Search Documents

By A. Gontijo, A. Matos, P. Lincoln, L. Fonsecail

This paper investigates how to manage and model the vibrations caused by rock blasting in a Brazilian underground mine. Considering the frequent detonations and the previous lack of effective vibration control, understanding, and reducing the impact of these seismic waves is critical. We emphasize the use of the near field model technique, which considers the varied physical properties of different rocks, optimizes blasting plans, and minimizes damage to the rock mass. We detail a case study that demonstrates a comprehensive approach to vibration control. The discussion includes the creation of a monitoring plan, the methodology used, results and the specific challenges and solutions found during the blasting process. This study provides a practical guide for similar future projects. Finally, we present a predictive model based on the collected data, offering insights into the vibrations caused by blasting. This model helps decision-makers minimize the risk of displacing rock blocks in the blasting area, improving safety and operational efficiency

Jan 1, 2024

By R Wing, D Corkery

"Several mines in the region of Sudbury, Ontario, occur in or near populated areas. In anattempt to examine the effects of environmental changes and blast induced vibrations onhomes in the area, a monitoring study was conceived. The study was conducted fromNovember 1990 to May 1991 in homes located near the 880 Stope at INCO Ltd.'s CopperCliff South Mine."

Jan 1, 1993

By A B. Jr Nunn, W C. Gould

Good community relations is a major concern at this central Virginia aggregate quarry. In this paper, the authors describe the use of a new electric millisecond delay initiation system that has reduced the average level of vibration by 27% since its use began in late 1984.

Jan 1, 1986

By Edward J. Jr Walter, Edward J. Walter

The vibration problem is approximately fifty years old. The original investigation of the U.S. Bureau of Mines was begun in 1930. Significant investigation into the problem was done by Crandell, Langefors, et al, Edwards and Northwood, and again by the Bureau of Mines. This resulted in an effective Safe Limit standard expressed in particle velocity as 2.0 inches per second.

Jan 1, 1979

By Raymond H. Green, Mitchell W. Green

The authors examined the application of precise millisecond delay electric blasting at a well-known Vermont quarry. The paper explains how the use of a new high-accuracy electric delay detonator has improved fragmentation, raised productivity 10%, simplified blast design, and increased the ability to predict results from blasting.

Jan 1, 1986

By George Pittman, Dan McCutchen

When an explosive manufacturer in the USA wants to put a new explosive formula or detonator design in the toughest proving ground in North American, it is Florida. Florida conditions have baffled many creditable blasting experts. This paper deals with some of the methods used to overcome these problems.

Jan 1, 1995

By Francisco Leite, Tomi Kouvonen, Bianca Saraiva, Vinicius Miranda, Auã Oliveira

One of the main challenges facing mining engineers is to draw up a plan that can be implemented in a timely manner, taking into account the operational variability of the mine’s production processes. These plans are often drawn up based on deterministic modelling (provided there are a set of known inputs that will result in a single set of outputs), when in truth we are talking about stochastic events (the cycles involved behave like random variables and their nature may be studied and reproduced). The result of using this kind of methodology can lead to non-optimized intuitive choices, which may harm the long-term targets defined by the planning team. Based on this principle, this document investigates the simulation of the rock fragmentation process in an open pit mine to assess the stochastic behavior of the loading and haulage operating cycles. The data assessed by the simulation process were the total costs of these operations in function of the powder factor. Based on a sample set data items, it was possible to check the probability distribution of the event as a Poisson distribution, applied to the loading and haulage cycles. The simulation consists of the repeated sequenced reproduction of these events (Monte Carlo simulation), in order to find the configuration that best fits the loading and haulage operations. By integrating these systems, it was possible to better understand the influence of the blasting in these operations, and as such to reduce the associated costs.

