Search Documents

By G Anders

The effectiveness of two types of powder used in long-wall slashing was compared. The evaluation of the results can serve as a good example of how the application of statistical methods to underground test data can help to minimize the number of tests to be carried out. The conclusions are stated concisely, including a definite assessment of the reliability of the tests. Introduction AN assignment at the Algom Nordic mine called for a performance comparison between 70 per cent Cilgel B and 75 per cent Dygel in longwall stope slashing, particularly taking into account, in both cases, the build-up of bootlegs as dependent on hole deviation. Stopes were usually 8 to 10 ft. high and inclined at about 17 degrees. Starting from a raise, they were widened by consecutive longwall slashes to 60 ft., and, al-lowing for drift pillars, were approximately 300 ft. in length along the incline.

Jan 1, 1964

By Q. Han

Irradiation of high energy ultrasonic vibration in metals and alloys generates oscillating strain and stress fields in solids, and introduces nonlinear effects such as cavitation, acoustic streaming, and radiation pressure in molten materials. These nonlinear effects can be utilized to assist conventional material processing processes. This article describes recent research at Oak Ridge National Labs (ORNL) and Purdue University on using high intensity ultrasonic vibrations for degassing molten aluminum, processing particulate reinforced metal matrix composites, refining metals and alloys during solidification process, welding, and producing bulk nanostructures in solid metals and alloys.

Jan 1, 2014

By Lawrence Devon Smith

What is a Failed Project? For mining projects, some key indicators of a ?failed? project are: ? Cost is more than it should be (particularly capital) ? Schedule ? It takes longer to build than expected ? It takes longer to ramp-up than expected ? It does not do what it is supposed to do ? Poor performance; output, product specifications; ? Low revenue ? High costs ? No one is happy about it: Management, Shareholders, Bankers ? Does a project fail if it does not meet expectations that were unrealistic and unattainable? ? Caution: Failure may not become evident until years later

May 1, 2010

By Andreea Catalina Gluhoi

The oxidation of propylene and methane has been investigated over two series of Au/MOx/Al2O3 and Au/MIOx/MIIOx/Al2O3 catalysts (M, MI, MII =Li, Rb, Mg, Mn, Ce, Zr). Whereas the effect of the presence of MOx or MOI x/MOII x on the oxidation of methane is relatively small, a large enhancement in activity is observed for propylene oxidation. Synergistic effects have been observed by combining ceria or a transition metal oxide (high oxygen storage capacity) with an (earth) alkali metal oxide.

Oct 1, 2003

By P. C. Holloway, M. J. Collins, K. R. Buban

Historically, there has been little incentive to process copper-arsenic concentrates by leaching, rather than via established smelting operations. However, with ever tightening environmental emission standards and more arseniferous concentrates being produced, increasingly sophisticated and upgraded off- gas handling facilities are required in smelting operations, generating greater quantities of challenging metallurgical dust. In this context, oxidative pressure leaching offers distinct advantages. The current state of pressure leach technology delivers high extractions from copper concentrates, while producing an environmentally stable process residue, without atmospheric emissions of sulphur dioxide or arsenic. However, as was shown in an earlier study, copper extractions and environmental leach residue stability are impacted negatively by arsenic levels above 2.5 to 3.0 wt%. In further studies on pressure leaching of copper concentrates, Sherritt has developed process conditions that allow even highly arseniferous (> 7 wt% As) feed materials to be converted into environmentally stable residues, with excellent copper extractions. At the same time, pressure leach residues can be generated that are amenable to silver recovery via direct cyanidation, without pre-treatment by lime boiling or hot curing. The results of pilot plant test work are discussed. INTRODUCTION As the production of copper has expanded over the years, resource exploitation has extended beyond relatively clean, high grade and easily accessible ores, and copper sulphide concentrates increasingly come with higher levels of contaminants, such as As, Hg, Sb and Bi, and lower copper and sulphide sulphur concentrations. However, as concerns on the impact of the emission of such contaminants into the natural environment have mounted, import/export restrictions have made the trading of copper concentrate more difficult, and, in particular, the export of concentrates with greater than 0.5 wt% As; under ever tightening environmental emission standards, these lower quality concentrates can be a significant strain on the off-gas handling facilities in smelting operations. The processing of arsenic bearing copper concentrates is, therefore, an increasing challenge as copper producers seek to exploit more complex mineralization and to extend the life of their operations. In this environment, processing arsenical copper concentrates with high temperature pressure leaching (>200°C) must be considered as an alternative to pyrometallurgical processing. Leaching kinetics for copper minerals at these temperatures are rapid and acid is generated for potential use in heap leach operations. Pressure leaching of copper concentrates eliminates gaseous emissions of arsenic and sulphur, while generating environmentally stable residues, as measured by the Toxicity Characteristic Leach Procedure (TCLP) (Kalanchey et al., 2007). Both medium and high temperature pressure leaching of copper concentrates have also proven themselves technically on an industrial scale (Marsden et al., 2004) with high copper recoveries.

