Search Documents

By F. W. Wellmer

"I would like to comment on the classification scheme of ore reserves based on geestatistical and economic parameters as proposed by Wober and Morgan in the CIM Bulletin, January 1993.In principle, a classification system that combines quantitative data for levels of confidence and errors with economic expectations must be welcomed. I would like to point out, however, two aspects of the proposed classification system which might create ambiguities, and therefore problems, by working with two levels of confidence and two kinds of block sizes. A normal classification scheme reflects the information density, the highest reserve category such as class A, or proven, or measured reserves having the highest density. This is not necessarily the case in the scheme of Wober and Morgan (1993), unless the definitions are amended.I. Assuming, as the authors do, that the estimation errors show an approximately normal clistribution, at the 95% confidence level, the standard deviation has to be multiplied by about 2 for the error and, at the 84% confidence level by about 104. Reserves (or resources) with the same or even higher information density than class A reserves, which at the 95% confidence level would not fulfill the required economic criteria at the threshold level, i.e. not qualify as ""ore"" at all, could be retained ""on paper"" to class B reserves by just multiplying the standard deviation by the factor 104 instead of 2, thereby narrowing the error.This statistical ambiguity was partly inherent in the old German classification scheme which used varying confidence levels and errors (GDMB 1956; Jahns 1959). In the new German scheme, which was later adopted in Austria in a moclified version, the level of confidence was therefore fixed at 90070 for all reserve categories (Wellmer 1983; ONORM 1989)."

Jan 1, 1993

By Md. Rashedul Islam

Magnetic data was collected from the Yeoju historical sites using the fluxgate gradiometer through six sites & several grids. We measured the vertical gradient by the FM256 Fluxgate gradiometer. The readings were logged every half meter. The obtained data were processed and treated to introduce a high quality magnetic image. The gradiometer results defined various positive and negative magnetic anomalies, which revealed the existence of several archaeological features of different shapes and sizes. The study of the process magnetic images give us a concept that the subsurface features are caved shape stone chamber tombs, burial mounds, deep room structure, Yeoju mausoleum, pagoda?s square foundation stones, walls etc. All these are superior work of early Goguryeo inheriting orthodox Silla style. So, the study area may have great archeological interest.

May 1, 2009

By Mei-Yan Yang, Qiu-Ying Wang, Ltd. Yunnan Yuntong Zinc Co., Guo-Mu Chen, Meng-Yang Huang, Peng Zeng, Guo-Feng Li

"Historically, alot of jarosite was found in the leaching residue when leaching indium from secondary zinc oxide materials. The reasons for the formation of indium bearing jarosite were theoretically analyzed. The influence of controlling the acidity and the addition of reagents on the indium leaching yield during secondary zinc oxide processing was investigated. In order to increase the leaching yield of indium, a measure of controlling the creation and destruction of jarosite was proposed. The production data shows that the leaching yield of indium was increased from 60 to 96%, and the content of indium in leaching residue simultaneously decreased from 900g/t to 100–200g/t when implementing such controlling measures.INTRODUCTIONIndium does not occur as independent minerals in the earth’s crust and is mainly associated with complex sulphide minerals. Specifically some sphalerites can contain as much as 900g/t of indium. Most indium is recovered from by-products of copper, lead or zinc metallurgy. Therefore, the research on the recovery of by-products in non-ferrous metallurgy is important(Sinclair et al, 2006). The main technologies used for this objective in China include: •,pre-neutralization-reduction-precipitation indium process(Yu et al, 2008), •,countercurrent oxidizing acid leaching process and sulphation roasting-water leaching process(Cao, 2005), •,oxygen pressure acid leaching of zinc concentrate-P204 extraction process(Yang et al, 2006), •,doubleacid leaching-solvent extraction process on lead dross from a reverbatory furnace flue dust(Liu, 2003),•,an acid leaching-solvent extraction process on smelting ash(Zhouet al, 2005). Although high pressure and extreme conditions can be used to improve extraction from high iron bearing indium residues(autoclave processing), mild extraction with lower cost and lower environmental impact are preferred.This paper describes both how the indium extraction using mild conditions in a secondary zinc circuit was quite low and, how through XRD and chemical analysis jarosite formation was found as the main cause. The paper then proceeds to discuss a method for improving the leaching yield and the application of this method in industrial practice."

