Search Documents

By J. K. Van Beek

The Deep Underground Science and Engineering Laboratory (DUSEL) is a scientific facility that will be placed in the deeper reaches of the Homestake mine, Lead, SD. Our team of geologists and engineers is carrying out the first scientific project awarded to the site ? Towards a Transparent Earth. Taking advantage of the thousands of open exploratory and sand-line holes, we are installing the beginnings of a seismic observatory. Each installed station consists of a 3-D accelerometer package and a 1 nanoradian 2-D tilt meter. In order to allow for a variety of monitoring and characterization studies, the array instruments are sensitive over the frequency bandwidth of 0.2 - 1 KHz. Three, three component accelerometer stations are currently installed ? in a 140 m deep bore beneath the slurry pump house, and in 12 m deep bores on the 2000-foot level, 800 and 400 m from the Ross shaft. There is a tilt-meter installed at each 2000 level station. These installations are in 150 mm diameter sand-holes. From the currently installed tilt sensors we are investigating solid earth deformation as a response to tidal potential. The accelerometers are being used to locate and characterize events associated with mine dewatering and rehabilitation.

May 1, 2009

By P. Woo, N. Brodusch, R. Gauvin, H. Demers

The scanning electron microscope (SEM) was primary developed for imaging applications. With the introduction of the Si(Li) energy dispersive spectrometer (EDS), simultaneous imaging and x-ray microanalysis became possible. However, long working distance and high current were needed because the position and small solid angle of the EDS detector. The high spatial resolution is generally obtained at short working distance with a SEM. Unfortunately x-ray microanalysis is never performed in the best imaging conditions. The annular silicon drift detector system is inserted below the objective lens which gives a higher solid angle (up to 1.3 sr). In consequence, a lower working distance and probe current can be used. An improved spatial resolution becomes possible during x-ray microanalysis. With this x-ray detector installed on a cold-field emission scanning electron microscope, quantitative x-ray microanalysis with high spatial resolution at low beam energy and low current becomes possible with the possibility of using the various different type of imaging at the same time. Also, since the count rate can be as high as 1,500 kcps, which lowers significantly the detection limit of elements as well as the minimum feature sizes of different phases that can be distinguished.

Jan 1, 2014

By Jiahao Xu, Namsoo P. Kim, Guikuan Yue

Iron (ferrous ions and ferric ions) plays an important role in the heap leaching of copper sulfide minerals and copper electrowinning. In our previous study, a novel oxidation-reduction potential (ORP) equation only based on the variables of temperature and nominal ferric/ferrous ratio was developed to predict the redox potential of the quaternary H2SO4-Fe2(SO4)3-FeSO4-H2O system, and its applicability was also extended to more complex acidic iron sulfate solutions, especially those generated during the acidic leaching and bioleaching of Printed Circuit Boards (PCBs) to recover copper. In this work, the broader range of applicability of this equation to other complicated acidic iron solutions containing copper ions has been extended and determined. Specifically, synthetic iron-containing solutions with copper ions according to the conditions of industrial electrolyte during copper electrowinning and heap leaching have been used to measure the ORP and test the developed equation. It seems that this equation can still be employed to predict the redox potential of the Fe3+/Fe2+ couple for the simulated solutions under conditions related to copper electrowinning and pregnant leaching solution generated during heap leaching over a wide range of solution concentration, nominal Fe3+/Fe2+ ratio and temperature. It has shown that the prediction and measurement of redox potential is highly useful to estimate and understand the iron chemistry of industrial leaching and electrowinning processes. INTRODUCTION It is well-known that iron (ferric or ferrous) ions are widely involved in the hydrometallurgical production of non-ferrous metals such as Cu, Au and Zn, mainly in the form of acidic iron sulfate solutions. As far as Cu is concerned, in a typical leaching-solvent extraction-electrowinning process, ferric ion plays a central role in the heap leaching process and is reduced to ferrous ions in the pregnant leaching solution. Ferric ion is the most important surrogate oxidant and the dissolved ferric/ferrous couple plays an important catalytic role in accelerating the leaching rate with oxygen as an oxidant (Peters et al., 1986; Schlesinger, King, Sole, & Davenport, 2011). In addition, during the traditional electro-winning process, oxygen is evolved at the anode, and copper is reduced at the cathode. A common idea is that iron in the electrolyte in copper electrowinning cell (with total iron of 1–4.4 g/L) plays an important role in reducing the current efficiency. According to the published results (Winand et al., 1975; Dew et al., 1985; Moats et al., 2009; Khouraibchia et al., 2010), thecurrent efficiency decreases linearly with increasing ferric ion concentration and the energy consumption increase was mainly caused by the decrease in current efficiency.

