Search Documents

By R. C. Adams

This report describes the feasibility of mining the oil shale deposits of the Piceance Creek basin in Colorado by an integrated open pit system. The study is based upon a comprehensive analysis of pertinent environmental, economic, and engineering factors. Ten mining cases are investigated, and the mine design and cost estimates for each case are presented in this report. Nine of the cases represent three cutoff grades, defining oil shale ore as equal to and above 15 gallons per ton (gpt), 20 gpt, and 25 gpt at three ore production levels of 500,000 tons per day (TPD), 1,250,000 TPD, and 2,500,000 TPD. The tenth case is an alternate design of the 500,000 TPD production rate at the above 15 gpt cutoff grade. The report consists of Volume I, a technical and cost comparison of the ten cases; Volume II-Part I, a detailed explanation of the estimating methods used; and Volume II-Part 2, a more detailed discussion of the technical and cost features of the ten cases than is presented in Volume I.

Jan 1, 1976

By R. L. Soderberg

This paper is one of a series on mining methods and costs being published by the Bureau of Mines. It describes briefly the mining methods employed since the start of operations in 1937, with emphasis on the diamond-drill blast-hole method of ore breaking and slusher-drift method of ore drawing at the Holden mine of the Howe Sound Co., Chelan Division, Holden, Wash. The Holden mine is in the north-central part of the Cascade Range, 11 miles up Railroad Creek from Lake Chelan. The nearest railroad is at Chelan Falls, 40 miles by boat and 4 miles by highway from the mine. All freight comes into the mine and all concentrates are shipped out via Chelan Falls. The altitude of the main haulage level is 3,500 feet. Railroad Creek Valley is covered with a dense growth of fir and spruce, while most of the surrounding mountains are rocky, with sparse timber growth.

Jun 1, 1948

These inspection standards have been prepared for use in the Federal inspection of bituminous and lignite mines. They are a revision of "Tentative Coal-Mine Inspection Standards," published as Bureau of Mines Information Circular 7204 in February 1942 and employed a guide for Federal inspections. Numerous changes have been made in the original standards owing in part to recognition of shortages of some types of safety equipment due to the war, in part because of need of additional standards to cover certain mine conditions' arid' practices, and in part to conditions not foreseen when the original standards were prepared. About one-fourth of these standards are marked with an asterisk (*) as being of particular importance in preventing accidents in many coal mines; however; failure to carry out the suggestions made in such of the other standards as are applicable may also' lead' to the loss of lives.

Jan 1, 1943

By Kevin Malone

Mercury, or quicksilver as it is often called, has many applications in modern technology. Used principally in electrical apparatus, industrial contol instruments, insecticides and fungicides, electrolytic preparation of chlorine and caustic soda, chemical processes, pharmaceuticals, and dental preparations, the liquid metal has unusual properties that make it a preferred material for many industrial uses. United States consumption of mercury during the past 40 years shows a rising trend. In all except 4 years, U.S. production has been less than the domestic requirement, and imports, principally from Spain, Italy, and Mexico, have supplied most of the deficit. After World War II, domestic output decreased rapidly until 1950, when it was the lowest in the 100 years covered by production records. Higher mercury prices since 1950 have reversed the decline in domestic output and reduced the gap between U.S. production and consumption. Domestic output in 1958 was the highest in peacetime since 1883; however, the nation still imported 28 percent of its mercury requirements from 1950 to 1960 the price of mercury was high as a result of industrial applications of the mercury cell, the impact of the cold war and the Korean war, and the Government stockpiling program. The stockpiling program, in effect, put a floor under mercury prices even though only 9,428 flasks of domestic mercury went into the stockpile under the original program which ran from July 1954 to December 31, 1957. Under an extension of the program, an additional 17,463 flasks was purchased.

