Search Documents

By R. Farhat

Coating systems that yield a thermally grown oxide (TGO) protective layer have been proposed as a potential method for extending the lifecycle of components exposed to high temperature corrosion. This is particularly relevant to the petrochemical industry, where any reduction in corrosion rates can yield substantial cost reductions. The primary goal of this project is to develop a coating repair procedure and to investigate the oxidation performance of the repaired location. Electrospark deposition (ESD) was used to repair spalled segments of TGO grown on MCrA1Y substrates using various electrodes possessing mixed crystal structures. Specifically, electrodes of NiCoCrA1Y (BCC-FCC mixtures) and CoNiCrA1Y (FCCBCC mixtures), were deposited and oxidized to develop the TGO using a heat treatment of 24 hours at 1000°C in air. This presentation will focus on the microstructural evolution of the base metal and ESD repair on damaged area, in both as- deposited and oxidized forms. Results of SEM and XRD analysis will be presented.

Jan 1, 2011

By Sina Mostaghel, M. Guo, E. Klaffenbach

The current paper is focused on evaluating the behavior of copper in a copper production slag and the assessment of metal recovery possibilities. For this reason, thermodynamic calculations were carried out to determine the influence of parameters such as slag composition, temperature and oxygen partial pressure on recovery of non-ferrous elements. It was found that the formation of a solid face centered cubic (fcc) phase, mainly consisting of iron, limits the extent of reduction that can be achieved for an industrial process. However, it could be discovered that solubility of iron in the Cu-rich liquid alloy strongly depends on presence of other elements, particularly arsenic. As part of the results of this study, the solubility of Cu in the slag at onset of fcc phase formation is presented as function of temperature, oxygen partial pressure and concentration of MgO and CaO. It was concluded that lower temperature (1200°C) and higher CaO addition (16 mass-% in this study), would result in the highest achievable copper recovery from slag. INTRODUCTION Copper slag is produced as a by-product of the copper production process. The slag is still containing a high amount of copper and other valuable metals. This demands further treatment of the slag as a secondary source of metals. In addition, the physical/mechanical properties of slag allow its use in several applications such as hydraulic engineering, civil engineering, as an abrasive and many more. These applications help reducing the use of natural resources like rock and sand. By decreasing the content of heavy metals such as Cu, Pb, Zn and As in the slag, its application in abovementioned fields becomes more attractive as the probability of releasing these elements to the environment is further reduced. To develop a pyrometallurgical slag reduction process, it is necessary to understand what describes the end point of the reduction. This point is expected at maximum copper recovery without facing operational challenges. Existing literature provide some information on the effect of different parameters such as temperature or concentration of different slag formers, on solubility of copper and heavy metals in different phases. However, due to complexity of industrial slags, equilibrium experiments and accurate thermodynamic modelling are essential to be able to reliably predict the behavior of different elements in the system and determine the end-point of reduction.

Jan 1, 2019

By Tong Gao, Jingyu Qin, Xiangfa Liu, Zengqiang Li, Yaoxian Zhang

"The recycling of aluminum materials is a green industry while Al–Si–Fe is a typical scrap aluminum alloy. The key point of recycling Al–Si–Fe alloys is to separate Al and Fe. A method by introducing Al–Si–Fe alloy into Mg melt has been investigated in this work. A separation layer with gathered Fe–rich and Al–poor Fe3Al0.7Si0.3particleswereobtained at the bottom of the cooled ingot, indicating that ß–Al5FeSi phase evolves to Fe3Al0.7Si0.3,and quantities of Al are released to the upper Mg matrix simultaneously. However, the evolution of Al3Fe by adding binary Al–Fe alloy into Mg melt is different. It is supposed that element Si plays an important role in the phase evolution procedure, thus affects the performance of this method.INTRODUCTIONThe rapid development of aeronautic, automotive and aerospace technologies strongly depends on the consumption of materials while sustainable development is the future direction. Aluminum is a recyclable material and Fe is one of the most common impurities. Fe can be introduced into Al alloys by adding low–purity alloying materials and by using unprotected ferrous crucible, tools, or equipment (Belov, Eskin, & Avxentieva, 2005; Lu& Dahle, 2005).For instance, wear–resistant rings are usually inserted into piston head when producing Al–Si pistons and an infiltration procedure by putting the cast iron rings into Al melt before casting is always essential. As a result, both the re–melting of pistons and the reuse of Al melt for infiltrating rings lead to the enrichment of Fe element, which can be even high to5 wt.%(Viala, Peronnet, Barbeau, Bosselet, & Bouix, 2002).It is widely known that coarse ß–Al5FeSi particles will form in high Fe–contained Al–Si–Fe alloys which is harmful for the mechanical properties. In the past decades, several methods to eliminate the harmful effect of ß–Al5FeSi have been investigated which can be widely referred (Munson, 1967; Lee, Kawamura, Inoue, Cho, & Masumoto, 1997; Suárez–Peña& Asensio–Lozano, 2006; Eidhed, 2008).These methods can be divided into two kinds. One is to aggregate and remove the Fe–rich phase through the methods of centrifugation, gravity filtration or magnetic separation. The other way is modifing the morphology of flake–like ß–Al5FeSi by overheating the melt or adding neutralized elements. However, these traditional methods are rarely used due to respective disadvantages, while the commonly used method in industries is using primary aluminum for dilution. However, only less than 30wt.% of scrap Al can be added into primary Al melt for each melting work while it also results in the decrease of product quality simultaneously(Zhang, Liu, & Liu, 2016)."

