Search Documents

By Joe Strobbe, Kevin Joe

The U.S. Bureau of Reclamation awarded PCL Civil Constructors the project to build a new visitor's center and parking lot structure at the Hoover Dam. The excavations for these structures present many blast design challenges. The visitor center, a 30 foot deep excavation was blasted in the Nevada side of the canyon wall, 600 feet above the existing power plant. This excavation also included a through-cut underneath the existing road that carries the traffic over the Dam between Nevada and Arizona.

Jan 1, 1993

By Bruce B. Redpath, Thomas E. Ricketts

Scaling laws commonly used for describing or predicting blast motions generated by conventional arrays of blastholes are dimensionally incorrect. The scaling of distance by the cube root of charge weight is correct only for spherical charges, and scaling by the square root of charge weight is incorrect for any charge configuration, although both approaches may result in empirically useful formulas for a limited range of charge sizes. Analysis of motions generated by a large set of underground blasts shows that scaling distance by the square root of the linear charge density, which is dimensionally correct for a cylindrical borehole, yields much more consistent results than the traditional scaling rules. Further, this scaling law is valid right up to the free face of the burden. A significant result of this work is that the peak particle velocity for an array of blastholes is primarily dependent on blasthole diameter and not on total charge weight or maximum explosive weight per delay, which are the commonly used parameters for scaling seismic amplitudes generated by conventional blasting arrays.

Jan 1, 1987

By Robert Hopler

On June 13, 1912, the final decree of dissolution of the DuPont explosives trust was handed down, and the resulting new companies began operating at the beginning of the new year. The property assets granted to (or retained by) the companies were as follows:

Jan 1, 2014

By Sandy Tavelli, Thomas L. Barkley

This discussion will present a case study in developing solutions to a metropolitan quarry’s public relations, legal, environmental, and productivity problems. It details an extensive and detailed project to address the blasting practice in a medium sized quarry that is surrounded by residential and industrial zones. The principle work was done over a four-month duration during the normal production season. It included detailed drilling and blasting audits for baseline information. In addition, geologic characterization, seismic modeling, correction of deviations from best practices, and implementation and monitoring of precise electronic timing to provide dramatic solutions for the quarry. The quarry is in the near suburbs of a large metropolitan city. It is framed on two sides by residential municipalities and on two sides by industrial zones. At the start of the project, the quarry was in court as a result of the lawsuit by one of the neighboring towns that was suing to close the quarry. The lawsuit had progressed to the advanced stage where in the Judge had appointed an arbitrator to make the decision of continued operation. This arbitrator was to observe our progress and recommend to the Judge the disposition of the case.

Jan 1, 2004

By Thomas P. Dowling

Since the 1950's, blasting practices have undergone many revolutionary changes. Some of the more radical departures have involved, in addition to high speed drilling equipment, a myriad of new explosives, blasting agents, boosters, initiators, initiating systems and delay devices. The introduction of ANFO in the mid 1950's as a blasting agent seems to have instigated a trend toward the development and use of less sensitive blasting agents. The evolution of slurries or water gels has produced dense, high strength, water resistant products which has further promoted this trend away from the more sensitive, conventional explosives.

Jan 1, 1975

By Patrick Cahill, Jacob Miller, Nolan Mundwiller, Catherine Johnson

"The Experimental Mine at the Missouri University of Science and Technology is undergoing major developments. The underground workings are being expanded to include a ramp down to a second level which will comprise of larger opening and room sizes to better simulate modern mine layouts. Thisexpansion will enable the Experimental Mine to be utilized for many more generations. In addition, the new 15,000 sq. ft. Kennedy Mine Building is being constructed and will house the mine office,classrooms, and three laboratories to accommodate the mining and explosives engineering programs’ ever-increasing enrollment. With these new developments come an increasing need for safety and awareness in regards to explosives and blasting. This paper will utilize the Institute of ExplosivesMakers Safety Analysis of Risk (IMESAFR) software tool, to assess current magazine compliance withthe increased personnel limits and mine building location. Furthermore, this paper will assess theimplementation of a wireless blast warning system consisting of warning beacons and a centrally located siren which will be integrated with the construction of the Kennedy Mine Building. This warning system will provide the necessary precautions to safely conduct blasting-related experiential learningopportunities and research projects, and will enable facility staff to more efficiently oversee blastingoperations at the Experimental Mine. "

