Search Documents

WHAT IF? ?Mine closure and reclamation liabilities were fully funded -at all times from current mine revenues ?Unexpected & catastrophic events were insured ?Remediation costs could be capped ?Risk management was improved ?best practice and independent oversight ?Host communities?concerns were adequately addressed If this could be achieved within a cost-effective financial structure, this may be a solution to a complex issue for the mining industry

May 1, 2006

By Giles St. Pierre

"The purpose of this paper is to report in a general way on the use of the Portaspec X Ray Spectrograph.At Manitou Barvue, we are milling two types of ores, copper and zinc. The control assay practice was to take grab samples at 4 hour intervals. These samples were dried in the mill, then taken over to the Assay Office where two operators would process them. Three hours later results were available at almost the same time as the operator was ready to take his set of grabs again, leaving no time for adjustments, if any were needed.After a reduction of personnel, there were no assays available on night shift. This practice was slow and inadequate, and a new way of doing control assays was investigated.After investigation the Portaspec was found suitable for the type of operation that we had in mind. The Portaspec is a conventional dispersive type of X Ray spectrograph. The instrument consists of three parts:The Power Supply The Spectrographic Head The Digital ScalerIn our case, where dried powder samples are analyzed, the instrument was provided with a two sample holder using one for the standard and the other for the sample. The operation of the instrment does not require any degree of skill or knowledge of chemistry or spectrography.Previous to buying the instrument, six sets of six to ten samples were sent to the supplier along with the assay for each sample. These samples were Cu. HDS., Cu. Conc., Cu. tls, - Zn. HDS., Zn. Conc., Zn. tls. A definite pattern was observed. For example - six Cu. HDS. samples ranging from .40 to .90 gave 10400 counts for the lowest to 16.040 counts for the highest. The number of counts were then plotted to give percentages."

Jan 1, 1971

By The Staff

"SummaryDetermination of uranium in ores may be made by measurement of their radioactivity.The method most commonly used is that of measuring beta radiations with the tray-type beta counter. This will give an accurate uranium determination provided the sample does not contain thurium and that the beta and gamma activities have not been disturbed from their natural state of equilibrium. Such a loss of equilibrium will result from mining the ore or from the weathering of the surface rock.A method is described which eliminates errors due to loss of equilibrium. The beta and gamma activities are measured simultaneously in one simple operation. This method is recommended for assaying samples of products from milling operations and its use is limited only by the presence of thorium in a ratio greater than one part of thorium to twenty parts of uranium.A third method is recommended for the analysis of exploration samples and diamond drill cores, which may be assayed in the uncrushed state.Rapid determinations of a large number of samples is possible with the pressure ionization chamber, which is sensitive to gamma activity."

Jan 1, 1950

By B. D. Thompson

Many mines adopt necessarily conservative backfilling strategies due to a lack of understanding of their backfill behaviour. In the past five years, extensive instrumentation campaigns have focused on measuring in-situ cemented paste backfill behaviour. These tests have resulted in optimised backfilling efficiency through elimination or reduction of cure periods where; i) controls on backfill behaviour are understood, and ii) barricade pressures are demonstrated to be within a safe range using routine monitoring as a required QA/QC procedure. Recently, this work has been extended to consider hydraulic backfill operations. Two stopes have been instrumented at Vale?s Coleman and Garson Ramp mines. The instrumentation and deployment methods are discussed, and representative total earth pressure, pore pressure, and temperature data are presented. In one case, pressures in the stope are relatively low as drainage causes strength gain in the fill and so pressures are arched. In a second example, again, drainage causes strength gain in the fill, but increasing temperatures correlate with pressure increases even during downtimes in filling. These pressure increases are thought to be caused by thermal expansion of the backfill in confined locations. Generally, the instrumentation approach has proven successful in measuring hydraulic backfill behaviour and offers good potential for incorporation into a procedure to safely maximise backfilling efficiency through routine barricade pressure monitoring, when combined with safeguards to ensure adequate fill drainage.

