Search Documents

By Carlandrea Albonico, Salvatore Miranda

After a brief introduction of the whole Project, the paper describes two special geotechnical engineering solutions provided within the scope of the Galataport Project, in Istanbul, Turkey. The first refers to the new quay of Salıpazarı, which is a combination of retaining structure and ground improvement, formed by a combiwall, a reinforced concrete diaphragm wall and a soil improvement by deep soil mixing (Turbojet). The second, refers to the soil improvement works executed underneath three existing buildings. Single-fluid jet grouting columns had the scope of improving the mechanical properties of the bearing soil and reducing the associated risk of liquefaction. A set of underpinning micropiles was installed in order to allow the excavation of a partial basement inside two of these three buildings. All activities were conducted from inside the existing buildings, with reduced headroom. The paper highlights the importance of employing cutting-edge technologies within the foundation engineering field and state-of-the-art electronic control devices, in parallel with the essential human expertise, in order to obtain the desired results in this high-profile Project.

Nov 1, 2022

By Arturo Ressi di Cervia

Construction of the drilled shafts for the Brightman Street Bridge Replacement Project were not only challenging due to working over the water but were also challenged by changed soil conditions, concurrent work being performed by an adjacent contractor on the same project, environmental restrictions and severe winter conditions. A total of 36 x 8 feet diameter drilled shafts with 7.5 feet rock sockets were installed for the East and West bascule piers. This project also included Osterberg Cell load testing on two production drilled shafts at each the East and West bascule piers. The results from the load test program were used to fine tune the design of the drilled shaft rock sockets. From a constructability standpoint the reverse circulation drilling method with a pile top drill rig proved to be an excellent choice for drilling the overburden and rock sockets of the large diameter deep drilled shafts.

Jan 1, 2003

By Geoffrey Birch

A skilled and efficient workforce is a pre-requisite for the success of modern construction companies. The drive for improved performance, innovation and best value must be matched by the enhanced skills of the construction personnel. Training has been accepted as one of the essential cost effective elements to achieve these goals. The foundation industry demands particular specialist skills and requires focused training for its dedicated operatives. The introduction and development of specific training qualifications for the foundation sector is providing significant benefits.

Jan 1, 2000

By W. D. Guo

With an experimental apparatus developed recently, model tests on piles were conducted in sand subjected to triangular soil movement profiles. Four instrumented piles tests are reported, which show the pile behavior predominantly determined by soil sliding depth. Axial load can create additional bending moment and pile deflection, which also make mode of pile-soil interaction change with sliding depth. Limiting resistance was found 1.5~3 times higher than currently used for laterally loaded piles in sand.

Jan 1, 2006

By Helen S. W. Chow

The use of piled raft foundations for tall buildings has been increasing in this decade as it is an economical alternative to conventional piled foundations. Piled rafts are composite structures comprised of the piles, raft and soil and so soil-structure interaction is important in computing the behaviour of the foundation. In this paper, the behaviour of piled rafts subjected to non-uniform loadings will be examined where the raft is supported by piles of different lengths. Finite layer techniques are used for the analysis of the horizontally layered soils and finite element techniques are used for the analysis of the raft and piles. This method accounts for the soil-structure interaction and the lateral resistance of the soil on the piles and raft. Results provided from the present method are compared with the results of a full 3D finite element analysis.

Jan 1, 2006

By Kazuyuki Matsuzawa

A series of plate loading tests were carried out on a loam ground in order to investigate the influences of the plate size and the loading rate on the observed load-settlement relations. Two circular plates having diameters of 0.3 m and 1.0 m were used. Three types of loading methods were employed; 1) static cyclic maintained load test, 2) static continuous load test, and 3) rapid (dynamic) plate load test. An interpretation method called non-linear damping method was used to estimate a static load-settlement relation from the rapid plate load test signals. The derived static load-settlement relations match well with the measured results from the static load tests.