Jan 1, 2019

By P. Bonadia, A. Tabereaux

Nearly all aluminium smelters are increasing the potline amperage to achieve higher aluminium production. In some instances the higher amperage operation has a significant negative impact on shortening the lifetime of aluminum electrolysis cell cathodes due to loss of the protective sidewall cryolite ledge freeze and too rapid penetration of the cell bottom refractory lining by cryolitic bath components due to the higher temperature isotherms. Thus Cathodes require careful thermal modeling of the cathode relining designs and improved refractory materials to allow greater heat loss from the sidewall to preserve a stable sidewall ledge freeze at higher amperages, and the selection of optimum refractory barrier materials to control the penetration and reaction of bath into the cathode bottom refractory and insulation lining. This requires an understanding of the reaction mechanisms and product formation for molten NaF enriched bath and alumino-silicate refractories. It is desirable to use dense, low porosity refractory fireclay firebricks, or similar materials with a sufficiently high silica content to promote the formation the mineralogical phase albite, NaAlSi3O8, that significantly increases the viscosity of the melt which slows the diffusion of reactive species in the melt and thereby retards further bath penetration.

Jan 1, 2004

By M. Fooladi Mahani, M. R. Izadpanah

The knowledge of the thermal shock resistance of refractory materials is of outmost importance due to their wide range of applications in various industries, namely; ceramics, oil refinery, thermal insulation, nuclear power, chemical and petrochemical industries. Thermal shock resistance is measured in terms of the number of cycles that a refractory material can withstand when subjected to sudden temperature changes. This property is measured experimentally by heating a sample of the material and cooling it in a known environment then the number of cycles it withstands this treatment without spalling is a measure of its thermal shock resistance. Although this method of experimentation has long been the practice, but it is both expensive and time consuming. Various studies have been carried out to predict this vital property, however, the rang of applications are limited. The present study employs a test rig by which temperature distributions in magnesite samples are accurately measured. This information plus other results obtained from relevant tests on related properties are used to develop a model which predicts the number of quench cycles withstand by different materials when subjected to sudden temperature changes. The comparison of the theoretical values using the solution of the presented model with experimental data for different materials having different thermal resistance shows a closed agreement.

Jan 1, 2004

By Tiago Webber

Mineral resources estimation comprises basically two stages: (i) data collection, analysis and validation, and (ii) the estimate of the grades and tones of the deposit. The most applied method for sampling survey in mineral exploration is rotary drilling with total core recovery. High drilling costs make borehole geophysical logging attractive to obtain the maximum possible information from each borehole helping to understand ore intersections, grades variability, limits of the deposits and continuity of the mineralization. In this paper, borehole geophysical logging was used to enhance the sampling survey and to derive grades indirectly (without lab analysis) with a certain amount of uncertainty. Indicator kriging (IK) was the estimation method used, as it is adequate to incorporate the uncertainty associated with the geophysical derived grade values. The results were compared to the conventional procedures using grades determined via core analysis and ordinary kriging. Borehole geophysical logging proved to be efficient to define the essential features of ore deposit and IK provided results with acceptable precision and accuracy if compared to the model provided by ordinary kriging.