Jan 1, 2016

By Jorge Lema Patino

"The purpose of this paper is to determine the best techno-economic alternative for the treatment of tin ores, when comparing the various mining and metallurgical methods of preconcentration, concentration, volatilization (fuming) and up to the final stage of selling to the smelter. The study of the influence of the different parameters of cost, recovery and quoted prices has motivated the paper, which aims at determining the best process of ore treatment in terms of its techno-economic feasibility.Method of WorkOn the basis of head grades of 0.5, 0.75 and 1.0% tin, the following alternative methods of treatment are possible:1. Mining-Concentration-Smelting.2. Mining-Preconcentration-Fuming-Smelting.3. Mining-Concentration-Separation, with direct smelting and fuming/smelting of the two fractions produced.The calculations were carried out on the basis of existing information and publications concerning the various experimental recoveries in the operating mills of COMIBOL. In the case of concentrates containing less than 10% or more than 40% tin, extrapolation was required.The final grade of the tin concentrates and the gross weight of the concentrate were calculated on the basis of the estimated recovery curves. The costs of the preconcentration and the concentration stage s were determined per gross metric ton of material treated.The calculation of the cost of the smelting stage is similar for all the alternatives, the royalties and smelting charge varying with the grade of the final concentrate. In the fuming stage, a uniform recovery of 90% was taken in all cases so as to obtain a final concentrate grade of 65% tin, regardless of the head grade of the feed material.For the separation stage, the following considerations apply:a) Separation can be carried out by gravity separation or flotation methods.b) The cost of separation varies depending on the system used.c) The distribution of tin in the two fractions is 100% at this stage. In other words, there is no loss of tin during separation."

Jan 1, 1982

By Xianglin Yang, Hong Zhong, Jingjing Xiao, Guangyi Liu

"The selective adsorption of a flotation collector to a mineral plays a crucial role in enhancing the hydrophobicity of targeted mineral particles for attaching air bubbles in pulp. The recent progress of the structure-reactivity relationship of flotation collectors, the characterization methods for mineral surfaces with adsorbed collectors and their commercial application are reviewed in this paper. Particular emphasis is placed on the density functional theory (DFT) for understanding the reactivity of new collectors, the surface analysis techniques including time-of-flight secondary ion mass spectrometry (ToF-SIMS), in situ scanning electrochemical microscopy (SECM) and atomic force microscope (AFM) to characterize mineral/collector interface, and the flotation technologies for optimizing recovery of valuable minerals. Especially, the recently developing collectors such as Gemini, alkoxyalkylthiourea, dithiourea, amide-hydroxamate and oximido-thiol surfactants, and their specificity to given minerals are evaluated. Based on this crucial review, it is evident that the structural modification approaches for minerophilic or hydrophobic groups, and combined surface analysis approach for further understanding the adsorption mechanism of collectors on mineral surfaces will lay a solid foundation for the future development of flotation collectors. INTRODUCTIONIn mineral processing, flotation is the main process for separation and recovery of valuable minerals from the ores contained them (Fuerstenau et al., 2007). One of the key requirements in flotation process is to increase selectively the surface hydrophobicity of the targeted minerals by collector adsorption so that these mineral particles can preferably attach to air bubbles in a slurry or pulp (Fuerstenau et al., 2007). Flotation collector is a kind of functional surfactant, which is composed of polar and non-polar groups (Somasundaran, & Wang, 2006). Non-polar portion, commonly being linear, branch or ring hydrocarbon group, is termed hydrophobic group. The polar portion, exhibiting strong affinity to mineral surfaces, is known as minerophilic group (Nagaraj, 1988). According to mineral types including saline, oxide and sulfide minerals, flotation collector divides into sulfide and oxide mineral collectors. For efficient recovery of valuable minerals from the refractory complex ores, insights into the adsorption mechanism, hydrophobic model and subsequent flotation approach of flotation collectors have been regarded as an indispensable issue in mineral processing."