Aug 1, 2013

By Bradford P. Simser

Increasingly sophisticated rock mechanic tools are becoming more and more available for today?s ground control specialist. However many problems are still beyond our ability to explicitly calculate or measure. There is often a gap between the ?art? and the ?science? of rock mechanics. This paper focuses more on the ?art?, giving relatively simple examples of underground observations and micro-seismic records to help explain ground control issues. Ground support techniques such as in cycle shotcrete with high pressure water scaling, mesh and bolting, pumpable resin bolts/cablebolting, and yielding bolts with load spreading straps are discussed. The use of primary/secondary type blasthole sequences in moderate to high stress situations is also discussed with several examples of the micro-seismic response to the stoping. Relatively erratic geology with high material strength contrasts is currently being mined with blasthole methods at Nickel Rim South. Although the mine is still in its? ?early? days, over 1 million tonnes has been extracted and some empirical experience is highlighted with potential longer term issues also being discussed.

Oct 1, 2010

By Maria D. Mastalerz, Wei Wang, Maria E. Holuszko, Amit Kumar

In this study, the micro-FTIR analysis was used to investigate in-situ surface properties of coal and its components (macerals) and these were directly correlated to the coal hydrophobicity as measured by the contact angle before and after reagent addition to understand the suitability of the reagent for flotation. The micro-FTIR technique can provide a semi-quantitative analysis of the chemical functional groups on coal surface, exactly where the contact angle is being measured. Selected functional groups and their ratios that provide information about aromaticity, the contribution of oxygenated groups, and aliphaticity are used to evaluate the reactivity between reagents and various coal components. The observations made in relation to the susceptibility of some reagents towards certain coal components should lead the way to a smarter way of using process design in terms of reagents selection for coal flotation.

Jan 1, 2017

By Y. H. Hatzor, D. Bakun Mazor

"A new model for thermally-induced block displacement in discontinuous rock slopes is being explored inside a Controlled Climate Laboratory (CCL). The model is based on a hypothesized wedging mechanism that takes place inside the filled tension crack of a discrete block that rests on an inclined plane. Irreversible block sliding is assumed to develop in response to climatic thermal fluctuations and consequent contraction and expansion of the sliding block material. While an analytical expression for this model is already available, we are exploring the possibility of obtaining such a permanent, thermallyinduced, rock block displacement, under fully controlled conditions in the laboratory, to enable effective analysis of the sensitivity of the mechanism to geometry, mechanical properties, and temperature fluctuations.A large scale (approximately 0.5 m3 in volume) model consisting of four blocks has been installed in the CCL. The CCL permits accurate control of atmospheric temperature (?0.5 °C) from 6 °C to 45 °C. Harmonic temperature function is planned in advance and is controlled by a computer program throughout the experiment process. The minimum length of the temperature cyclic period for thermally-induced block displacement is calculated here based on the existing analytical model.Due to the fact that this experiment is still in progress, preliminary results will be available in the next few months. The obtained results may explain sudden triggering of rock slope failures that are not correlated with common failure triggers such as seismic activities, pore pressure build-up, or freezing and thawing of water inside rock joints."

Jan 1, 2015

By J. Chao, C. Tan, N. Stubina

"Since J978, Falconbridge Limited has operated two electric furnaces at its nickel-copper smelter in Sudbury. As part of its S02 Abatement Program, the smelter has undergone many changes over the last seven years.This paper describes the impact of these changes on the operation of the furnaces. Some of the topics to be covered include: the installation of sidewall copper coolers; current operating conditions; and furnace heat and mass balances. HistoricalFalconbridge began smelting ores in the Sudbury area in 1930. The original smelter consisted of a 1.3 m by 3 m blast furnace and two 4 m by 6 m converters. The blast furnace was supplied with untreated mine are and molten slag/matte was discharged into a round settler.In 1933 the smelter began treating flotation concentrates. The concentrates were mixed with fine magnetic ore and flue dust, then sintered on down-draught Dwight Lloyd machines. This provided an agglomerate suitable for furnace burden which was charged to the blast furnace while still hot.Between 1930 and 1954 nickel production was increased by lengthening the 3 m furnace to 4.6 m, then to 6 m, and later by constructing additional furnaces. By 1958, the plant consisted of one 7.5 m blast furnace, a settler, and three 4 m by 9 m converters."