Feb 6, 2023

By Javier Castaneda, Luis Zozaya, Noel Huarachi, María Rocha

The objective of the project was to implement and calibrate drill and blast models supported by Geotechnical and Geological models as well as the mine and operation characteristics. The models would then be migrated to HxGN Blast to ensure a productive process that is simplified, digitized and optimized.

Feb 1, 2020

By Paul N. Worsey

Disturbed zones of rock have been measured for blasted highway rock cuttings by Matheson and Swindells of the Transport and Road Research Laboratory (TRRL) of Great Britain. These zones have been shown to be directly attributable to the blasting process and accordingly vary in depth depending on blasting technique. Perimeter blasting such as smoothwalling and pre-splitting has been shown to be effective in reducing the depth of disturbed rock. Although extensive work has been carried out on surface excavations for medium diameter (l00mm) blast holes, none has been undertaken for underground excavations.

Jan 1, 1985

By John C. Brulia

PowerAN is a tradename of Atlas Powder Company for a new line of explosive products comprising blends of emulsion and ANFO in a variety of bulk and packaged grades. The bulk PowerAN grades are either augered or pumped depending upon emulsion content. Augered PowerAN blends contain up to 60% emulsion. Pumped PowerAN grades have an emulsion content of 75% or higher. The blending of PowerAN is usually accomplished at the borehole to satisfy specific borehole conditions. Packaged PowerAN grades are produced in several types of mix plants in diameters of 4" and greater. PowerAN 300 (30% emulsion) and PowerAN 500 (50% emulsion) are the two most popular grades and their chief application is as an economical, high energy replacement for ANFO HD in wet holes. PowerAN combines the cost effectiveness of ANFO with the high performance of emulsions, permitting the blasting engineer to strike an optimum balance between drill pattern expansion and increased productivity according to need.

Jan 1, 1985

By Dr. Zach Agioutantis, Elliott Morgan

The explosives, mining, and heavy civil industries consistently battle the uncertainty that is associated with working with a heterogenous medium like rock in blasting. This has led to studies to increase fundamental understanding of material response under dynamic loading that is associated with blasting. This study looks at the dynamic strain associated with blasting the lab Split-Hopkinson Pressure Bar (SHPB) testing while also building off of previous studies with the goal of better understanding the dynamic forces that are enacted on a geologic body during a blast loading event. This is required in order to advance geologic blast response modeling. This is achieved through analyzing the stress and strain values for each specimen that are calculated from strain data collected with a SHPB. Based on this data, the dynamic material response characteristics are able to be determined. Tests were conducted on five Berea Sandstone specimens with a rough length to diameter ratio (L/D) of 1.0. The strain data from these tests were then used to create stress strain curves as well as charts depicting failure stress to both strain rate and failure particle velocities. The tests conducted returned similar results to previous tests results on Berea Sandstone while also showing a correlation between strain rate at failure and failure particle velocities. While further research is needed, there is evidence that SHPB test data could be used in conjunction with the MBF model. The MBF model states that the peak particle velocity (PPV) of blast vibrations can be correlated with deformation (strain) at a given point. With a further understanding of dynamic material response correlated to PPV measurements, further refinement could allow for better prediction of blast performance.

Jan 21, 2025

By Stephan Iversan, Janae Singer

High resolution seismic refraction tomography has proved to be a useful tool to effectively estimate depth of blast induced damage in rock. Excavation blast damage can be as shallow as 1 to 2m (3 to 7ft) and requires resolution at a fraction of a meter for effective imaging. We used an accelerometer with flat frequency response to 1000Hz to record data at spacings of approximately 0.25 to 0.5m (0.8 to 1.6ft) along mine walls. The resulting tomograms of P-wave velocity show low velocity zones which we interpret as residual fracturing from blasting. Experiments on a concrete test block and at two underground mine locations give results that are consistent with fractured rock transitioning to competent rock.

