Search Documents

By Nikolas Schmitz

For today’s construction industry, large-diameter piles are common practice, as they are more competitive than drilling a larger number of smaller piles. More and more piles are installed by drilling rigs, replacing the installation by hammer, vibrators or caisson. Equipment capabilities and technics with rotary drill rigs are highly developed, but very costly and time-consuming when it comes to rock drilling, large diameters and deep foundations. Pile top drill rigs (PBA), based on reverse circulation drilling (RCD) technology, overcome these challenges and are an efficient solution for large diameter drilling (0.6 m to 8.0 m/19.7 ft to 26.3 ft) and drilling depths of up to 500 m (1,640 ft.)in various geological conditions onshore and offshore. The paper will explain benefits of RCD technology and prove this with figures from the Mumbai Trans Harbour Link project.

Nov 1, 2022

By G. Price

The Building Research Establishment installed a base load cell in a driven cast-in-place pile prior to it being tested under vertical load. The monitored base loads were found to be significantly less than could have been predicted by current design methods. The less than expected capacity was attributed to the drilling out procedure. An electro-level system installed in a second similarly formed pile, provided detailed information on the performance of the pile under lateral load. The information obtained was used to check several current design methods for laterally loaded piles. The findings show the potential dangers of attempting to improve design parameters from only limited performance data.

Jan 1, 2010

By Raffaella Granata

The paper deals with the remediation of two areas formerly utilized for the disposal of hazardous wastes in a petrochemical plant. The works, designed on the basis of the criteria of maximum safety and minimum environmental impact, consisted in the confinement of the contaminated soil and groundwater within surface caps and perimetrical cut-off walls embedded in the underlying clay layer. The cut-off wall is 0.8 m thick and has a maximum depth of 33 m: it was designed to guarantee, as a minimum, the level of safety for a landfill for hazardous wastes, in accordance with the applicable National Standards. It was constructed with self-hardening mud and with the installation of an HDPE geomembrane. The HDPE liner of the cut-off wall was then sealed to that of the capping to obtain the complete encapsulation of the contaminated soil. A system of piezometers allows the monitoring of the cut-off efficiency measuring the fluctuations of the groundwater table and testing the chemical contents. Some wells installed within the contaminated areas will contribute to guarantee the full efficiency of the system in case of state of emergency, controlling the water-table level inside the confined areas.

Jan 1, 2006

By A. R. Katti

The stone columns are widely used in the improving the bearing capacity of weak soils mostly for supporting flexible foundation systems. The load carrying capacity of a stone column is complex in nature. The load capacity is derived from the lateral stresses acting on the stone column due to load transmitted from the flexible structure due to deformation to soil mass and which in turn transmits lateral pressure in s3 direction. The load capacity is also function of the f value of the stone column, cohesion of the surrounding soil, K0 and Gb2 of surround­ing soil including passive resistance developed to lateral deformation of the stone column. The assessment of axial and radial deformation is much more complex. Recently Katti et.al. have developed a method based on a granular heap approach and computed with equivalent fe. which combines the effect of s3a and equivalent volume concept to estimate radial and axial strains. In this paper an attempt is made to put forward guidelines for design of stone column accounting for both stability with respect to shear and also with respect to settlement. The estimate of settlement are based on the internal properties of stone column and surrounding soil. It is considered thus the settlements computed are more realistic.

Jan 1, 1996

By B. N. Hira

A multistoreyed residential complex was at the penultimate stage of construction by ONGC at Nazira, Assam. The site was situated at high earthquake zone. The subsoil was very weak and contained soft to medium clay with water table almost at the ground level. The bearing capacity of soil was quite poor particularly with predicted settlement beyond permissible limit. In this situation, the conventional shallow and deep foundations were found uneconomical and ground improvement with granular piles was considered as the viable solution. ONGC approached the Central Building Research Institute with the request to design granular piles along with R.C.C. foundation and other suitable cost effective measures. CBRI collected relevant geotechnical informations and supplimented the data by conducting field tests at site and laboratory tests at Roorkee. Rational design of 30 cm dia. and 5.00 meter deep granular piles were suggested with isolated and combined RCC footings over the reinforced soil. In addition to several structural and geotechnical advantages, the granular pile foundation provided considerable economy in the cost of construction. The paper presents the salient geotechnical and structural informations of the challenging project and provides the design details of the innovative granular pile-system. It also furnishes the design approach of the RC footings and other elements of the foundation.

