Search Documents

By S. Lim, G. Walsh, V. Romero

The cable television show, Mythbusters, contacted the New Mexico Institute of Mining and Technology requesting a pressure gauge to be used in underwater testing. The requirements for the gauge were: it must be passive (i.e. require no power to function), it must indicate when a certain, pre-determined pressure was reached, and that indication was to be visual. A pressure gauge was developed, using standard, commercially available rupture discs, set to burst at 500 psi. Underwater testing was conducted using a 400 lb Pentolite charge. Test devices were set out at ranges from 50 to 200 feet from the seat of the blast. The rupture discs showed a lethal range up to 100 feet, but not at 150 feet. This result matched well with the behavior predicted through modeling and simple shock physics calculations. Additionally, the geometry between the incoming shock and the pressure gauge did not seem to have a strong effect on gauge performance.

Jan 1, 2009

By Clara Godoy, J. A. Sanchidrian

In this paper, Machine Learning techniques have been used to combine data monitored from the drill rig with scanner profiles of the excavated sections to develop an automatic geotechnical rock mass characterization model able to estimate potential zones of over- or under-break of the remaining rock mass in underground blasting. By comparison of scanner profiles of the excavated sections with the blasthole positions, an Excavated Mean Distance (EMD) between the contour blastholes and the excavated profile has been obtained, which may be considered as damage measure.

Feb 1, 2020

By Tapan Goswami

The main objective of the blasting phase in a coal mining operation is to maximise the coal recovery. However, coal loss due to blasting is a serious problem. The Australian Coal Association Research Programme (ACARP) reported in 2011 that in Australia one in every ten coal mines is completely wasted due to such losses. Coal is either lost in the spoil, largely due to the blasting operation or becomes diluted and cannot be recovered entirely. The major coal loss mechanisms include losses from the coal seam roof, the floor, the front edge and from dilution. Coal damage and loss mechanisms during cast blasting that have been observed by various authors include: •Excessive cast dragging the coal edge in the cast direction. Movements of this nature are oftenassociated with the formation of trenches. •Spatial movement of overburden where rock shears and moves in a plane above the coal seam,which damages and dilutes the coal. •Rock falling over the coal during the blast often producing indentations in the exposed coal. •The inappropriate use of bulk and initiating explosives that often results in coal damage. •Insufficient stand-off distances from the coal. The Australian coal mining industry has gone a long way towards addressing the coal loss issues since 2011: almost all operations now deploy touch-coal drilling and sporadically use gamma logging for loading overburden. A study was conducted to compare the effectiveness of touch-coal information in which some touch-coal blastholes were drilled on a fixed or random pattern. In another study, some blastholes were drilled to the touch-coal, gamma-logged and mapped to determine stand-off distances. It was found that the coal roof surface created by gamma-logged holes was the most effective option for minimising coal loss. As a result, a variable stand-off distance was found to be the key to minimising losses. This paper discusses the importance of coal mapping, the rock properties of the roof and floor interface of the coal seam, and the significance of loading and initiating designs in minimising coal damage. Furthermore, the importance of using electronic initiators cannot be emphasised enough. This paper also discusses how a cast blast can be initiated from many locations by mitigating geological abnormalities and thereby avoiding spatial movement of rock shearing in a plane above the coal seam.

By Tapan Goswami

This paper discusses the importance of coal mapping, the rock properties of the roof and floor interface of the coal seam, and the significance of loading and initiating designs in minimising coal damage. Furthermore, the importance of using electronic initiators cannot be emphasised enough. This paper also discusses how a cast blast can be initiated from many locations by mitigating geological abnormalities and thereby avoiding spatial movement of rock shearing in a plane above the coal seam.