Jan 1, 2019

By M. Leroux, S. R. Rao, J. Kim, J. A. Finch

"Continuous in-plant testing of collectorless Cu/Pb bulk flotation on Lyon Lake ore at Matlabi Mines Ltd. Was conducted using a portable circuit based on 5 L mini flotation cells. It is concluded that collectorless Cu/Pb flotation is a reliable phenomenon for this ore over the usual range of plant operating conditions.IntroductionFlotation of some sulphide minerals without the use of conventional collectors (e.g. xanthates) is now widely recognized. The requirement appears to be some degree of oxidation, although the nature of the surface product formed is still uncertain (Luttrell and Yoon, 1984; Buckley and Walker, 1988). The phenomenon has been termed ""collectorless"" or ""self-induced"" flotation. One of the minerals most responsive to coUectorless flotation is chalcopyrite; in contrast pyrite and sphalerite show little response and galena usually shows intermediate response (Hayes et al., 1987; Shannon and Trahar, 1986).Most of the work on collector1ess l1otation has involved single mineral or batch flotation on ore samples. There are only occasional references to collector1ess l1otation under plant conditions (Sandstrom and Jonsson, 1988; Vargas, 1990; Boyce et al., 1970). Creating and maintaining the appropriate oxidation conditions and differences in water quality are among the reasons why the phenomenon may not transfer readily to the plant (Grano et al., 1990). Periodically from the spring of 1989, Mattabi Mines Ltd. ran full-scale tests of collector1ess bulk CulPb flotation while treating Lyon Lake ore*: the observations confirmed the laboratory finding that chalcopyrite and galena floated without collector (Leroux et al., 1989).To explore this finding continuous in-plant testing using mini flotation cells was conducted which is the subject of this paper. The main objective was to determine if collectorless flotation was a reliable phenomenon over the expected range of redox conditions in the feed pulp to bulk CulPb roughing. As background, the previous work (Leroux et al., 1989; Martin, 1988) is briefly reviewed."

Jan 1, 1994

By Emile D. L. Rienks

We have studied the interaction of NO with the quasi-hexagonally reconstructed Au(100) surface. Using variable temperature scanning tunneling microscopy we have observed formation of the unreconstructed phase of Au(100) after NO exposure. This NO adsorption induced phase transition is observed in a window of temperatures around 170 K. Under the same conditions, CO and O2 cannot drive the phase transition, suggesting weaker interaction. Thermal desorption spectroscopy experiments provide an estimate for the strength of NO chemisorption on Au(100) of 57 ± 4 kJ mol-1.

Oct 1, 2003

By T. M. Ahmed

Sherritt International Corporation experienced corrosion failures with the 316L stainless steel tubing in a high-pressure still condenser employed for ammonia recovery. A detailed failure analysis was conducted on the condenser tubing to determine the mode and the root cause of the failure. The analysis included both optical and scanning electron microscopy (SEM) of the inner and outer surfaces of the tube as well as characterization of the corrosion products using energy-dispersive X-ray spectroscopy (EDX). Results revealed that the corrosion attack was confined to the first ?100 mm of the tubing at the inlet where the tube was connected to the top tubesheet. The tube suffered both external stress-corrosion cracking (SCC) and crevice corrosion from the shell side (water side), and wall thinning of the inner surface (the tube side) due to erosion corrosion. It was evident that failure of one of the tubes occurred due to SCC that penetrated the whole wall thickness and resulted in a leak failure. Some prevention measures are proposed to avoid this type of corrosion attack in the future.