Jan 1, 1996

The process of pile driving disturbs the soil around the pile. The nature and magnitude of disturbance depends upon 1) the pile size, and 2) the nature of soil. Therefore, the prediction of a single pile behavior based on soil properties of undisturbed soil samples may not match its performance. Under lateral loads, the pile may loose contact with the soil near the ground surface especially in clays. The soil pile interactions are influenced the most by pile behavior in this zone. This situation further affects the tally of prediction and performance. Piles are used in groups. The zones of overlapping stress from one pile to the other both around the pile and below their tip particularly in soft soils, contribute to group effects. Empirical solutions have been developed for prediction of the pile group behavior. The group action is more involved under vibrations. Several cases of single piles and pile groups under static and dynamic loads from published records have been analysed. It has been shown that single pile test is the best source of information on the soil-pile-soil interaction effects.

Jan 1, 1989

By Jay A. Berger

Nondestructive testing of deep foundations for integrity problems made great strides in the late 1980's. Inexpensive portable computers have allowed the immediate and rapid processing of field measured acceleration records which can provide insight into the relative structural integrity of a previously installed foundation member. Although the gathering, processing and displaying of the data is now straightforward, interpretation remains at times rather challenging. This paper provides a brief introduction into the theoretical basis for data interpretation and the hardware necessary for data acquisition. Five case studies are discussed which demonstrate the varied applications of low strain integrity testing of deep foundations and the efficiency at which they are completed. BACKGROUND One dimensional wave mechanics, when applied to a linear elastic pile with a length that is an order of magnitude greater than its width, provides a straightforward basis for the interpretation of motion measurements made at a pile top. When impacted, a stress wave travels through the pile at a wave speed, c, which is a function of the elastic modulus, E, and mass density p (i.e., E=pc2). The applied load F, and particle velocity v, at a point are related by the equation F=Zv. For a cross-sectional area A, the proportionality constant Z is equal to EA/c. Because Z is a measure of the pile's resistance to change in velocity it is called the pile impedance.

Jan 1, 1990

By Michael W. Neill, O&apos

The engineering profession generally does not accept vibro-driven piles as bearing piles unless their capacities can be verified by restriking with an impact hammer, which significantly reduces the economic benefits of vibratory driving. In part, the concern for capacity development in piles driven by vibration arises out of observations that vibro-driven piles do not develop capacities equivalent to those driven by impact (e. g., Mosher, 1987). Nonetheless, if capacities are predictable, vibratory installation may be more cost effective than installation by impact, due to savings in time of installation, even if capacities are lower than those of impact-driven piles. Throughout the past few decades, a number of attempts have been made to develop capacity prediction methods for vibro-driven piles, mostly along the same lines as methods for impact-driven piles. That is, (1) totally empirical formulae, (2) power balance / power transfer formulae, and (3) "time domain-nonlinear" (TDN) computational procedures such as the wave equation. Some of the formulae have been based partly on field experience, but the majority have been developed from simple theoretical models with parameters evaluated from laboratory studies. Neither these formulae nor the TDN solutions have been systematically checked (or modified) by recording appropriate field data over a variety of site

Jan 1, 1989

By Sheryl D. Gallagher

The project consisted of filling an abandoned underground limestone mine to facilitate construction of a new entrance ramp to I-470 in Lee?s Summit, Missouri. Due to collapse of mined areas near the project site, design included determination of the limits of remediation for the project and minimum construction requirements for mine infilling. The Judy Company, contractor selected for the mine infilling, experimented in the laboratory with several grout mixes to determine the appropriate mix for the project. Infilling was accomplished from the ground surface, and camera observation was used to monitor the barrier wall construction and infilling process. It was discovered that some of the mapped rooms were larger and some were smaller than indicated on the construction plan.

