Search Documents

By H. J. Ni, M. Y. Huang, S. W. Chen

The effects of several fluxes on purification, microstructures and properties of A00 aluminium have been studied. The experimental results and analyses indicate that many cracks and large porosities exist in the surface film above the melt purified by C2Cl6 and that the film is floe and mostly composed of AhO3 and pure aluminum, which carries many carbon particles and AlCh not fully volatilized. And then over 50% of the all-melting residue is pure aluminum, which is one of the major reasons for high melting loss. Moreover, because of a mass of gas bubbles and a state of seethe, there exist many inclusions which size is under l0µm in the microstructure of A00 aluminum purified with C2Cl6 or fluxes containing C2Cl6- With this purifying method, the aluminum crystal grains are extended along the radius that was observed firstly and the average crystal size of A00 aluminum are about 100µm~150µm. In addition, small size inclusions have little affected on tensile strength and micro inclusions under l0µm have little affected on elongation.

Jan 1, 2006

By J. B. Rubenstein

This work demonstrates the feasibility of using confocal surface profilometry to measure and characterize wear of graphite anode surfaces. This method was tested using anode samples that were electrolyzed for 24 hours in a laboratory-scale magnesium cell with a high oxide molten salt electrolyte. The oxide produced accelerated wear on anodes designed for low oxide electrolytes. Contour maps, which are effective at displaying non-uniform wear, and total graphite consumption values were generated from the collected surface coordinates. Along with both qualitative and quantitative analysis capabilities, this measurement system was shown to have a fine resolution and a low detection limit.

Jan 1, 2004

By H. Houali

Corrosion is an electrochemical process that causes degradation and deterioration of various steel works (pipelines, drains, cisterns) whether they are buried, immersed, or not. Worldwide, we estimate that corrosion destroys a quarter of the annual production of steel at a rate of 5 tons per second. Several techniques are used to protect against corrosion. Among these processes, Cathodic protection, which is regarded as the best technique to assure the protection of steel, works against this phenomenon. This is achieved either by a system of reactive anodes, or by the technique of impressed current protection or other techniques. Before any installation of cathodic protection, a preliminary study and pre-evaluation of certain parameters must be made. In the present work, we will present an example of dimensioning of an installation of cathodic protection by imposed current of a pipeline using solar energy, where we discuss the following items: ? Evolutions of the potential as well as current along the pipeline and their respective expressions deduced from the laws known as telegraphists; ? Range of protection (potential of protection along the pipeline); ? Influence of the isolation resistance of the coating on the range of protection; Effect of the aging of the coating and its influence on the current of protection

Jan 1, 2005

The recovery of fine hydrophilic gangue in flotation is related to the recovery of water. Water is carried by bubbles as a film and wake into the froth. The amount carried (entrained) depends on bubble size, gas rate and the subject of this paper, frother type. To isolate the effect of frother type from that of bubble size and gas rate, gas holdup is used as the correlating variable. Measurements were made using a bubble column (no solids) operated continuously with the overflow recycled. Continuous operation meant some foam depth was required to ensure only entrained water is recovered. Using an automatically controlled 7cm foam depth the overflow rate of water is used as a measure of 'water carrying rate'. It is shown that the common frothers can be grouped into four families based on the water carrying rate-gas holdup relationship.

Jan 1, 2006

By Staff

Introduction The Hedley mine, perhaps better known as- the Nickel Plate mine, is one of the outstanding properties of southern British Columbia. Discovered in 1898 by Woollison and Arundell, prospectors, the property was bonded in 1899 to M. K. Rodgers for the Marcus Daly Estate, of Butte, and development was started the same year. From the high grade of the ore outcrop, and its colour, due to oxidation of the arsenopyrite, it was not difficult to open up and trace the showing. The Nickel Plate ore-shoot, which apparently had been easy to follow on surface, was more difficult to trace underground. In 1903, prospecting on an adjoining property, the Sunnyside, showed commercial ore at surface, but it was only after two years' work that the ore-body was defined and shipments started. From this property, $1,200,000 have been taken out. Prospecting was also carried on on the IXL, Climax, Copper Cliff, Mound, Bulldog, Exchange, Silver Plate, Gold Plate, and other properties, all of which had surface showings, but up to date only the Nickel Plate, Iron Duke, Morning, and Sunnyside have produced commercial ore. In 1904, the Bulldog looked like a very promising mine, but it failed to make good. In 1905, the Sunnyside No. 1 was in the limelight, but it also failed to make the grade. In 1906, an outcrop on the Sunnyside No. 3 looked interesting. Subsequent work. on this claim produced $840,000, and at the same time ore which yielded $400,000 was mined from the Sunnyside No. 4. In 1908, the Nickel Plate ore-body entered a lean zone and, as the diamond drill failed to give satisfactory results, the Daly Estate, after making a profit of $1,151,000, sold the property to the Hedley Gold Mining Company, Limited, for $760,000, retaining, however, a large interest.

