Search Documents

By J J. F Smith

The application of pneumatically loaded ANFO for underground mining has continued to increase year by year since the technique was first developed and introduced underground during the early 1960's. Improvements in the manufacturing process for explosives grade prills, the design and construction of more efficient AN prill-fuel oil blending equipment, and the introduction of more durable and reliable pneumatic loaders have promoted the wide application of the relatively low cost blasting agent, ANFO.

Jan 1, 1982

By Erik C. Nygaard

ANFO is the most used industrial blasting agent in the world, and is often used as a reference for comparison of other explosives. It is known to work very well under dry conditions in large borehole diameters, whilst in small bore hole diameters the formation of high amounts of toxic fumes (CO, NO and NOz) can result. In underground blasting, problems can also occur with reduced visibility caused by uncombusted ammonium nitrate.

Jan 1, 1999

By A N: Zditovetsky Shishov, M G. Menzhulin

At present in a building industry demand for products from granite, gabbro and other rocks, steady to erosion, natural and chemical weathering, was essentially increased. It has caused the enlargement of exploitation of stone block deposits and necessity of creation of new technologies of hard stone cut.

Jan 1, 1996

By Neal Lee

Reduced relief horizontally means an increase in energy expended vertically into the rock surrounding the stemming column, and potentially through the stemming column. The vast majority of holes in any surface blasting operation are afforded two horizontal relief faces at the moment of firing, whether by existing relief faces in front of and to one side, or previously blasted hole(s) in front of and to one side of the holes in question. When the energy expended in any hole on the blast pattern has less than two Horizontal Relief Planes or faces (referred to moving forward here as “HRPs”) available to it at the moment of firing, a higher percentage of the available energy is directed vertically. In the analysis of recorded videos by the author, one will note the fact that stemming ejection/flyrock is observed to a much greater degree from the center of almost all patterns when they are timed to “pull out of the middle” (“box cut" timed patterns). This is because the first hole to fire in each row has only one Horizontal Relief Plane, which significantly decreases horizontal avenue for energy release for these holes. This of course results in an increase in the amount of energy expended vertically. This paper proposes a novel methodology to modify the stemming to better use the explosives energy of each hole, while controlling side effects such as flyrock and airblast.

Feb 6, 2023

By Michael Wieland

Delay blasting in underground coal generates shock waves and rifting forces that damage charges remaining in the blast pattern. Damaged charges detonate poorly, raise fume toxicity and reduce coal breakage. Such circumstances could be prevented by using explosives resistant to cross-hole interaction damage. The design of rugged explosives is fraught with contradictory requirements, but tradeoffs related to hard-particle size characteristics prove useful. Hard particles, related voids or trapped bubbles represent reaction nucleation centers which strongly influence the performance of coal mine explosives.

Jan 1, 1992

By Pat McLaughlin, J R. (Dick) Daniels

Current practice in establishing quarries in remote areas with hilly or mountainous terrain tends to the use of airtracs (or similar pioneering units) drilling horizontal holes to establish a face, followed by bench development with light excavating equipment. The authors propose the use of a hybrid coyote blast design that incorporates long-round tunneling techniques. This method would, in effect, use down-the-hole (DTH) drills to advance the drift cut to the final depth, allowing longer and more rapid drift advances, and replace the cross-cut drifts with clusters of DTH holes to achieve the same explosives distribution.

Jan 1, 1995

By Dale Nies, David P. Childs

The open pit gold and silver mining operations in the State of Nevada have historically used simple row by row, echelon, or chevron delay patterns. Common practice has been to use detonating cord trunklines and either detonating cord downlines or nonelectric common in-hole delays in conjunction with surface delays. Several operations use a series of downhole nonelectric delays with an entire row loaded with the same delay to develop similar patterns.