Jan 1, 1994

By Xu Feng, Han Shufeng, Zhu Bin, Wang Mingming

Due to urban subway tunnels mostly built in the cities with highly density buildings, the geological and construction conditions is complex, especially certain sections of the subway tunnel will pass through from the foundation of the overpass, therefore the stability and surface deformation control of that section’s tunnel excavation is particularly important. Taking Xi'an Metro Line Three interval tunnel as a research object, we have used FLAC3D simulation to analyze the tunnel’s surrounding soil deformation and tunnel lining stress distribution under bridge foundation with shallow buried covered excavation method. Analysis results show: (1) After the excavation of the tunnel right line, due to the bias of the upper bridge foundation the right of the tunnel showed relatively large deformation. In order to ensure the construction safety, we recommended using the grouting anchor reinforcement on the right side wall to further control the deformation zone. (2) The maximum vertical displacement of the ground occurred in the right wall of the tunnel portion which was due to the intensity of soil outside the grouting range of the arch is low, as a result the deformation is larger; this position requires special attention, strengthening the monitoring measurements of this part is necessary to avoid the large deformation and other adverse effects of the upper portion of bridge foundation. (3) The maximum vertical force area of the initial lining of the tunnel is in the middle of the side wall, while the second lining in this part of forces is smaller, thus at the beginning of the construction of the liner, attention should be paid to this area. On-site grouting or steel bracing reinforce support may be used if necessary.

Jan 1, 2015

By Trevor McGiddy

"Australia's prosperity relies significantly on income generated from exports of resources and agricultural products. In 1989-1990, coal was Australia's most valuable export commodity, contributing. A $5.7 billion or 14% of all export income.The abundance and quality of its coal resources and the proximity of Australia to the rapidly developing economies of Southeast Asia were significant factors that encouraged export-oriented growth and investment and will continue to do so. On the other hand, the 1980shighlighted the sensitivity of the industry to international changes in supply and demand, currency and socio-political forces.Following many years of disappointing returns for investors, mainly as a result of falling Australian dollar coal prices, resolve will be necessary to maintain competitiveness with resource-rich nations. In recent years, operators, unions and governments have begun to embark on a long overdue rationalization of domestic issues in a bid to increase productivity and reduce costs.The nature of mining operations is also changing; deeper surface mines and the growth of longwall mining will require the development of new technology and skills. Other challenges emerging from the international environmental debate will require that Australia responds appropriately to demands for cleaner fuels, energy efficiency and environmental responsibility.The future development of the Australian coal industry will therefore be influenced by its own ability to become more efficient and mature in the production of quality coal products and through rational international response to environmental questions."

Jan 1, 1992

By W. L. Strand, D. N. Madge

"Experimental and pilot operations in bituminous sand processing require due care and attention in the design and analysis of measurement programs. This paper deals with a case study in experimental design and data analysis for a series of experimental campaigns that have been conducted over the past five years by Kilborn Western Inc., acting on behalf of Bitmin Resources. Beginning with the design of the experiment and following into the use of linear and nonlinear regression models, the phenomenology of bitumen extraction is illustrated. The final testing program tested 13 oil sand types as well as a wide range of process variables for all the unit operations of the complete process.The program was successful in developing process fundamentals and scale-up criteria. Several phenomenological models were proposed and tested. Their range of applicability was explored. This paper illustrates the range of applicability of these models and discusses the development of alternative models.IntroductionOver the past five years Kilborn has conducted a series of bench scale and pilot scale experiments designed to explore the phenomenolgy of a new concept in medium temperature processing of bituminous ores. These experiments at feed rates ranging from .1 to 24 t/h were conducted on water wet sands from the .Athabasca region near Fort McMurray. They were based on experimental designs chosen to provide a systematic means of identifying the response surfaces of the process over a range of conceptual designs. The following diagram shows the experimental arrangement:"