Jan 1, 2006

By Mario Aiezza

This paper outlines the results of a relationship developed during the design and construction of the foundations for the Gallery Towers project in Melbourne. Both the builder and the piling contractor were determined to arrive at a satisfactory foundation solution to the problems encountered at the site. The scope of piling work was to provide load-bearing piles under the building columns, some of which were located within a retention system that also required a piling solution. Geological conditions were variable and challenging. The site area was small and located adjacent to the National Arts Centre in the developed Southbank area, a high density office area. This presented logistical problems in limiting construction traffic on site and also demanding minimal noise and vibration emanating from piling activities. The piling contractor, Vibro-Pile, and the builder, Walter Construction Group, faced the challenges presented with a refreshing cooperative attitude that was beneficial to both companies. Commercial issues rising from design and construction problems were first put apart in order to allow the respective technical department of each company to work with minimum constraints to achieve the most cost effective solution. In the process usual adversarial attitudes resulting in loss of time and money was avoided. A number of issues were addressed successfully at minimum cost and time during this contract. Despite the difficulties encountered, the job was completed on time and with negligible claims for extras, resulting in the development of a strong mutual respect between both companies.

Jan 1, 2002

By Thomas C. Anderson

Thirty-four retaining walls are part of the $46 million upgrade of a 1942 depressed highway in Highland Park, Michigan near Detroit. This project will close a missing link between two newer roadways, I-75 and the John Lodge Freeway. The existing 75 ft. wide, six lane Davison Freeway is being replaced by a eight to ten lane, 200 ft. wide depressed highway in a limited right of way. The highway will be 20-25 ft. deep and 1.5 miles long. A design/build decision by the Michigan DOT saved about 37% of the engineers estimated cost of $19 million for the walls. The successful pre-qualified specialty contractor utilized an innovative solution for the walls consisting of tiedback/cantilevered walls on the north side and mechanically stabilized earth walls on the south side. All of the walls have an identical cast-in-place architectural facing.

Jan 1, 1999

By Li Tiemin

It is one of important tasks in research of vibratory pile driving to increase speed of pile driving and depth of pile driving -- this means to increase capability of penetrating hard layer. In general, vibratory pile driving hammer make pile be situated in vibratory situation to drive pile by means of weight of hammer and pile, but the depth of pile driving and capability of penetrating layer are limited by dead weight of hammer. This paper introduces a new kind of vibratory pile driving hammer which differs from general ham­mer. A set of pressing system is attached to hammer and pile driving frame. The pull of winch installed on frame passing guide pulleys bring downwards press to pile through absorbing system of hammer. The practice and comparison test have showed that the new hammer is faster in pile driving and bigger in capability of penetrating layer than general one. Now, the vibratory pile driving hammer with pressing device has been applied widely in China. RESUME: The vibratory pile driving hammer based on vibratory principle to design have applied wide­ly in foundation engineering in many countries over the world. In order to suit the needs of deep foundation, at present, how can quicken speed of pile driving and increase depth of pile driving have become even more value to many countries in the world. This paper introduces a kind of rapid vibratory pile driving hammer which can drive pile deeper and more faster comparing with common vibratory pile driving hammer. Therefore, a kind of simple and reliable method has been offered for rapid vibratory pile driving in deep foundation.

Jan 1, 1991

By Harry K. Weatherbee

The paper presents a design case study for a four-story correction facility addition in south Boston, Massachusetts, supported on friction piles driven into the Boston Blue Clay. 356 mm (14-in.) square prestressed-precast (PSPC) concrete piles were selected as they were found more effective and economical. A static load test was performed where the pile was brought to "failure". The load test data were evaluated to estimate the Ultimate Pile Capacity as well as the Ultimate Unit Skin Friction (Adhesion) to serve as a design tool for friction pile projects in the south Boston Area.

Jan 1, 2003

By Michel Bustamante

The occasional substandard performances of continuous flight auger in particular soil conditions have prompted the drilling rig manufacturer to improve the standard CFA in order to reduce its negative effects. A real improvement of interest was the launching of the double rotary CFA system. The promising features of the latter have incited the authors to implement an extensive experimental research on pile constructed using this type of technique but in the specific context of cohesive soils. Short-term static load tests were carried out on a total of 9 test piles of various installation techniques in order to compare the respective performances. The promising features of the double rotary CFA have incited the LCPC & Durmeyer Company to implement an extensive experimental research on this type of pile technique but in the specific context of cohesive soils and more particularly in clayey marls. After load tests completion the research has been completed by an excavation of the double rotary CFA piles. All the collected data concerning the implemented program are reported.

