Search Documents

The concept of isokinetic measurement of strength was originally related by Hislop and Perrine.(1)Characteristics of an isokinetic exertion are constant velocity throughout a predetermined range of motion. Strictly speaking, a means of speed control, and not a load in the usual sense, is applied in isokinetic exertions.(1)However, load and resistance are definitely present in this technique. In this case, the load is a result of the energy absorption process performed by the device to keep the exertion speed constant. The device prevents energy from being dissipated through acceleration in isokinetic exercise. The energy is instead converted into a resistive force, which varies in relation to the efficiency of the skeletal muscle. Since the speed of motion is held constant in isokinetic exercise, the resistance experienced during a contraction is equivalent to the force applied throughout the range of motion. For this reason, the technique of isokinetic exercise has sometimes been referred to as accommodating resistance exercise. This type of exercise allows the muscle to contract at its maximum capability a tall points throughout the range of motion. At the extremes of the range of motion of a joint, the muscle has the least mechanical advantage, and the resistance offered by the machine is correspondingly lower. Similarly, as the muscle reaches its optimal mechanical advantage, the resistance of the machine increases proportionally. It must be understood, however, that while isokinetic devices control the speed of the exertion, this does not assure a constant speed of muscle contraction. The speed of isokinetic contractions is constant during individual exertions; however, it is also possible to compare muscular performance over a wide range of isokinetic velocities. Increasing the isokinetic speed of contraction will place increasing demands on Type II muscle fibers (fast twitch and fast oxidative glycolytic). Workplace Assessment It is clear that isometric strength testing cannot substitute for dynamic strength assessment when examining highly dynamic occupational job demands. As most industrial work tasks contain a significant dynamic component, analysis of isokinetic strength capabilities appears to offer some advantage to isometric testing in this regard. However, it must be recognized that isokinetic devices are not entirely realistic compared with free dynamic lifting in which subjects may use rapid acceleration to gain a weight-lifting advantage.

Jan 1, 1998

By K. Shimamoto

This study has been prompted by the anticipated demand for rhenium by the petroleum industry and the concern for an adequate supply of rhenium to meet the demand. The present and projected outlook for rhenium relative to its distribution and occurrences, the recovery factors involved in ore beneficiation, capital and operating costs, changing technology, and the projected uses and market growth of rhenium are presented in this report as part of the Bureau of Mines program to determine the availability of recoverable rhenium in a developing market.

Jan 1, 1973

By D. D. Walker

Scheelite, the most abundant tungsten mineral in the Philipsburg region of Montana, is found in replacement deposits and along fissures and cracks in limestone at various distances from contacts with acidic igneous rocks. It also occurs at the limestone-igneous contacts, but typical garnet tactites are developed in only a few places in the region. The most favorable host rocks for scheelite mineralization are the Jefferson, Hasmark, and Madison limestones. Scheelite is exposed in float, outcrops, and surface and mine workings along a 2-mile-wide belt extending southwest from Lost Creek beyond Silver Lake, a distance of 15 miles or more. (See fig. 1.) Some scheelite is found in veins formerly mined for silver. Powellite and molybdenite occasionally are present with the scheelite. Hubnerite occurs in quartz veins in the Black Pine area 10 miles northwest of Philipsburg. These quartz veins occur in the quartzites of the Precambrian Spokane formation. Tungsten production in the region has come almost exclusively from scheelite deposits, both lode and placer. During a 6-year period beginning in 1943 a total of 142.0 tons of 63-percent W03 concentrate was produced by H & H Mines Co. In the early 1950's, the Trigger mine produced 4,000 tons of 1-percent W03 ore and the Tip Top 650 tons of 2.0-percent W03 ore and 2,906 tons of 2.2-percent ore. There has been sporadic production from some of the smaller properties in the area.