Jan 1, 2017

By Dennis Wilzbacher, John Wiegand

In an effort to reduce the cost of bulk explosives, Vigo Coal Company found that the addition of coal mined at their Friendsville Mine, not only reduced explosive costs, but also appeared to actually enhance blasting performance. The Friendsville Coal lies at the base of the Mattoon geologic formation within the Mcleansboro Group of the Missourian Series of the Pennsylvanian Geologic System in Southern Illinois. Vigo Coal Company commissioned VIBRONICS, INC., an independent blasting consulting company to quantify actual blasting performance. Insitu sonic velocity testing of overburden was conducted to determine the P-wave velocity of the sandstone present at Vigo’s Cypress Creek Mine, where the initial testing was conducted. Numerous VOD (velocity of detonation) recordings were obtained for varying blends of ANFO/Coal (now named Carbo*Prill). Cast blast percentages were determined for both Carbo*Prill and non coal blended bulk explosive blasts. The VOD of the coal blended product was intentionally reduced so as to more closely match the P-wave velocity of the sandstone overburden. Explosive blends containing as much as 40-50 percent coal were tested. Explosive blends containing greater than 30 percent coal, have been used in Cypress Creek Mine overburden production blasts. The coal blends appear to produce better fragmentation and yield excellent cast blast performance. Safer mining conditions were also observed. Flyrock potential was reduced. The blasts produced less back break, producing a safer highwall. Stripping dozer and shovel production rose during the testing period and equipment repair costs were lowered due to an increase in overburden fragmentation. Blasting vibrations were reduced, in part due to the lowered detonation velocity of the ANFO/Coal mixture. The Friendsville Coal Seam appears to contain inherent chemical and physical properties that enhance blasting performance. The use of Carbo*Prill has been approved by MSHA, BATF, the State of Illinois, and the State of Indiana. This paper will provide details concerning testing procedures, blast performance analysis, recommendations and conclusions for using this alternative blasting mixture.

Jan 1, 2007

By Paul Worsey, Gillian Worsey

Description of Project:The basic blasting class underground lab at the Missouri S&T experimental mine in Rolla, o., shows the students how to drill, set up, load, and shoot a shot underground. In this case the shot was part of a new ramp to a second level.

Jan 1, 2014

By John Wall

The use of electronic detonators in civil tunnelling applications, to reduce vibration is small firings has been successfully utilised for a number of years. As part of the mining industry’s commitment to reducing blast damage during the development cycle in underground mining applications, a series of development blasts using eDevTM electronic detonators in typical mining applications was conducted in North Queensland, Australia.

Jan 1, 2012

By Mario Alvarez

Drilling with tricone drill bits is widely used in the mining industry with a direct impact on drilling safety and costs, however it can be challenging to implement a new supplier of tricone drill bits, choosing a new model of this accessory due to the normal variations of the rock mass or even due to the acquisition of new and modern drilling equipment for open pit blasting operations. This article identifies the most common mechanisms of failure in productive drill holes of tricone drill bits, both in open-pit coal and metal mines, in two South American countries. It also emphasizes the important issues that must be addressed for the optimization of the performance of these accessories, such as the correct identification of the rock mass, the drilling parameters, and the impact of autonomous drilling on new equipment with this technology. The article presents some of the successful actions to economically improve the performance of drill bits considering the close relationship in the field with the supplier's technical representatives and factory designers, as well as the commercial interrelationship between their respective business areas. The article concludes by discussing the future of tricone drill bit design development, its environmental management, and possible new advances in its manufacture.

Jan 21, 2025

By Thomas M. Keevin, Gregory L. Hempen

A study was conducted to measure underwater pressures associated with confined borehole shooting used to remove rock for The Kill Van Kull Deepening Project, U.S. Army Corps of Engineers, New York District. A major natural-resource-agency concern was the potential for fish mortality during explosive rock removal. Currently, fish mortality models are based on testing programs that exposed captured organisms to open-water blasts. Natural resource agencies, without in-house explosive engineering expertise, generally are not familiar with the physical properties of blasting underwater. Confined shots are most often used for demolition and rock removal underwater. Pressure amplitudes from confined blasts are significantly reduced as compared to open-water blasts that, are commonly used for fish testing The duties of natural resource agencies are made even more difficult by the lack of published data on pressures associated with confined blasting. As a result, explosive weights for confined shots mistakenly have been used to run mortality models that were developed using open-water blast pressure data. This study was conducted to collect pressure measurements during rock removal for the KVK deepening project and compare those data with computed peak pressures for open-water explosions.