Jan 1, 2016

By Mohamed Sassi, I. Kolo, R. L. Sousa, R. K. Abu Al-Rub, Manhal Sirat

"Fractures induced by folds are pivotal in hydrocarbon exploration, ground water transport and harnessing of geothermal energy. This is because of the need to predict and understand fracture propagation in reservoirs which have folded rock formations. Despite its prominence, there is a lack of reliable numerical models for simulating fractures resulting from rock folding. This is partially due to the difficulty involved in fracture modelling. As a contribution to fold-fracture modelling, this work applies a coupled plasticity-damage model to rock fracturing and anticlinal folds. Parametric studies on a single folded layer give insight into the fold formation and behaviour. The anisotropic continuum damage model which considers both tension and compression is formulated using the power damage evolution law. For ease in formulation, strain equivalence hypothesis is adopted whereby the strain is the same for both damaged and undamaged configurations. Lubliner plasticity yield criterion is adopted for plastic deformation. The model is coded in Abaqus user subroutine UMAT and is applicable to quasi-brittle materials.INTRODUCTIONThe understanding of fractures in the earth’s crust helps in the prediction, evaluation and characterization of fractured reservoirs, whether they are petroleum, geothermal or underground water reservoirs. This is partly because reservoir permeability and stability are dependent on fracture properties (Nelson, 2001). To achieve this, various approaches have been developed to analyze reservoir rock fractures. These could be grouped into (a) discrete approaches – where the rock mass is represented by a finite number of well-defined components and (b) continuum approaches – where the mathematical assumption of an infinitesimal element is made (Jing, 2003). Ivanova (Ivanova, 1998) comprehensively studied fracture systems in nature and highlighted folds as one of the major geologic settings that produce fractures. Naturally occurring folds in reservoirs sometimes compound fracture analysis. It might not be clear whether the fractures formed before, during or after rock folding. Fractures formed during the folding process are expected to show stress orientations related to folding and are thus of primary concern in rock folding simulation. It could be argued that there are no numerical models that as"

Jan 1, 2015

By A. Gakwaya, P. Vachon-Joannette, P. Gagnon, J. Lévesque

"Predictive numerical methods are essential tools for reduced development cost and improved high performance designs of modern aircrafts. Their use leads to savings in terms of design cycle time and experimental trials. Composite materials subjected to impact loadings demonstrate various damage modes such as matrix cracking, fiber breakage, delamination and, ultimately, fabric fracture. Composite laminates are extensively used in the aerospace industry, and their damage modeling is complex due to their inhomogeneity and anisotropic behavior. Damage evolution affects both in-service properties and performance of these composites. In this work, the drop-weight impact test has been simulated. Using a material model that accounts for both delamination and intralaminar damage, laminates response is analysed using numerical simulations based on 3-D finite-element models of the commercial code Abaqus/Explicit. Experimental and simulation results are compared, in terms of energy absorption and contact force. The obtained numerical results show good agreement with experimental data.INTRODUCTIONAs primary aircraft structures are increasingly being made from advanced fiber-reinforced polymer matrix composites and are in general exposed to a variety of impact scenarios (bird, hail, debris etc.), an understanding of the impact event and the performance of composite materials during impact is important in the development of new structures. This work is focussed on low velocity impacts that typically occur when foreign objects hit the aircraft during maintenance or other on-the-ground operations. These impacts can cause non visible damage that affect the structural integrity of the composite components. While for metallic structures, damaging impact events typically leave noticeable dents due to plastic deformation, in contrast, for high strength carbon fiber reinforced composites, they can deform elastically to strain levels exceeding 1% and the internal damage can often occur without the formation of a visible dent. The identification and effect of impact damage on the performance of the structure is thus of great concern to the aircraft industry as the durability and damage tolerance of these composite structures are strongly influenced by the size of detectable internal damage."