Jan 1, 1960

By John C. Machisak

STATISTICAL data on injuries and employment pertinent to metal mines and to their mills, and/or processing plants are presented in this Information Circular for the calendar year 1960. The information pertains to metal mines, as well as ore-dressing plants and primary nonferrous smelters, refineries and reduction plants, and their auxiliary works. These data are voluntarily submitted annually to the Bureau of Mines by the operators, and contribute greatly toward the promotion of safety in the mineral industries. The data presented are classified according to the principal mineral produced and include information on copper, iron, lead-zinc, gold-silver lode, gold placer, uranium-vanadium and miscellaneous metals. A breakdown of miscellaneous metals by commodities is shown in table 19, page 41. The data also relate to workers engaged in production, exploration, development, construction, and maintenance and repair work, as well as supervisory personnel and office- workers at the mine or plant site. Injury and employment data at metal mines and metallurgical plants in the United States for 1960 are shown under the following general sections:

Jan 1, 1963

By E. R. Maize

This report is the second of a series on roof movement in coal mines. The first (R. I. 3355)4/ dealt with convergence of roof and floor and movement of the surface accompanying and following extraction in a mechanized mine in which retreat of rib lines was rapid. The studies reported herein were made in a mine in which all the coal is loaded by hand, and movement of the rib lines was much slower in consequence. In choosing a site for this work, it was decided that the mine selected should have natural conditions akin to those of the first study and entirely different methods of working. To this end a cooperative agreement was made with the Crucible Fuel Co. through W. J. Whitaker, secretary, for conducting the work in the company's Crucible mine, operating in the Pittsburgh bed in Greene County, Pa. This paper gives an account of the methods used in the investigation, excerpts from the data obtained, and such generalizations as can be made.

Jan 1, 1939

By Bruce I. Thomas

As a part of the United States Department of the Interior program for developing natural resources in Alaska, the Bureau of Mines studied the tin-bearing gold-placer deposits in the Tofty area of the Hot Springs district in central Alaska. The principal objective of the Bureau's work was to obtain facts about the extent and character of the placer deposits (including tailing) to indicate the economic or strategic tin-production potential of the Tofty "tin belt." A secondary objective was to determine (if possible) the bedrock Source of the cassiterite and other minerals found in the placer deposits. The placer phase of the work was begun in July 1954 and was continued during the 1955 and 1956 field seasons. Extensions to, and connections between, known placer channels were sought by 82 churn-drill holes. The Bureau drilling did not expand the placer deposits beyond the limits established by drift-mining operations and by previous drilling done by private concerns.

Jan 1, 1957

By John C. Machisak

STATISTICAL data on injuries and employment pertinent to metal mines and to their mills, and/or processing plants are presented in this Information Circular for the calendar year 1960. The information pertains to metal mines, as well as ore-dressing plants and primary nonferrous smelters, refineries and reduction plants, and their auxiliary works. These data are voluntarily submitted annually to the Bureau of Mines by the operators, and contribute greatly toward the promotion of safety in the mineral industries. The data presented are classified according to the principal mineral produced and include information on copper, iron, lead-zinc, gold-silver lode, gold placer, uranium-vanadium and miscellaneous metals. A breakdown of miscellaneous metals by commodities is shown in table 19, page 41. The data also relate to workers engaged in production, exploration, development, construction, and maintenance and repair work, as well as supervisory personnel and office-workers at the mine or plant site. Injury and employment data at metal mines and metallurgical plants in the United States for 1960 are shown under the following general sections: 1. General injury experience: Tables I-5-Data on injuries, injury-frequency and severity rates and related employment data, work location, and degree of injury.

Jan 1, 1963

By N. A. Eilertsen

Among the numerous Low-grade manganese deposits in eastern Aroostook County, Maine, the Dudley deposit near Mapleton in the northern district is one of the few known to contain an appreciable tonnage averaging above 10 percent manganese. The ore body, consisting of stratified manganiferous hematitic shale, is over 5,000 feet long and ranges in width from 30 to 175 feet. The deposit was extensively explored during 1942-44 by the Manganese Ore Co., a subsidiary of M. A. Hanna Co. of Cleveland, Ohio. Data obtained from this work were made available to the State and Federal Geological Surveys for estimating ore reserves. An estimate by the Maine Geological Survey, using a 10-percent manganese cutoff and to a depth of 200 feet, shows 609,000 long tons of manganese metal in material averaging 12.6 percent manganese. By lowering the cutoff limit to 5 percent manganese, the estimate was increased to 919,000 long tons of metallic manga¬nese in material averaging, 10.4 percent manganese,