Jan 1, 1929

By Burrows. A.

Temperature profiles in the lead smelter sinter bed at Xstrata Zinc Mount Isa sinter plant have been measured using a wireless temperature probe. Corresponding sinter samples have been collected for characterization. The sinter peak bed temperatures were found to be in the range of 1000 - 1200 °C. Microstructures and softening temperatures of these sinters have been characterised. Strong correlations have been observed between peak bed temperature and peak hood temperature, and between mean sinter softening temperature and peak bed temperature. It was found that higher peak bed temperature results in higher sinter softening temperature. For the feed material used in the trials, to obtain sinters with mean softening temperatures above 1050 °C, peak bed temperatures above 1130 °C are required. There appears to be a direct correlation between granule size distribution in the feed and peak bed temperature attained. High peak bed temperatures are observed in sinters with narrow granule size distribution.

Jan 1, 2008

By I. P. Swainson, A. Ilbagi, H. Henein

Powders of Al-50wt%Ni, Al-40wt%Ni and Al-36wt%Ni were produced using the Impulse Atomization technique, a rapid solidification technique. The molten droplets were cooled in-flight by the stagnant helium or nitrogen in the atomizing chamber. The resulting powders were sieved into different size ranges. X-Ray diffraction and neutron diffraction were used in order to quantify the phase fractions in the samples. The computer software GSAS was used to calculate the weight fraction of the existing phases, namely Al3Ni2, Al3Ni and Al, by profile refinement method. The effect of processing parameters, alloy composition and particle size will be discussed in this paper. In brief, no AlNi was found in any of the samples analyzed. Higher cooling rates resulted in the reduction of the ratio of Al3Ni/Al3Ni2. Also, at high cooling rates, Scheil closely predicted the ratio of Al3Ni/Al3Ni2. Some metastable phases were found in Al- 36wt%Ni.

Jan 1, 2010

By Robert D. Brown

"Important tax changes, many of them of direct interest to the mining industry, were contained in the budgets brought down by federal and provincial finance ministers across Canada this spring. This month, Tax Notes presents a brief summary of important tax changes introduced at the federal and provincial levels in the last few months.IntroductionIn the March 1980 issue of the CIM Bulletin, Tax Notes surmised that the short-lived 1979 budget proposals of the former Conservative government offered a unique glimpse of budgetary changes that might be unfolded in 1980. Scene II of this ""now you see it-now you don't"" drama opened on April 21, 1980, when Finance Minister Allen MacEachen, in an ""economic statement""' reintroduced a selection of tax proposals taken from the ill-fated Conservative' budget of December 11, 1979, but refused to bring forward major new proposals in tax and finance.Mr. MacEachen proposed a 5% surtax on federal corporation income tax to apply in the 2 years from January 1, 1980 to December 31, 1981, as a slightly modified version of the same surtax proposed by former Finance Minister Crosbie in his December budget address. Mr. MacEachen also reintroduced a number of technical amendments which would affect the taxation of mining income in certain instances. In addition, a large number of other tax proposals suggested in the previous Conservative budget were also reintroduced, although there are some notable omissions."

Jan 1, 1980

By T. Hidayat

The distributions of minor elements between slag/metal and slag/matte in equilibrium with tridymite in the Cu-Fe-O-S-Si-Al-Ca system have been investigated in the range of conditions of interest to the high- temperature copper production, refining, and recycling processes. An improved experimental methodology has been used involving high temperature equilibration in controlled gas atmospheres, rapid quenching, and quantitative microanalysis techniques using Electron Probe X-ray Microanalysis (EPMA) and Laser Ablation Inductively Coupled Plasma Mass Spectrum (LAICPMS). The effect of oxygen partial pressure on the distributions of minor elements between slag/metal and slag/matte has been accurately measured. The effects of slagging components (Al2O3 and CaO) on the distributions of minor elements between slag/metal have also been experimentally determined. The present study is a part of a larger integrated experimental and thermodynamic modelling research program in the systems relevant to high-temperature copper processing. INTRODUCTION In the high temperature processing of copper, minor elements are distributed between different phases, i.e. liquid slag, liquid matte, and liquid metal. From a processing perspective, it is desired to have the valuable minor elements distribute predominantly in the metal and matte phases rather than in the slag phase, and to have the non-valuable minor elements distribute predominantly in the slag phase rather than in the metal and matte phases. Knowledge of the distributions of minor elements between phases in the smelting, converting, and refining processes is required if the distributions of minor elements between phases in these processes are to be optimized.