Jan 1, 2002

By J. A. Hayes

For over a decade the Osterberg Load Cell has been successfully used to determine the shear capacities of drilled shafts. Since the test method measures side shear directly, analytical complications due to the influence of end bearing resistance are removed. The data suggest that the side shear component of a drilled shaft's capacity is often more significant than end bearing. Given the interest in the use of side shear in drilled shaft design in compressible materials, it is important to examine factors that can influence capacity. We have found that some factors widely believed to influence capacity, such as slurry type, are not as important as commonly thought in most materials. Factors that are not usually considered as important, such as casing use, hoop spacing, concrete slump, concrete additives, spacers and rebar clear cover, seem to be more influential with respect to side shear capacity. For example, substantially lower than predicted shear resistance can occur when the rebar clear cover is small with respect to the cage diameter. We observe this most often in fine-grained cohesive soils. This effect can be exaggerated if the rebar cage has tight hoop spacing, if the concrete has low slump and if the hole is not straight. We have also noted that improper use of temporary casing can have a dramatic effect on side shear resistance. In some cases we have observed tested shear capacities reduced to less than 5% of either predicted or available shear values.

Jan 1, 2003

By Lianyang Zhang

For optimal design of rock socketed shafts used to support axial loading, it is important to predict the end bearing capacity. The existing empirical methods for determining the end bearing capacity of rock socketed shafts use the empirical relations between the end bearing capacity, qmax, and the unconfined compressive strength of intact rock, sc. Since rock socketed shafts are supported by the rock mass (both intact rock blocks and discontinuities separating them) not just the intact rock, one should consider not only the intact rock properties but also the influence of discontinuities when determining the end bearing capacity. Although the effect of discontinuities may have been implicitly (partially) included in the empirical relations derived from the results of load tests, it is not clear how big the effect is and how much of it has been included. In this paper, a database consisting of 50 test shafts, 25 of which contain the RQD (rock quality designation) value, is developed. Using the database, the applicability of the existing empirical relations is evaluated and two new empirical relations between the end bearing capacity, qmax, and the unconfined compressive strength of rock mass, scm, are derived. The new empirical relations explicitly consider the effect of discontinuities by using scm which is directly related to RQD. Finally, an example is presented to demonstrate the application of the newly derived relations.

Jan 1, 2008

By Giovanni A. Bonita

The new Embassy of the Peoples Republic of China in the United States (Chinese Embassy) is located in the Embassy Row portion of Northwest Washington DC. The 475,000 ft2 (44,125 m2) structure has five levels below ground and four above, making it the largest embassy in Washington DC. The structure approaches the property line on all sides, and is immediately adjacent to several foreign embassies and a secure U.S. Federal Building. A vertical soil nail wall was used as the primary support of excavation (SOE) system for the project. The soil nail wall was irregularly shaped, benched in areas, and reached total heights up to 98 feet (29.9 m). The soil nail and shotcrete system consisted of approximately 1,600 soil nails and 50,000 square feet (4,645 m2) of exposed shotcrete wall surface. Tight excavation requirements were defined for the project due to the location of the building relative to the property line, requiring fairly precise wall positions and shotcrete tolerances. Design challenges included soft soil conditions, inside wall corners, underground utilities, and seismic impacts from blasting. The paper will focus on the design, construction, and performance of the soil nail SOE system, as well as touch on the logistical and political factors that influenced the design. The paper also notes the Value Engineering and communication approaches that were generated during construction. These efforts resulted in a significant improvement in the quality control and quality assurance exhibited on site, expedited the schedule, and led to significant cost savings to the contractors, engineer, and owner.

Jan 1, 2006

By Gandhi

Piled raft foundation under uniformly distributed vertical loads has been analyzed using Finite Element Method. The soil is considered to be linear elastic, isotropic, homogeneous. The raft,pile and the soil have been idealized with eight noded brick elements. Parametric study have been carried out varying pile length, soil modulus, raft thickness, and pile spacing. Design charts have been produced to achieve 50% load sharing between pile and raft for optimum design. Data available in literature is compared with the design chart results and found satisfactory.