Feb 1, 2020

By Joseph A. Meyers

NYC has always been a high-profile target for both foreign and domestic terrorists. Explosives have always been the go-to tool for terrorists to bring about serious physical injury, death, and property damage in our society. Today with the anti-police movement gaining traction in the United States and anarchists groups using homemade explosives against law enforcement and municipalities, it is the responsibility of the explosives industry to ensure that every explosive product on a blasting site is secure. We must prevent the theft of these energetic materials used on projects and sold by vendors so they are not used by these terrorists. We have learned many lessons here in NYC which began with the theft of explosives used for blasting projects in NYC to supply the IRA (Irish Republican Army) 50 years ago. The liability is too significant to take short cuts in securing energetic materials. Over the years through cooperation with all agencies and the industry we in NYC have developed certain proven protocol and procedures we would like to share with the industry. An efficient and effective security plan for the logistic movement of explosives, as well as for the blast site is imperative to keeping the good name of the industry from negative repercussions and possible additional bureaucratic oversight of an industry that is highly regulated and still recovering from the pandemic. Communication, security assessments and transparency with all stakeholders and the Authority Having Jurisdiction (AHJ) will greatly improve the overall security for the blasting project. This SOP (standard operating procedure) will allow the AHJ to become a proactive partner in the security of the blasting project. If the AHJ is not a law enforcement agency, the law enforcement agency specialty unit must be notified and included in all phases of the project. The security for a blasting project with AHJ and law enforcement input starts at the inception of the project when the memorandum of understanding (MOU) is obtained, and involves the AHJ through all steps of the approval process. This includes threat assessments on new and existing structures. SME’s (Subject Matter Experts) must be present at all stages. The blasting industry and regulators must work collaboratively to improve safety, security, and create a dialogue with law enforcement and the AHJ. Relationships are built through trust, teamwork, transparency, and communication and greatly improve the safety of our great country.

Jan 21, 2025

By L C. Taylor

Both the U. S. Navy and the U. S. Army are interested in knowing more about the loading applied to vehicles which are unfortunate enough to encounter a detonation of a buried mine in the course of performing their normal duties. The Dynamic Effects Laboratory at the University of Maryland has been involved in small scale testing for ten years to assist the Navy and the Army in understanding the loads that are applied to personnel carriers when a buried explosive detonates beneath them. This paper describes results from small scale tests conducted to determine the loading mechanisms on target plates when subjected to loading due to the detonation of a buried mine in saturated sand, dry sand, and water. Transparent target plates were utilized in order to determine the loading process beneath a floor board on armored vehicles. Various charge sizes were scaled in the laboratory accordingly to a standardized full size threat encountered in the battlefield. Tests were conducted in saturated sand, dry sand, and water keeping the stand-off distance of the target and the depth of burial of the charge constant. In the case of water impacting a transparent PMMA plate the crack propagation was recorded and the crack velocity is determined. Additional tests were performed in saturated sand by varying the stand-off distance of the target but keeping the depth of burial of the charge constant. The small-scale test results could be scaled to full scale by using verified scaling laws.

Jan 1, 2016

By Kevin Phelps, Jason Baird, Philip Mulligan, Dominique Nolan

Determining the transitions from run-up to optimal cut length and optimal cut length to run down, without bias, from the penetration of a linear shaped charge (LSC) is difficult. The stresses applied to the targets during explosive testing can distort the targets in such a manner that determining the true distance of cut, penetration, or fracture can be demanding. Through the course of this research, it was observed that the researchers made many of the errors involved in the collection of data. Among these errors researchers found problems in: determining and fitting the sample to a single plane from which to read measurements, determining where along the path of cut the three phases of penetration transition, and the precision of measurement based on handheld tools and the human eye. This study looks at three methods of recording the data of a series of linear shaped charge tests. The tests resulted in samples which are not ideal for measuring with common laboratory devices like measuring tapes, calipers, or rulers. The first method utilized these common laboratory devices and the difficulties the authors experienced are described in this paper. The second and third methods involve digital photography, image manipulation, and the use of AutoCAD. Methods two and three are then compared to the simple observational method and discussion is made in regards to the precision and accuracy of each method.