Jan 1, 2005

By Ruilin Yang

The vector sum peak particle velocity (PPV) of blast vibrations describes the blast vibration intensity more completely than the PPV of a single component waveform. It is more logical to use a vector sum PPV as a vibration limit than using a single component PPV. In 1980 the USBM recommended the frequency related peak particle velocity criterion. So far this method has been only applied to single component waveforms, but not to the vector sum PPV since there is no method available to associate a frequency to the vector sum PPV. The present paper describes a method to define a principal frequency associated with vector sum PPV. The method is based on the weighted average of the principal (zero-crossing) frequencies of the three tri-axial components at the time of the PPV.

Jan 1, 2015

By Cathy Aimone-Martin

The City of Henderson, Nevada is experiencing extraordinary population growth. Some residential development requires blasting to be conducted at close proximities to high-value houses. Blastingrelated concerns voiced by the community residents include dust, noise, fears of damage to residences, and claims of insufficient controls exercised by the blasters. Residents perceive geological conditions are adverse to the protection of structures at the current vibration regulatory limit of 0.5 in/s. Airblast limits are 120 dB. Vibrations felt within structures leave home owners with the perception that damage is taking place. New cracks appearing in homes at distances far from the blasting are being blamed on blasting.

Jan 1, 2007

By Catherine Johnson, Barbara Rutter

The shock tunnel located at the Missouri University of Science and Technology Experimental Mine is 65 feet 9 inches (20.0406 m) in length. The tests performed inside of this tunnel are either arena tests or shock interaction and transfer (SIT) tests. Arena tests simulate a large open air blast, with lower explosive weights, by elongating the impulse of the blast wave. SIT tests are conducted to determine how the produced shock wave interacts and transfers its energy into a target object located at the end of the tunnel. The target used in this research is multilayered, with each layer being a different material. The targets are 2 ft. by 4 ft. (0.6096m by 1.2192m) pieces of Medium Density Fiberboard (MDF), DOW polystyrene foam insulation, and gypsum drywall. The order of these materials varies with each test. This shock tunnel is unique, because the geometry changes along its length. To fully understand how the shock waves are affected by these changes, a working model was needed. The second purpose of this model is to confirm the maximum charge size of 400 grams (14.11 oz.) of C4 that can be detonated inside the tunnel without causing damage to or failure of the tunnel, thus reducing the amount of time needed in downtime and repair. The model predicts pressures in various locations both within the tunnel and the attached target, thus assisting in determining where failures would likely occur. In the process of generating this model, several problems were encountered, including filling the tunnel with air, meshing the complex geometry, and creating the tunnel in a CAD system. This paper will discuss how these problems were solved. A working model was created by using ANSYS Explicit Dynamics and ANSYS Autodyn. The tunnel geometry file was created using SolidWorks and includes the complex geometry changes along with the target and its mount located at the end of the tunnel. The results produced by the model were compared to the field SIT tests. The comparison of the results from both the model and the experimental testing showed a similar trend in the pressure traces.

Jan 1, 2018

By Robert Hopler

SECTION 9.---BORING AND BLASTING.*155. Blasting is the operation of bringing down and detaching from its bed or position masses of material by means of explosives.

Jan 1, 2011

By Hideaki Kitajima, Daisuke Fukuda, Kazuma Moriya, Katsuya Sasaki, Katsuhiko Kaneko

The purpose of this research is to analyze the fracture process and achieve design optimization of a splitting method for concrete and rocks termed the electric discharge impulse crushing method (EDICM). The EDICM utilizes the cartridges being set in boreholes in the splitting target. The cartridge has a thin metal wire and is filled with nitromethane. By applying the electric discharge to the wire in the cartridge, plasma is caused leading to the vaporization of the wire. Then the deflagration of the nitromethane commences, which generates borehole pressure for splitting the target. Although the required splitting time is roughly several hundred micro-seconds and much slower than ordinary blasting, the fracturing still completes in quite short time and understanding the fracture process of opaque and brittle materials such as rock and concrete in this time scale is of academic importance.