Jan 1, 1962

By R. E. Heithecker

In Kansas, almost every oil well drilled into a limestone formation is treated with hydrochloric (muriatic) acid upon completion. This is done to increase the potential capacity of the well and thereby increase its "daily allowable" production (see p. 9 ), to shorten the time required to produce the recoverable oil, and to increase the quantity of oil recovered ultimately from the reservoir. The porosity and. permeability of limestone formations seldom are uniform throughout the proved area, consequently the production capacities of completed wells vary considerably. Acid treatment of wells tends to increase production capacity and to equalize potential capacity. If offset wells already have been treated with acid, new wells usually are treated to protect the property on which they are drilled against drainage. Even though competitive conditions do not exist in a field, it

Jan 1, 1939

By Lewis M. McNay

The Bureau of Hines and industry (mining and private) have studied the placement of hydraulic sandfill in deep-vein mines to identify existing problems and to develop techniques to strengthen the support characteristics of the sandfill. The hydraulic sandfill system, physical properties of typical classified mill tailings, and properties of sandfill modified by various techniques are discussed. Computer analysis has defined the support capability of various sandfills using actual mine field data as a reference base. High-modulus sandfill can provide adequate support in deep-vein mines to alleviate rock and pillar stresses and to reduce rock-burst incidence.

Jan 1, 1975

By Arthur L. Crawford, R. E. Head, Glen Burgener, F. E. Thackwell

"INTRODUCTION This report embodies the results of a detailed statistical microscopic examination of the ore and the mill products of the Silver King Coalition Mines Co., Park City, Utah.The study was conducted under the joint auspices of the United States Bureau of mines is cooperation with the University of Utah at Salt Lake City, Utah. The work was done in the cooperative Microscopic Service Laboratory, which was equipped by contributions from the following companies: Utah Copper Co., International Smelting & Refining Co., American Smelting & Refining Co., United States Smelting, Refining & Mining Co., Tintic Standard Mining Co., Silver King Coalition Mines Co., and Park Utah Consolidated Mines Co. The salaries and the other costs involved in operation of the laboratory were met by contributions from certain supporting companies. In addition to the regular personnel of the laboratory the Bureau of Mines contributed the part-time services of a microscopist-consultant to direct and assist with the technical work.ACKNOWLEDGEMENTSThe authors acknowledge the courtesies extended by the Silver King Coalition Mines Co., through its general manager, M. J. Dailey, in furnishing the various ores and products on which the study was made, together with general information concerning the problems encountered or recognized in connection with the milling of the Silver King ore."

Jun 1, 1934

By Fred N. Kissell

This handbook describes effective methods for the control of methane gas in mines and tunnels. It assumes the reader is familiar with mining. The first chapter covers facts about methane important to mine safety, such as the explosibility of gas mixtures. The second chapter covers methane sampling, which is crucial because many methane explosions have been attributed to sampling deficiencies. Subsequent chapters describe methane control methods for different kinds of mines and mining equipment, primarily for U.S. coal mines. These coal mine chapters include continuous miners and longwalls, including bleeders. Coal seam degasification is covered extensively. Other coal mine chapters deal with methane emission forecasting and predicting the excess gas from troublesome geologic features like faults. Additional coal chapters contain methane controls for shaft sinking and shaft filling, for surface highwall mines, and for coal storage silos. Major coal mine explosion disasters have always involved the combustion of coal dust, originally triggered by methane. Thus, a chapter is included on making coal dust inert so it cannot explode. Methane is surprisingly common in metal and nonmetal mines around the world, as well as in many tunnels as they are excavated. Accordingly, a chapter is included on metal and nonmetal mines and another on tunnels. Proper ventilation plays the major role in keeping mines free of hazardous methane accumulations. The ventilation discussed in this handbook, except for the chapter on bleeder systems, deals only with so-called face ventilation, i.e., ventilation of the immediate working face area, not ventilation of the mine as a whole. The omission of whole-mine ventilation was necessary to keep this handbook to a reasonable size and because a huge amount of excellent information is available on the subject.2

Jan 1, 2006

By R. E. Heithecker

In Kansas, almost every oil well drilled into a limestone formation is treated with hydrochloric (muriatic) acid upon completion. This is done to increase the potential capacity of the well and thereby increase its "daily allowable" production (see p. 9), to shorten the time required to produce the recoverable oil, and to increase the quantity of oil recovered ultimately from the reservoir. The porosity and. permeability of limestone formations seldom are uniform throughout the proved area, consequently the production capacities of completed wells vary considerably. Acid treatment of wells tends to increase production capacity and to equalize potential capacity. If offset wells already have been treated with acid, new wells usually are treated to protect the property on which they are drilled against drainage. Even though competitive conditions do not exist in a field, it

Jan 1, 1939

By MINE SAFETY BOARD

RECOMMENDATIONS OF THE UNITED STATES BUREAU OF MINES ON CERTAIN QUESTIONS OF SAFETY AS OF FEBRUARY 3 , 1933

Jul 1, 1933

By E. H. Burroughs

This bulletin is the sixth in the series of petroleum bibliographies published by the Bureau of Mines, Bulletins 149, 165, 180, 189, and 216 being compilations for the years 1915, 1916, 1917, 1918, and 1919- 1920, respectively. In this bulletin the same general plan has been followed in arranging the references, but one or two additions have been made in the classification.