Jan 1, 2009

By Tom McDonald, Rodney Burke

As mining progresses in the West, the depth of material has increased, making highwall stability a major factor in safety and production. The Jim Bridger Coal Mine has made highwall stability a priority, concentrating on safety as well as increasing and improving production. Overburden depths are increasing dramatically; the geological environment consists of medium to soft material, faulting, water, and current pit alignment not favorable to joint planes. Angle drilling the presplit at 20 degrees became necessary as vertical presplit drilling produced wall failures.

Jan 1, 1997

By Isaac E. "Chip" Harris

A general understanding is given to how and where blast hole drills are used and what recent developments have taken place with small and large diameter drill hole machines. Indications are that new developments with high penetration rates and large diameter holes are not necessarily the answer to increased production in the field.

Jan 1, 1979

By Michael S. Wieland

This report discusses measurement techniques utilized in and trend results obtained from research on delay blasting malfunctions in underground coal shots at the U.S. Bureau of Mines. Charge malfunctions occur during delay blasting in underground or surface mines, rendering the explosive operations more hazardous and less productive. Modern instrumentation techniques reveal several types of reduced charge performance, resulting from cross-hole interactions. Two receptor (wave-target) charge malfunctions were detected in fourteen shots that were undeniable. There were other receptor charges that exhibited under-performance by registering out-of-tolerance or noticeably reduced detonation rates. Delay blasting generates tremendous shock waves and rifting forces that fracture and heave the surrounding stratum and unfortunately damage remaining unfired charges. This report contains two graphs, representing roughly 1% of total records, that show donor (wave-source) charge shock waves and rift (reaction-to-heave) compressions. These debilitating wave impacts precipitate modes of reduced charge performance ranging from weak detonations or misfires to sympathetic detonations. As recognized from previous research, impaired charges react poorly, perform less useful work, and yield fumes with atypical higher toxicity.

Jan 1, 1995

By Richard G. Burdick

The use of explosive charges for generating seismic energy has been around for a long time. For oil-field work or crustal studies, when the target of interest is many thousands of feet deep, the surface waves and similar phenomena are of little consequence. In mining applications, however, when the target is a few tens or hundreds of feet deep, the return signals are often masked by these waves and an accurate interpretation is difficult or impossible.

Jan 1, 1981

By Tom Watts

This paper will focus on the design, manufacture and use of pump safety systems on MMUs (Mobile Manufacturing Units – Bulk Trucks) with progressive cavity pumps. The practice of pumping bulk blasting agents is highly regulated and the explosives manufactures have done an excellent job of hazard and operability studies allowing criteria to be established for the safe pumping.

Jan 1, 2009

By Douglas R. Simms

O & G Industries, Inc. owns and operates a number of rock quarries within the State of Connecticut. These rock quarries are surrounded by residences and commercial neighbors who have concerns related to blasting. In addition, local commissions which issue the mining permits to O & G are required to hold public hearings, prior to issuing the annual permits each year.

Jan 1, 1994

By John M. Bolger, Keith E. McMaster

Excessive salt fines are undesirable in underground salt mining as they are considered a costly waste byproduct. This paper describes an extensive explosive application program conducted at The Canadian Salt Company Ltd, located in Pugwash, Nova Scotia, Canada. The prime objective of the program was to reduce the quantity of fines generated from this company’s underground production blasts. The program was known as the “The Fines Reduction Program”.

Jan 1, 1996

By Ronald Ticona

Generally, the drilling and blasting operation are managed independently to the processing plant outcomes. Therefore, the technical segmentation to determinate the ore drill and blast designs do not include processing plant rock properties such as Bond Work Index, Axb, Drop Weight Index or other. This work describes the case study of a copper mine in Peru, which, together with its strategic partner ORICA, have implemented projects focused on optimizing mine fragmentation. The year 2021, mine operation according to its mine plan would have a significantly increased SAG mill hardness, which would impact directly on copper concentrated production. An integrated strategy from mine to plant has become necessary to maintain the production levels.

Feb 6, 2023