Jan 1, 2005

By J. Schmidt

Cold drawing of copper wire rod is usually combined with an in-line annealing process to adjust the ductile microstructure of the wire again. One important key factor for successful annealing is the quality of the copper itself. Rod producers can check the recrystallization behaviour of the rod by different methods: chemical analysis, Spiral Elongation Test (SEN) as well as the Rapid Elongation Test (AR) are some examples of common testing methods. The comparison of the results of these methods does not always show sufficient correlations. The paper introduces firstly the SEN and AR-Tests and their different approaches to the mentioned task. The second step is to compare some results of the SEN-Test with the results of the AR-Test and identify causes of deviations. Thirdly, the effect of pre-annealing is discussed, which is especially common for wire rod with diameters of more than 8 mm.

Jan 1, 2007

By M. H. Moys, C. Bhondayi, Eric Tshibwabwa

"The relationship between froth bubble size as represented by intra-bubble impact distances (IID) and flotation performance is investigated. Experiments using an artificial ore comprising of limestone as the floatable component and silica as the gangue material were carried out in pseudo-steady-state circuit. A method to measure IIDs developed by Bhondayi and Moys (2014) was then used to measure froth bubble sizes as a function of froth height, superficial gas velocity and feed rate (pulp residence time). Samples for flotation performance evaluation were also taken. Results indicate that as froth height increases, the average IID values increase resulting in a decrease in limestone recovery while the grade increases. Increasing gas rate results in lower IID values that are accompanied by high recovery and low limestone grade. The effect of feed rate on both flotation performance and average IID values depended on froth depth and gas rate. Average IIDs largely remained the same at the two feed rates investigated.INTRODUCTIONIt is regarded as obvious that froth bubble size distribution (FBSD) will have an effect on plant grade and recovery. As the average FBSD decreases, the bubble surface area flux will increase making possible an increase in recovery and a decrease in grade. The opposite trend will be involved if average FBSD is increased. However: no method for measuring FBSD has been available, so these trends have not been studied in any detail. Bhondayi and Moys (2014) developed a novel technique to measure or estimate froth bubble sizes. Although they established a potential to use this method in understanding froth performance, no data have been presented to assess the correlation between the estimates of bubble sizes and actual flotation performance. In this work experiments are done to establish how the change in froth phase bubble sizes affect flotation performance. Flotation performance will be evaluated using recovery and grade. How water recovery to the concentrate changes with changes in bubble sizes will also be evaluated. It is known that water recovery is approximately inversely proportional to the square of the overflowing bubbles sizes. It will be interesting to establish how the rate of change of bubble sizes changes with water recovery."

Jan 1, 2016

By R. K. Sidhu, N. L. Richards, M. C. Chaturvedi

Nickel base superalloy IN-738LC, strengthened mainly by the precipitation of y' phase, is extensively used in hot sections of land-based and aero gas turbine engines. Fusion welding, which is one of the most commonly used joining techniques for the repair and fabrication of superalloy components, however, finds a very limited application in case of IN-738LC components, as the alloy suffers from HAZ cracking during welding and during subsequent postweld heat treatment (PWHT). The present paper reports on the two methods studied to reduce the HAZ cracking in as-welded and postweld heat treated GTA welded IN-738LC, viz., the use of various fillers during welding, and the use of appropriate heat treatments prior to welding. The results of the microstructural analysis and crack measurements indicated that the HAZ cracking in GTA welds of IN-738LC was significantly reduced by using age-hardenable fillers with Al+Ti concentration less than that in the base metal in conjunction with a preweld heat treatment developed by the authors.

Jan 1, 2006

By Kosei Ishida

To achieve renovation work without noise, the authors developed techniques of manufacturing pre-cut interior finishing components for renovation work. In this paper, to achieve the system of pre-cut interior finishing components, the authors describe a measuring method of reinforced-concrete structure by 3D laser scanner and then describe a method of making a design of pre-cut interior finishing components with the polygon model. Using these two methods, the steps of manufacturing pre-cut interior finishing components consist of the following four steps: First, measure the building shape using a 3D laser scanner. Secondly, integrate a point cloud data and retrieve the markings on the floor. Then, create a polygon model of the building based on the point cloud data. Lastly, make a drywall design using a polygon model. To evaluate the technique feasibility of manufacturing pre-cut interior finishing components, the authors have conducted an experiment of the finishing interior work of the drywall. Using pre-cut interior finishing components, the authors have been able to achieve interior finishing work without noise.