Jan 1, 2018

By D. R. Winchester

"I wish to thank you and your organizers for inviting me to address you at this point in time when we are all concerned for the future of the mineral industry in Canada.My topic ""Some Initiatives of Government Assistance to Industry Applicable to Mineral Processing"" is purposely limited in scope. To cover the entire range of initiatives in detail would take me all day, and at best, would be a mere recital of program titles, and a one sentence summary of the contents of the program. As you know, OREE or Regional Economic Expansion, is in the process of being amalgamated with elements of the Department of Industry, Trade and Commerce. We will become Regional Industrial Expansion or ORIE. If the name Canada Dry becomes popular, I don't think we will object as we hope to become a good mixer. The entire departmental thrust has been re-evaluated, and is in the process of being re-constituted to better serve the nation, and industry as a whole. Amalgamation of the industrial, trade promotion and marketing support skills of IT&C, with the regional development orientation and decentralization program delivery mechanisms of DREE, will, it is believed, provide better support to industry on a national and regional basis."

Jan 1, 1983

By M. Gruber-Pretzler

Technical Sn- bronzes tend to form both macrosegregations and microsegrega¬tions during DC-casting due to the particular thermodynamic properties and kinetics of phase transformation. As a result a heterogeneous cast microstructure forms that is some¬times a reason for a decrease in workability. The extent of macrosegregations in DC-casting can effectively be influenced by casting parameters like casting velocity, primary cooling or inlet geometry which in fact change the relative flow between the melt and the forming solid. In order to understand the influence and interaction of the related phenom¬ena, simulation methods are applied. The solidification of the strand as well as the forma¬tion of macrosegregation are simulated with a two phase volume averaging model. The velocity field of the melt flow is explicitly calculated by solving the corresponding mo¬mentum conservation equations. Within the mushy zone the local formation of microseg¬regations in the presence of feeding flow is estimated. The thermodynamics of the Cu-Sn system is accounted for and it is distinguished explicitly between interface and average concentrations. To investigate the influence of feeding flow on the formation of mac-rosegregations, a study has been performed. Based on this result, the phenomena of mac¬rosegregations are described in a detailed discussion.

Jan 1, 2007

By Mario A. Morin

Over the years, several sources have stressed the need to better integrate the underground mine design and planning processes. The belief is that with better integration, better designs and plans will result - designs that are ?optimized?. Some researchers have focused their efforts on data integration, others have looked at closing the loop between production control & monitoring with mine planning & scheduling. In spite of all these efforts, fully integrated applications combining geological modeling, stope design and geomechanics, mine planning and scheduling, rock extraction and material handling system design, mine support systems, economic analysis with production control do not yet exist for the underground hard rock mining industry. There are several likely explanations - some economic, some technical. It is certain that the design and planning processes are interrelated and interdependent and thus are extremely complex to describe and understand. The mining engineer has an appreciation of the complexities involved - but how does he convey this knowledge to a programming team responsible for developing an integrated design & planning system. This paper will focus on software engineering methods, and other possible approaches, to describe and manage the complexities inherent in the underground mine design and planning process and the development of an integrated computerized system.