Jan 1, 2016

By P. E. Georghiou, S. Shafiei Zadeh, H. Hassan Nejad

Data are presented on the extractant behaviour on toxic metal removal from spent hydroprocessing catalyst, produced at the North Atlantic Refinery plant in Newfoundland and Labrador. Aliquat 336 was selected due to its potential capabilities for the separation of cobalt, molybdenum and nickel from the leachate extractant produced by aqua regia. The solvent extraction process was statistically modeled using central composite design (CCD), and the numerical optimization was conducted to achieve the optimum point for toxic metal recovery for the extractant.

Jan 1, 2014

By P. K. Kaiser, F. Amann

"Rock mass characterization for deep underground construction and mining offers many challenges. This paper first describes some of the key challenges when characterizing highly stressed brittle rocks and then offers some guidance on how to arrive at reliable rock mass strength parameters for deep mining applications. Focus is placed on characterization for rock mass strength determination. It is illustrated how the common use of currently available rock mass characterization systems tend to underestimate the strength of rock at depth. Modifications to currently adopted approaches, i.e., the use of Geological Strength Index GSI for rock mass strength determination, are presented.INTRODUCTIONFor green fields projects, the first challenge of rock mass characterization stems from a lack of access to examine the rock mass at scales larger than typical core sizes (i.e., ~63mm in diameter) until late in the mine design when the flexibility for making changes is constrained. Hence, rock mass characterization often has to rely on information derived from boreholes alone (e.g., core, logs, etc.). This challenge is lessened when mines are expanded from existing operations. A second challenge is related to changing rock mass behaviour with increasing depth and stress. At depth, the rock is highly stressed, thus closer to failure, and often highly confined which leads to a higher interlocking with elevated strength but more brittleness. The goals of rock mass characterization are to be tailored to the technical goals of an investigation. For example, for cave engineering, the workflow includes the assessment of five key engineering aspects (Brown, 2007): Caveability; fragmentation; cave performance; extraction level stability; and mine construction (rock support). Each engineering aspect has to address specific engineering questions and each design component is influenced by different rock mass behaviour aspects and thus is dominated by different rock mass properties, e.g., the vulnerability to stress fracturing (spalling), the bulking characteristics for flow control and support selection, and the confining stress impact on pillar or support design. An effective rock mass characterization program, including logging, mapping and laboratory testing, thus has to collect and interpret features that are relevant for the above listed purposes. Some of the predominant factors are: block volume of defected and non-defected rock; spalling strength; tensile strength of defects; rock mass modulus; and rock mass strength parameters for application to low and high confinement design aspects."

Jan 1, 2015

By Robert B. Parsons

"While it might seem like heresy to suggest that ""taxation"" can be a source of financing, never the less some generous tax rules can considerably enhance the tax savings pertaining to a particular expenditure or project. A basic tax knowledge, and careful tax planning, can optimize government participation in a project. INTRODUCTIONIn trying to identify sources of financing for a project, ""government"" as a source of funding is normally thought of in terms of government grants, loan guarantees, interest rate buy downs, property tax waivers, hydro subsidies, and so on. Generally, such concessions are somewhat difficult to obtain, especially in the current period of apparent fiscal restraint. One source of government funding which should not be overlooked is the income tax regime, and, at the provincial level, the various provincial mining tax regimes.While the taxpayer would not normally view a tax system as a potential source of government financing, nevertheless various federal and provincial rules applicable to the mining industry can offer attractive tax deductions - and tax savings - with respect to particular expenditures. In fact, it is not unusual for a civil servant to refer to a tax deduction as a tax ""subsidy"". For example, in the right circumstances, the cost of a smelter expansion in New Brunswick would cost the operator only 31 cents on the dollar, with the federal and provincial governments paying for the other 69 cents by foregoing tax revenues (Table I). In a sense, such tax savings could be compared to a government grant equal to 69% of project costs. Of course, not every project expenditure will generate that degree of government funding. The fact of the matter is that the percentages of tax savings attached to different expenditures cover a wide range, depending on a complex mix of factors. The point to understand is that the tax rules can offer some valuable savings, even after tax reform, and that a basic knowledge of the tax rules can yield some fruitful rewards."