Jan 1, 1998

By D. J. Lucifora

Monitoring-While-Drilling (MWD) is a proven technique that records instantaneous on-drill parameters which can be used to supply contextual information for in-situ, down hole conditions, such as: changes in geology, the presence of pre-existing fractures and dynamic alterations, down hole conditions including bit bailing, bit blockages and bit wear, and improper drill operation. This technique has been widely used in the oil and gas industry and, eventually, it was transferred to the mining industry. A challenge when analyzing and interpreting MWD data is in utilizing proper filtering which enables one to properly eliminate any ?noise? from the signals of interest. Overall the importance of MWD data is that, through the collection of operational field-based data, a dataset can be acquired which allows experimentation and analysis to be carried out. Such a dataset is often impossible to replicate in a laboratory setting. If successful, and through iterative refinement, any promising method can eventually be implemented on-machine and using real-time monitoring techniques. This paper will provide a state of the art review of presently used MWD techniques and applications in industry. The paper?s primary focus will be on shallow, mining-style, blast hole drilling but will also take into account techniques and applications utilized in oil and gas drilling which have not been adopted in the mining industry. In the cases where MWD techniques and applications exist solely in oil and gas drilling the paper will examine and comment on the potential utility of technology transfer to mining applications.

Aug 1, 2013

By Stuart J. Schofield

Introduction The study of the ore deposits of British Columbia is one of fascinating interest not only from a scientific but also from a commercial standpoint and certain wide problems in connection therewith have interested me for some years. Several of these problems have been set forth in papers presented before this Institute on previous occasions. In 1918 it was pointed out that the commercial ore deposits of British Columbia, with one exception, were associated with the granodiorite batholiths of upper Jurassic age. This was followed, in 1922, by a discussion of the ore deposits of British Columbia in which the mineral belts of the province were defined and named, showing a zonal arrangement of ores in which the Pacific coast deposits are characterized by the presence of copper, while the interior belt is marked by the presence of silver, lead, and gold. Methods Of Investigation In reading various reports on the economic geology of British Columbia one is struck with the fact that the mineral veins may be arranged as a system and further examination will show that such a system follows two main directions, one northeasterly and the other northwesterly, both related in origin to the same force.

Jan 1, 1925

By P. M. Chapman

Risks to aquatic receiving environments from uranium mining and milling fall into three categories: physical (habitat change), chemical (e.g., uranium, selenium, total dissolved solids [TDS], metals including vanadium), and radiological. Although all categories of risk need to be managed, chemical risks are the most significant and are typically chronic rather than acute. For instance, selenium toxicity is primarily manifested as reproductive impairment due to maternal transfer, resulting in embryotoxicity and teratogenicity in egg-laying vertebrates. Risk is best assessed using a weight of evidence approach focused on ecosystem services. Risk management should be based on both risk assessment and adaptive monitoring.

Aug 1, 2010

By A. Jeffkins

Visibility is restricted when operating load haul dump vehicles resulting in a number of serious accidents in the Ontario Mining Industry. One of the leading causes of these accidents is the inability of the equipment operator to see clearly people, objects or hazards around the machine. Previous line of sight testing by the research team found specific machine characteristics were responsible for blind spots and impaired visibility. In order to identify feasible design modifications a computer simulation program, Classic JACK 3.1, was utilized. Program features include human factors analysis, which allows evaluation of line of sight and operator posture in order to decrease risk of musculoskeletal injury. Research within the virtual computer environment consisted of a Visibility Audit and a Target Audit in order to quantitatively determine how certain components of the LHD design affected the line of sight around the vehicle. Results indicate that modifying the LHD light brackets, engine profile, cab posts and other components will enhance visibility. The addition of cameras located on the front and rear of the vehicle were able to enhance the operator?s sight lines to previously obstructed areas. Modifications to seat height and the operators orientation both improved sightlines and decreased risk factors associated with back and neck musculoskeletal disorders.

