Search Documents

By B. McFadzean, I. Achaye, T. Chidzanira, J. Wiese

"Froth stability has an overriding effect on metallurgical recovery and grade for many ore types. Froth recoveries of less than 10% are common for low stability froths such as those in sparsely mineralized ores or in cells at the back end of flotation circuits. It is well known that, aside from chemical factors such as frothers and electrolytes, the mineral particles themselves have the dominant influence on froth stability. The particle properties of size and hydrophobicity are expected to have the greatest effects on froth stability. The aim of this study was to understand the effects of particle size on froth stability and to quantify these relationships.The study compared a synthetic ore of pyrite and quartz, with carefully controlled size ranges and hydrophobicity, with conventionally milled platinum-bearing UG2 ore and the bulk reverse flotation of hematite ore. A novel bench-scale continuous column flotation cell and continuous mechanical hybrid cell with large relative froth volumes, as well as a three-phase froth stability column were used to characterize the froths.It was found that froth stability could be related to the concentrate particle surface area by a Langmuir-type relationship. This is indicative that the mechanism by which particles stabilize the thin films in froths is similar to the mechanism by which surfactants lower surface tension. Different froth stabilities were found for different ores and this was thought to be the result of different particle sizes and distributions, which resulted in different packing densities in the thin films and Plateau borders. Interestingly, there was a clear relationship between the feed particle size and the froth stability even though froth stability was dependent on the concentrate particle surface area. It seems that the feed particle size is a good predictor of the surface area of particles in the concentrate. Concentrate particle size did not show a clear relationship with froth stability since it was already shown that it is both the size and the amount of the particles in the froth that contribute to the stability.INTRODUCTIONThe stability of the froth in froth flotation is important to the recovery and grade of the valuable mineral. Too stable a froth and the grade is reduced; not stable enough and the recovery may be compromised. Platinum-bearing ores with fragile, poorly mineralised froths are known to have froth recoveries that are routinely less than 10% (Crosbie et al, 2009). There are a number of chemical, physical and operating parameters that can affect froth stability, including reagent dosages, air flow rate, pulp density and particle properties. Arguably, the largest contribution to froth stability is from the particles that stabilise (or destabilise) the thin films in froths. Particle size, hydrophobicity and shape all affect froth stability to some extent."

Jan 1, 2016

By D. Eriksen

Zero Emission Gas power, ZEG, is a novel concept where a high temperature solid oxide fuel cell (SOFC) is integrated with a reforming reactor producing hydrogen from natural gas through Sorption Enhanced Steam Methane Reforming (SESMR). The SOFC is used as a high temperature heat source for regeneration of the CO2-absorbent. Moreover, by using part of the produced hydrogen as fuel for the SOFC, the waste heat of the process is considerably reduced. Thus, the process has a very high thermal efficiency and produces both electricity and hydrogen from natural gas. In addition, a stream of pure CO2 is produced in the regeneration step and can be deposited or used commercially. Initial cost estimates indicate a cost of electricity and a cost of hydrogen well below today's prices. A small (1kWel + 1kW H2) demonstration set-up is under construction and experimental results and related research will be presented. This set-up comprises one 2.5kWth H2 SESMR-reactor (about 0.85 Nm3/h H2) operating batchwise with dolomite as the CO2-sorbent. The reactor developed is designed like a parallel plate heat exchanger where the mixture of sorbent and reforming catalyst is packed between the heat exchanging plates. The demonstration set-up includes a 1kW SOFC operating in a continuous mode. The set¬up will therefore demonstrate continuous simultaneous hydrogen- and electricity production, but cannot demonstrate simultanuous electricity- and CO2-production. The set?up is well equipped for on-line monitoring of gas composition, flows and temperatures. This important part of the demonstration set-up is developed and provided by Christian Michelsen Research (CMR). A minor part of the project is the development of a continuous circulating fluidized bed SESMR-reactor system and in another related project the focus is on the development of more suitable sorbents. In these two projects co-operation with University of British Columbia and Lousianna State University, respectively, is highly appreciated.

