Search Documents

By S. Kelebek, Gerhard W. Heinrich, Peter F. Wells

"The review and optimization of process stages is an integral part of the program to improve the metallurgical performance of the Strathcona Mill. Improved primary grind size distributions, streamlining of rougher-scavenger circuits and increased platinum recoveries were the target of plant and laboratory scale tests. The results can be summarized as follows:• Decreasing the primary grinding cyclone vortex finder diameter for nickel/copper ore gave significant increases in overall copper recovery and improved rougher flotation selectivity.• The scavenger flotation stage in the circuit treating copper ore was found to contribute little to this circuit's copper recoveries -yet to be essential for acceptable recoveries of nickel, platinum and gold. The elimination of this stage by re-routing the tailings from the copper ore rougher into the nickel/copper ore rougher feed has lead to lower gangue recoveries to the nickel concentrate and to improved copper-nickel separation, while reducing equipment operating costs.• Surface aging effects such as oxidation are known to decrease flotation recoveries of platinum minerals such as sperrylite. The conditioning of an intermediate non-magnetic process stream with copper sulphate prior to thickening increased the platinum recoveries in the subsequent flotation stage by approximately 10%."

Jan 1, 1996

By N. Afrin

The microstructure and tensile properties of AZ31B-H24 magnesium (Mg) alloy after friction stir welding (FSW) were evaluated. The grain size was observed to increase from approximately 5 µm to about 9 µm after FSW. The obtained Hall-Petch type relationship showed a strong grain size dependence of the hardness values. While the FSW led to about half of the yield strength of the base magnesium alloy, the ultimate tensile strength after FSW could reach about two thirds of that of the base alloy. The hardening capacity of the FSWed samples was about twice of that of the base alloy. The strain hardening exponent of the base alloy was found to be about 0.1 whereas it became larger than 0.3 for the FSWed samples. After yielding the base alloy showed a high initial and almost constant work hardening rate, corresponding to linear hardening stage II, followed by stage III with a decreasing hardening rate. Stage II linear hardening was observed to be absent in the FSWed samples.

Jan 1, 2007

By Shae K. Kim

The aim of this study is to manufacture magnesium alloys with alkaline earth metal oxides (BeO, CaO, MgO or SrO) additions with the objectives of (1) ensuring safety during processing and applications by raising the ignition temperature and reducing oxidation, (2) protecting the environment by reducing or eliminating use of protective gases, (3) maintaining or improving elevated temperature properties with lower amount of Ca or Sr or rare earth metals when compared with conventionally developed high-temperature magnesium alloys, (4) developing cleaner strip casting and continuous casting processes without hot tearing and (5) obtaining all of these objectives without sacrificing mechanical properties or increasing the cost of magnesium alloys.

Jan 1, 2006

By Geoffrey C. Streeton

A continual objective of mine operations is to reduce ground control costs without compromising the overall safety or performance of the installed ground support. Any change in the ground support regime must not result in a less secure or safe workplace. The due diligence required to implement a change in rockbolting practice is extensive, particularly when the new bolting system has not been used at any other mining operation. Factors such as yield, shear strength and embedment strength must all be investigated to gain an understanding of how the rockbolt can be expected to perform. This paper also discusses the substantial cost reductions and efficiency gains which can be achieved through the introduction of the Jumbolt rockbolt.