Oct 1, 2009

By D. J. Bowen

"The Great Dyke extends for 540 krn along strike, to unknown depth, and varies in width from 3 krn to 11 krn. Rb/Sr age determinations gives values of approximately 2470 Ma.The Dyke consists of a variety of mafic and ultramafic rocks, many altered to serpentinites. These include, from top to bottom, successions of gabbro/norites, pyroxenites, peridotiteslharzburgites, and dunites/picrites.The layers dip in from either margin, steepest at the edges (20°) and flattening toward the central sections. Four separate complexes are present. From north to south these are termed the Musengezi, Hartley, Selukwe and Wedza Complexes, and are described as 'boat-shaped' or 'pig-troughed'. All are similar in petrological sequences. Physiographically, the Dyke is spectacular in the north, where as a mountain range it meets the Zarnbezi Escarpment. Elsewhere in the central parts there is little surface expression and wide open treeless vleis. Dyke rocks cut through granite and schist belt terrain and are termed 'The Magnesia Belt'.Vast mineral resources exist. These include chrome, asbestos, platinoids, nickel, copper and gold. Up to eleven chrome seams numbered from top to bottom occur in the lower ultramafic sequences. Seams are narrow at 10 em to 30 em but of high grade. The platinum occurs 10 m to 40 m below the norite/pyroxenite contact.A 60 m wide zone of Light Sulfide Mineralization (LSM) of less than 1070 sulfides extends from the lower gabbronorites into the upper pyroxenites. In this LSM, four enriched zones carry up to 5% sulfides. The most widespread is termed the Main Sulfide Zone (MSZ), below which is No. 2, No.3 and No.4 Sulfide Zones. The MSZ carrying pyrite, pyrrhotite and chalcopyrite is a multielement ore with components of PGE (pt-Pd-Rh), nickel, copper and cobalt, and gold and silver.Extensive exploration programs have been carried out and the intention is to begin large-scale mining. However, with Russia supplying metals to the western markets, South Africa's cutback on production, and an end to the Cold War, delays have arisen."

Jan 1, 1994

By R. M. Graves, C. B. McKenzie, D. Barbour, D. W. Desnoyers

"The prospective Tulks volcanic belt hosts five significant massive sulfide deposits, Tulks Prospect, Tulks East, Jack's Pond, Daniel's Pond and Victoria Mine, as well as numerous showings and indications throughout its 70 km outcrop length. Regionally, the 498 Ma sequence consists dominantly of felsic pyroclastic rocks and flows with interbedded mafic volcanic units and finegrained sediments, commonly graphitic. Contemporaneous granitoid rocks occur in the south half of the belt. Rocks usually display a strong NE-SW, steeply dipping, penetrative foliation and other shear-related high-strain fabrics. Facing directions are normally northwest, although there is local evidence of folding. Sulfide bodies and their alteration systems are deformed and shape-modified in the style of ambient strain.The Tulks, Tulks East and Jack's Pond prospects appear to occupy a similar stratigraphic level, on or near the contact between a thick felsic pile and an overlying broad, conductive package of graphitic sedimentary rocks. All are pyritic deposits with well-developed footwall alteration systems. The Tulks prospect comprises four polymetallic lenses totalling 750 000 t. Three lenses constituting more than 6 000 000 t of sulfide mineralization are indicated at Tulks East but only the 210 000 t ""B"" lens contains significant base metals. Jack's Pond consists of a very extensive, zoned alteration complex in which four lenses of massive to semi-massive pyrite + chalcopyrite are known. The central part of the system, characterized by Mg chlorite and carbonate, is enveloped by pervasive sericitization and capped by intensely silicified and pyritized volcanics. The sulfide lenses are interpreted as part of the footwall zone and are beneath that part of the system most likely to hostpolymetallic massive sulfides.Daniel's Pond differs from the other prospects in such fundamental ways as metal content, associated alteration and structural setting. The deposit comprises strongly tectonized, Ag-rich, Zn-Pb mineralization distinguished by a pronounced Ba-As-Sb signature. Mineralization is confined to a narrow, north-south high-strain zone which separates unstrained mafic volcanic rocks to the east from well-foliated felsic rocks. The deposit lacks an extensive alteration halo and at its north end is associated with a lens of barren, undeformed massive pyrite.The Victoria Mine deposit, the most cupriferous of the five, is related to a moderately dipping structure that separates well-foliated Tulks volcanic rocks from an overlying, less deformed volcanic sedimentary sequence that may be as young as 462 Ma. The structure is also the locus of black chlorite, dolomite and quartz alteration. Structurally remobilized precursor sulfide mineralization is one possible source for the deposit."