Jan 1, 2005

Everybody would agree that a good roadway leads to more efficient haulages by reducing haul times, smoother and safer operation for operator and less wear and tear on tires and equipment, thus improving availability and overall costs efficiency. There is a number of factors that come into play to achieve this especially when developing a mine. Excavations of Ramps and Headings: Operators should follow surveyors and layouts accurately while driving ramps. To maintain constant grades on ramps, which leads to better design control of water and easier grading of roadways. Dips and dives lead to needless over excavations and unnecessary cost and disposal of waste rock. When dressing a ramp some areas may require 2 to 3 feet of material to correct the dips and perfect to constant grade. You may ask yourself, is this all necessary? A small exercise is to follow a loaded haulage truck up ramp. At the first hump, grade change, notice the down shift and notice how far the truck travels to regain the up shift and his speed. The difference is remarkably noticeable when the grade is constant. All this leads to less driveline shock, less horsepower demand, better fuel efficiency and more productivity. Drill & Blast Patterns to control water for Ramp Headings: The drill pattern needs to allow for a ditch. A slight cross fall to form a ditch can easily be done with the lifters. The preferred side of the ditch is always the inside curve of the ramp as it has less tendency to erode roadbed material. On a level, the ditch is dictated by the sump location. A blasted ditch will eliminate water pounding and keep the roadbed dry. Water trapped in roadbed is the major cause of rollout and de-stability of roadbed. If the water is allowed to drain in the middle of the ramp it will cause erosion, movement and loss of fines and an increase in grading intervals.

Feb 1, 2008

By Charles Graham

For hundreds of years the standard vertical mine shaft was rectangular shaped and timber lined. There are many advantages to rectangular shafts but as mines became deeper the circular shaft became more popular. The chief advantages of circular, concrete lined shafts are their ability to resist lateral pressure and they offer less resistance to ventilation air. A number of elliptical shafts have been sunk in an attempt to realize the advantages of both the rectangular and the circular shaft. A concrete lined elliptical shaft provides better space utilization than a circular shaft, would allow for shaft sinking with two double drum hoists, as well as concurrent level development. The design also makes one sided stations possible and provides for a simple headframe design.

Feb 1, 2008

By Q. Dong, S. A. Nightingale

An investigation has been carried out to assess the effects of an applied voltage on the dissolution rate of MgO refractory in a steelmaking like slag. In this study corrosion results obtained from dip tests using a dense direct bonded MgO refractory in a CaO-SiO2-Fe2O3-FeO-MgO slag are presented. These results demonstrate that the application of a voltage across a dense MgO refractory-slag interface can change the rate of refractory dissolution. For the slag composition used and the voltage range tested, it was found that a maximum corrosion rate was obtained at a voltage setting of -0.45V. The results of this investigation have been explained in terms of voltage affects on Marangoni (interfacial tension induced) stirring and its effect on the MgO dissolution reaction that is at least partly controlled by mass transfer in the slag.

Jan 1, 2004

By Larry Urbanoski

"This paper describes the application of a radioisotopic energy dispersive X-ray aY1alyser to complete on-stream analysis in a base metal concentrator.The major components of the system are outlined and some description of the application, operating experiences and benefits are provided.IntroductionThe ma1n intent of this paper is to describe the on-stream analysis system in operation at the Geco concentrator. X-ray analysis systems installed in Canadian concentrators to-date may be broadly classified as wavelength dispersive analysers whereas the installation described herein is an energy dispersive x-ray analysis system. Energy dispersive x-ray analysis techniques may utilize radioactive sources to provide primary x-rays for excitation of elements and separate the secondary x-rays on the basis of energy levels. In contrast wavelength dispersive analysers apply high voltage x-ray tubes to provide primary x-rays and utilize crystals to disperse and thereby separate x-rays generated by bombardment of the sample."

Jan 1, 1978

By David F. Machuca-Mory

Modelling the geometry of a vein is a crucial step in resources estimation. The resulting models are used as mineralization domain boundaries and have a direct impact on the tonnage of estimated resources. Deterministic models are often built using time consuming wireframing techniques usually based on hand interpretation of the drillhole intercepts. Another approach consists in coding the drillhole samples by a function of their distance to the veins contacts. The coding is subsequently used for modelling the vein contacts away from drillholes. This is a more efficient approach and is able to provide a measure of tonnage uncertainty. The use of location-dependent variograms improves the modelling by incorporating local changes in the anisotropy of the vein structure. This combined approach results in more realistic vein models, particularly when the geometry of the vein has been are altered by folding, shearing and other structural processes. The approach is illustrated on a realistic case study.