Jan 1, 2009

By Inn-Joon Park

Major problems associated predicting soil-structure interaction behavior are based on the fact that soil is neither homogeneous nor elastic and soil properties are spatially variable. There also exist significant coupling problems between the behavior of the structure and geologic media. When designing foundation or other geotechnical structures, the load transfer between the soil and structure takes place at the contact surface. This surface is called the interface. The behaviors of interface play an important role in the load-deformation response of soil-structure interaction systems. The purpose of this study is to develop improved model for simulation of saturated sand-steel pile interface behavior based on a general concept, called the disturbed state concept (DSC), which can characterize the behavior of saturated soils under dynamic loads. In this study, the Disturbed State Concept (DSC) constitutive model is calibrated and modified for steel pile-saturated sand interface and interaction by using the continuous hardening model for relative intact (Rl) state and the critical state model for the fully adjusted (FA) part in the saturated sand material. The general formulation for implementation has been developed. Then, the DSC model with modification for interface and saturated sand is implemented in finite element program based on the generalized Biot's theory. The interface tests under one-way monotonic and two-way cyclic loading and cyclic triaxial tests are executed for defining the parameters for interface and surrounding soils. Based on these parameters, steel pile-saturated sand interface and interaction are numerically simulated using the finite element program modified in this study. The DSC predictions show improved agreement with the observed results from laboratory test.

Jan 1, 2002

By Gregory A. Stephan

A case history of design, prediction, probe pile driving, and construction of a pile foundation for Building 3 of Waterside at Bay Beach Condominiums located in Fort Myers Beach, southwest Florida, is presented. Site geometry constraints, the presence of a 12.0 ft (3.6 m) deep lake occupying the southern one-third portion of the proposed building footprint, and marginal subsoils provided specific challenges for design and construction of the foundation. The subsoil conditions were explored by performing Standard Penetration Test (SPT) borings and a Piezocone Penetration Test (PCPT) Sounding to depths of 100 ft (30.5 m) within the building footprint. Additionally, borings were performed to envelope the building. Deep foundation alternatives included driven concrete, monotube, and steel pipe pile as well as drilled shaft. Following an evaluation of high structural loads, site-specific constraints, foundation test data from buildings 1 and 2, and preference expressed by the project owner, a pre-cast prestressed concrete (PPC) pile-supported foundation system was selected as an economical and effective foundation approach. Use of an augered cast-in-place (ACIP) pile foundation system was precluded by the project structural engineer. This paper deals with the design aspects and methodologies utilized in choosing and economizing the foundation system. The building foundation was designed for an allowable pile capacity of 40 tons (353 kN) in compression, 1.5 tons (12 kN) in lateral capacity for a deflection of 0.25-in (0.64 cm) and 15 tons (133 kN) in uplift capacity. For the single story extended garage structure, a pile capacity of 27 tons (238 kN) was indicated in compression. As part of the design process, an extensive probe pile driving program was carried out in order to evaluate the pile driving equipment, determine and verify pile capacities, and optimize the production pile lengths. A total of 33, 14-in (356 mm) square, PPC concrete piles were driven within the entire building limits, and dynamically load tested utilizing Pile Driving Analyzer (PDA) as part of the probe pile driving program. Utilization of PDA during probe pile driving helped in predicting pile set-up (i.e., increase in pile resistance with time) as well as reducing the pile lengths by as much as 20 percent. It resulted in variable pile lengths during the production phase. This information was effectively utilized as part of the overall quality control program to install a total of 559 PPC piles (including 33 probe piles) within the Building 3 footprint, including the reclaimed lake area, to depths ranging from 45 to 58 ft (14 to 18 m) below existing ground elevation as part of the foundation support system. Prior to installation of probe or production piles, a termination criterion was established using 1-dimensional wave equation analyses in addition to the design pile embedment requirement. The predicted pile capacities compared reasonably well with the capacities from the CAPWAP analyses for probe piles. This engineered, monitored and tested foundation solution provided a cost effective and satisfactory basis for completion and approval of the foundation work for the building resulted in cost savings over other foundation alternatives for the owner. The building has since been occupied and a recent reconnaissance has indicated that the building foundations are performing satisfactorily.