May 1, 2001

By Jeffrey D. Smith, William G. Fahrenholtz, Jose M. Soto

Interactions between A356 aluminum (Al-Si alloy) and dense fused silica (FS) riser tubes used for low-pressure casting of aluminum alloys were evaluated using a sessile drop approach. The tubes have a short service life, but cost and thermal shock resistance make them an effective solution. The main problem encountered during use is the reaction of aluminum with silica to form alumina and silicon, which causes failure. Tests have been conducted on as-fired (uncoated) and modified (coated) tubes. Experiments were carried out in a horizontal furnace at 1225°C under argon to minimize the effect of the aluminum oxide on the interactions at the alloy-silica interface. Images of the drop were acquired and contact angle values were estimated for uncoated and coated samples, but no significant differences in the contact angles were observed. Scanning electron microscopy revealed the presence of cracks at the interface between the reaction zone and the unreacted silica. The presence of reaction products (silicon in the reacting alloy and aluminum in a reaction zone between the alloy and the unaffected silica) has been confirmed using energy dispersive spectroscopy. A two layer coating system was found to be effective in reducing penetration of the aluminum alloy.

Jan 1, 2004

By P. Au, R. Kearsey, D. Y. Seo, Patnaik. P. C.

Three nickel based superalloys (7.5%Cr+5%Co+2%Mo+1%Ti+5%Al and Ni balance (wt%)) containing different amounts of W and Re were produced in the single crystal (SX) condition utilizing the Bridgman casting process. First, the effect of different levels of Re, and W on chemical microsegregation were investigated by EPMA quantitative analysis, and eutectic phase fraction analysis. Second, in order to investigate the effect of these refractory elements addition on oxidation behaviour, isothermal oxidation testing of the SX nickel based superalloys was conducted at 1000°C for 277 hours under 3 ppm moisture content of air in a thermogravimetric analyzer (TGA). All three SX nickel based superalloys revealed an excellent SX solidification structure with a common primary dendrite arm spacing of -250 µm and a large fraction of ?/?' eutectic located between the secondary dendrite arms. From the average EPMA compositional results, with the exception of Ni, elements such as Cr, Co, Re, Mo, and W all tended to segregate towards the dendrite core during solidification, while Al, Ti, and Ta were present in greater quantity in the last liquid phase to solidify, which resulted in large eutectic ?/? ' phases to form within the interdendritic regions. As the nominal level of Re increased, microsegreagation of Re, W, Cr and Mo increased, indicating that Re had a much greater influence on partitioning behavior compared to W. Figure la shows the specific mass gain as a function of exposure time for each alloy. An alloy with 2wt% of W and Re (Alloy B) exhibited less weight gain compared to two other alloys with either higher content of W or Re (Alloy A and C). Microstructural and compositional analyses of oxidized samples were conducted using SEM and EDS. Figure lb shows the typical surface morphologies of the oxidized Alloys A and B. It is evident that more oxide nodules (indicated by arrows in the figure) were presented in Alloy A. It is speculated that the amount of these nodules was responsible for more mass gain in Alloy A compared to the two other alloys. From the examination of the longitudinal section of the oxidized samples as shown in Figure 2, for Alloy A, nodules actually penetrated deep into the material. For Alloy B, however, a relatively uniform and continuous oxide layer was developed and deeply attacked areas were not observed. It was also found that preferential oxidized regions were located at the area between the ?/?' eutectic phase and the dendrite arms where the concentration of refractory elements was relatively high. Therefore, it is plausible that the oxidation kinetics of these alloys is related to the extent of microsegregation.

Jan 1, 2004

By Robert B. Parsons

"The customary onslaught of government budgets this spring offers lots of interesting reading to the mining industry.While the favourable changes tend to get all the fanfare, there are some ""sleepers"" in the host of proposed changes which will be bitter pills for some mining people to swallow.IntroductionOn a scale of one to ten, the Canadian mining industry will probably give this year's federal and provincial budgets a score that is pretty close to five. Although some budgetary proposals are generally perceived to be favourable to the industry, there are other provisions (and lack of provisions) which are considered to be negative.This month, Tax Notes examines in a summary manner the principal features of the 1985 federal and provincial budgets which are of particular interest to this country's mineral industry."