May 1, 2001

By R. Bridge

Mining companies are progressively finding themselves having to develop operations for more complex, deeper ore bodies, which require the use of more complicated mining and mineral processing methods. This coupled with the generally increasing trend of higher capital and operational costs have led to a need in the industry for improving ore body knowledge, mining and mineral processing. Geometallurgy is a relatively new concept that can link the three aspects, and when used effectively it is a method that can produce the necessary information for designing and building operations for reliable and optimum performance. Geometallurgy not only involves the integration of geological, mining, and metallurgical fields, but it can also be expanded to include environmental and economic information to produce a block model that can be used to obtain the best outcome in terms of plant response and plant sustainability. The geometallurgical program should not end once the block model has been populated. A detailed geometallurgical approach should be applied to all stages of the operation encompassing sample selection, through to equipment sizing and production forecasting. It can also become a useful optimisation tool thereby allowing the operation to be proactive rather than reactive against changes in the ore characteristics. With the development of metallurgical performance predictors it is possible to quantify how the ore will behave in the process plant in terms of throughput, recoveries, reagent consumption, etc. Therefore, in terms of responsible mining and sustainable resource development, a geometallurgical approach to operations is the logical step for plant development. In this paper we describe the state of the technology with respect to the application of geometallurgical modeling and its utilisation in the fields of design, forecasting and optimisation of mining operations.

Aug 1, 2013

By Fulchand Shende

Around the world many potash mines experience brine inflow problems. The presence of brine in underground excavations may induce structural and stability problems. A study has been carried out to simulate the effect of brine on the performance of pillar support. The testing program consisted of loading potash specimens in a creep frame, and simulating inflows by continuously pumping brine into an experimental cell. Brine temperatures and load conditions were varied to simulate several mining and inflow conditions. Specimens were fitted with acoustic emission transducers to monitor energy emissions during an eight-hour test duration. Samples of brine were also collected to provide K+ and Na+ concentration data necessary for an accurate assessment of the dissolution process. Test results indicated that dissolution rates are highly dependent on brine temperature and load conditions. Loads approaching 50% UCS tend to generate very high rates of energy emissions, often leading to the failure of the simulated pillars. This study demonstrated that acoustic emission could be effectively used for predicting the performance of pillars when exposed to inflow brine.

May 1, 2001

By M. Fairman

The effect of welding speed on the microstructure of friction stir processed (FSPed) AZ31B-H24 magnesium alloy was studied using light microscopy, image analysis, and microhardness tests. The grain size of the magnesium alloy was observed to increase after FSP from about 3.5 µm in the base alloy to about 8 µm in the stir zone. The aspect ratio decreased from 1.60 to 1.55 towards the center of the stir zone. The changes in the grain size and shape caused the microhardness of the samples to drop significantly across the FSPed region from 75 HV in the base alloy to below 55 HV in the stir zone. Decreasing the welding speed increased the grain size due to a greater input of heat energy. The faster heating rate due to the lower welding speed caused a deeper penetration of the annealing effects of FSP. It was also observed that the annealing effects caused by FSP were less pronounced with increasing distance from the interface between the sample and pin tool shoulder. The Hall-Petch type relationship of the micro-indentation hardness as a function of the grain size was observed to hold true after FSP.

Jan 1, 2007

By R. B. Humphrey

Cut-and-fill mining methods at the Thompson Mine have undergone significant changes since production began in 1961. Changes have been introduced in almost all aspects of the mining operation, from the original timbered chutes and air-operated slushers to the present-day bored raises, footwall ore passes and load-haul-dump units. This paper describes the evolution of mechanized cut-and fill mining methods, highlighting the changes in design for stopes and service openings, ground support methods; hydraulic filling and ventilation systems. A mechanized stoping area is described from the initial mining concept through design, development, construction and mining cycles.