Oct 1, 2009

By Karen M. Moffitt

Developments in mining methods and rates have led to an increase in the frequency and size of waste dump failures that have not been adequately predicted or explained in terms of conventional slope stability analysis. Monitoring data and visual observations suggest a unique mode of failure responsible for large runout events. A numerical model has been developed to capture commonly observed patterns of deformation, and investigate the formation of the ensuing failure mechanism. The analyses have yielded a good correlation with observed field behaviour and have provided significant insight into the coincident stresses and deformations within the dump. Results indicate that while creep effects in the waste dump could have a significant effect on the magnitudes of displacement, the overall dump stability is governed by the strength of the foundation soils underlying the toe region. Consideration of both the stress and velocity fields leads to factors of safety for various dump heights and foundation slopes that are considerably less than predicted from limit equilibrium analysis. The results suggest that conventional limit equilibrium analysis techniques may not be adequate when assessing the stability and design of waste dumps on steeply sloping terrain.

May 1, 2001

By J. E. Udd, L. B. Geller

"Responding to requests by the Canadian mining industry and the mine regulatory authorities, the Canada Centre for Mineral and Energy Technology (CANMET) undertook a major research project on evaluation of wire rope testing in 1986. The objectives were to document, analyze, and clarify - in basic operational terms the reasons for ongoing mine shaft wire rope failures that occur despite mandatory non-destructive testing (NDT) with electromagnetic (EM) instruments on a routine basis.The project's investigative scope and depth was unprecedented. It could not have been successfully completed without the wholehearted cooperation of industry, research organizations, and mine-inspectorates at both national and international levels.The project's goals were attained. II was shown that, at present, the problem areas in Canada are oj a human , rather than of a hardware-related nature. Consequently, the principal recommendations are concerned with a more widespread, more uniform and thorough operator training and certification process at industrial and regulatory levels. Secondary suggestions concern areas of hardware-related improvements.In this paper an up-to-date general overview is given of the major project results. A n extensive reference list is also provided of papers that contain all relevant documentation in detail."

Jan 1, 1992

By Jean-Luc Collins

"The paper deals with the impact of fleet imbalance on a deterministic evaluation of shovel fleet productive capacity. It shows that if the fleet imbalance is overlooked, then estimated fleet productive capacity will be overrated.The paper shows that fleet imbalance inflates utilization, and care must be taken when using such statistics which are derived from reported field-equipment-hours. It shows that the utilization must be deflated by a factor called 'balancing efficiency"" in order to estimate shovel productive capacity correctly. The paper also shows how fleet imbalance can be controlled by managing idle time or downtime in an actual operation.The technique used for measuring the balancing efficiency factor is based on statistical analysis of equipment utilization."

Jan 1, 1980

By M. Al-Hilal, G. Rajja, A. Al-Ali, Y. Jubeli

Abstract -A radiometric survey was carried out over clastic sediments in the immediate vicinity of some phosphatic sediments of Cretaceous age in the Wadi Qasser Al-Hallabat basin of central Syria. The objective was to explore for uranium and to define its dispersion pattern. This was based on ground radiometric surveys and geological studies. All ground surveys (using radon emanometry, track etching, gamma-ray survey and geochemistry) gave similar results, outlining the locations of the radioactive phosphatic formations in the basin, and indicating the dispersion pattern of uranium in the clastic sediments in the surrounding area. The dispersal of uranium from upper Cretaceous phosphatic formation occurs by mechanical weathering and chemical leaching by oxidizing surface waters. A rough estimate is that about one-third of the original uranium content of the Cretaceous sediments has been dispersed. Mechanical erosion is responsible for the main part of this released uranium, which now occurs in Recent sediments. However, the occurrences of spotty secondary U mineralization indicates that another small part of the available uranium must have been chemically leached out by the prevailing oxidizing waters, forming minor surficial minerals.

Jan 1, 1998

By A. R. Barnes, R. Pandher, T. Shannon, P. Gover

Following the closure of the Glencore Zinc Brunswick mine, the Glencore Brunswick Smelter has transitioned to treating external feeds, and currently treats a number of secondary Pb-Zn concentrates. Processing these concentrates has in some cases been challenging due to the diverse mineralogy of the feeds. Certain feeds are difficult to ignite or show inadequate sulphur removal during oxidation on the sinter strand, while in other cases, combinations of feeds produce a sinter with unsuitable properties for further handling. This paper discusses two methods developed in collaboration with XPS Consulting & Testwork Services to characterize these feeds prior to processing them and to identify which ones are most likely to pose challenges during processing.

