Search Documents

By C. B. Ndimande, C. Ntsele, M. Lisso, L. Arlow

"In the processing of UG2 platinum ore, stirred milling technologies are dominating regrind applications that require grinding the particles to P80s’ in the region of 45 µm. For this application stirred mills are 30–40% more energy efficient and require a smaller foot print compared to traditional tumbling mills. In this work a study was carried out using a batch pin mill and three scales of Stirred Media Detritors. A laboratory scale pin mill, a pilot scale Stirred Media Detritor with an installed power of 18.5 KW and two industrial scale Stirred Media Detritors in continuous operation, with an installed power of 355 KW and 1,100 KW were used. The industrial scale SMDs were in the secondary grinding section of a mill floatmill float (MF2) UG2 processing plants. The tests were focused on assessing the effect of feed rate and percent solids on power consumption and product fineness at lab scale, floatation response of the SMD product at pilot scale and on an industrial scale, the effect of feed rate on energy consumption and product fineness. The measurements obtained were feed flow rates, mill power and from the samples cut, particle size distribution of both feed and product. Specific energy was observed to increase with increasing percent solids over the 30wt% to 80wt% studied. Floatation response tests of the pilot scale SMD products show improvement in grade. Specific energy and reduction rations are observed to decrease with an increase in feed rate.INTRODUCTIONThe purpose of comminution in most mineral processing applications is to liberate the valuable minerals from gangue so that they can be recovered in subsequent separation stages. Most precious and base metal plants treat low grade fine-grained ores which require a higher degree of size reduction to yield the necessary degree of liberation (Partyka & Yan, 2007). Many authors have shown that the relationship between product size and grinding energy consumption is exponential, the finer the product from the comminution device, the higher the energy consumption (Gao & Weller 1993; Napier-Munn, Morell, Morrison & Kojovic, 1996; Jankovic, Valery & La Rosa, 2003). The suggested reason for this kind of relationship is that smaller particles have fewer flaws and higher strength than larger particles. Particles with fewer flaws and higher strength require higher energy for breakage to occur. One of the challenges most plants face is that of efficient energy utilisation in the liberation of the mineral from these complex ores. Conventional tumbling mills are not energy efficient in fine and ultra-fine grinding applications because some of the energy is spent on moving the charge and does not go directly into breakage. Stirred mills have been found to be about 30% to 40% more efficient and require a smaller foot print compared to traditional tumbling mills for regrind applications that require product size with P80s’ in the sub 45 µm regions (Radziszewski & Allen, 2013). Stirred mills are able to produce fine product because they can achieve a high number of stress events per unit time and volume compared to tumbling mills (Kwade, 1999a). To minimise energy usage without compromising product quality, the mining industry has adopted stirred milling technologies for fine and ultra-fine grinding (Radziszewski & Allen 2014; Kwade, 1999b). The south Africa platinum group metal (PGM) industry alone had over 40 stirred media mills installed by 2011 (Rule, 2011). Of that 40, 13 were in the ultra-fine grinding (UFG) application and the rest in main stream inert grinding (MIG)."

Jan 1, 2016

By J. D. Jones

The geographic occurrence of economic mineral deposits presents a variety of problems in modern tailings disposal operations. This paper presents case histories in several sectors of the mineral industry as well as the several stages of operations planning required for new designs, system expansion, reactivation of abandoned systems and upgrading to present environmental standards.

Jan 1, 1978

By C. Hu

A MOS capacitor hydrogen sensor array is reported for hydrogen gas distribution mapping. Si(100) was used as substrate for film deposition. After silicon oxide growing on the silicon surface with dry thermal oxidation, palladium film was sputtered on silicon oxide as hydrogen-sensitive gate material in MOS structure. The 3x3 sensor array was patterned on silicon substrate and packaged in one chip. Sensors' response was test with impedance analyzer. The sensors in array were calibrated in the hydrogen concentration range from 10ppm to 10000ppm. The 2D hydrogen concentration distribution was obtained with the calibrated sensor array.

Jan 1, 2005

By A. Desbiens, M. Maldonado, R. del Villar, Aguilera. R.

This work details the application of a multiple model approach to estimate frother concentration in flotation processes. The methodology consists of identifying a set of linear dynamic models representing the effect of gas rate on the collection-zone gas holdup at different known frother concentrations (calibration step). An adaptive law is then obtained using Bayes' rule to evaluate the conditional probability that each model represents the observed system behavior. In this way, a frother concentration estimate is calculated as a weighted sum of model probabilities and their associated (known) frother concentrations. Experimental results conducted in a two-phase system using Dowfroth250C are promising. Modeling and analysis for MIBC frother are also provided.