Jan 1, 1957

By G. L. Oldright, F. S. Wartman

"In the process of smelting copper ores and secondaries in the reverberatory furnace to produce a copper matte and a slag low enough in copper content to be discarded on the dump, it is essential to the best functioning of the process that most of the iron in the material charged into the furnace be at the end in the form of sulphide in the matte or ferrous oxide in the slag. Ferric oxide and magnetite present in the charged material should be reduced to ferrous sulphide or oxide. Ferric oxide offers no difficulty in reduction, at least to the magnetite stage, because it reacts very readily with sulphides at quite low temperatures. Magnetite is less reactive and consequently more resistant to slagging, so that the furnace man must take advantage of all factors favoring its reduction in order to prevent accumulations in the furnace.In order to determine these factors more definitely, the Bureau of Mines in cooperation with the Department of Metallurgy, University of Arizona, has undertaken at the Southwest Experiment Station an investigation of the effect of various factors upon the rate of reduction of magnetite by ferrous sulphide. A previous paper's reported the nature of the reactions taking place and the effect of various physical factors when only pure sulphide and oxide were present. Since in the actual smelting operation, many other substances are also present, it seemed desirable to make a study of the effect of their presence upon the rate of reduction of magnetite by ferrous sulphide. Such a study has been made; the work done and the results obtained are described herewith.As will be shown later, it has been found that of the substances usually present in the smelting charge, silica and magnesia accelerate, whereas lime, alumina, and cuprous sulphide hinder the reduction of magnetite by ferrous sulphide.No report of a previous laboratory investigation of this subject has been found. Almost all furnace operators have made at one time or another at least qualitative ccmparisons of the effect of various changes in operating oonditions upon the behavior of magnetite in the furnace, but the conclusions derived from the experiments have never been published."

Mar 1, 1931

By K. K. Kelley, W. W. Weller

Heat capacity measurements of akermanite ( Ca,MgSiO ) , cordierite (Mg2A14 Sig018 ) , gehlenite ( Ca₂Al₂ SiO ) , and merwinite ( Ca ,MgSiO ) were conducted over the temperature range from 50 ° to 298.15 ° K. The entropies at 298.15 K ( expressed in cal / deg mole ) were evaluated as follows : Akermanite , 50.0 ± 0.5 ; cordierite , 97.3 ± 0.9 ; gehlenite , 47.4 ± 0.4 ; and merwinite , 60.5 ± 0.5 . All four compounds have positive entropies of formation from their constituent oxides at 298.15 ° K ; the values range from 4.6 cal /deg mole for akermanite to 10.1 cal / deg mole for cordierite .

Jan 1, 1963

By Wilton Johnson

Native asphalt was produced by three companies in two States, Texas and Utah. Bituminous limestone, used primarily as a paving material for street and road repair, was produced by one firm, R. L. White Co., Uvalde County, TX. Gilsonite, a solidified hydrocarbon found only in Colorado and Utah, was mined by two firms, American Gilsonite Co., a division of Chevron Resources Co. (a subsidiary of Standard Oil Co. of California), and Ziegler Chemical and Mineral Corp. Hydrocarbon Mining Co. (a subsidiary of Oberon Oil Inc., a Utah corporation) closed its mining operation during the year.

Jan 1, 1988

By George S. Rice

In response to numerous requests for information as to the status of internal-combustion mine locomotives of the Diesel type that use heavy or non- volatile oil for fuel, with special reference to their safe use in coal mines, the United States Bureau of Mines is issuing this report. Data mere obtained, on application of such locomotives to cod mining only in Belgium, France, Germany, and Great Britain. The locomotives are used in coal mining in other countries, as well as in potash, iron, and other kinds of mining, but their chief development has been in coal mining in Germany, France, and Belgium. Recently popular interest in the Diesel type of engine for motive purposes was aroused in this country by the successful application of Diesel engines to railroad locomotives hauling fast transcontinental trains, and, according to published statements, at a low cost of fuel per mile of run.