Jan 1, 2019

By P. Czaja

The paper presents a patented and copyright protected concept of constructing a shaft lining that goes through rock masses having strong rheological properties and being susceptible to leaching. In the case of salt layers, especially at significant depths (over 900 m) the relative convergence of the heading contour may amount to 40 ?/year. That results in the fact that any other method of securing the shaft lining, e.g. by making it flexible, will not be sufficient to ensure the stability of the shaft reinforcement geometry. In the new shaft lining concept the excessive rock creep into the outbreak inside the shaft diameter will be removed by local and controlled leaching of the shaft cheeks by means of fresh water directed through a porous medium at the contact layer behind the watertight tubing lining. The paper presents the structure of such a lining and an outline of the construction technology. In order to implement such a lining, a typical tubing will be applied. Separate design and manufacturing will be required for the technological rings used to control the leaching process behind the lining.

Aug 1, 2013

By R. E. Phelan

Introduction The Flin Flon deposit was discovered by Tom Creighton, an experienced prospector and trapper, who in 1914 made his headquarters at The Pas, Manitoba, and still lives there. The discovery was made in the fall of 1914, and Creighton and his associates spent the next summer in investigating the find. In August of 1915 the first claims were located. The property was optioned to Hayden Stone & Company, and in the spring of 1916 they started a diamond-drill campaign. Hayden Stone spent $50,000 on the property and, among other things, completed over 7,500 feet of diamond drilling. The ore not being as high grade as expected, and also being complex in character, Hayden Stone then abandoned their option. In the spring of 1917, Messrs. Earle, Faskin and associates took an option on the property and started an extensive drilling campaign. This campaign accomplished approximately 18,000 feet of drilling and secured for the Faskin interests a 32 per cent interest in the property. In 1920, W. B. Thompson and The Mining Corporation of Canada secured an option, and, while this option was in force, sunk two shafts in the ore-zone and did a considerable amount of drifting and cross-cutting in the ore to study the manner in which it occurred in place, and, by actual channel sampling, to check the grade indicated by the previously accomplished diamond drilling. All of this work had indicated that an ore-body existed on the property containing at least 18,000,000 tons of ore, assaying as follows: gold, 0.074 oz./ton; silver, 1.06 oz./ton; copper, 1.71 per cent; and zinc, ). 45 per cent (1). Complete analyses of composites from the drill holes showed that the ore was very complex in character. It contained the above values in gold, silver, copper, and zinc, as well as large amounts of sulphur and iron, and traces of lead, arsenic, antimony, cobalt, and various other metals. Although the ore was obviously pyritic in character, pyritic smelting, the usual method of treating this class of ore, could not be used to beneficiate the ore with any reasonable expectation of making such a venture a financial success, since coke and coal landed at Flin Flon would be expensive, and siliceous flux was known to be scarce locally and low in grade. The property therefore lay idle until 1925.

Jan 1, 1935

By J. R. del Castillo, J. Ruiz, N. Kuyucak, J. Chavez

Environmental Impact Assessment (EIA) and Feasibility Studies (FS) were carried out to evaluate the potential use of treated acid mine drainage (AMD) occurring at the Kingsmill Tunnel in the Central Andes of Peru. The 11-km long tunnel drains the underground works of the Morococha Mining District and discharges about 1.25 m3/sec of AMD directly into the Yauli River, which is located within the Amazon Basin. The communities living downstream cannot use the Yauli River water due to its low pH and elevated concentrations of metals (e.g., Cu, Zn, Fe, Mn, As, Cd) and sulfate. Studies carried out for this project included technical feasibility, EIA, economic viability and social impact assessment phases. During the "Technical Feasibility" phase, the treated AMD was produced by simulating a high density sludge (HDS) lime neutralization/precipitation process and was evaluated for various potential uses. Mining companies located in Morococha, in particular Centromin Peru S.A., and the Water Works Company of the City of Lima (Sedapal) collaborated with Golder Associates during the studies. The Canadian International Development Agency (CIDA) provided the financial assistance. The results of the physical, chemical, biological and toxicological analyses demonstrated that the treated AMD could be used for supplementing the drinking water supply of Lima and for agricultural (e.g., irrigation and livestock) and recreational purposes. Process design and scale-up parameters were also determined for the implementation of the full-scale treatment facility to the site. The use of the treated AMD as a drinking water supplement would be economically feasible.