Jan 1, 2013

By Sami Kara, Yunseok Park, Seung-Joong Lee, Namsun Hwang, Michael Laing

This study conducts a comparative analysis of construction efficiency. In the first part we compared electronic and non-electric initiation systems, focusing on tunnel contour holes. Field blasting operations were executed across a variety of delays to identify the optimal delay time. This delay for the in-situ rock mass was determined through regression analysis of blasting vibration in contour holes and for overbreak/underbreak. The blasting results with the electronic initiation system using the obtained optimal delay, applied to contour holes, were compared with the results of the non-electric initiation system. The overbreak and underbreak decreased by an average of 2.7 cm and 5.8 cm respectively, by using the electronic initiation system. Moreover, the vibration reduction rate in contour holes region was reduced by 11.9% based on the blasting vibration estimation equation proposed by the Ministry of Land, Infrastructure, and Transport (MOLIT). Underground construction projects have become increasing popular as cities grow in both size and density. This growth severely limits the amount of useable space for new project on the surface, resulting in the decision to build them underground. This new policy however brings into focus the challenge of managing and reducing blasting related vibration due to the proximity of these projects to sensitive structures, utilities and foundations often present in urban environments. For this purpose, we have been required to manage the vibration by reducing the quantity of explosives used per round. Inspired by surface blasting techniques, we applied a decking mode to address and work around this challenge. We present in this paper the first attempt to blast a tunnel face using a decking method and reduce the charging per hole from 6 kg to 3 kg per hole and keep the same advance rate for this tunnel. The results are presented in the third part of this paper. In the second part we present the results of the decking mode in shaft. The use of the electronic initiation system in tunnel construction provides the users an effective tool to improve the overbreak/underbreak and keep the vibration at a low level with a large gain on the overall project schedule and budget. This what we want to demonstrate in this paper.

Jan 21, 2025

By Guo Ziqing, Tang Qiuming, Liu Yuanyuan

The channel-type non-mechanical stirring production process is a new developed technology for emulsion explosives in recent years. It removes traditional equipment such as mechanical-mixing emulsification, mechanical-mixing sensitization, matrix pumping, and explosive pumping, and has been applied in China. This technique achieves a fusion of higher intrinsic safety and lower cost, as well as the excellent quality of products and high efficiency of production. The emulsion particle diameter is about 0.5μm. The storage period of emulsion explosive produced with span-80 emulsifier is more than 7 months.

Jan 21, 2025

By R. Hazael, R. Alford, R. Critchley

The ability to compare explosives is fundamental. Numerous methods are used and while simple conversion factors are often used, the use of TNT Equivalency (TNTe) is not a simple subject as explosives exhibit very different equivalencies depending on whether the pressure or impulse are being considered as well as other conditions. The scaled distance has been found to have a significant effect on the TNTe but due to the difficulty of taking measurements at very close ranges, no TNTe have been quoted for charges in direct contact (Z=0). This paper describes the use of a ballistic pendulum to measure the impulse from contact charges and presents some surprising results that require a two-stage propulsion, as originally described by Backofen, to be explained.

Jan 1, 2024

By Rob Farnfield, Mark Pegden

Old Cliffe Hill quarry produces between 4 and 5 million tonnes of crushed granite per year and is located in the county of Leicestershire in the East Midlands region of England. Blasting is carried out with bulk emulsion explosives in combination with either shock-tube or electronic detonators.

Jan 1, 2010

By D J. McLane, J T. Rathbun, B T. Lusk

The dynamics of explosive detonations are understood, however recreating a real-world, full scale scenario is costly. The use of a shock-tunnel allows testing to be done on a smaller scale, with the simulated effect of a large explosion. Analyzing explosive waveforms using this method can greatly reduce cost in testing blast resistant products, such as anti-terrorism devices, mine safety products, and military equipment. The purpose of this paper is to better the understanding of how the waveform characteristics resulting from an explosive detonated within a shock-tunnel differ from those in an open-air arena test. The variables of comparison between an open-air arena test and those conducted within a shock tunnel are peak pressure, impulse, shock wave velocity, and cross sectional shape of the shock front. Understanding how these variables differ, tests utilizing a shock tunnel can be conducted with a higher degree of accuracy and repeatability.