Aug 1, 2013

By D. Lemieux

A gold bearing pyrite concentrate was treated at the pilot scale for the extraction of gold. Mineralogical analysis of the concentrate identified gold to be mainly present in the form of a solid solution in pyrite. This gold distribution resulted in a poor extraction yield of 55% by direct cyanidation. A piloting campaign including an oxidative pre-treatment by roasting in a fluid bed was followed by treatment with halogens for gold extraction has led to a gold extraction yield of 96.5%. Sulphur removal during the oxidation was very efficient at >99.5% and gold extraction by the halogens was completed within a 1 hour contact time. The piloting was performed on a 300 kg sample and uses a diluted solution of hypohalites as the oxidizing agent for gold extraction. Sulphuric acid was injected in the reactor during the halogens treatment to lower pH to 2. The diluted solution of hypohalites (1-3%) was generated by electrolysis during the piloting campaign in a membrane-less electrolysis cell. The extracted gold was recovered over activated carbon in column and the gold depleted brine was treated for impurities removal and recycled for further gold extraction. With the recycling of water and brine, the regeneration of hypohalites and with a barren solid that is inert and stable, the Nichromet Extraction technology is a green process where the protection of the environment does not preclude profitability.

Aug 1, 2013

By J. Boulton

"Nuclear energy is an established and proven energy source. Today, CANDU-PHW nuclear-electric generating stations produce over one third of Ontario's total electrical supply: safely and economically. In many parts of Canada, where economic hydro resources do not exist or are fully developed, coal and nuclear energy are the only alternatives for future large-scale electrical generating capacity.Recent analyses have suggested that, in the f ace of increasing energy demands and decreasing reserves of hydrocarbon fuels, Canada must depend on electricity to provide an expanded fraction of its energy budget. Nuclear energy is likely to play an increasing role in the generation of electricity; there are also potential applications as a supplier of process heat in industry and in the in-situ recovery of bitumen fro m tar sands.The future supply of nuclear fuel, reactor safety and radioactive waste management are briefly discussed. In each case, the benefits to be gained from a controlled expansion in the use of nuclear energy outweigh any uncertainties which may exist."

Jan 1, 1981

By P. R. A. Andrews

"Areas of bubble contact were delineated for cassiterite in the presence of chloride, fluoride, sulphate, phosphate, oxalate and citrate ions using dodecylamine hydrochloride collector. The limits of pH, and the minimum collector concentration were established using the bubble pick-up technique.Bubble contact did not occur below the p.z.c. (point of zero charge), estimated to be 4.7, in the presence of chloride ion, and fluoride ion showed only a weak response in the same pH range. These anions are considered to act as indifferent electrolytes. Activation at pH values below the p.z.c. was obtained with sulphate, phosphate, oxalate and citrate ions; the greatest response was by oxalate and phosphate ions extending pick-up to between pH 2.0 and 2.5.Activation appeared to be strongest when anionic protonated species were in maximum concentration. Strong activation also corresponded to the formation of very stable metal ion species, thought to be formed on the surface of cassiterite, between exposed stannic ions and modifying anions; dodecylammonium ions being absorbed on the surface so modified."

Jan 1, 1991

By A. J. Williams, W. H. A. Timm

"Lake Dufault Mines, Limited, is located north of Noranda, Quebec, and is a producer of copper and zinc concentrates. Various papers have been given on the mill design, construction and operation. 1, 2This paper is intended to describe the application of computer control to the Lake Dufault milling process. A brief history and description of the plant flowsheet will be given, followed by the reasons for installing the computer and the development of the program up to its present use. The success attained to date, comments on economic justification and future plans will also be given.HISTORY AND FLOWSHEETThe Lake Dufault ore body was discovered in September, 1961, and the mill commenced production during August, 1964. The rated capacity of 1,300 tons per day was reached by October 1, 1964. In milling the Lake Dufault ore, many metallurgical problems have been encountered, mainly due to wide and rapid variations in mill heads and oxidation of the massive sulphide ore. However, flexibility in plant layout and the incorporation of up-to-date instrumentation have facilitated its processing."