Jan 1, 2003

By Timothy L. Roberts

For many years practicing geotechnical and structural engineers in Texas and Louisiana were reluctant to include augered cast-in-place (ACIP) piles as a viable deep foundation alternate. Three primary concerns were the lack of a final driving resistance to confirm adequate capacity, the inability to inspect ACIP piles prior to installation, and the fact that pile integrity is highly dependent on the skill of the ACIP pile contractor's field personnel. The Deep Foundations Institute (DFI) Committee on Augered Cast-In-Place Piles has responded to these quality control concerns by establishing standards of practice for ACIP pile installation and ACIP pile inspection. Regional areas of the country have different subsurface soil and rock conditions and many times this will influence local installation and inspection requirements. The best way structural and geotechnical engineers can address quality control concerns is to be familiar with the DFI standards of practice, to know the special requirements for a particular project site, and to incorporate them into a well-written ACIP pile specification. The purposes of this paper are to: 1) review the main fundamentals of a successful quality control program, 2) describe how these fundamentals can be applied to the installation of ACIP piles, and 3) add personal experiences from ACIP pile projects in Texas and Louisiana. Nondestructive test methods are frequently used as a quality control tool to evaluate questionable piles. An additional brief discussion of two nondestructive test methods is presented to complete the paper.

Jan 1, 1998

By Bengt H. Fellenius

Session 2, Deep Foundation without Soil Excavation, has attracted no fewer than 22 papers dealing with subjects from soil improvement by grouting, injection, and deep mixing techniques through vibroflotation and special piles, including aspects pertaining to conventional driven and bored piles. In the short time available, it is not possible to both do justice to the papers and provide a critical review of the state-of-the-art. Instead, to meet the objective of making the next half hour worthwhile to the audience, I have chosen to comment on a few special points brought forward in the papers and thereafter to discuss more in detail a couple of aspects I have deemed to be of general interest. Four papers deal with jet-grouting, injection, and deep mixing techniques: DOMSKI, J. J. Reinforcement of subsoil under the foundations of historical buildings in Cracow using deep injection technique. RESTELLI, A. B, BERTERO, M., and LODIGIANI, E. Deep mixing technology to improve the bearing capacity of a very soft clayey soil under an earth embankment.

Jan 1, 1994

By B. Ramanathan

The results of a pile load test on a 1200 mm dia and 25 m long bored Cast-in-situ pile in soft rock is reported. The subsoil has a high N value of above 60 from 7 m to 21 m. The soft rock was observed below 21 m and N value exceeded 100. The theoretical calculations showed that the safe carrying capacity will be about 410 t. But the actual load test on the pile indicated that the allowable load is only about 140 t. This is attributed to the fact that the soil is cemented and loses strength due to remoulding caused by pile installation. It is concluded that great care should be exercised in determining the carrying capacity of piles in cemented soils and soft rocks and that 'N' value alone should not be used.

Jan 1, 1996

By Michael J. Brown

It is often necessary to undertake some form of pile testing to verify design calculations. Historically this has been limited to static and dynamic tests. Newer rapid testing methods such as Statnamic are seeing more frequent use. This form of testing can be advantageous due to short set up time and test duration. Although the methodology suffers from a lack of formalised guidance and may prove difficult to analyse in certain soil conditions. This paper investigates the suitability of Statnamic testing and analysis for a range of soil and pile types as well as different installation methods through a number of case studies undertaken in the UK. Recommendations are made on test specification and analysis.