Jan 1, 1991

By D J. P Jordan, C V. B Cuningham, A J. Rorke, C G. Ladds, O L. Davey

"During the early stages of the boxcut mining at the Arthur Taylor Colliery, Open Cast Mine(ATCOM), problems were experienced with blasting results. Very large boulders andportions of completely unfragmented rock were commonly encountered. A full blastmonitoring programme was instigated by the mine and the explosive supplier to solve theproblems and to optimise future blasting operations at the mine."

Jan 1, 1993

By A. Pope

I have attended two Explosives Engineers’ Conferences in the past 4 years. The first was in Brighton, England with the European Federation of Explosives Engineers in 2005 and the International Society of Explosives Engineers in New Orleans, USA in 2008. At both of these conferences I listened to papers presented on European and English training methodologies and ideologies. As I have been training Shotfirers for the past 18 years in Queensland and the Northern Territory for some 8 years previously, I would like to present our methods of training in Queensland, which I believe is among the best in the world. In Queensland, this training is carried out by a training organisation that is registered by the Department of Education, Training and the Arts under the guidelines of the Australian Quality Training Framework (AQTF). Not only is this Registered Training Organisation (RTO) required to operate under these very comprehensive guidelines, but also those designated by the Explosives Inspectorate of the Queensland Department of Mines and Energy.

Jan 1, 2009

By Ryan Redyke, Jared Redyke

The demolition of an old power plant boiler house in Parsons, Kansas calls for the use of some linear shaped charges. The steel is thick and the structure is heavy but gravity can be a blaster’s best friend. This entry did not win in a very competitive category. We thought it was worthy of coverage in the Journal of Explosives Engineering.

Jan 1, 2015

By Unknown

Contact Local Law Enforcement Authorities. Contacting the local law enforcement authorities is essential to the quick recovery of explosives taken in a crime. Contact Local ATF Office. The local ATF office will work with the local law enforcement authorities investigating the theft. They can also assist in the preparation of the Theft/Loss Report for submission to the U.S. Bomb Data Center.

Jan 1, 2009

By Paul Worsey, Barbara Robertson

In June 2007, Missouri Science & Technology (formally UMR) successfully held its 5th and 6th Explosives Summer Camps. The camps, which include substantial industry participation, have been an outstanding success with both the students and their parents. They have also spawned a large amount of local, state and national media attention, including NPR and an article in the New York Times on the 3rd of July 2007.

Jan 1, 2008

By Dave Howerton, Marshall Williams, Dave Finnerty

This paper will be presented jointly by El Dorado Chemical Co. and Arch of Illinois. It will deal with the simultaneous blasting of multiple overburden seams in surface coal mining. With the development of a new pit in Southern Illinois, production personnel with Arch were faced with serious equipment cycling problems. The solution to the problem was the development of a procedure that reduced drill movements on the highwall.

Jan 1, 1992

By John Brulia, Grant ODell

The AIRDEK blasting method has recently been introduced as an overbreak control blasting technique. This paper discusses the use of a modified AIRDEK blasting method for use in open-face blasting to make cap stone riprap (6-20 ton size) at the Clinton Point quarry of New York Trap Rock Corporation, Lone Star Industries.

Jan 1, 1990

By David Siskind, Mark Stagg

Vibrations from Dade County (Miami area) quarry blasting and structure responses were measured at 11 locations between February and April, 2000, and 10 homes were inspected to analyze the characteristics of their cracking and other damages. These results were combined with information collected by the County and other studies done in south Florida for a blasting impact assessment specific to this area. In addition over 40 quarry blasts in the nine-week monitoring period, about 800 measurements were available from previous monitoring in Dade and neighboring Broward counties. An overall worst-case analyses based on the highest individual amplitudes suggested that vibrations in some areas could have been as high as 0.35 in/s. While amplitudes in the study period were below this value, they were found to be relatively high for the distances and charge sizes. Attenuation with distance is less in Dade County than found elsewhere with quarries having to use scaled distances several times higher than similar sites in the north. Consequently, the vibrations are perceptible at very large distances.