Jan 1, 2014

By H. Gharahbagheri, S. Shafiei Zadeh, H. Hassan Nejad

Waste Electrical and Electronic Equipment (WEEE) is one of the fastest growing types of solid waste in the world, and often contains precious metals, especially gold. Gold processing and recovery from secondary materials, especially WEEE, have been under investigation for more than a decade now; however, a comprehensive review that illuminates the future path is missing in the literature. The aim of this short paper is to discuss the recent advances in gold processing and recovery from secondary electronic materials and why it has not yet become practical. The role of pyrometallurgical and hydrometallurgical methods, as well as their advantages and disadvantages will be discussed; however, the focus will be on Biosorption and recent advances.

Jan 1, 2014

Resistance spot welding is the most common type of welding in the automotive industry. In RSW the size and shape of welding nugget is one of the most effective factors on mechanical properties, such as tensile shear strength and fatigue strength. so properly adjusting the variables of the welding is necessary .in this study the effect of different parameters of RSW including time, current, electrode force, geometry of electrode so diameter and angle of electrode tip in the shape and size of welding nugget evaluated. for experimental procedure, low carbon steel sheet st12 is used. the process is simulated with finite element method by using ANSYS software. for the formation of welding nugget a 2 dimensional symmetrical model electrical-thermalmechanical is used and for elevate the accuracy ,we determined the properties of material related to temperature. The results show that increasing the time and current of welding, the diameter of spot weld also increased and the role of current is more impressive. and also increasing the electrode force decrease the diameter of the nugget due to increasing the contact area and decreasing the resistance .increasing the diameter of electrode tip cause increasing contact area and decreasing the resistance and decreasing the diameter of the nugget. furthermore, changing tip angle and electrode diameter don't show sensible change in the geometry of the welding nugget. comparison between simulation and experimental result show a good adaption.

Oct 1, 2011

By L. A. Wolff

"Second only to profitability (but not always), productivity is the most sought after measurement for any operation. Whether it is in mining, manufacturing, construction, etc. managers always strive to know how productive various plants are. Even the Federal Government publishes, on a monthly basis, the nation's factory productivity.Just what is productivity and how is it measured? This is an important topic that needs definition. There could be as many definitions as there are people who use it. In the mining industry, the problems of defining productivity would be analogous to the definition of equipment availability. Each mine uses its own definition to suit its needs. Webster's Dictionary primary definition for productivity is ""the quality or state of being productive,"" with productive defined as ""yielding or furnishing results"". This is a definition open to a broad spectrum of interpretation. A discussion of how productivity is currently used in the mining industry and an introduction to a potentially different approach to its measurement and meaning is outlined in this paper.Defining ProductivityTypically, mining companies track several productivity measurements. These are partial measurements and can include the following: tons per specific equipment class per hour, tons per man-hour, and tons per shift. None of these, however, track the over -all performance of an operation, that is, a unit of output per unit of input.For a mining operation, output can be defined as the ore for mill processing. Input includes the required components of production to get to the first step of processing.The Wesbter's Dictionary definition exposes a major fault with the popular conception of productivity. The critical issue of accountability is not addressed. Anyone can produce, but how effectively and efficiently are resources used? Quantifying an inclusive measurement is difficult. Statistics referring to an increase in productivity are often published. For example, the statement, ""gold productivity has increased by 10%"" has many potentially dangerous interpretations. One must ask, what does this statistic really mean? Did gold companies produce 10%” more gold? Were less manpower or equipment required to produce an equivalent amount of gold? Did ore grades increase resulting in more ounces of gold produced, etc. Obviously, production and productivity can have similar implied applications and meanings, but also two different, distinct meanings.To mitigate a problem like this, a standard needs to be developed within the mining industry. Because of varying ore grade, changing waste to ore ratios, different mining methods, etc. all of which have a direct impact on mining, development of a standard is difficult. Kendrick(1) discusses the use of Total Factor Productivity as a productivity measurement. Summarized, the total factor productivity measure is an indication of the change in efficiency in the use of basic labour and capital factors associated with an operation.This measurement has little meaning when calculated at a given point in time. It should be an on-going calculation, tracking an operation over a period of time, to evaluate trends. These trends can be used to determine if an operation's productivity is what it should be, and alert management to potential problems before they become major and adversely affect an operation."

