty mines. The importance of standardized values of permissible occupational risks (permissible probability of accident, PA) is demonstrated. It is also stated that a procedure is essential to determine these values, involving regular check-ups of the integral safety criterion at all mines and further development of customized recommendations for individual mines on efficient improvement of accident situations. Methodology to determine the assessment criteria has been developed and scientifically substantiated for permissible accident rates in hazardous industries.

Jan 1, 2003

By B. Salt, R. Sullivan, E. Roos, M. de Vries, K. McKenna, L. R. Nelson, M. J. N. Uys, P. Jacobs, E. Munnik, P. Lewarne

A review is presented of the furnace cooling system design and operating developments since the initial furnace start up in January 2001 of the Chambishi DC-arc furnace to produce ferrocobalt alloy. The furnace operating conditions present a number of challenges to the furnace designers and operators in particular to provide a sustainable lining that can withstand the highly corrosive siliceous slag (roughly 50% SiO2). This is exacerbated by the dual requirement to operate this slag in a relatively highly superheated state (?T ? 400°C when tapped at 1550°C) to ensure that the ferroalloy can be tapped (estimated 1370°C alloy liquidus temperature) prior to atomisation. The core design challenge occurs at the alloy-slag interface, where a single refractory type cannot simultaneously meet the dual requirement of both adequate alloy and slag corrosion compatibility. Progression by the fourth furnace campaign to involve a retrofit of the bath sidewall to Hatch high-intensity, water-cooled, copper Waffle coolers and tapblocks is described. This involves operation of the entire slag bath, the slag-alloy interface and a portion of the alloy within a more chemically compatible refractory/slag (and possibly at times even an alloy) freeze-lining. Due to the high furnace power density employed (up to 500 kW/m2 hearth area) coupled with the large slag superheat needed, the resulting imposed peak bath sidewall heat fluxes are substantial, especially in the alloy (typically averaging 170 kW/m2), and on occasion have exceeded 1000 kW/m2. The performance of the Hatch Copper Waffle coolers under such aggressive process pyrometallurgical conditions is described. Aspects of the design and especially operating strategies to effect sustained production at up to 38 MW power input are also discussed.

Jan 1, 2004

By H. Ogasawara

Information on rock stress is important for safe mining in seismically active ground. On a major gold mine, a few tens of crews are continuously conducting geological drilling with small pneumatic machines. However, stress measurements are not often carried out in South African deep-level gold mines. One of the reasons is the drilling diameter that overcoring requires, which is much larger than the diameters used in regular geological drilling, e.g. Boart Longyear Metre Eater, which drills A[O] or B[O] holes. Larger diameter holes result in slower drilling advance, more load in transportation and handling at sites, and higher cost. In order to enable overcoring in BX size (60 mm diameter), we modified the compact conical-ended borehole overcoring (CCBO) technique that has been suggested by International Society for Rock Mechanics (ISRM) and was originally designed for NX drilling (76 mm diameter). With a single overcoring, the 3-D stress tensor can be determined. We tested this modified method at a depth of about 3 km at Moab Khotsong mine in South Africa. We worked with drilling crew who usually work at geological drilling with the Metre Eater. In January 2011, we tried using regular geological drilling tools (a sequence of a normal BX bit, reamer, and rod) without success. In August and September 2011, introducing stabilizers and thin BX bits, we succeeded. We could complete a cycle of procedures necessary for an overcoring, including shaping the borehole-end conically, glueing a 16-element strain cell, and overcoring, within 2.5 hours. Only 10 cm overcoring is needed, which increases the chance of successful overcoring in heavily fractured conditions. This modified method is suitable for up-dip holes to depths of 10-15 m from tunnels, and has the potential to be widely used at the initial stage of geological exploration drilling at many localities.

Jan 1, 2012

As the world continues to face the turmoil of the economic environment, legislative prerequisites and physical conditions the intervention of technological development is vital for the continuation of the ancient source of revenue: mining. The Palabora underground mining project is a state-of-the-art shaft mining system that will prove to be a benchmark in its field for years to come. An integration of modern technology?both in application and development?has resulted in a shaft system that is intrinsically holistic. Every aspect of the mining and production process has undergone thorough investigation, simulation and innovation to ensure that every component is selected by design and not simply conforming to past practice or trends. The process philosophy includes proven technology such as to promote the lowest operating cost and process time with the highest yield. The underground mining system is in the final stages of commissioning and will shortly be producing a nominal 30 000 tons per day with a predominantly automated system. This paper discusses the complete state-of-art shaft system developed for the Palabora underground mine, and refers particularly to the headgear, the winders, the conveyances and the shaft guide system, as well as the loading system developed specifically for the high performance requirements of the mine.