Jan 1, 1936

By V. A. Cammarota

In this report, the effects of anode-production variables, such as aggregate coke sizes, pitch binder content, and baking cycle, were investigated. A small alumina reduction cell proved effective in evaluating anodes prepared from commercial materials and from lignite coke and pitch. Compressive strength was found to be the physical property most significantly influenced, but it did not appear to affect anode consumption. Specific carbon consumption, that is, the ratio of carbon in the anodic gas to carbon theoretically oxidized at the anode, was used as an index of anode consumption. It was found that an anode made with lignite coke and commercial pitch was very low in consumption; however, anodes made completely from lignite but by a different fabrication method showed high consumption and anode deterioration. Microscopic examination of anodes after electrolysis showed evidence of higher consumption at low current densities, and was useful in judging overall anode quality. Based on the physical properties of the anodes and their consumption during electrolysis, lignite can be a suitable material for anodes, provided the proper fabrication conditions are used.

Jan 1, 1970

By Yael Miron

This report describes laboratory studies by the U.S. Bureau of Mines to determine the suitability of a static oxygen (OJ adsorption test for evaluating the self-heating tendencies of coals. Reliable minimum self-heating temperature (SHT) values from adiabatic oven tests were used as standards for comparison and evaluation. A suite of six coals was tested in the adiabatic oven and in sealed flasks. In the latter tests, both undried and dried samples, in a range of four particle sizes, were examined. Miniature pressure trans-ducers monitored pressures in the flasks, and gas samples taken at the end of the tests quantified all the gases present. An excellent correlation was found between the minimum SHT's and amounts of O2 adsorbed over a 7-day period for dried coals, independent of particle size. In addition, a good correlation was obtained between the minimum SHT's and pressure changes in the flasks at the end of the test for the same coals, also independent of particle size. Based on these results, the sealed flask test can be reliably used to determine the self-heating tendency of a bituminous coal sample.

Jan 1, 1990

By Larman J. Heath

Wellbore enlargement was tested using hydrazine hydrate in a gas-storage well in Ohio to increase the well productivity. The wellbore was to be enlarged by chemical disaggregation of the sandstone adjacent to the wellbore. Productivity immediately declined 49.1 percent and gradually declined to zero in 7 months. A down-hole camera survey showed a white-to-gray precipitate covering the entire wellbore surface. The precipitate was chemically analyzed and identified as mostly carbazic acid, a hydrazine derivative of carbonic acid. Formation of this precipitate was not anticipated; this viscous sub-stance caused the gradual loss in productivity of the well. The wellbore was not enlarged. Laboratory tests were run to determine what clay stabilization measures could be taken in sandstone cores to prevent clay swelling and particle migration caused by hydrazine hydrate. Normal clay stabilization methods did not prevent the virtually complete loss in permeability to hydrazine hydrate. Other laboratory tests using natural gas diluted with small amounts of carbon dioxide confirmed the ease with which carbazic acid could be formed in a hydrazine hydrate-saturated environment within and adjacent to the wellbore.

Jan 1, 1970

By David A. Summers

Coal is increasingly viewed as one of the major fuel resources of this country for the remainder of this century. The need to extract a greater percentage of the coal in a given seam, together with advantages of improved safety, indicates that longwall mining will become more widely used within this time frame. A novel method of mining coal on a longwall face, utilizing high pressure water jets, is herein described. The mining machine proposed will exploit the stress conditions which exist on a longwall panel in order to achieve the required productivity while at the same time reducing respirable dust and methane ignition hazards. The water jets will excavate only the boundary of the extracted seam section, and thus the energy requirement of the machine will be minimized. The action of the machine is similar to that of an existing coal plow, except in that the wedge teeth of the plow are replaced by oscillating high pressure water jets. The machine can, therefore, cut to the depth and at the speed of existing shearer units at equivalent power levels. The removal of impact stresses from the machine will reduce downtime required for maintenance and replacement of picks and lower the load on the haulage motor of the system. The ability of the machine to increase the depth of cut without an increase in horsepower will further improve productivity when transportation systems to remove the greater production are in operation.