Jan 1, 1989

By Yoginder P. Chugh

Beginning in 2010, a scientifically-founded water spray system for continuous miners (CMs) has been in development at Southern Illinois University that significantly reduces respirable dust exposure for workers in the face area (patent pending). It includes engineered sprays around the cutting drum, outer bitring sprays, chassis sprays and side cutter boom sprays. About 3.6?4.5 m behind these sprays are additional sprays that cover the area between the CM chassis and the mine roof and ribs. The innovative spray system uses approximately the same volume of water as spray systems currently used on CMs and with similar operating pressures. The innovative spray system design also takes into consideration coal dust wettability. An Illinois mine decided to implement these concepts on a CM during the rebuild stage. Dust control performance of the rebuilt CM was evaluated using gravimetric dust sampling and real-time monitoring with multiple personal dust monitors. The average results based on gravimetric sampling of about 105 cuts show about 30 and 20% reduction in dust exposure for the miner operator and the haulage unit operator, respectively. Visibility in the mining areas was also significantly improved. Since the initial demonstration, the coal company has implemented the system on all of their operating CMs.

Aug 1, 2013

By P. J. Poirier, J. A. Meech, H. Raabe

"An Expert System has been implemented to assist operators in applying knowledge about froth conditions in the control of the flotation circuit at Highland Valley Copper. For some time, the personnel at Highland Valley Copper have recognized that froth type is a useful indicator of good operating conditions. However, the operating strategy based on froth type recognition is an ad-hoc skill in which different operators use a variety of terms, features and procedures to identify and solve problems. The first phase of this project developed an on-line consultative system to advise and tutor so that the diffuse expertise could be rationalized and consolidated into a standardized format.The second phase has brought this knowledge into a real-time environment to advise the operators on the floor in identifying froth types and troubleshooting corrective action. This paper describes the steps taken to acquire the knowledge, to design the required system features and to implement the real-time version of this system.INTRODUCTIONThe use of expert systems in the mineral industry has been gaining popularity in recent years. Minnova Inc, Les Mines Selbaie, Wabush Mines, Potash Corporation of Saskatchewan are just a few examples of Canadian mining companies that use expert systems to monitor or control their plants. Applications in the field of flotation include Brenda Mines (Edwards, 1992), Mt Isa Mines Ltd (Lacouture et al, 1991), Outokumpu (Karhu, 1989) and Kidd Creek (Burrows et al., 1989).Expert systems are defined as ""computer systems that apply reasoning methodologies on knowledge in a specific domain in order to render advice or recommendations much like a human expert"" (Turban, 1988). The main areas of application are diagnosis, training, process monitoring and control, and design. There are basically two main types of expert systems: Consultative systems, which are off-line applications in diagnosis and design, and on-line realtime systems, used for supervisory process control and real-time advising."