Jan 1, 1979

By W. Schubert, N. Radoncic

"The term “squeezing” is frequently used, although it is ill defined. Definitions like “large and long lasting displacements” raise the questions about the threshold values for the magnitude and duration of displacements. Large displacements during tunnelling frequently are observed in fault zones with high overburden. Whether this causes problems very much depends on the design approach used. On the one hand, the magnitude of expected displacements has to be predicted prior to excavation to provide for enough allowance for the displacements without violating the clearance profile. On the other hand, the support characteristics must be compatible with the expected imposed strains. As the magnitude of the displacements and thus the strains in the support depend on the support capacity and its characteristic (yielding potential), only well engineered systems will be successful.Experience in Alpine tunnels over the last decades has shown that closed shotcrete linings can sustain a strain of approximately 0.8% to 1% without failure. Any strain above this value inevitably leads to failure of the lining, and thus a loss of resistance, causing additional displacements. Based on a large number of simulations, a criterion for a critical overburden depth up to which closed linings can be used has been developed. Traditionally open gaps in the shotcrete linings have been used to allow for larger strains. To enhance the efficiency of the linings, yielding elements have been developed, which are integrated in the shotcrete lining, allowing large strains and controlled development of support resistance (Figure 2). When designing such yielding support systems, the development of the displacements, as well as the rheological behaviour of the supports must be considered. As the development of displacements to a large extent depends on the face advance, also the advance rate has to be considered, to be able to compare the time-dependent strength of the lining to the stresses developing as a result of the imposed strains. Another issue is the compatibility of the rock bolts with the large strains. With standard grouted bolts, there is a potential that the “fresh” grout is sheared due to the initially large strain rates. Special rib designs of the bolts allow for a higher strain tolerance.For successful tunnelling through fault zones quality monitoring and up-to-date data evaluation is of crucial importance. With advanced evaluation tools, changes in the ground conditions ahead of the face can be reliably predicted. With the help of empirical relations, the development of the displacements for different advance rates and supports can be predicted, allowing for the determination of the required overexcavation.The paper presents a review of the development of ductile elements, methods of analysis, and monitoring data interpretation."

Jan 1, 2015

By M. Sokoto, H. Hata, K. Nishina, K. Haiki

Fluoride ions in zinc electrolyte cause corrosion to aluminum cathode plates at zinc electrowinning process, so we have developed an iron compound as a fluoride ion adsorbent used in zinc sulfate solution. The iron compound is synthesized from FeC13 solution with a small amount of sulfate ion by neutralizing reaction with Na2CO3 solution. The fluoride ions adsorbed on the surface of the iron compound are desorbed in alkaline solution and the iron compound can be reuse as a fluoride ion adsorbent. Moreover, if adsorption capacity of the iron compound decreases, it can be dissolved in HCl solution and re-synthesized.

Jan 1, 2008

By J. Groppo, W. Zhang, R. Honaker

"The flotation of monazite is depressed when using hydroxamic acid as a collector in the presence of calcium ions which may exist due to the dissolution of minerals such as calcite. Minor dosages of sodium hexametaphosphate (SHMP) were found to effectively depress calcite, whereas the flotation of monazite was not impaired in single mineral flotation tests. However, in a mixed mineral flotation system, monazite flotation was depressed significantly. The mechanism of hydroxamate adsorption on monazite and calcite, the depression mechanism of calcite on monazite, as well as the depression mechanism of SHMP on calcite and monazite were studied using micro-flotation, electro-kinetic, and adsorption tests. Findings indicate that the adsorption of hydroxamate on monazite was due to chemisorption while adsorption on calcite was a result of physical interaction. SHMP significantly increased the negative charges of calcite surfaces which depressed the adsorption of the hydroxamate anions on the calcite surfaces due to an elevated electrostatic repulsion force. When calcium-rich minerals such as calcite are mixed with monazite, the calcium ions dissolved from the mineral surfaces specifically adsorb onto the phosphate oxygen sites on the monazite mineral surfaces thereby causing depressing effects. The addition of SHMP to suppress collector adsorption on the calcite surfaces interacts with the calcium species that were specifically adsorbed onto the monazite surface, which prevents hydroxamic acid adsorption onto the rare earth oxygen sites due steric hindrance and results in the flotation depression of monazite. INTRODUCTIONAs one of the commercial rare earth ores, monazite has been widely exploited to produce additives for catalysts, batteries, alloys, etc. Because of the complexity and the fine nature of some monazite ores, methods such as gravity, magnetic, and electrostatic separation to treat beach sand monazite fail to produce satisfactory concentrates, suggesting the use of floatation is warranted (Cheng, Holtham, & Tran, 1993). The primary associated minerals of monazite ores include ilmenite, quartz, zircon, rutile, sillimanite (Dixit & Biswas, 1969; Pavez a& Peres, 1994, 1993). Using sodium oleate as collector for monazite has been reported in many studies (Cheng et al., 1993; Dixit & Biswas, 1969; Pavez & Peres, 1994, 1993). Several investigations have reported maximum floatability of monazite occurring at pH values between 8 and 9 (Cheng et al., 1993; Dixit & Biswas, 1969). A study conducted by Pavez and Peres (1994) compared the use of hydroxamate and sodium oleate for the treatment of a monazite ore and found that hydroxamate significantly improved the grade of rougher concentrate."