Jan 1, 1985

By M J. Daniel

Comminution is the science of size reduction of brittle materials. It is integral to mineral extraction and is one of the most energy intensive processes in the mining industry. There are a number of tests used to quantify the strength of ore, which are then used to size the AG / SAG mill in circuit design. The calculated energy utilized for breakage in these devices is based on the assumptions that the materials treated are of average shape and that the processing equipment is designed to break the ore as efficiently as possible under the given operating conditions. In drop weight tests, it was found that shape significantly influences the measured rock strength. Controlled experiments with variations in blends of rock shape show that mill throughput increases with the addition of weaker shaped rocks.

Jan 1, 2012

By Randolph A. Pax

"The internal operation of a tumbling mill is a very hostile environment and precludes the sustainable operation of internal sensors to measure the mechanisms of charge motion and breakage events. Instead indirect methodologies are required to expand the current understanding developed within a framework of perfect mixing of the mill contents. A number of measurement approaches have been successfully used to explore the operation of SAG mills including strain instrumented lifter bolts, mill shell strain measurement and thermal (energy balance) of operating mills.Early acoustics measurement was developed by Hardinge using a 'microphone' located close to the expected toe location. This signal was an indicator of the mill fill. Improvements were implemented with the use of two microphones straddling the toe location to try to increase the sensitivity of the measurement and reduce ambiguities. Further improvements included a filtered signal indicative of steel interactions. Unfortunately, the mechanisms of signal generation and the complexity of the processes do not provide a consistent signal.In recent years, advanced acoustic measurement using arrays of microphones utilising signal processing techniques have been implemented as SmartNoise and validated on over 30 mills. This paper will discuss the results obtained with signals such as water holdup, mill shell steel hits and two each of the toe and shoulder angles. An estimate of the internal mill component wear rates is also accessible.Advanced acoustic measurements with wide bandwidths when combined with physics models and process understanding has achieved a step change in the understanding of the dynamic internal operation of a tumbling mills on time scales of 80 ms. These techniques have been used extensively on SAG mills, but have also been applied to FAG and ball mills. Acoustic measurement is used for the rapid diagnosis of mill conditions and holistic control for optimisation and stability."

Jan 1, 2016

By C. Caners

One of the main uses of fossil fuels is in the transportation sector, leading to environmental consequences such as climate change. In order to move towards a more sustainable energy infrastructure, a transition must begin from fossil fuels to renewable fuels, derived from e.g. biomass. One means of facilitating this transition is to develop reforming technology that can extract hydrogen from a suitable fuel that is either fossil fuel or renewable in origin. The hydrogen would be feed to a 'fuel cell' engine that would power the car, truck or bus. One reforming technology that is attractive for automotive applications is autothermal reforming (ATR). Autothermal reforming is the combination of steam reforming and partial oxidation, whereby a portion of the fuel is combusted using a sub-stoichiometric amount of air, and the resulting thermal energy drives the more desirable steam reforming reaction. ATR is attractive for fast start-up, rapid load following and ease of control. ATR also has the benefit of smaller volume and fewer peripheral requirements as compared to other reforming technologies. Recently, a bench-scale gasoline autothermal reformer (ATR) was constructed and tested. This ATR employs a novel design, consisting of three concentric annuli in order to promote heat transfer from the partial oxidation reaction to the steam reforming reaction. Concurrently, a CFD based model (FLUENT) of the ATR that considers the geometric complexity of the reformer was validated. In spite of the use of simplified kinetics, the model predicted well the observed trends in temperature and overall performance. This paper will discuss the use of the model to improve the design of the ATR. The impact of various system parameters upon performance will be investigated along with alterations in the geometry of the ATR. The various tradeoffs in performance and system volume/size will be highlighted in the context of a fuel cell power system.

Jan 1, 2005

By Deni Lessard, Roger Demers, Noël R. Billette

"The Quebec Mining Association has for many years been supportive of the activities of the Centre de recherches minérales which were initiated to ensure regular production hoist and cable inspections to maintain safety and productivity standards in underground mines in Quebec. CRM and CANMET have agreed to fund a Quebec Mineral Development Agreement contract to capture this accumulated knowledge. Using VP-EXPERT to process the information and subdirectories to store regulations, the prototype access D-BASE III records on hoist information and LOTUS 123for simulating working conditions that meet local regulations and expert rules of thumb criteria. Objectives are to improve safety in emergency operating procedures, maximize hoist productivity and safety, and promote knowledge transfer to operators."