Jan 1, 1921

By G. L. Mowrey, S. D. Maksimovic

An important element of the U.S. Bureau of Mines (USBM) mining research program is the development and evaluation of reliable coal interface detection (CID) systems. Commercially available CID sensors based on natural gamma radiation (NGR) are only applicable if the immediate roof is composed of shaley material. The USBM has made numerous underground and laboratory measurements using several NGR systems approved for installation on mining machines by the Mine Safety and Health Administration. In addition, two small handheld NGR instruments were used to make comparative measurements. Underground NGR measurements in 10 different coal seams, potassium-uranium-thorium radiometric analyses on samples from 16 seams, and chemical analyses of coal and rock for correlation with NGR counts were made. Laboratory test results on the effect of air gap and sample thickness, size, and weight on the NGR measurements, as well as general results of the various NGR systems, are discussed.

Jan 1, 1995

By A. L. Engel

This report is a compilation of results of preliminary tests on scheelite (tungsten) ores and tailings. These investigations were made to assist in establishing satisfactory treatment methods for small-scale concentrator operations, or to indicate a. method for conserving previously lost mineral values in old tailings, if possible. A discussion of test procedures is included, as it was felt that this would add to understanding the results reported under the several projects. The treatment of scheelite ores has become more or less standardized. Important differences occur in textures of ores from various mining districts. However, and this must be considered when planning ore-dressing operations. In most of the present investigations, only a limited amount of work was done, usually just enough to answer a specific question in regard to a particular ore or concerning local conditions. Two methods of treatment included gravity concentration, magnetic separation, and flotation.

Jan 1, 1952

By E. R. Andersen, F. E. Block, T. T. Campbell

This work was done to develop methods for increasing the yields and purity of vanadium prepared by bomb reduction of vanadium compounds . Compounds reduced were V₂ 05 , V203 , VC , and VC13 . Sodium , calcium , and magnesium were used as reductants . Variables considered included reductant form , bomb size , pressure during reaction , method of ignition , and the use of slag fluidizing additives . It was concluded that yields of 85 to 90 percent can be effected by the calcium reduction of V205 in reactors measuring as much as 14 inches in diameter and 60 inches in height . Optimum charge composition included V₂05 , 65 percent excess calcium , and 0.4 moles sulfur per mole vanadium . Purity of the vanadium produced in large reactors varied from 99.5 to 99.8 percent . The higher purity metal , depending upon the amounts of interstitial impurities present , was usually cold ductile . Although high yields of up to 99.5 percent can be effected by bomb reduction of VC1 , the high pressures developed in the bombs and attack of the reactor walls by the byproduct chloride slags discourages this method of preparing vanadium . It was found that significant purification of impure regulus metal occurred when it was hydrided , crushed , acid leached , and vacuum dehydrided . Metal so treated can readily be converted to ductile sheet . A cost estimate based on the production of 100 tons of vanadium per year was prepared . It was concluded that pure ductile vanadium could be produced for approximately $ 20.00 per pound .

Jan 1, 1964

By Michael Schmitz, Eugene Ahrenholtz, William A. Heitbrink, Jeanne A. Zimmer, Andrew B. Cecala, Ernest S. Moyer, Earle H. Andrews, Chris C. Coppock, John A. Organiscak

Many different types of surface mining equipment use enclosed cabs to protect equipment operators from health and safety hazards. The overburden removal and mining process can be extremely dusty and can cause excessive dust exposure. To study this issue, a cooperative research effort was established between the National Institute for Occupational Safety and Health, U.S. Silica Co., Clean Air Filter Co., and Red Dot Corp. in an effort to lower respirable dust levels in an enclosed cab on an older surface drill at a silica sand operation. Throughout this research effort, a number of modifications were incorporated into the drill's filtration and pressurization system, as well as in other areas, to improve its design and performance. An average cab efficiency of 93.4% was determined with gravimetric sampling instruments when comparing the outside with the inside cab dust levels on the final design. Although this study considered just one operation, the goal was to identify cost-effective improvements that could be implemented on all types of enclosed cabs to lower respirable dust concentrations. Two critical components for an effective enclosed cab system are having a properly designed, installed, and maintained filtration and pressurization system, along with a method for maintaining structural cab integrity, which allows the cab to be positively pressurized. Another important component is maintaining cab cleanliness. Although this research was originally directed toward the mining industry, it is also applicable to agricultural or construction equipment.