Jan 1, 2016

By Eric D. Monrad

Supply chain simulation modeling is taking on a more prominent role in mining project planning and decision making. Transportation costs for the supply chain can form a significant component of the overall cost to provide product to the end customer. In recent years, computing power has increased, simulation software has advanced, and simulation specialists have become even better equipped to provide sophisticated analysis and recommendations. This has led to a virtuous cycle of owners expecting and supporting data-driven analytics, which drives further advancement. This paper discusses developments in supply chain planning and two case studies from recent simulation modeling analyses.

May 1, 2013

By C. Okay Aksoy

In Turkey, the increasing demand for lignite has necessitated an increased emphasis on both lignite production and recovery. This emphasis has resulted in a gradual increase in the application of the retreat longwall mining method for both its product recovery and productivity benefits. Also, in order to maximize the recovery of the natural resources and to increase total production, it is necessary to take advantage of underground reserve before abandoning the mine. This means that at the end of the life of the mine, the main drift safety pillar and the shaft pillar will generally be extracted. This investigation a preliminary study of the stability of the main drift and the shaft at the Hustas Mine as the safety pillars are extracted. In this study, field surveys belonging to the underground colliery of Hustas Co. in Soma have been investigated with the help of LAMODEL working under the Laminated Displacement Discontinuity principle for the models calibrated as a results of physical model and finite element analyses. The convenience of Laminated Displacement Discontinuity Analysis has been researched in such studies. The results out of the models have been coherent with the previous studies.

May 1, 2004

By L. C. Hsu, M. O. Desilets, P. J. Lechler, Jr. Bonham, J. G. Price, L. J. Garside

Geochemical background levels have been established for unmineralized sedimentary rocks that are elsewhere the hosts of Carlin-type gold deposits in the Getchell Trend. The Paleozoic rocks in the Winnemucca Quadrangle consist predominantly of the lower Paleozoicsiliceous and clastic sequences that were carried eastward along the Roberts Mountains thrust during the Late Devonian and Early Mississippian Antler Orogeny and the late Paleozoic Havallah and Pumpernickel sequences brought along the Golconda thrust eastward during early Mesozoic Sonoma Orogeny. Over 260 rock samples were collected from the Paleozoic sequences. Major and trace elements were determined by instrumental methods best suited for the specific elements. The general geochemical features of the Paleozoic sedimentary rocks are discussed in detail with reference to the data of average abundances of elements in sedimentary rocks. The background and threshold values of certain trace elements in sandstone, shale, and carbonate rock of one formation, as well as back-ground levels for the entire sequence were obtained. The characteristic geochemical features of the Paleozoic rocks in this area include: consistently high Ba and low Au contents (1.1 ppb, 1.5 ppb, 1.1ppb Au for average sandstone, shale and carbonate, respectively); generally low contents of those elements which may be of environmental concern such as As, Cd, Hg and Pb. Plots of major and trace elements suggest that the majority of the Paleozoic clastic rocks are related to a passive-margin tectonic setting. Samples with gold values higher than threshold are considered to have been affected by hydrothermal alteration related to gold mineralization. Most of these samples generally also have higher values of Sb, Hg, V and/or As. These observations support the use of such elements as pathfinders for gold, although V has not been identified as such before. Ba is not effective for gold exploration in this area due to the generally high background value of Ba, even though it may be an important pathfinder elsewhere.