Jan 1, 2000

By J. Kirsch

Keywords: Pyrometallurgy, pneumatic transport, pneumatic transport Dense-phase pneumatic injection has begun to replace more traditional furnace-feeding systems. The paper describes the technology as it is applied to processes where the back pressure at the point of injection is greater than 50 kPaG. It reviews earlier systems of injection and more recent developments that address concerns for instantaneous control in modern smelters. The new technologies fall into two groups, (1) modified pressure-difference control (sub-divided into simple and complex) and (2) mechanical-feeder-based control. Features of current injection systems include feed splitting in two forms, passive and active, and co-current injection.

Jan 1, 2006

The relationship between neural network (NN) performance and the parameters that form the architecture of the neural network is complicated. This paper studies an issue that is still controversial—the effect of the number of neurons and number of hidden layers on NN performance. This paper tests if the above parameters affect network performance when the NN is trained according to the quick stop strategy. It was determined that the number of neurons did not have any effect on the NN performance for a single layer or a double layer network. It was also found that the training error and calibration error could be poor indicators of the prediction correlation coefficient.

Jan 1, 2003

By A. Cichowicz

In this study, techniques used to design earthquake-resistant structures are applied to the deep-level mining environment. Earthquake engineers seek to identify the cause of potentially damaging resonance, and design or reinforce structures to reduce these effects. Similar techniques have been used to analyse the dynamic behaviour of the rock mass surrounding a stope in a deep South African gold mine. A three-dimensional seismic array installed in a stope at TauTona Mine (previously Western Deep Levels, East Mine) provided an opportunity to examine the evolution of the wave field close to an underground opening. A set of three-component geophones installed in a borehole above the panel revealed the development of surface waves as wave fronts reached the excavation, and an array of vertical component geophones fixed to the hangingwall provided a two-dimensional map of site effects. While the collected data do not include damaging seismic events, quantitative analysis enabled phenomena which could lead to damage, to be recognized. In the vicinity of the excavation, the energy of the seismic signal is generally transformed from high frequency to low frequency. It was found that seismic events with relatively high corner frequency (150 Hz?200 Hz) usually excite several modes of vibration (30 Hz to 110 Hz), while events with low corner frequency (30 Hz?50 Hz) do not always excite higher modes of vibration in the structure. This implies that the rock mass around the excavation is a complex medium, and should be studied using the multi-degree-of-freedom model. A strong structural effect (due to the excavation shape) was revealed as a low frequency coda wave (at 40 Hz and 60?70 Hz), well developed on the skin of the hangingwall. A strong site effect was revealed by changes in signal properties between hangingwall geophones, exhibiting strong resonances around 160 Hz and in the range 200 Hz to 300 Hz.

Jan 1, 2000

The extraction of minerals and coal at greater depth, employing higher-powered machinery to improve production levels, imposes an increased burden on the ability of a ventilation system to maintain an acceptable mine climate. Hence, mechanical mine cooling systems are often adopted, which can be expensive in terms of both their associated capital and operating costs. Consequently, in order to optimize the total mining costs, it is essential to provide the mine operator with a method with which to determine the most cost effective and efficient mine cooling system. In a previous paper1a novel energy analysis employing the concept of exergy was proposed and applied to cooling systems applied to two conceptual model mines, representative of UK deep coal operations, and their resultant subsurface thermal environ-mental conditions predicted. This paper presents an analysis of the results obtained from the application of this novel technique to assess the performance of various cooling systems applied to a current UK colliery that is experiencing climatic problems due to its depth and highly mechanized production and development workings. To perform this analysis, ventilation and climatic data collected at the case study mine were used to construct balanced mine ventilation and climatic network models to replicate the subsurface environment. Where air conditions exceeded specified climatic limits within identified climatically control zones, mechanical mine cooling systems were employed. A number of cooling system configurations were applied to these model to investigate the potential to satisfactorily regulate the thermal environment. The heat energy transferred out of the air stream by the various cooling methods was absorbed using a variety of chilled water systems, which were designed to operate at various water flow rates and temperatures. Models of various cooling system were developed and applied to control the underground climate within this mine network to within pre-set climatic limits. The results of a comparative analysis of the energy transfers that were produced by the application of the different cooling systems are presented in the form of exergy performance indices. The results produced by simulation models constructed to represent chilled water distribution networks to supply the various air coolers, are designed and balanced. The results of the exergy analyses applied to the operation of the various chilled water pipe networks are discussed and used to assess the exergetic performance of the application of each proposed cooling system to the mine ventilation network.

Jan 1, 2004