Jan 1, 1993

By Barbara Kirby

Mining Industry HR Challenges Mining industry needs to hire approx. 100,000 workers by 2020 Attraction and retention of talent in all occupations Mobility of skilled workers between mine sites 70 percent of employers expect labour shortages over the next 5 years. Largest shortages: -physical sciences and engineering occupations -trades and ?undesignated? occupations ?Undesignated? Occupations ?Undesignated? Occupations -eg. mill operators, production / development miners and heavy equipment operators More than 20,000 workers will be needed by 2020 in the undesignated occupations and another 11,500 tradespersons Turnover rate for trades and undesignated occupations at mines is high: 8.3% compared to 5.6 % for all other occupations There is no system to recognize the skills of high-demand undesignated occupations

May 1, 2010

By Christopher Sherman

The engineering properties of a geologic material are greatly affected by the presence of macropores. Previous research has demonstrated that the size, location, and proximity of macropores influences both the strength and stiffness of specimens. Knowledge of the distribution of macropores in a specimen prior to testing would be useful for a number of reasons. We are developing a non-destructive method called cross-specimen acoustic tomography (CSAT) currently to determine some (or all) of the macropore characteristics for a laboratory specimen. The CSAT method uses a set of piezoelectric sensors that generate and receive high frequency acoustic waves. We measure the travel times of the acoustic waves through a specimen and then use a commercially available tomography software package to invert the data. The inverted velocity model is then used to locate the voids within the specimen. Two dimensional (cross-sectional) results from plaster specimens containing large macropores of Styrofoam show the technique is promising and worthy of further development.

May 1, 2009

By Te Gao

It is a general expectancy that in most of the construction and renovation project, the contractor is going to hand over the as-built documents to the owner or the facility management team at the completion of the project. The main challenge for the handover process is to ensure the completeness of the captured building information and the accuracy of it in terms of how well it represents the reality. Building information models (BIMs) can be used as an information repository to store and deliver as-built information. However, due to changes made in the construction and renovation phases and errors made in the design and modeling phases, discrepancies can exist between BIMs created in the design phase (asdesigned BIMs) and actual building conditions. Laser scanning technology is able to efficiently capture accurate geometric information, which provides an opportunity to identify and quantify discrepancies and update as-designed BIMs into as-built BIMs. This paper presents a case study, within which the asdesigned BIM of a newly renovated research lab was updated into an as-built BIM using laser scanned data captured in the renovation phase. This paper introduces the challenges associated with the updating process for the as-designed BIM. In order to address these challenges, this paper introduces a framework that supports the update of an as-designed BIM by incorporating point clouds captured by the progressive laser scans.

Aug 1, 2013

"INTRODUCTIONThe Department of Energy, Mines and Resources has recently developed two automatic controls for use in the cyanidation circuits of Canadian gold mills. These controls are the alkalinity probe and the Continuous Cyanide Titrator both of which are discussed in the paper ""Instrumentation in the Cyanide Process"".(1)In May 1966 these process controls and associated recording equipment were installed in the Bralorne mill by two Scientific Officers from the Department. The object was to determine if the equipment was amenable and applicable to this particular circuit. The purpose of this paper is to discuss the performance of the equipment over a test period of 4 months.CONCLUSIONSThe results of test work to date indicates that both the Conductivity Probe and the Continuous Cyanide Titrator would be an as set to the operation of the Bralorne mill.The conclusions are generalized as follows:-(1) At a milling rate of 100, 000 tons per year the expected reductionin reagent consumption would give a direct saving of 37, 660 lbs of lime@$0.030 per lb and 15, 790 lbs of sodium cyanide@ $0.175 per lb. Such cost savings would pay for the equipment and installation costs within a 30 month period"