Jan 1, 1974

By George S. Rice

In response to numerous requests for information as to the status of internal-combustion mine locomotives of the Diesel type that use heavy or nonvolatile oil for fuel, with special reference to their safe use in coal mines, the United States Bureau of Mines is issuing this t port. Data were obtained on application of such locomotives to coal mining only in Belgium, France, Germany, and Great Britain. The locomotives are used in coal mining in other countries, as well as in potash, iron, and other kinds of mining, but their chief development has been in coal mining in Germany, France, and Belgium. Recently popular interest in the Diesel type of engine for motive purposes was aroused in this country by the successful application of Diesel engines to railroad locomotives hauling fast transcontinental trains, and, according to published statements, at a low cost of fuel per mile of run.

Jan 1, 1936

By Edwin C. Reeder

This paper, describing milling methods and costs at the Hillside Fluorspar Mines at Rosiclare, Ill., is one of a series being prepared for and published by the United States Bureau of Mines on non-metallic milling methods. The milling practice described is that of one of the large mines in the Kentucky-Illinois fluorspar field in southern Illinois and western Kentucky, on the Ohio River. Milling methods throughout the district are similar in their general principles, although details vary considerably in different plants.

Jan 1, 1932

By John R. McDonnell

The Valle Vidal Unit comprises 100,000 acres In Taos and Colfax: Counties, New Mexico. The unit was donated to the American public In 1982 by the Pennzoll Co. and is administered by the U.S. Department of Agriculture Forest Service as an addition to the Carson National Forest. During 1990-1991, the Bureau of Mines conducted a mineral Investigation of the unit as authorized by an Interagency Agreement (1987) Intended to assist the Forest Service to incorporate mineral resource data In forest plans. The Bureau reviewed literature and records concerning mineral resources and mining activity, and performed a field examination of mines, prospects, and mineral occurrences in and near the Valle Vidal Unit. The La Belle mining district encompasses most of the western part of the Valle Vidal Unit. The district was most active between 1893 and 1902, after the land grant was opened to prospecting and gold discoveries were reported. The discoveries were low grade, and eventually were abandoned. The Bureau's appraisal of the district determined that lode gold occurs primarily in fissure veins in volcanic rocks, and placer gold occurs In weakly cemented sedimentary rocks and alluvial sediments; but at a grade that is currently considered subeconomic. If the price of gold increases in the future, prospecting and exploration in the area may be renewed, but the activity would likely be limited due to "acquired land status" restrictions, which require mineral leasing and prohibit claim location in the Valle Vidal Unit.

Jan 1, 1992

By L. W. Higley

It is estimated that well over 20 million lb of chromium and 8 million lb of nickel, plus other metal values, are diverted annually to furnace dusts, mill scale, and contaminated swarfs in the domestic stainless and other specialty steelmaking industry. Little inroad has been made toward the in-plant recycling of these wastes to reclaim the metal values. The Bureau of Mines has devised a process for recovering about 90 pct of the chromium and molybdenum and well over 90 pct of the nickel and iron from stainless steelmaking furnace dusts, swarf, and mill scale. Other metals such as manganese are also recovered. Initial laboratory results were confirmed and expanded to include a wide variation of stainless steelmaking waste mixtures. Later experiments have included specialty steelmaking wastes other than from stainless steelmaking. Significantly, the ease of technology transfer has been demonstrated by a number of industrial-sized (19-ton) commercial electric furnace heats, in which the pelletized wastes represented some 10 to 20 pct of the furnace charge, replacing part of the normal scrap charge. Results of these successful large-scale trials are presented. Some information is also presented on incorporation into the pellets of chromium-bearing particulate wastes originating from other than steelmaking production. Cost evaluation indicates the process is economically attractive.

Jan 1, 1982