Jan 1, 1969

By Jianglan Duan, Steve L. Cockcroft, Andre B. Phillion, Carl Reilly, Daan M. Maijer

"In the aluminum alloy wheel casting process, careful design of the cooling system in the die and its operation (cooling channel timing) are critical to achieve quality and productivity goals. The problem is challenging owing to the cyclic nature of the process and the relatively large thermal mass of the die in comparison to the wheel. For a given die geometry, a set of constraints have been defined to ensure directional solidification and an objective function, based on cooling rate during solidification, has been defined to reach a target secondary dendrite arm spacing. The methodology presented in this study employs the commercial finite element package, ABAQUSTM, and an optimization module based on the open source library, Scipy. The developed methodology has been applied to a series of geometries and cooling system configurations, including a 2-D axisymmetric wheel and die assembly generated from a prototype die. Preliminary testing has shown that careful selection of the objective and constraint functions have made it possible to reach desired solidification pattern.TM- Dassault Systèmes Corp."

Jan 1, 2014

By R. F. Engler

"IntroductionThe Coal Branch region of west-central Alberta has been the focal point for unprecedented exploration and development activities over the past ten years prompted by the renewed markets for high-quality thermal coal. Although mines were developed and operated extensively throughout the region from 1910 until 1960, information relating to the detailed stratigraphy of the coal measures and their areal distribution tended to be localized to individual mine sites. Continuity along trend was impaired by a paucity of outcrop restricting geologic mapping to stream bank and roadside exposures. Recent studies and subsequent publications by Jerzykiewicz and McLean of the Geological Survey of Canada (1978, 1980) have established a detailed sedimentological model and defined the stratigraphic nomenclature for the region . The term Coalspur Beds has been adopted to describe the coal-bearing sequence between the overlying Paskapoo Formation and underlying Brazeau Formation. Complete sections of the Coalspur Beds have been compiled from sub-surface borehole data and published by Manalta Coal Ltd ., Dentherm Resources Ltd. and Luscar Stereo Ltd. This paper is an attempt to correlate this information on a regional basis to illustrate trends within the Coalspur Beds."

Jan 1, 1986

By K. G. Eriksson

"The first tentative test made to try rubber lining in grinding mills was made in the early twenties. However, because of poor rubber compounds and design the results did not prove to be promising.In the early sixties successful trials of rubber linings were carried out as a result of a cooperation between boliden AB and Skega AB.One of the reasons rubber was not used earlier for linings was the difference in wear characteristics between rubber and steel. The ability to successfully develop rubber mill liners depends on three factors:l. Design2. Material (rubber compounding)3. Experience (knowledge)DESIGNThe main difference between steel and rubber, in material aspect, is the elasticity and the low tensile and shearing strength of rubber. It is necessary to take maximum advantage of the elasticity and to reduce tensile and shearing forces by minimizing the sliding of the mill charge. This is accomplished by using the Lorrain type of liners, i.e., lifter bars and plates. It is, however, necessary to keep a certain balance between lifter bars to optimize liner life and grinding performance."

Jan 1, 1983

"Chairman - To start this discussion off, I wonder if Mr. Dave Livingstone or Mr. Jeffrey of Granisle Copper would give a description of the crushing plant at Granisle since it is somewhat different from the usual plant, W. N. Jeffrey - Granisle Copper The main difference between the Granisle crushing plant and many others is the Livingstone method of putting the screens under the crushers instead of above them. This method allows a more compact arrangement and eliminates the heavy superstructure required to take care of the screen vibration when the screens are mounted above the crushers. There is a small surge bin above the tertiary crusher which takes care of the variation in circulating loads.All three crushers are gyratory crushers. There is no grizzly ahead of the primary crusher but the fines are removed from the primary crusher discharge at the first screen and sent directly to the fine ore bins. E, Thornton - Sullivan GroupDo you have any coarse ore storage outside?w. N. Jeffrey - Yes, there is about 6000 tons live storage, We have very little trouble with freezing even though it is open storage.E. Thornton - Sullivan GroupDoes rain cause any problem?w. N. Jeffrey - It sometime creates a problem because the storage area is on a slope. It is mainly a problem of keeping the drainage ditches open.Question – What is the size of the primary gyratory crusher and how does it work on run of mine size materials, in other words, do you have a problem with oversize material and how do you handle the oversize rock?w. N. Jeffrey - The primary gyratory is a 42 x 65 with a nominal open side setting of 61'. We do at times get a run of oversize material. For anything too large for the crusher to handle, we use what is known as the Esco hook, which is a type of grapple used to remove oversize rocks.The disadvantage with this equipment is that the crane is too slow. I am sure there must be better arrangements than the one we have,"

Jan 1, 1971