Jan 1, 1967

By J. Chlan

"Dryer DescriptionProctor and Schwartz Continuous Conveyor DryerThe Proctor and Schwartz Continuous Conveyor Dryer has been in operation since July 1958, and comprises six unit• - an 8• wide single conveyor with roller extruder, insulated housing, type 304 stainless steel circulating and exhaust fall system, steam heating coils, temperature controls and discharge crusher rolls. Entire dryer dimensions are 52’ x 12'0""weighing 53,000 lbs,Extruder rolls - setting is 1/8"" (Drive 3 HP 1800 RPM) clearance off the extruder screen.Conveyor - consists of 151 interlocking pans, measuring 8"" x 8' (2 HP 1200 RPM) One Exhaust Fan (5HP - 900 RPM)Steam Coils -- l"" steel pipe - with steel fins -- each coil measures 16' 2’’- 64 coils in the No, 1 Compartment- 64 coils in the No, 2 CompartmentDryer OperationThe yellowcake slurry at 28% solids is pumped to an 81 x 8' Peterson Filter. The filter media presently being used is a Neotex 4372 blanket, being 100% staple fibre nylon, 12 oz per square yard with air porosity of 9 CFM's. The cake discharge at 45 - 50% moisture falls into the roller extruder. Extrusions are formed by forcing the material by rolls through a perforated plate moving back and forth and depositing the spaghetti-like extrusion on onto the dryer-conveyor.The conveyor now carries the extruded material through the heating chamber•, The feed end of the dryer will be referred to as No. 1 Compartment, with temperature control set at 280""F. The circulating fans take the hot air off the coils and circulate the heated air through the perforated openings in the dryer conveyor pane, After passing through the set of steam coils and circulating fan in No, 1 Compartment, the material then goes through No, 2 Compartment where the temperature is set at 305'F, Final material then discharges through a set of crusher rolls set at ~"". Moisture of final dried product runs at less than 2%.The dryer conveyor load is usually run to a 3"" - 4"" depth load. Conveyor speed at approximately 90 minutes for load to pass through. Load onto the conveyor is controlled by boot level and speed of the 8' x 8' filter. The dryer steam coils are water-washed twice a month."

Jan 1, 1972

By Caitlyn J. McKinley, Ahmad Ghahreman, Maziar E. Sauber

Ever-growing global needs for critical metals, such as rare earth elements (REE), and base metals, such as copper and nickel, and their environmental impact motivated the pursuit of sustainable flowsheets. Regeneration of hydrochloric acid in chloride-based leaching flowsheets as a critical unit operation is an example of such endeavours. This study presents an efficient hydrochloric acid regeneration method from a magnesium chloride solution waste by addition of sulphuric acid in relatively low temperatures. The effects of temperature, initial magnesium chloride concentration, amount of sulphuric acid added, and airflow are examined. Experimental work are focused on temperatures between 80 and 95°C, initial magnesium chloride concentrations of 2 to 5 M, 100% to 220% stoichiometric sulphuric acid additions, and airflows between 200 to 600 mL/min. The developed technology recovers hydrochloric acid at a high rate and concentration with a relatively small environmental footprint. INTRODUCTION The mining and metals sector is under increasing environmental and economic pressure to make more efficient use of chemical reagents and energy in the production process. This affects several areas of process and flowsheet design such as the selection of the most appropriate unit operations and the overall design of the process steps paying heed to sustainability. Owing to the inherent inefficiencies of physical and chemical processes used in the mining industry, there will be materials and streams generated that are not a desirable part of the envisaged flowsheet. Thus, methods are implemented to recover and recycle such effluents. If the recovery and recycling are not economical, then procedures are followed to neutralize and dispose these effluents. In many cases, these effluents are potential contaminants or hazardous materials, and their disposal should be looked at in a much larger context. The safe management of the contaminants and hazardous effluents is a daunting problem in the mining industry and is fraught with technological, economic, social, and political challenges.