Jan 1, 2004

By P. E. Mather, M. J. M. Krane

Uncertainty quantification is a means of articulating the reliability of model estimations. Models of copper pyrometallurgical processes have been published for decades but discussion of their reliability has typically been terse and qualitative, mitigating understanding of their exact applicability to industrial situations. This presentation shows basic uncertainty propagation and Bayesian model calibration, two powerful uncertainty quantification tools, applied to a reduced order model of copper fire/anode refining. The implications of the uncertainty quantification analyses on the applicability of the model results to industrial practice are then discussed. Finally, other possible applications of uncertainty quantification to copper extractive metallurgy are explored. INTRODUCTION Modern copper production operations, including mining operations through wire drawing factories, are ubiquitously heavily instrumented. Most mine-sites and smelters have large repositories of historical data. That said, much of this data is not exploited to its maximum effect. This proceeding provides examples of using uncertainty quantification (UQ) to maximize the informational yield of the data collected from a fire-refining operation. Anode/Fire Refining is the final pyrometallurgical step in the production of copper anodes; it is an essential and universally employed processing step at smelters (Schlesinger, King, Sole, & Davenport, 2011). Much like the smelting and converting furnaces further up the process stream, anode furnaces are difficult to instrument due to their high temperature and the corrosive and/or caking quality of their offgas. This makes continuous and accurate measurement of the streams leaving the unit operation, e.g. liquid copper, slag, and offgas very difficult. As an example, offgas flowmeters, while providing continuous draft values, could miss the actual draft value by tens of percent due to caking or corrosion. UQ methods account for the uncertainty in process measurements and parameter values; they use a process model with measurements of performance indices to provide better and better estimations of process performance. This proceeding will first introduce a surrogate model for copper fire refining, made from a 1D, transient, reacting flow model of the process presented elsewhere in these proceedings (Mather & Krane, 2019). Discussion of the data used to make the surrogate model, as well as the creation of the surrogate model, will be included. Then, a Monte Carlo simulation will be performed, showing the expected soot production rate based on the surrogate model and assumptions about the uncertainty in the model’s parameters. Finally, the surrogate model parameters will be calibrated in a Bayesian way; this will tell what the actual uncertainty in the parameters are, given a set of observed industrial data and prior assumptions of the observations’ and parameters’ uncertainty.

Jan 1, 2019

By Frank Lemy

This paper presents an application of digital face mapping in an underground mine. Based on photographs it was possible to construct discontinuity maps, which were used to characterise the rock mass. The results were compared favourably with values obtained through scanline and area sampling mapping for the same site. The case is made for digital mapping as a safe, fast, and efficient way to characterise rock mass structure for engineering purposes.

May 1, 2001

By B. Loveday, G. W. Delaney, S. Cummins

"Applying DEM to prediction of tumbling mill performance is challenging because several different modes of breakage are active in the process. As our knowledge of breakage and computational capacity improve, it is worth revisiting previous simulation tasks which did not produce a satisfactorily realistic description of a measured process. At SAG 2006, we reported the simulated and measured outcomes of treating a well characterised ore in a 1.2 m diameter mill. This well instrumented, pilot scale mill at the University of KwaZulu-Natal has been combined with some new approaches to ore testing to allow different modes of breakage to be tested. The mill design allows the rate of generation of fine material to be measured in close to real time for autogenous and SAG mill charges. The updated simulation model estimates mass loss with particle evolution and embeds the cumulative damage and breakage.The simulated results are compared with the measured results. Issues such as relating modelling inputs to particle breakage characterisation data and the accuracy of the predictions of the models are discussed."

Jan 1, 2012

By A. Singh

"Flotation of fine (< 10 µm) minerals is a challenge exacerbated by the emerging practice of fine grinding flotation feed to better liberate targeted minerals; however, the ability of conventional flotation cells to float liberated fines remains questionable. The Gold Ore solution using Mach reactors was tested at Mintek, South Africa, and showed an ~180% increase in the Kelsall kfast factor, a projected recovery improvement of 4% for the Mach-reactor case, and final concentrate grade twice that of conventional flotation. Theory, pilot plant results, and key aspects of plant design, supplemented by operational plant observations after commissioning, are discussed.RÉSUMÉ Le procédé de flottation de minerais fins (< 10 µm) pose de grandes difficultés, lesquelles sont aggravées par la pratique émergente de l’alimentation du circuit de flottation avec des mailles de broyage très fines pour mieux libérer les minéraux ciblés ; la capacité des cellules de flottation classiques à flotter les fines de minerais libérées reste cependant discutable. La solution proposée par la société Gold Ore, qui utilise des réacteurs Mach, a été testée à Mintek, en Afrique du Sud ; elle affichait une augmentation d’environ 180 % du facteur kfast développé par M. Kelsall dans son modèle de flottation, une amélioration prévue de la récupération de 4 % dans le cas du réacteur Mach, et une teneur finale des concentrés deux fois plus importante que celle obtenue avec la flottation classique. Sont débattus dans cet article la théorie, les résultats générés par l’usine pilote ainsi que les principaux aspects de la conception de l’usine complétés par des observations relatives à l’usine en activité après sa mise en service."