Jan 1, 1996

By V. M. Troughton

Large diameter bored piles with grouted bases have been adopted for the foundations of the majority of the buildings at Canary Wharf in London's Docklands, including a deep basement car park. The piles are founded in the Thanet Sand which forms part of London's aquifer where water levels are reported to be slowly rising. A special pile test has been carried out to determine the effects of both the basement excavation and a possible long term rise in the groundwater level on the performance of base grouted piles. These effects were simulated by injecting water around the pile toe and thus reducing the vertical effective stress. In this paper the test layout and procedures are described and the results are presented. The test results showed that the reduction in pile base resistance under increased water pressures was less than predicted by conventional design methods based on vertical effective stress. The end bearing resistance was found to be proportional to the mean effective stress.

Jan 1, 1989

By Seung-hoon Lee

The use of piled raft foundations has been considered as an economical alternative to conventional piled foundations because a portion of the applied load is carried by the raft in the design of piled raft foundation. In analyzing the behavior of a piled raft foundation as a settlement reducer, an accurate estimate of settlements of the system should be made on the basis of the understanding of nonlinear behavior of piles in layered soils as well as the interaction between the raft, soils, and piles. Although the 3-dimensional finite element method and simplified analysis methods have been used for the design of piled raft foundations, these methods were found to be inadequate for the practical purpose or could not consider the interactions properly. This study developed an approximate hybrid method of analysis to be used for the practical design of piled raft foundations considering pile-soil, raft-soil, pile-soil-pile and raft-soil-pile interactions. In the presented method of analysis, the settlements of the system are estimated satisfying the compatibility of two separate models which are the flexible raft model consisting of 2-dimensional finite elements supported by springs representing soils and piles, and the group-pile model embedded in layers of soil having different properties. Comparisons with other analytical methods as well as a 3-dimensional FEM program were made to verify the sufficient capabilities of the proposed hybrid model for application to practical design and analysis of piled raft foundations.

Jan 1, 2008

By Klaus Pöllath

The Netherlands RandstadRail project makes use of a large range of sophisticated geotechnical techniques to allow a shield driven tunnel to approach the central station of Rotterdam. This paper describes the construction of three deep excavation pits constructed with 1.2 m and 1.5 m thick diaphragm walls. Besides the presentation of the actual diaphragm wall activities special consideration is given to the break-in and break-out situations of the TBM into the deep excavations pits using sealing blocks and partly glass fibre reinforcement in the diaphragm walls.

Jan 1, 2006

By Y. El-Mossallamy

The piled raft foundation was extensive applied in the last two decades in different soil conditions e.g. in soft to stiff clay as well as in medium to dense sand and even in highly weathered rock. The piled raft is now applied not only to control the foundation settlement but also to minimize the required raft thickness to reach the most economic foundation design. An innovative application of the piled raft is its special adjustment to cases of foundations with large load eccentricities or very different loaded parts of buildings to avoid the need of settlement joints, which are especially complex below ground water table. Recently, the piled raft is applied for foundations of highway and railway bridges with special serviceability requirements regarding the allowable total and differential settlement as well as tilting. Actually numerical analyses are the mostly used design methods for piled rafts. For all day design practice a simple and modest design method is highly needed -at least in the first design stage- to check the feasibility of the piled raft on the specific project conditions. In this paper, a general overview on the recent innovative applications of piled rafts in Germany will be presented in a short overview. The results of the simple design method will be discussed and compared with the results of more enhanced numerical methods.

Jan 1, 2006

By Steven D. Dapp

The use of base grouting (tip grouting) to enhance the axial capacity of drilled shaft foundations can achieve improvements in economy and reliability for many types of projects and soil profiles. Recent experiences on a range of different construction projects in the Southeastern U.S. illustrate the most attractive opportunities for utilizing this technique and some limitations of the method. The quality assurance provided by measurements obtained during post grouting the pile toe is another important aspect favoring its use; the base grouting is shown to identify weaker piles and provide a means of remediating some deficiencies so that increased foundation reliability is achieved. This paper provides an overview of the methods used to evaluate and design for base grouted shafts along with lessons learned from several case histories.

Jan 1, 2006