Jan 1, 1990

By Nirmal Weerasekara, Jochen Franke, Malcolm Powell, John Favier

Mill liners serve the dual purpose of protecting the shell from wear and transferring the rotary motion of the mill to an effective grinding action. As the liners wear, the efficiency of energy transfer changes, so there is balance between liner profile for wear and for milling efficiency. A tool that can simultaneously predict the evolution of the liner profile and the associated change in milling efficiency should prove most useful in optimal liner design. This paper presents such an approach, based on measured 3D liner profile data informing 3D DEM simulations of charge motion and liner wear modelling.

Jan 1, 2012

By M. Lundström

The Outotec HydroCopper® process is a novel technology, developed and registered by Outotec Technology Oy, for leaching copper from chalcopyrite using cupric chloride solution. The leaching process is operated at atmospheric pressure in a stirred tank reactor, at temperatures near the boiling point of water and pH values between 1.5 and 2.5. During the leaching of chalcopyrite in cupric chloride solution, a reaction product layer forms on the mineral surface. In the present work, the formation and the composition of the reaction product layer was studied in an environment similar to that of the HydroCopper® process. The effect of the process parameters on the reaction product layer was investigated. Electrochemical measurements, including A.C. impedance spectroscopy and microscopic observations were carried out and an equivalent circuit was used to determine the surface parameters, such as the reaction product layer capacitance and the charge transfer resistance. The results suggest that, at low pH, a passivating sulfur-rich layer forms, whereas at high pH, a more porous iron-rich layer was detected. The values measured can give useful information for optimising the leaching parameters of the HydroCopper® process. Cu2007

Jan 1, 2007

By M. Cimenti

Fuel cells have tremendous potential as power sources but much fundamental research is still required. One key component of the research is the experimental set-up used. In particular, the placement of the reference electrode is extremely significant in measuring the half-cell overpotential of solid oxide fuel cells, since differences in area, misalignments, and also differences in the kinetics of the working and counter electrodes can cause both scaling errors and frequency distortions of the measured impedance. The impedance of thin solid electrolyte cells of different electrode geometries has been calculated using the finite element method and the results compared to experimental values obtained for the oxygen reduction reaction on platinum.

Jan 1, 2005

By H. Saari, M. Pates, P. C. Patnaik, A. Merati

Single crystal nickel-base superalloys such as PWA1484 exhibit superior performance compared to conventional superalloys, and are used extensively in turbine blade applications requiring good high temperature properties. The life of these blades is typically limited by cracks and erosion. Due to the high cost of these blades, welding techniques are being considered to weld/repair worn components, extending their useful lives and delaying the need for expensive replacement components. However, the sensitivities for solidification cracking and post weld heat treatment cracking are relatively high in these alloys. Electron beam (EB) welding can deliver concentrated heat sources and has the potential to address these issues. Numerous welding trials and structural tests must be conducted to identify the optimum method and welding parameters. Weldability is studied over a range of material conditions, welding parameters, and directions. The influence of welding parameters on the fusion zone microstructure and resultant weldability is investigated using combination of microscopic examination and micro-hardness testing. This paper summarizes some of the results of a feasibility study conducted to understand the effects of welding parameters on localized microstructural features, cracking sensitivity, and mechanical properties of autogenously EB welded coupons of single crystal PWA1484.

Jan 1, 2004

By V. Pouyafar

In recent years semi-solid processing of steel alloys has gain more attention among researchers. Production of high quality complex steel parts with higher mechanical properties is the final goal for all these researches. A thorough understanding of the flow behavior of the metal under investigation is the key for a successful process design. The material used in this research is M2 tool steel. The experiments were performed using a Searl-type concentric cylindrical rheometer which is specially designed for high temperature rheological measurements up to 1500 ºC. The rheological techniques were consisted of continuous cooling experiments and isothermal holding and also shear rate step change experiments for different solid fractions. Based on the rheological data a single phase thixotropic model has been derived and adopted to the measured data. The state of the microstructure has been applied through a structural parameter. The model fits well with the experiments.

Oct 1, 2011