Jan 1, 2018

By Bevan. P. A.

The general location, topography and climate are discussed briefly, together with an historical record of the deposit. General geology, grade control and ore reserves are covered at some length, and reasons are given for the operation being placed on a salvage basis.

Jan 1, 1973

By G. Barbery, P. Dauphin

"In order to obtain reproducible and reproducible results in batch flotation, researchers have tried various approaches, from normalized testing, to modifying existing cells, and even designing new machines. The paper reviews the basic concepts that must be fulfilled in a laboratory flotation machine, and present the FLOTOMATEC design, which results from five years of testing and development. In addition to providing accurate measurements of air flowrate, power consumption, agitation speed, the cell eliminates most operator induced errors. Results of experiments comparing FLOTOMATEC to a conventional cell, as well as reproducibility tests are given. Introduction The use of batch flotation machines in mineral processing research and development is very common. These machines have been used for many years without almost any change in their design, instrumentation or automation. Various authors since Raffinot (1960) have criticized the available designs, especially with respect to the large errors that are introduced by the manual mode of operation. Barbery et al. (1986) have presented a review of the problems involved in laboratory testing in flotation research.Batch laboratory machines should have the following characteristics:"

Jan 1, 1989

By P. A. Christopher, R. H. Pinsent

"The Adanac molybdenum porphyry deposit near Atlin, in northwestern British Columbia, was discovered in 1905. It was explored extensively between 1967 and 1980.The deposit is within a complex, multi-phase, quartz monzonite stock that is a satellite of the post-accretionary, Surprise Lake Batholith. Biotite K-Ar dates range from 703 ± 2.4 Ma to 71.6 ± 2.1 Ma, indicating a Late Cretaceous age of emplacement.The deposit comprises an irregular-shaped ring or halo peripheral to a quartz monzonite porphyry dome, or ""cupola': The shape of the ring, and of a smal~ fine-grained quartz monzonite intrusion, and the presence of higher-grade mineralimtion on the eastern flank of the cupola, suggest partial control by a preminera/ structure. The deposit is truncated by a steep, northwesterly dipping, normal fault (Adera Fault) that down-dropped the northern half of the deposit by a minimum of 100 mThe deposit lacks strong zonal alteration but there are narrow envelopes of potassic alteration around some veins and local zones of intense wall-rock silicification. There is considerable retrograde alteration along postminera/ faults and fractures.Molybdenite occurs in veins and fractures, many of which are relatively flat-lying. They occur in all phases of quartz monzonite. Molybdenum is the only element of economic significance. There are vein and skarn occurrences with tungsten, tin, lead, zinc and precious metals peripheral to the deposit.In 1981, Placer Development Limited reported an ""undiluted mineable mineral reserve"" of 151 971 000 tonnes grading 0.063% Mo at a cutoff grade of 0.04% Mo and a strip ratio of 1.5:1."

Jan 1, 1995

By M. S. Ünal

Creation of 3D model of coal seams is a tedious and time consuming operation. Computer aided 3D solid modelling of coal seams can be performed in a fast and detailed manner. However, in case of having tectonically disturbed coal seams where faults may be observed, expert opinion is necessary to decide the geometry of the coal seam. The aim of this study is detection of fault zones with computers by using drill hole data. Firstly, a digital database is generated by using the drill hole data. Surface models of the layers are produced by applying triangulation method on coal seam roof elevations. The generated surface is divided into small squares and consequently dip and dip direction values are calculated for each square. Variograms for dip and dip direction are determined and maps showing the variation of dip and dip direction are generated by using geostatistical methods such as kriging and co-kriging. Examination of disconformities observed on estimation maps created by kriging and co-kriging clearly reveals the extension of faults. The method used in this study is applied to detect fault lines of a known mine field. 3D solid modelling of the coal seam has also been performed by using conventional cross-section method. The results of both methods were in good agreement. Identification of major faults by using the method introduced in this study could certainly simplify 3D solid modelling of coal seams.

Aug 1, 2013