Jan 1, 2013

By Dale S. Preece, Ruilin Yang

Shock wave physics is an important part of air-deck behavior since the bulk explosives in the column impart a shock into the air-deck where the air shock then passes through the air-deck at a rapidly attenuating velocity. Through both high-fidelity modeling and shock physics theory it is shown that the resulting pressure in the air-deck is two orders of magnitude less than the detonation pressure of the explosive. The induced air blast reflects from the bottom of the borehole and this reflected pressure, even though doubled, is still approximately two orders of magnitude less than the detonation pressure. Air-shocks will ring back and forth in the air-deck for a few tens of milliseconds while the adjacent explosive column(s) are detonating. Transmission of the initial shock through the air along with reflections is an intensive energy consuming process. Energy balance results in shock heating of the air and a temperature increase. However, the increased temperature of the air is also orders of magnitude less than that of the explosive detonation products immediately behind the detonation front. Replacing high energy explosives with zero energy air-decks in a blasthole will always have a negative impact on the adjacent rock fragmentation and movement.

Jan 1, 2016

By Julijan Bratun, Joze Kortnik

Production of technical stone is an important economic branch in Slovenia. In 2009, we had 95 dolomite quarries, 27 limestone and 6 silicates quarries, according to the Ministry of Economic Affairs. Together they produced nearly 15 million tons of aggregates. The production in quarries is mostly performed with drilling and blasting method and only a minor part with other method like mechanical mining method.

Jan 1, 2011

By Jason Baird, Joshua Hoffman, Phillip Mulligan

The purpose of this report is to address the method of reducing the overall explosive weight of Explosively Formed Projectiles (EFPs) while still achieving satisfactory performance. This reduction is crucial in order to comply with outdoor explosives testing standards for Missouri University of Science and Technology’s (Missouri S&T’s) Experimental Mine. Initial EFP design testing exceeded given limitations, making reliable data difficult to ascertain. EFPs must be tested outdoors to allow for specific information recordings which aid in defending against them.

Jan 1, 2010

By Scott G. Giltner, Alex Schwenk

An iron operation sought to extend the life of the mine by conducting a major pit pushback in an area close to several public structures and the neighboring town. The result of the pushback would make millions of tonnes of ore available for mining allowing many additional years of taconite mining. This paper discusses the initial development blasts conducted for the pit pushback. For the development blasts, it was determined that no fly rock should leave the mine site and that the blast vibrations should be as low as possible, but specifically under 19 mm/s (0.75 in/s) at a nearby sewage treatment plant. One issue complicating the blast design was the variation in hole depth within any given blast. For the initial sinking shot, the hole depths varied from 6.4 m (21 ft) to 12.5 m (41 ft). In the subsequent blasts the hole depths within each blast could vary up to 5.8 m (19 ft). Various tools were employed to design the blasts to ensure there was no fly rock and that the blast vibrations were as low as possible. UAV surveys of the blast areas were conducted to provide a 3-D representation of the free faces and bench surface. The 3-D point cloud produced from this was used to measure the shape of the free faces. Once the shape of the free faces was quantified, it was possible to establish proper placement of the crest holes and develop a custom explosive load for each blast hole. In addition, signature hole analysis was performed for each blast to determine the optimum delay time that balanced the need for minimal vibration, prevent fly rock, and a well fragmented muck pile. Electronic detonators were applied to achieve the necessary control of the blast that balances these three concerns. The results of the seven blasts conducted to date provided the desired results. The peak vibration level at the sewage treatment plant for the seven blasts was 10 mm/s (0.40 in/s). The only fly rock occurred when there was a miscommunication in the blast design resulting in under burdened holes on the front row. To date, the mine has been able to safely expand the pit into an area that will add many years to the mine life. The muck piles have been well fragmented with reports from the shovel that they have all dug well.

Jan 21, 2025

By C. Heiss, A. Hofmann

Due to an explosion in an Austrian steel works during the basic oxygen process, the Chair of Mining Engineering and Mineral Economics at the Montanuniversitaet Leoben was assigned with the set-up of a test arrangement to study the effects of large-scale particle emissions on the plant´s installations and the testing of various structures and structure-combinations to be applied as explosive-proof enclosure.