Jan 1, 1993

By T. ?kre, O. M. Dotterud, S. Haarberg, J. Thonstad, G. M. Haarberg

An electrowinning pilot plant has been constructed at Falconbridge Nikkelverk A/S, Kristiansand, Norway. The equipment consists of a mixing tank where the electrolyte composition and temperature are controlled, an electrowinning tank equipped with five cathodes and six anodes of commercial size and design and a dechlorination facility. Electrowinning experiments were carried out in this pilot plant using acid cobalt chloride solution from the cobalt tankhouse. Key parameters were varied to obtain an improved understanding of the cobalt electrowinning process, focusing on the detrimental deposition of cobalt oxide on dimensionally stable anodes. The extent of anode scaling was found to be dependent on the electrowinning conditions. Low pH, temperature and cobalt concentration resulted in less scale being formed, however at the expense of cobalt current efficiency and cell voltage, adversely affecting electrowinning production capacity and energy consumption. When operating at high acidity, pH in the anolyte was higher than in the catholyte, which is believed to be due to H+ ions taking part in the current transport across the diaphragm, migrating out of the bags surrounding each anode.

Jan 1, 2005

By W. J. D. Stone

Discussions with people knowledgeable in the insulating material field revealed that materials on the market would be considerably improved if there was a greater meeting of certain very desirable criteria. Such criteria include: (1) the material should not burn, even at higher temperatures; (2) at an elevated temperature, the material should not give off toxic gases or produce smoke; (3) the material should have a low energy input; and (4) vermin would find the material unattractive. Theoretical discussions led to the conclusion that an insulating material made by foaming a mineral, preferably of a platy nature, with an inorganic binding system that could be converted to a rigid structure at low temperature would likely meet all the above requirements. It was also theorized that the use of microwaves in the converting stage would be beneficial in the creation of a cellular structure by aiding the foamer through creating vacules of steam. Talc was selected as readily meeting the theoretical mineral requirement and the material of Baker Talc Limited was used as the basic filler. The early results obtained led to an agreement between Americ Mines Limited and Baker Talc Limited pertaining to commercial production in a specific geographic area. It was recognized that due to the economics of shipping, the availability of the basic filler material should be geographically widely spread. Samples of materials were requested and many received from all over North America and one from Britain. Enough work has been done to show that they respond to the basic process in a similar manner as the Baker Talc material. From the data acquired, it is considered that the process is applicable for the production of loose fill insulation, moulded insulation for pipes and structural steel, ceiling tile, batts, sheet and for incorporation into other products such as various roofing board materials. Sufficient development has been done to enable a budget to be prepared for the construction and operation of a loose fill insulation plant.

Jan 1, 1979

By T. Stergiou

An extensive research is being carried out on the shaft furnace operation in order to minimize down-times and reduce operational cost. The need to increase the scrap percentage on the charging mix, together with the need of cheaper spare parts has led to the investigation of alternative materials for the burner system on the shaft furnace. This system consists of a burner block and a flame holder. Traditionally these items are constructed either from SiC ? oxide bonded or SiC-nitride bonded. A lot of problems have been confronted over the past 8 years of operation. Usually, large cracks are formed on both flame holders and burner blocks. This resulted in leakage of combustion gases to the back of the lining and a quick erosion of it. Additionally, the burner blocks suffer from chemical erosion, due to the increased amount of scrap used in the charging mix and the presence of slag inside the furnace. Alternative materials such as stainless steel for the flame holder and alumina-chromia refractory for the burner block have been tested in terms of life-time and resistance on chemical erosion. Furthermore, additional changes have been made on the burner block design in order to alter the flame shape and improve the scrap melting operation.