Jan 1, 1995

By A. Singh

Deformation structures after tensile and compression tests on Mg926Zn64Y alloy extruded at 250°C and 400°C are studied, in as-extruded and heat treated conditions. The icosahedral phase particles stimulate recrystallization during extrusion, resulting in fine grain size. Tensile and compression tests at room temperature show comparable yield strength, with a yield asymmetry ratio up to 0.98. c-type dislocations are observed in the grains near the submicron size icosahedral phase particles. The source of these dislocations is believed to be dissociation of <c+a> type non-basal dislocations. No dislocation pile-ups on icosahedral phase particles are found. {10 1 2} type twinning occurs in compression.

Jan 1, 2006

By G. T. Lapidus, O. J. Solis-Marcial

Currently, ores with high-grades of copper oxides and secondary sulfides have become increasingly scarce, which has encouraged industry to look for alternative raw materials to obtain copper. The problem is that primary sulfides are difficult to dissolve at near ambient conditions. Proposed hydrometallurgical processes have not been implemented beyond a pilot or demonstration scale. One of the principal disadvantages is that the majority of these processes are not viable with ores that contain less than 4% copper. One of the more recently proposed techniques involves the use of organic solvents in the dissolution of copper concentrates with a chalcopyrite content of between 20 and 30%, which has shown high efficiency. The present research explores the ability of this process to leach copper from low grade chalcopyritic ores (<4% Cu) at different temperatures ranging from 20 to 50°C. It was found that depending on the temperature, high percentages of copper were extracted in 40 to 100 minutes, using different oxidants. Additionally, distinct leaching behavior was observed with each oxidizing agent. In some cases, the extraction kinetics adjusted to the diffusion controlled shrinking core model.

Jan 1, 2014

By A. R. MacPherson

"This paper considers four aspects of autogenous grinding. Part 1 discusses statements on power efficiency of autogenous grinding compared to conventional crushing and grinding systems. It also demonstrates how high-power efficiency can be obtained from autogenous grinding systems. Part 2 considers a simple method of testing ores to determine the type of autogenous plant which can treat these ores on a commercial basis. A comparison of testing for simple small plants vs large plants or complex ores is included. Part 3 considers important aspects which have to be considered in proper design of an autogenous grinding system. Part 4 discusses problem ores and how they can be treated in an autogenous system. INTRODUCTIONAfter about 35 years of using autogenous grinding plants in the mining industry, it is perhaps time to review where we are with this, by now, relatively old development. Autogenous grinding in this paper means grinding run-of-mine ore by fully autogenous means or by using a ball charge to assist the grinding (semi-autogenous). Also, autogenous grinding can be eitherby dry or wet.The use of autogenous grinding in the fifties was making its slow start, and it was not until the sixties that more of the mining industry would consider its use . By the seventies, most builders of new plants would have considered autogenous grinding, whether they used it or not, in the final design.In the eighties, most large plants use autogenous mills and to reduce over-all operating costs, many older conventional plants are now looking and actually retrofitting these old plants with autogenous grinding mills.It is evident that many misconceptions concerning autogenous grinding are still current. Some come from improperly designed plants which result from poor test work. There are many considerations in the proper design of autogenous plants. Some ores have been found to give problems even in a well designed plant. These ore types are beginning to be classified and recognition in the test stage allows steps to be taken in the design so that these ores can be efficiently handled in autogenous grinding plants.Therefore, this paper will address the following aspects of autogenous grinding:1. Misconceptions regarding autogenous grinding.2. Testing of ores to ensure a well designed commercial plant.3. Important considerations in mill design.4. Difficult ores, their recognition and types of design to handle such ores."