Jan 1, 2011

By Johan Gjødvad, Catherine Aimone-Martin, Charles Dowding, Mathias Jern

A residential structure adjacent to a quarry in Ohio was instrumented to record structure motions, resulting wall strains and existing crack displacements in response to close-in blasting within 82 m (270 ft). The project is a cooperative effort among international experts representing the European Federation of Explosives Engineers (EFEE) and ISEE supported by more than 21 persons from eight different countries to compliment prior work performed at the Aitik Mine in northern Sweden. The focus of this study is to compare blast-induced vibration measurements relative to regulatory compliance limits as a percentage of allowable velocities among eight different countries for a one-story residential wood-frame structure with a brick-and-mortar exterior and full basement. Participating counties included Austria, France, Germany, Norway, Sweden, Switzerland, the United Kingdom (UK) and the United States (US). Geophones were placed on the foundation and in the ground in accordance with each country’s regulations to record peak velocities as a function of frequency or distance to blasting. This study extends the work performed at the Aitik Mine to include interior corner geophones to calculate global wall strains and micro-m (micro-in) displacement gauges mounted over an existing drywall crack to measure blast-induced dynamic crack responses and climatological influences on daily opening and closing of a crack. Structure responses were documented for 68 blasts conducted north of the structure from February through September 2023 of which 17 blasts were selected for detailed analyses. The highest in-ground PPVs recorded were 43 mm/s and 59 mm/s at the NE and SW corners, respectively. Measurements from these blasts plotted within each country’s limits provided a comparison of stringency among the counties. The percentage of compliance limits among counties ranged from an average of 114% for the US, UK, and Austria limits to the highest of 585% for Switzerland. Despite these high percentages of compliance for all countries, the global tensile strains induced by these blasts were at most only 12 μ-strains and occurred with the highest velocity blast that exceeded each county’s limit. This high percentage of compliance and low strain level demonstrates the restrictive nature of the regulations studied. Peak dynamic crack opening and closing during blasting averaged 20 -m (0.0008 in) while the 12-hour weather-induced crack displacement during the time period over which blasting occurred averaged 200 -m (0.008 in) and the largest 12-hr change in crack width was 356 -m. This low level of crack response validates the observation that the studied regulations have highly conservative limits for cracking potential of standard building materials.

Jan 21, 2025

By Christopher Laughton

A new underground laboratory is under construction at the recently closed Homestake Gold Mine, Lead South Dakota, United States of America. The Deep Underground Science and Engineering Laboratory is designed to meet the needs of an international group of scientists and engineers interested in conducting fundamental and applied research at depth in the Earth’s crust.

Jan 1, 2011

By Evan Smart, Andrew Palangio, David Klingspor, Blessing Taiwo

This study presents a DMAIC-based approach to optimize blasting performance and achieve crusher-compatible fragmentation at the Walker-Severn Quarry in Ontario, Canada. By applying the Six Sigma DMAIC (Define, Measure, Analyze, Improve, Control) framework, the study aims to enhance the integration between blasting and primary crushing operations. Several representative blasts will be simulated and evaluated using both aerial and terrestrial image analysis technologies to assess fragmentation characteristics. The investigation was guided by quarry-specific Key Performance Indicators (KPIs), ensuring that blast design modifications were both practical and operationally relevant. Through structured analysis and data-driven refinement of blast parameters, the study reveals how this framework was used to address the quarry production demand for increased crusher throughput, and reduced processing costs. The existing quarry blast design was assessed as a baseline and compared against the crusher's inlet requirements and the acceptable fines level specified by the quarry. This evaluation aimed to identify and implement modifications to enhance blast performance. A drone (UAV) was employed to capture post-blast images and monitor blast pile displacement. These UAV images were used to generate an orthomosaic image, which was analyzed to assess fragmentation. The orthomosaic was overlaid onto a GIS platform using a 10m-by-10m grid to evaluate fragmentation distribution across the bench and identify areas requiring optimization. Additionally, drone imagery was utilized to monitor the impact of each blast on the subsequent blast's free face and to assess energy utilization for optimizing front-row holes to achieve improved fragmentation. The outcomes of this research offer a replicable methodology for continuous improvement in quarry blasting practices, with a focus on producing fragmentation that aligns with primary crusher requirements.

Jan 26, 2026

By Jim Daley

This case history discusses a pre-split test conducted at BHP Mineralss Navajo Mine in Fruitland, New Mexico. The test was an extension of earlier pre-split testing conducted by Virgil Stachura of the U.S. Bureau of Mines in conjunction with Navajo Mine and WESCO Inc. which tested low-density product in 10.625 diameter holes.

Jan 1, 1996