Jan 1, 1992

By F. Mallozzi

"With the requirements of air pollution codes becoming more and more critical, the role of the ventilation engineer in industry has become an extremely important one. The ventilation engineer must provide the expertise for the selection of equipment and the design of systems which will reduce pollution to an acceptable level. Because pollution control systems involve considerable capital and operating expense, he must have the ability to select, from a wide range of products, the collector which will provide the required performance with a minimum of down time for maintenance. This paper discusses the principles of wet collection and the forces used to separate particulate matter from a gas stream. Important factors in the selection of equipment, such as collection efficiency, horsepower requirements and water consumption for the various types of collectors, are discussed in detail, as well as the construction features normally incorporated to circumvent potential problems."

Jan 1, 1971

By P Kovacs, D. L. Flock

For the purpose of reservoir-performance calculations a balance can be made between the materials with-in the reservoir and the production from the reservoir. The material balance equation, a relationship which holds under or near equilibrium conditions, has been used in many forms by the Petroleum Engineer for the determination of initial oil-in-place in the reservoir and the calculation of performance into the future. One of the more recent methods developed by Tracy, utilizes a modified form of the Schilthuis material balance. In the latter case, values of incremental production are assumed for a particular pressure drop, a value of the gas-oil ratio found and a check of this estimate made by calculation"' the initial oil-in-place. Tracy's method utilizes an estimation of the instantaneous gas-oil ratio and by trial and error a value of the gas-oil ratio is

Jan 1, 1961

By L. D. Smith

"Those who submit competing proposals for projects seek to present senior management with complete and fully supported material that will not fail under questioning. Hopefully, misleading notions and omissions will have been minimized and there will have been testing of the assumptions regarding the economic, social and political environments.A capital project evaluation team can do management and itself a service by including a sound approach to the impact of inflation (and its twin problem, interest) on a project and a great disservice with an inappropriate approach to inflation.InflationHandled deftly, inflation can alter a project evaluation to show almost any result the handler desires. It must be a constant source of frustration for design people and cost estimators to spend weeks perfecting the technical aspects of a project in order to minimize costs, only to have all of their efforts set awash in a sea of financial and economic assumptions that submerge all of the detail. In all of this, inflation is perhaps the largest offender, with inflation criteria often being brought to bear at the last minute, almost as an afterthought. Perhaps this tardiness reflects the difficulty of the subject and the belief that senior management will take its own approach to the problems of inflation. Such a belief is unfair to senior management, for it is entitled to not being misled by omission. It is entitled to the full use of the skills of the evaluating team, including reasonable assumptions of the impact of inflation.Working in a consulting context, one has the opportunity to participate in the evaluation of a large number of projects."

Jan 1, 1990

"Batch flotation testwork demonstrated that a low-grade chromite ore from Bird River, Manitoba, was best floated at pH 2 using Armac C (coco amine acetate) collector and sulphuric acid as pH modifier. A grind of 100% minus 150 um was necessary for liberation, and flotation selectivity was greatly enhanced by prior desliming. A concentrate analyzing 24.2% Cr203 with a recovery of 90.2% was obtained, after three cleaning stages, from ore grading 6.05% Cr203. Total rougher collector concentration was 500 g/t and cleaner collector concentration 380 g/t. Similar grade and recovery were obtained during the pitot-plant evalualion, when a concentrate analy zing 22.3% Cr203 with a recovery of 93% (based on deslimed feed) was obtained for a total collector addition of 630 g/t.Selective flotation in a region of positive surf ace charge implies anionic activation, and a possible flotation mechanism is suggested.IntroductionIn an earlier study(1) of the beneficiation of chromite ore from Bird River, Manitoba, several methods of beneficiation were explored. These included ore sorting, heavy-media separation, and gravity concentration with flotation using Armac C (coco amine acetate) collector at pH 2, and sulphuric acid as pH modifier. Because flotation was not fully evaluated, a laboratory study was undertaken to determine the optimum parameters of chromite flotation. Optimization of parameters was established first on a laboratory scale followed by confirmation a t the pilot -plant level. Flotation of chromite using Armac C and sulphuric acid as a pH modifier has been reported as being selective for low-grade chromite ores(2)."