Jan 1, 1989

By Georges Houlachi, Akram Alfantazi, Maysam Mohammadi

Manganese ions in zinc electrowinning electrolytes form a protective MnO2 layer that ultimately decreases Pb contamination in the zinc product. In this study, the effect of dissolved Mn2+ on the electrochemical performance of Pb, Pb-Ca and composite Pb-MnO2 anodes was investigated. The properties of the MnO2 layer formed on these anodes were studied and compared. Potentiodynamic polarization and cyclic voltammetry experiments were performed in 180 g L-1 sulphuric acid to study the electrochemical reactions occurring on the anodes. The anodes were subjected to galvanostatic polarization at 50 mA cm-2. The morphology and uniformity of the MnO2 layer on the anodes were examined using scanning electron microscopy (SEM). Experimental results revealed that the MnO2 layer formed on the composite anode was more compact and uniform compared to that formed on the Pb and Pb-Ca anode. It was also observed that the cell mud formation rate, and consequently manganese ions consumption, depended on the anode type. Although initial formation of the MnO2 layer decreased the oxygen evolution overpotential, its growth might negatively affect electrocatalytic activity of the anodes.

Jan 1, 2014

By Alim Ullah

Danieli entered into the Direct Reduction (DR) field in order to offer its clients complete turnkey facilities for steelmaking?from processing of raw materials through finished products. The Danarex® Process produces a passivated product, called the Supermetallic (SPM), without hot-briquetting. One of the main features of the Danarex® Process is its ability to produce approximately 50% of the Direct Reduced Iron (DRI) through reduction gas generated in a reformer and another 50% through recycling preheated furnace exit gas. Some other distinguishing features are: separation of carburising and cooling zones and the use of double bustle for better distribution of gas inside the shaft furnace. A pilot plant was set up at Hazen Research, Inc., Golden, CO in order to show that the integrated process works as expected and to obtain process data. The SPM obtained was of a very high quality, evidenced by metallization levels of 92% to 98%. The carbon content could be controlled between 1.5% to 4.0% by varying the operating conditions and approximately 75% of this carbon was present as Fe3C. The product was tested for inertness by Chilworth Technology, England, using UN standard tests and was found to be safe for outdoor storage and transportation.

May 1, 2003

By A. Otsuki

"This paper discusses the primary collector adsorption onto a sulphide mineral in mixed collector systems to understand its adsorption mechanism. UV-vis measurements were performed to identify the primary collector concentration adsorbed on pyrite, and the adsorption kinetics under different conditions were compared to distinguish their difference between single and mixed collector systems. Small amount of secondary collector addition prior to the primary collector addition significantly improved the adsorption kinetics of primary one. The result was explained by the combination of two previously proposed mechanisms (i.e., different adsorption site mechanism and multi-layer product mechanism). This study showed UV-vis measurement as an effective tool to study mixed collector adsorption behaviour.INTRODUCTIONCollectors are surfactants composed of heteropolar molecules with a non-polar and a polar group (Lotter & Bradshaw, 2010). In a froth flotation process, the function of collector is to improve the hydrophobicity of target minerals and selectively float them with the aid of gas bubbles. Because of the chemical or physical attraction between the polar group and the mineral surfaces sites, collector molecules adsorb on the particle surface with the non-polar group assigned towards the bulk solution (i.e., water), thus the mineral particle surface becomes hydrophobic (Wills & Napier-Munn, 2006).Thiol collectors are major collectors widely used in sulphide mineral flotation. Potassium amyl xanthate (PAX), dithiocarbamate (DTC), dithiophosphate (DTP), mecaptobenzothiazole (MBT) are some common thiol collectors. Previous studies reported that some mixed collectors systems enhanced the flotation performance (e.g., Bradshaw, 1997; Bradshaw et al., 1998; Rao & Forssberg, 1997). Thiol collector mixtures are often used in the flotation of sulphide ores, and discussed with the synergistic benefits (Bradshaw et al., 1998) which include lowering the total collector dosage requirements, improving the sulphide recovery and the rate of flotation as well as the improving the froth characteristics. The current paper mainly considered the mixture between two thiol collectors (PAX and DTC, considered as a weaker and selective collector, and stronger and less selective collector, respectively (Bradshaw, 1997)) to further understand their adsorption mechanism that should assist in improving the flotation performance of refractory gold ore."

Jan 1, 2016