Jan 1, 2019

By Jeffrey D. Eisenman

FRP is a proven material for the solvent extraction processes of copper production. There is a history of successful applications of FRP piping and equipment in hydrometallurgical processing. The performance of FRP equipment has not always been consistent, but at no fault of the material. Its non-metal attributes and behavior vary from those of more typical materials of construction, such as steel and alloys. FRP is a mainstay material in many areas of solvent extraction and electrowinning and yet not well understood by all. We will discuss the critical concerns, which are key to reliable performance of FRP systems. This paper will include discussion of key elements, which are fundamental to reliable FRP piping design and considered best practices. Essential design and construction considerations to maximize reliable service life of FRP equipment, such as thickeners and process vessels, used in copper extraction and processing, will be discussed. Additionally, we will expose potential pitfalls and share lessons learned from previous copper processing plant projects, which can aid and impact other copper processing projects to ensure best system performance and reliability. INTRODUCTION The corrosion resistant attributes of fiberglass reinforced plastics (FRP) make it an attractive and cost effective material of construction in corrosive service applications that are found in copper processing. FRP is used all over the processing plant in seawater, brine and sulfuric acid services where the corrosive nature of these services would challenge most ferrous materials and coatings. FRP is a fully customizable material to meet the specific needs of each service and process. FRP piping and equipment can be found throughout the hydrometallurgical process, in the acid plant, desalination, leaching processes, solvent extraction and electrowinning to name a few. Beyond its superior corrosion resistant characteristics, FRP can be made abrasion resistant by introducing particulate additives into the resin, such as silicon carbide and alumina oxide. Because many of these services have combustible organic elements in the flow streams with accompanying safety concerns, the linings can be made conductive with carbon fibers to dissipate static charges that might collect on the surface of the equipment otherwise. Further, FRP can be made flame retardant as well, where flammability may be of concern.

Jan 1, 2019

By Sarah Bélair, Denis Beltrami, Deka Moussa Ragueh, Valérie Weigel

"Scandium is a highly valuable element belonging to the rare earth elements (REE) but it has different chemical and physical properties from those of lanthanides. This metal is generally used in aluminum-scandium alloys and in fuel cells but the development of its market is slowed down by its high price (more than 1000 US$/kg for a 99.0% grade product). Indeed, the low scandium content in the continental crust (an average of 22 ppm) and the difficulties to extract it selectively from solutions containing high impurity concentrations increase the cost of the recovery processes. Nowadays, scandium is primarily recovered as a byproduct.ERAMET is developing a hydrometallurgical process in Gabon (Mabounié) in which the scandium content in the deposit reaches 10 to 100 ppm. The Maboumine project consists in the extraction and purification of uranium, niobium, tantalum and REE from Mabounié ore. In the frame of this hydrometallurgical project, ERAMET had also studied the feasibility to recover scandium as a byproduct. During the ore leaching, uranium and rare earth elements including scandium are solubilized into the pregnant leach solution (PLS). Among the various methods investigated to recover scandium from the PLS, liquid-liquid extraction using Primene JM-T as extractant was chosen and tested first at laboratory scale and then at pilot scale. Selective stripping of the loaded organic was carried out by using phosphoric acid solution, allowing the selective recovery of scandium from thorium and zirconium partially extracted from the PLS by Primene JM-T under the process conditions."

Jan 1, 2016

By S. Zakaria

"Inco's Automated Haulage Truck System (AHT) is a revolutionary automatic guided vehicle that performs all load, haul and dump operations without human intervention. The high level of sophistication and the short period it has been in operation has only allowed a select few Inco personnel to become familiar with the ART operation and maintenance. As an aid to operations an expert system using the knowledge gained from the experienced specialists was implemented in the field.The AHT operating and maintenance assistance expert system will reason through the information given, arrive at conclusions and give advice to operations, technical and management personnel. It will provide comprehensive real-time troubleshooting assistance for the hydraulic, electrical and mechanical subsystems of the ART. The ART expert system has many benefits to Inco which include increased skill levels of ART operations and maintenance personnel, reduction in ART downtime, standardization of troubleshooting procedures and reduction in ART operating and maintenance costs. In the future, the expert system application will be linked to SCADA (Supervisory Control and Data Acquisition), maintenance and statistical software to display current and historical trends of variables from a centralized historical database. As well, a wide variety of features will be integrated into the system including AutoCad drawings, graphics, photographs, voice and video capabilities."