May 1, 2003

By Robert D. Brown

The federal government kicked off the new budget season in November 1978, when Finance Minister Chretien announced a handful of proposed amendments to provisions of the federal Income Tax Act and Regulations affecting mining. (See Tax Notes in the January 1979 issue of the CIM Bulletin.) Declaring in his budget speech that these changes were in response to the report of the joint federal/provincial task force on resource taxation, Mr. Chretien tossed the ball to the provinces-" I want to take the lead here... I feel confident that the provinces will do their part". Quebec and Ontario, picking up the ball in their spring budgets, have announced favourable modifications to the provincial taxes on mining, with these moves being paralleled in the recent Manitoba budget, which proposes a flatrate mining tax to replace the previous controversial two-tier royalty. In the meantime, the federal government passed a host of amendments to the federal earned depletion regulations. The result is yet another batch of complex tax changes for the industry to note and digest, but this time with the hopeful factor that most of the changes are favourable to the industry. This article reviews the current status of the federal budget changes, comments on the Ontario, Quebec and Manitoba proposals, and reports on the changes to the earned depletion regulations that were passed by Order-in Council in March 1979.

Jan 1, 1979

By S. Eckert, M. Reuter, D. Obiso, S. Kriebitzsch, M. Akashi

The present paper focuses the application of CFD techniques to investigate the Top-Submerged- Lance (TSL) gas injection in liquid metal. Previous works of the authors have shown that up- and down- scaling procedures based on the modified Froude number have some shortcomings, as this approach does not take into account the interfacial and viscous forces. Indeed, surface tension and dynamic viscosity of the smelting slags (σ = 0.4-0.5 N/m, μ = 0.2 Pa·s) are higher than the operating fluids that have been used in literature (water, paraffin oil) to study TSL injection in down-scaled furnaces. In order to get closer to real systems, the authors study the TSL injection of Argon in a liquid metal. An experimental campaign was carried out in the X-ray lab at Helmholtz-Zentrum Dresden-Rossendorf (HZDR), where the eutectic alloy GaInSn was used as liquid phase. The alloy is liquid at room temperature, and X-Ray imaging is used to picture the multiphase flow in a quasi-2D vessel. The aim of the present work is to demonstrate the applicability of CFD techniques to model multiphase flows involving liquid metals, and validate the model using the data produced at HZDR. The commercial software ANSYS Fluent® was used together with the Volume of Fluid model to directly resolve the gas-liquid interphase. Some features of the flow, such as the void fraction distribution and bubble detachment frequency are tracked with CFD and compared to the experimental data. INTRODUCTION In the last thirty years the TSL smelting technology has increasingly been used for industrial non- ferrous smelting processes and is now one of the significant pyrometallurgical processes. Developed in the early 1970’s at CSIRO, the furnace is nowadays commercialized in different market sectors, including copper and lead smelting, zinc fuming, waste treatment and slag recovery (Floyd, 2005). Despite the wide application of these reactors in the pyrometallurgical market, some aspects of the process are still not fully clarified, since in-situ measurements and optical accesses are prohibitive because of the high temperatures and aggressive conditions. Phenomena such as the bubbling regime, the slag solidification and the submerged combustion still need a deeper scientific investigation to obtain a better understanding of the process.