Jan 1, 2001

By Lewis L. Oriard

Near the village of Villarino de los Aires, in the province of Salamanca, Spain, was an existing underground hydroelectric power plant. A major enlargement was undertaken to increase the electrical generating capacity, under a contract awarded to a joint venture of Dragados y Construcciones, S. A. (Spain), Entrecanales y Tavora, S. A. (Spain), and S. A. Conrad Zschokke (Switzerland). The enlargement required the excavation of a large and complex underground system of tunnels, shafts and chambers adjacent to existing facilities and interconnected with these facilities. The existing machine hall and transformer chamber were both extended, requiring the blasting of the existing end walls. The drilling, blasting and excavating of the underground system had to be done without damage to existing underground chambers and tunnels, or any of the existing structures, equipment or instrumentation facilities, often within just a few feet of the blasting. This required careful control of vibrations, airblast overpressures and dust.

Jan 1, 1997

By Jack Eloranta

Transmission of sound through the atmosphere is affected by local conditions. Anecdotal accounts of the sound of cannon fire traveling great distances go back to the Civil War. The Royal Society published a paper near the turn of the century concerning the reports from the cannons fired in London at the funeral of Queen Victoria. Early computers were used by the U.S. Army at Aberdeen in Maryland in the 1950’s to model airblast problems during munitions demolition. Today’s blaster has to have access to weather information beyond a simple local forecast. Surface winds, winds aloft and temperature profiles have a dominant role in neighbors reaction to blasting. Many ground vibration complaints are really airblast complaints. Blasters who maintain ground velocities under . 1 inches/ second are often perplexed by complaints from distant neighbors, even when local monitoring shows airblast to be under 110 dB. This paper will help the blaster identify warning signs of high airblast conditions.

Jan 1, 2000

By Michael Louis, Charles Dowding

Concern over construction vibration-induced cracking has led to development of a new approach to vibration monitoring called autonomous crack measurement (ACM) and illustrated in Figure 1. This paper describes the concept as well as sensor performance in the first test house fitted an ACM system. Response of three cracks in this concrete masonry unit (CMU) house was measured as part of the system verification. ACM employs a single sensor that measures both weather-induced micrometer changes in crack width and those produced by habitation and ground motioninduced vibration. This comparison is displayed in real time via the Internet without human interaction. Graphic display through the Internet provides a new pathway for communication with the public. Such visual comparison of changes in crack width provides a simple alternative to the present system of comparison of measured and allowable vibration time histories. Measurements reported herein show that weatherinduced response of cracks is greater than that caused by presently allowable construction-induced vibration.

Jan 1, 2003

By Ray Jambakhsh, Craig Copping

The St. Lawrence Seaway's Welland Canal has been undergoing a rehabilitation program that requires the removal of deteriorated concrete from the 25 meter high lock walls. Multi million dollar contracts must be completed during the three month winter freeze up. New blast designs have drastically cut the time required for concrete demolition. All blast results including vibration, noise, underbreak, overbreak, scaling and flyrock have been improved and at a lower cost.

Jan 1, 1994

By Tom Hale

Developers and blasters are faced with increasing public demand and regulatory restrictions to maintain the lowest possible levels of noise and vibration from blasting operations in populated urban areas. Pyrotechnic products have proven to be a low noise, low vibration alternative to conventional blasting for close-in rock excavation and concrete demolition applications. Pyrotechnic breaking charges often yield 1/10th the vibration and noise compared to traditional explosives, and have been demonstrated to increase public confidence and decreased damage potential where they have replaced explosives, thus allowing new opportunities for work and greater job profitability. This paper presents a practical approach to utilizing pyrotechnic products in various applications including trenching, mass excavation, demolition, and dimension stone production, providing methodology for pattern design, vibration probability and loading calculations. Field research data is reviewed and compared to conventional explosives.

Jan 1, 2008