Jan 1, 1990

By Peter Godbehere, Christian Desroches, Viken Baboudjian

"Noranda Copper Smelting and Refining is a unit of Noranda Metallurgy Inc., comprising the Home smelter in Rouyn-Noranda, Quebec and the C.C.R. Refinery in Montreal East. The Home smelter provides custom smelting services for a wide variety of copper and precious metal bearing concentrates and recyclable materials, producing over 200 000 tonnes of anodes and 450 000 tonnes of sulphuric acid annually. The C.C.R. Refinery has an annual production of 360 000 tonnes of copper cathode, and is a major refiner of precious metals.Over the past twenty years, Noranda Copper has developed innovative processes and operating techniques to treat the ever increasing complexity of primary feed materials, while improving the quality of its final products, working conditions and reducing environmental emissions.This paper presents an overview of the operating practices of Noranda Copper with particular emphasis on the impact of impurities in the smelting and refining processes.IntroductionThe treatment of custom materials has been practiced by Noranda Copper since commencement of operations at the Home smelter in 1927 and the CCR refinery in 1931. Copper concentrates from a wide variety of regional, North American and overseas producers account for the bulk of the 800 000 tonnes treated annually, although recyclable and secondaries have increased in importance as feed sources in the past two decades. The geographical disadvantage of the Horne smelter compared with most custom smelters located on tidewater has provided an important incentive for Noranda Copper to develop the necessary technology and operating practices at its smelter and refinery to treat high value complex concentrates and other feeds containing significant concentrations of bismuth, antimony, arsenic, lead, tellurium, mercury, etc."

Jan 1, 1995

By Robert B. Parsons

"It is generally felt that flow-through shares face a bleak future under the set of tax rules proposed in the federal government's tax reform white paper. Industry and government circles are beginning to give thought to alternatives to flow through as a mechanism for facilitating equity financing in the exploration industry. Despite suggestions that grants and tax credits may someday be on the table, industry is sticking to its position that there is no substitute for flow-through. Alternatives toFlow-throughProposals in the federal government's tax reform white paper have cast significant doubt on the ability of the mining industry to raise risk capital after 1989by way of flow-through shares. There is serious concern that introduction of the ""cumulative net investment loss"" (CNIL) rules, the phase-out of the mining explorati0! 1 depletion allowance (MEDA), and the Increased capital gains inclusion (750/0 versus 50%, at present) will make the economics of flow-through so unattractive after 1989 that these shares will hold little appeal to most investors. The question might be raised, then, as to what alternatives exist by way of tax or other government assistance that could help the exploration sector.The purpose of this paper is to survey the types of government incentives that could be of some value to explorationists and to the mining industry in general. For the past several years, flow-through has been in the spotlight insofar as incentives to the exploration industry are concerned. Other potentially useful and attractive incentives have been partially hidden in the shadow of flow-through. These incentives, in certain circumstances, can be of considerable benefit, and should not be ignored."

Jan 1, 1988

By H. R. Wilson

"This paper describes the evolution of the Waste Management Program at the Lupin Mine through the years 1982 - 1988. The program was developed in response to the terms and conditions of the Water Licence issued to the mine in 1981 by the Northwest Territories Water Board. Echo Bay Mines Lupin Mine is located on the western shore of Contwoyto Lake in Canada's Northwest Territories about 80 km. south of the Arctic Circle.The gold mine commenced production in 1982 and the Waste Management Program was based originally on the total containment concept. Due to an expansion of the mill circuitry and increased throughput, it was apparent that the total containment concept would require reevaluation since discharge from the pond would be required within a few years. During the initial years of production, an investigative program was established to determine the most effective means for treating the tailings pond water. This program incorporated both laboratory studies as well as monitoring of the tailings pond contents and environmental conditions as the impoundment area was filling. The program showed that natural degradation phenomena, if properly utilized, are effective in lowering the concentrations of all contaminants to within Licence limits with the exception of arsenic. To ensure compliance with arsenic limits, an iron salt was added to cause arsenic to precipitate from solution in the tailings pond.As a result of our studies, the tailings management system finally implemented at Lupin Mine includes the following components:Tailings pulp retention cells constructed by dyking off one end of the tailings impoundment area.Two tailings ponds in series operated in a sequential decant and fill fashion.An iron salt solution preparation and metering system.A syphon system into which the iron salt solution is injected as the contents of the first pond are decanted into the second pond.A second syphon system for decanting the contents of the second pond to the receiving streamThis paper discusses the findings and conclusions of the waste management investigative program, describes the civil work completed to reach our final operating scenario, describes the sequence of operating the treatment system, reviews performance data, and comments on abandonment and restoration of the tailings impoundment area."

Jan 1, 1989