Jan 1, 2019

By D. B. Nazzer

"ANY DISCUSSION of energy today is incomplete without consideration of nuclear energy. In the Maritimes, with plentiful supplies of coal, with relatively easy availabilty of imported oil brought in to the deepwater terminals, with future sources of large supplies of oil and gas anticipated from under our neighbouring continental shelf, and with the Fundy tides, you may question why nuclear energy should be considered. What follows may not give you a specific answer to that question, but it may provide a basis for better understanding. Energy from the sun, from hydraulic sources and from combustion has been available to man from prehistoric times, for thousands of years, but the most sophisticated source of energy, the actual conversion of matter into energy by man, has been developed entirely within the last one-third century, since the discovery of fission in 1939, and the application to generation of electric power has all been done within a generation or less. The pressure of military needs during and after the second world war was largely responsible for the speed of initial development, by funding and focussing the effort needed to develop the basic technology, and in particular materials. The U.S. defence program yielded, for example, the large-scale isotope separation processes for fissile U'35 and for heavy water. The nuclear submarine program yielded zircaloy, a key structural material for the core of the Canadian Candu type reactor."

Jan 1, 1972

By Alan R. Holt

"This paper provides an overview of the use of uranium and coal in Ontario Hydro's generation program. The dynamics of available supply sources including mining and transportation infrastructures and regional considerations are described. Included is a discussion of needed procurement strategies, both in place and planned, to meet fluctuating fuel requirements while ensuring adequate supply security and cost effectiveness. IntroductionDuring the first half of this century, Ontario Hydro or the Hydro Electric Power Commission of Ontario, as it was then known substantially supplied all of the province's electricity needs from a large number of hydraulic generating stations. Although hydraulic power still provides a very significant part of Ontario energy requirements, this paper will concentrate on the role of uranium and coal in their generation program. To provide a perspective on the importance of these two fuels, Figure I shows the approximate value of each for the past few years in relation to Hydro's total operating costs. The trend toward increasing nuclear output and a corresponding decline in coal use is also clearly illustrated.Figure 2 shows the currently installed capacity of their three main energy sources, hydraulic, nuclear and coal and the 1986 production totals for each, followed by Table I which compares the average operating or running cost on the basis of dollars per megawatt hour for each type of plant. It demonstrates dramatically why Ontario Hydro base load s its hydraulic and nuclear plants, and why coal has become the swing fuel on the system. Although they have a 1200 megawatt plant in Toronto with natural gas-burning capability, and a 2000 megawatt oil-fired station near Kingston, both are presently mothballed and have not been considered in this paper.This paper starts with a user's perspective of the nuclear fuel supply situation which will be discussed in relation to the usual considerations of security, flexibility and cost."

Jan 1, 1988

By A. Probst, J. A. Finch

"Solids concentration (% solids) profiles and the clear liquid/slurry interface level (mudline) were determined from conductivity measurements in thickeners at Falconbridge' s Strathcona mill (Ni concentrate and non-mag thickeners) and Kidd Creek Division (Cu, Zn concentrates and final tails in the concentrator and thickeners in the Zn plant).The conductivity measurement system consisted of a probe 1.5 m in length with 24 electrode cells, a 24-channel relay, a conductivity meter and a computer. A conductivity profile is collected which locates the mud-line by the sharp change in conductivity. The conductivity measurements are readily converted to solids concentration profiles without need for calibration.The results from the conductivity measurements were compared with those from pressure profiles and direct measurements on local samples obtained using a modified Noranda sampler.It is concluded that the conductivity technique is applicable to locate the mud-line and to estimate the solids concentration profiles in thickeners. This on-line information could improve the operational efficiency of industrial thickeners.INTRODUCTIONAn automated, on-line technique for detecting the clear liquid/slurry interface (or mudline) and the variation in solids concentration with depth would enhance thickener operation and control. In some processes such enhanced control offers significant benefits. For example, in hydrometallurgical operations solid/liquid separation is often the process limiting step. Water treatment plants are increasingly expected to operate remotely and reliable sensing is vital.Current attempts to detect the mud-line include reflection of some signal (e.g. sonar), floats (Dahlstrom, 1985) and measurement of pressure (Rosenblum, 1991), and in one case, natural radioactivity of the solids (Johnston and Simic, 1991). A recent commercial development uses reflection from a vertical array of optical transmitters/sensors, which also gives local solids concentration (BTG Inc., 1991)."

Jan 1, 1993