Jan 1, 2012

By Ethan Steward, Kyle Perry

Blast resistant structural design continues to be a research area of major concern for governments around the world due to explosive threats from both state and non-state actors. Glass and aluminum curtain wall systems are commonly used to clad the exterior of government and commercial structures, allowing light into the building, regulating the interior environment, and providing an aesthetically pleasing exterior. These systems are likely to fail when exposed to sudden, high-pressure events such as the purposeful or accidental detonation of explosives. Engineers have designed blast resistant curtain walls and structural elements to reduce the likelihood and severity of failure, but the design tools and testing mechanisms commonly used in the process may not accurately model or simulate actual blast conditions at all ranges. In blast resistant structural design, the origin of a shock wave is typically assumed to be in the far-field, creating a wave that is nearly planar and parallel to at least one face of the target. Shock is applied evenly and immediately across the entire impacted surface. However, the source of real-life blasts is often very close to the target structure, and the assumption of far-field planar shock does not always apply. Mid-field blasts exhibit qualities different from those assumed about far-field shocks, specifically a hemispherical shock that produces different peak pressures, impulse curves, oblique reflections, and Mach stems across a target. This paper will examine mid-field shock effects from scaled distances of 2.5 to 4 13 (6.3 to 10.1 13) on a tall, scaled target by measuring reflected and incident pressure, impulse, and shock velocity across the target. Results will be compared to theoretical blast parameter equations and empirical data used by the industry. Possible effects of mid-field blasts on structures and further research ideas will be suggested.

Jan 21, 2025

By Ajoy Singh

A study was conducted to investigate the damage potential to underground multi-seam openings caused due to vibration generated by open-pit coal mine blasting. The objective was to recommend optimal explosives weight per delay to be detonated in open-pit blasts to ensure the safety and stability of underground openings. Sixteen blasts with varying charge weights and initiation sequences were conducted at Samleshawari open-pit mine and eighty four blast vibration data were recorded in the Hingir Rampur underground colliery in India. Analysis of vibration data showed that roof of the underground openings vibrated with higher amplitude of vibration compared to pillars and floors. The amplifications of vibration in the roof at the junction were upto 4.3 times the pillar vibration. It was observed that coal chips detached from roof when the peak particle velocity reached 131 mm/s or high. The vibration magnitude recorded was higher in upper seams openings than in below seam openings. Rapid attenuation of vibration was recorded in below-seam openings at similar locations. Appropriate particle-charge weight-distance equations were established to calculate the safe explosive weight per delay to be detonated in open-pit mine for safety of multi-seams workings of underground mine. The support for the galleries and junctions were further modified for the working seams to ensure greater safety.erground Coal Mine

Jan 1, 2012

By D. Scott Scovira, Thomas Gustavsson

The potential of hydrogen peroxide explosives was introduced to Thomas Gustavsson and Robert Håkland by Dr Miguel Araos through his development of hydrogen peroxide gel compositions (HPG). In 2020, Thomas and Robert developed a concept project with Boliden Minerals and received Swedish government funding to evaluate HPG technology in a mine environment. The project showed HPG reacted violently with mine mineralization and concluded that HPGs did not offer a commercial solution due to safety concerns. Thomas and Robert engaged with Stefan Nilsson to develop hydrogen peroxide emulsion (HPE) compositions and the process techniques to manufacture them. In 2021, laboratory work produced a promising low carbon intensity, nitrate free, ammonia free, emulsion formulation based on industrial grade hydrogen peroxide and a fuel-emulsifier phase. Design and construction of an HPE pilot plant and underground charging unit commenced. The manufacture of hydrogen peroxide emulsion shares several similarities with the production of nitrate-based emulsions in that the plant is a facility to blend a strong oxidizer solution with a liquid fuel phase into a finished emulsion. A key differentiator between HPE and nitrate-based emulsion is that the manufacture of HPE is a cold production technology in that neither the oxidizer phase (HP) nor the fuel-emulsifier phase requires high temperature heating to prepare raw materials. A successful proof-of-concept HPE evaluation ran from April 2022 to October 2022 at Boliden’s Kankberg underground mine in Sweden. This evaluation demonstrated HPE technology's safety, performance, production, handling, and indicative environmental benefits.

Jan 21, 2025