By D. L. Soreck

The hazards to the public posed by abandoned mine shafts are well documented. As private development encroaches on previously mined areas, the potential for fatalities and serious injuries from abandoned mine shafts increases. The U.S. Bureau of Mines has conducted research into cellular concrete as a material for sealing these openings. The current work involves testing the characteristics of cellular concrete before and after it had been pumped or dropped from different heights into a simulated mine shaft. Cellular concrete was pumped vertically up to and subsequently dropped from heights of 18 and 37 m into concrete forms. Wet density measurements were made at multiple sampling points in the test circuit. Air content determinations and uniaxial compressive strength testing were conducted. Research results showed significant loss in air content and changes in the characteristics of cellular concrete during pumping or dropping from various heights. Recommendations on effective use of cellular concrete for sealing abandoned mine shafts are made.

Jan 1, 2010

By George J. Conroy

This Bureau of Mines report summarizes the results of a study of mine inspection records covering 2,200 mining installations over a 3-year period ending December 1974. Tables show the relative frequency of violations of certain provisions of the Coal Mine Health and Safety Act of 1969 in particular areas of concern, such as circuit breakers, grounding, and permissibility. Examples of past use of the data and analyses are presented.

Jan 1, 1976

By James Noll, Sam Janisko

Underground miners are exposed to some of the highest levels of diesel particulate matter (DPM) in the United States. Therefore, it is important to monitor the exposure of miners to DPM, but it can be difficult because of the complex composition of DPM and the number of interferences. Currently, elemental carbon (EC) is used as a surrogate because it makes up a significant fraction of the DPM and is not affected by interferences. Standard measurement methods for EC can be time consuming and only record end of shift results. In this research, a laser absorption technique that enables one to measure EC concentration in near real time was shown to be a beneficial tool. The real time data showed that the fresh air being drawn into a stone mine was not properly reaching the working area and needed to be redirected to decrease DPM concentrations. The real time data also provided a more accurate efficiency ofan environmental cab compared to just using the standard method by detecting the opening of the cab's window and door. The EC optical monitor was also worn by researchers in a mine to show how it can give not only the average concentration for the shift but also reveal when and where a miner is exposed to DPM. Keywords: Laser absorption, diesel, elemental carbon, mining, exposure

By Robert W. Van Dolah

The prevention of fires and explosions involving the combustibles and oxidants likely to be found in flight vehicles requires a knowledge of the flammability and related characteristics of these materials. This circular is a compilation of the available charactersilics data for a series of combustibles and oxidants of current interest. Vapor pressure data are presented for fluorine, oxygen, chlorine trifluoride, nitrogen tetroxide, nitric acid, hydrogen peroxide, ethylene oxide, hydrogen, ammonia, pentaborane, unsymmetrical dimethylhydrazine, monomethylhydrazine, hydrazine, and a series of hydro-carbons including decalin, tetralin, bicyclohexyl and other high-density fuels. In addition, flammability characteristics diagrams are included for each of the fuels in contact with air and, where available, other oxidants (for example, oxygen and nitrogen tetroxide). To assist in understanding these data, sections on definitions and theory and applications have been included. Each section is complete in itself and can be used separately. For example, a reader who is familiar with the general theory of combustion and detonation may find the data sections more useful than the definitions and theory and the application sections. However, since pertinent data are included in these sections, they should also prove useful to the experienced engineer interested in preventing fires and explosions.

Jan 1, 1963

By Dean. R. S.

The work of the copper metallurgy section during the year was devoted to laboratory studies of sulphur recovery from smelter smoke and combination smelting of copper and manganese. Both of these subjects were new this year. Combination Smelting of Copper and Manganese According to published work, the affinity of manganese for sulphur is greater than that of iron for sulphur, so that if a suitable mixture of com-pounds of iron, copper, and manganese be smelted to form a matte and slag, manganese should concentrate in the matte, together with copper.

Jan 1, 1937