Jan 1, 1994

"The Dome Mine, located in South Porcupine Ont. has been in operation since 1910 and is owned and operated by Placer Dome Inc. The current milling facilities were constructed in two phases with the first being commissioned in 1982. It consists of a grinding, gravity separation, thickening, and leaching circuits. The second phase was commissioned in 1988 with the addition of the CIP, stripping, electrowinning, and carbon regeneration circuits.It is now common practice in the gold processing community to add liquid oxygen to leach circuits to increase both recovery and kinetics. Along with these benefits the metallurgical group at the Dome realized the potential to replace compressed air with liquid oxygen as a source of oxygen for the dissolution of gold. A plant trial of liquid oxygen was undertaken during the fall of 1991. The results of this first test were favourable enough to warrant further investigation, and a second plant trial was conducted in December 1991.The data generated as a result of each trial revealed that oxygen could be economically substituted for compressed air as a source of dissolved 02. The energy savings in required horsepower enabled a rapid payback period. Thus the project was approved in the spring of 1992 and l should be operational during the final quarter of 1992. INTRODUCTIONIn a continuing effort to reduce operating costs and improve recovery at the Dome mill it was decided to investigate the feasibility of adding liquid oxygen (02) to the leach circuit. It is now common practice in the gold processing community to add 02 to the leaching process to increase both kinetics and recovery. It was anticipated that an increase in kinetics would allow us to eliminate one or more leach tanks while maintaining acceptable recoveries. The metallurgical group felt that along with these benefits, the potential was also there to reduce power consumption through the reduction in the processing of compressed air which is quite costly (12 cents/1000 cubic feet per minute in 1991)."

Jan 1, 1993

By C. Paulo, W. N. Wheeler, M. Kalin, M. P. Sudbury

Many researchers have tested the addition of various phosphatic materials, including Natural Phosphate Rock (NPR), to mining wastes. It was assumed that iron in the waste would form FePO4 precipitates, restricting oxygen access to pyrite surfaces and reducing oxidation. Phosphate additions were based on stoichiometry (phosphate mass to sulphide content of waste). Although some interesting, positive results were obtained with low dosages, these were considered accidental, not having followed the expected stoichiometry. In 1991, we began experimenting on tailings and waste rock with NPR, postulating that if chemo-lithotrophic microbes on the mineral surface accelerate oxidation, then heterotrophic (oxygen-consuming) microbes would reduce oxidation. All wastes with NPR produced effluents with elevated pH and low metal acidity. Later, microscopic investigations of the rocks found an organic layer on the mineral surface, which was confirmed by independent research organizations repeating experiments with very low NPR mass additions to sulphidic wastes. In 2013, heterotrophs were identified and quantified as they grew on German lignite with NPR. These data conclusively showed that the development of heterotrophic biofilms is a consequence of adding waste NPR leading to a reduction of sulphide oxidation and improved effluent from sulphidic mining wastes. We document our gradual understanding of the effects of NPR on the reduction of sulphide oxidation, covering 23 years of research.

Jan 1, 2014

By T. Cutard, E. Yeugo Fogaing, C. Gault, H. Marzagui, N. Prompt, M. Huger, C. Deteuf

This paper deals with studies made in the field of the French research network PROMETHEREF. Several refractory castables are considered in this program. In the present paper, one of these materials is considered, it is a low cement castable based on andalusite aggregates. A particular attention is paid to microstructural changes during the first heating and on their effects on the high temperature mechanical behavior. Microstructural evolutions have been characterized by the way of dilatometry, scanning electron microcopy and X-ray diffraction. In-situ observations by environmental scanning electron microscopy gave complementary results on these high temperature microstructural changes. They deal with microcrack formation, phase changes, crystallization, liquid phase formation and sintering. By propagation of ultrasonic waves, high temperature continuous measurements of the Young's modulus have been made. Results confirm the existence of microstructural changes and allow to quantify the Young's modulus variations all along specific thermal cycles. High temperature four point bending tests and room temperature tensile tests were made in the same temperature range. Behavior evolutions could be found and interpreted with the help of previously mentioned results.

Jan 1, 2004