Jan 1, 2007

By John Keay, Douglas R. Shaw, Gregory J. Olson

"The results are presented herein of on-going laboratory investigations of heap bacterial oxidation as a pretreatment method for the recovery of sulfide-encapsulated gold from ore samples of the Rhodes Mining Lahoca deposit, located in northern Hungary. The ore contains just over 2 g Ault and as much as 6% sulfide, mostly as pyrite. Laboratory aerated column tests conducted at Colorado Minerals Research Institute (CMRI) showed that mild to moderate biooxidation of the finely crushed ore occurred rapidly in approximately three months, with cyanide gold recoveries of up to approximately 60%. The results contrast cyanide gold recoveries of less than 30% from non-pretreated ore. Mineralogical examination of biooxidized residues indicated that the mechanism of biooxidation of crushed ore was related to microorganisms following pathways along structural anomalies in the pyrite grains. Such selective biooxidation is an important result to minimize the biooxidation and aeration time and effluent neutralization costs in a commercial operation.IntroductionThis paper describes the development of a heap biooxidation process for the Lahoca gold project The Lahoca deposit is situated in northern Hungary, at the site of a former copper mining area. Lahoca is a large tonnage, relatively shallow, deposit amenable to open-pit mining Lahoca has the potential to produce I 00,000 ounces of gold annually for at least ten years at its minimum reserve base.The laboratory test work conducted initially by Rhodes Mining NL demonstrated that the Lahoca refractory ore is amenable to whole ore and concentrate oxidative pretreatment and cyanidation. Capital and operating costs, however, for such milled ore treatments were considered relatively high. Rhodes Mining subsequently evaluated heap leaching methods, particularly heap biooxidation pretreatment, as a process route that promised superior economics suitable for exploiting lower gold grade refractory ores.This paper focuses on the laboratory column (simulated-heap) biooxidation test work, particularly the proposed mechanism of selective microbial oxidation, wherein only a small amount of the sulfides are oxidized sufficient to allow commercially acceptable gold recoveries by conventional cyanide heap leaching. Selective or minimal biooxidation of sulfides is considered important to minimize biooxidation time and aeration requirements, as well as acid effluent neutralization costs."

Jan 1, 1998

By S. Burling

Australia has a number of uranium deposits, but they vary significantly in their mineralogy, grade and textural characteristics. Therefore, information from traditional (or conventional) sources regarding the fundamentals of leaching the uranium and gangue minerals is not always applicable when studying particular ores. Empirical studies on particular ores can be effective in understanding leach systems and can lead to improvements in process design, but there remains a lack of fundamental understanding which is necessary for ongoing process optimisation as ore bodies continue to vary. ANSTO Minerals has undertaken a program of work to address some of the fundamental questions of uranium leaching, including the unexpected impact for some ore types of leaching at high oxidation potential.

Aug 1, 2010

By Derek Harvey

"The paper briefly describes the development of the Eickhoff ESA60 roadcutter which is based on the old and well used principles of the shearer loader. It is intended to show that the machine offers a viable alternative to the normal methods used for driving roadways and also for coal production . References are made to installations currently operating in Europe with applications ranging from roadway drivage to pillar recovery. The paper also looks at possible applications in Canada.IntroductionThis paper is an attempt to show how the principles used in mechanical cutting, conveying and roof support are being applied to a development system capable of catering to a variety of situations and conditions. It is also intended to illustrate how the same system can be used as a total mining system for the mining of many minerals.In order to give some sort of time perspective to the age of the principles, reference can be made to an article in Coal Mining & Processing which states:- During World War II the Germans developed the "" panzer"" or armoured face conveyor.- After the war the English developed power cutters or trepanners that were mounted on the face conveyor, this then developed into the shearer.- The first shearer was produced by the Anderson Company in England in 1950 and shortly after that the Eickhoff Company started manufacturing shearers in German y.- The first hydraulic roof support was produced in 1954 by Gullick.This is a potted history of the three major components of the new system, i.e.:- Mechanical cutting element based on the shearer.- Transport element based on the panzer.- Optional roof support based on the hydraulic face supports.It can therefore be said that since the "" youngest"" of the elements was produced in 1954 the principles of the system in respect of the rapid change in mining equipment are in fact old.Of the three major components the most important is the cutting element since the major benefits of the system are to be obtained from this."