Jan 1, 2006

By Chris G. Leach

"Abstract A seven storey Northbridge area of Perth, Western Australia presented residential apartment complex located in the an opportunity for a novel application of Cutter Soil Mix technology (CSM). The development included a two-level basement for car parking which covered the full site area. However, the basement was also required to extend under an existing single story heritage building. Soil conditions comprised 2m of fill overlying medium dense to dense sands that in turn were overlying a very stiff clay stratum at approximately 14-16m depth. The ground water table was located at a depth of approximately 1m below the natural surface level.A site boundary consisting of a reinforced CSM retention system and was designed and installed to allow the excavation to proceed to basement level. Two rows of temporary soils anchors or inclined struts were required to achieve this. A CSM support system for the heritage building was also designed and constructed to provide temporary support during excavation and permanent construction works. The brief for the contract works emphasised that it was vital that settlements of the heritage building be kept within strict limits.CSM is a relatively new introduction to the Australian construction market, using a modified trench cutter to mix a binder slurry with in situ soils, generally to form cut-off walls, retaining walls and soil improvement works. This project is understood to be first application of the CSM for underpinning work in Australia.This paper discusses the site background details leading to the decision by the client to adopt CSM technology, and the design and construction aspects to meet the challenges offered by this project.Introduction190 Newcastle St is a 7-level residential apartment complex located in the Northbridge area of Perth, Western Australia. The development includes a 2 level basement for car parking, which covers the full site area. The basement also extends under a single story heritage building, which remained in-situ throughout the building works.A site boundary retention system was required to allow the excavation to basement level to proceed. In addition, a support system for the heritage building was required to provide temporary support during excavation and permanent construction works."

Jan 1, 2014

By Jeffrey A. Schaefer

The Olmsted Locks and Dam project is located on the Ohio River approximately 16.5 miles upstream of its confluence with the Mississippi River. It consists of twin 1200 ft. locks with floating and fixed approach walls, five 110 ft. wide tainter gate bays, a 1400 ft. wide navigable pass boat operated wicket gate section, and a 400-ft. section of fixed weir (Fig. 1). The project will have a total cost over 1.0 billion dollars, and as such is one of the largest civil works project underway in the Corps of Engineers.

Jan 1, 2001

By Grant R. J. Bearss

Due to environmental concerns in urban construction, many typically simple projects become very complex or feasibly impossible. The introduction of relatively new concepts has redefined "impossible", again simplifying these projects and making them "possible". Case Study One covers the use of Pressed-in Tubular Piles on portions of the Long Island Expressway in Queens, New York. Innovations in the design, material and installation method solved many typically inherent problems on projects of this type and resulted in cantilevered walls that supported a 35ft (10.668m) excavation. Design predictions and actual measured deflections of this wall were within millimeters. Case Study Two covers the use of Pressed-in Tubular Piles on portions of the Hodogaya Bypass in Yokohama, Japan. Innovations in equipment development allowed for a cantilevered retaining wall to be constructed without affecting the adjacent right-of-way, dramatic reduction of the overall construction duration and installation of tubular piles in soils with SPT N values greater than 160.

Jan 1, 2002

By William S. Heckman

a. When to use: high surcharges, vertical capacity required, limit noise and eliminate vibrations, low headroom, eliminate vibration induced settlements. b. Advantages: eliminates impact noise and vibrations, high section modulus if required, vertical load bearing capacity; corrosion resistant, easy to apply facing for use as a permanent wall, adapts to complex wall layouts, would allow top- down construction, very high uplift resistance. c. Disadvantages: spoil disposal, not water tight, cannot penetrate rock and most obstructions, soil can erode between the piles if surface water and ground water are not controlled, hard to install reinforcing beams over 409 long; subject to high negative skin friction loads, high grout takes in rubble and organic soils. e. Relative cost to other systems: 30% to 50% more expensive than driven soldier piles and lagging except when surcharge loads are involved, or the pile cannot be driven due to noise and vibrations. About the same cost as a sheet pile system. Very competitive if high vertical load must be supported by the wall.

Jan 1, 1997

By Wolfgang G. Brunner

The closing of the gap in the European waterway- net is one of the big and challenging traffic projects following the German reunification. The water canals in the North German plain connect the Rhine river, the border between Germany and France, with the Oder, the German border river to Poland. As early as in the 30's of the 19th century the planning and construction of a ship- lift and a canal bridge started, in order to close this last big gap in the system between the Mittelland Canal and the Elbe- Havel Canal near Magdeburg. This main waterway connects the West of Germany, known for its coal mines and steel mills, with the capital Berlin, and from there it goes on into Poland. The building activities started in 1934 but came to a complete stop in 1942 because of the war. The communist government in East Germany was not interested in continuing this huge project, including the ship lock Rothensee, the canal bridge crossing the river Elbe, the former border river between West and East Germany, and the lock Hohenwarthe due to lack of political backing along with low construction capacity.

Jan 1, 2000