Jan 1, 1985

By Ian Rozier

"Emphasis in recent years in western Canada has been placed on the development of large open-pit coal mines, the most notable developments being in northeast British Columbia. However, vast resources exist below the limit of economic open-pit mining, and with world demand predictions of the late seventies in mind, the potential of underground coal mining in western Canada has been investigated. Particular emphasis has been placed on the Plains coalfield of Alberta, and there is optimism that underground coal mines will be developed in the Lethbridge area of southern Alberta.With no existing operations in southern Alberta with which to compare mining conditions, any mine planning and feasibility level studies rely heavily on the engineering/geotechnical data obtained from surface investigation to predict ground control problems and technical constraints on mining. Such investigations have been integrated with exploration drilling programs. Emphasis has been placed on extracting maximum information to provide an over-all appreciation of potential ground conditions and to identify specific ground control problems that could be encountered.The acquired geotechnical parameters are then used to evaluate the mine properties from an engineering standpoint for input into the determination of optimum mine layouts, development directions, mining methods and roadway and face support requirements. These geotechnical studies have been primarily directed toward the longwall mining method, but the acquired data base could equally be applied to alternative mining methods.In addition to the lithologic and structural controls which relate to roof stability, caving characteristics, floor heave and subsidence, investigations have been directed at gaining an understanding of the over-all surface and ground water regime with respect to potential inflow into the mine openings and ground control problems that could be caused by inflows encountered during mining. Experience has shown that soft floor conditions and water control are important factors to be considered in a longwall layout, and without doubt these parameters will play a major role in the design and operation of a successful longwall operation in the Lethbridge coalfield."

Jan 1, 1986

By Virginia Lawson, Adam Price

The rougher flotation stage is used to reject liberated gangue at a coarse size. Base and precious metals due to their high specific gravity tend to recycle in the grinding circuit and report to the flotation circuit at a finer size than the gangue from which it is being separated. Generally liberation levels of greater than 50% are achieved in roughing and thus a portion of the feed can be immediately upgraded to final concentrate. The proportion increasing as the amount of liberated mineral in the feed increases. Scalping out concentrate from the rougher can reduce the size of the subsequent regrind and cleaner circuits. Examples of alternative process design for circuits demonstrates that you don’t need large volumes to effectively recover all of the minerals – you need smart flotation. Several case studies will be presented where circuits can be significantly reduced in size by designing smarter – not larger. This paper describes case studies to test the amenability of the Jameson Cell to produce final concentrate from rougher feed. Metallurgical performance and plant design implications are discussed. Froth flotation has been used extensively for mineral concentration for over 100 years. Although the flotation cell design has changed, it has generally simply increased in capacity rather than increase in efficiency. Cell capacities of over 600 m3 are now being used in rougher flotation particularly for the lower grade ores where the amount of surface area for flotation is deemed less significant than the required volume. The plant design volume in rougher flotation comes from laboratory batch flotation tests and/or pilot plants. The volume required for the plant is calculated based on the laboratory residence time multiplied by a scale- up factor. Examples of laboratory to plant scale-up design are given in Dunne et al. (2010 part 2). The factors are usually between 2 and 3. A laboratory residence time of 10 minutes would equate to a plant design residence time of 25 minutes using a 2.5 factor. The volume of the required flotation cells can then be calculated using the design tonnage and volumetric throughput. This scale-up factor takes into account the differences in performance between batch flotation efficiency and full scale plant. The differences are likely related to inefficiencies of bubble particle contact in large cells as well as froth recovery, which is essentially complete in a batch cell. Flotation cells, such as the Jameson Cells, are smarter designs that improve bubble/particle collection, bubble/pulp separation efficiency and operate with high froth recovery rather than simply getting bigger. The Jameson Cell was designed on the principal of improving the collection efficiency of fine particles by separating the contact zone from the separation zone and having the bubbles generated by the plunging jet shearing and entraining air. This means the method of bubble generation is not impacted by the wear of mechanical equipment as it the case in other flotation devices. Jameson Cells make bubbles less than 600 micron in size under most operating conditions (Ding, 2016).

Jan 1, 2019