Jan 1, 2009

By K. Enns, J. J. Byerley

"While thiocyanate (SCN-) is used in a number of industrial processes (production of polyacrylonitrile filaments, synthesis of agricultural chemicals and certain metallurgical solvent extraction and flotation circuits) it is recognized more as an undesirable by-product associated with ' the metallurgical industry. Thiocyanate is present at low concentrations in some waste streams from the iron and steel industry. Of particular significance is the formation of thiocyanate during cyanidation of gold and silver ores, concentrates, tailing s and residues. The thiocyanate levels present in the resulting effluents may range from a few mg/I to several thousand mg/I.At present, thiocyanate does not appear to be as hazardous in the environment as cyanide (CN-) at the same concentration although its interaction with other species and resulting decomposition of products may be unacceptable. Of course the presence of thiocyanate in the leaching circuit and ultimately in the effluent streams may add considerably to the oxidative requirments of any non-selective treatment process for cyanidation wastes.With respect to the thiocyanate as it relates to the cyanidation process, two aspects are evident. Thiocyanate forms and persists in the cyanidation circuit resulting in a ""fouling"" condition with subsequent loss of leaching activity. In order to reduce or control this problem, it is common practice for some mills to discharge daily as much as 20% of the barren leach liquor. Besides contributing to fouling of the leach liquor the formation of thiocyanate represents an irreversible loss of reagent cyanide. It is noteworthy that in some present or proposed mill practice reagent cyanide loss through thiocyanate formation may reach 50%(1). The purpose of this paper is to discus s the application of controlled electrooxidation of thiocyanate with the view of suggesting a process for regenerating cyanide from waste thiocyanate(2). The paper describes the important theoretical aspects and presents experimental data obtained for thiocyanate electrooxidation using both small and large scale electrochemical reactors. Some economic conclusions are presented."

Jan 1, 1984

By M. Maldonado, P. Olivares

"A submersible sensor for real-time gas holdup measurement in the collection zone of industrial flotation machines is introduced. The working principle is based on the generation and measurement of a pulp flow using a gas-exclusion cell immersed in the aerated slurry. The gas exclusion cell consists of a variable-area open vertical tube designed to be filled only with pulp by preventing gas bubbles entrance. The higher density of the fluid column within the cell generates a downward flow of pulp; the rate of this flow is proportional to the gas holdup outside the cell. The gas holdup measurement is achieved by tracking the velocity of the pulp flow leaving the gas-exclusion cell, using a magnetic flowmeter. Construction details of a prototype and its testing in two- and three-phases are discussed.INTRODUCTIONFlotation process optimization consists of finding and maintaining operating conditions that maximize flotation performance measured in terms of recovery and grade. The selective separation of mineral particles proceeds in two interactive zones where different and simultaneous phenomena take place: in the collection zone, the valuable particles are separated by collection on the surface of bubbles, while in the froth zone, the bubble-particle aggregates are gathered, drained to remove entrained particles, and taken into the concentrate stream. The cell overall performance, which can be determined from proper stream sampling, is a function of the recoveries in the individual zones. These zone recoveries cannot be independently measured nor calculated from operating variables. Progress in the assessment of these recoveries has been slow because on-line and reliable sensors to measure properties of the drastically different dispersions existing in both zones are not available.In the case of the collection zone, it has been demonstrated that the recovery of hydrophobic particles on the surface of bubbles, considered as a process with first-order kinetics, correlates with the bubble surface area flux (Finch et al., 2000; Hernandez, et al., 2003; Lopez-Saucedo et al., 2012). Bubble surface area flux (bubble area generated per unit time and cell cross-sectional area), is a variable affected by gas flow rate, bubble size distribution, and frother type and concentration. Gas holdup (volumetric fraction of gas dispersed in the slurry) is also affected by the same variables, and as such, carries information on the interacting variables that define the performance of the process. Therefore, a correlation between gas holdup and bubble surface area flux was expected and demonstrated (Finch et al, 2000), and since gas holdup is easier to measure as no bubble size is required, it has the potential to be the basis of a cell control and optimization strategy if a continuous sensor is available."

Jan 1, 2016

By K. E. Waters, J. E. Nesset, F. Rosenblum, J. A. Finch, S. Moon

"Some materials when exposed to various conditions can exhibit a rise in temperature without requiring an external heat source. Generally referred to as pyrophoric or self-heating substances, they challenge the safety of materials handling, storage and transportation. Reliably assessing the self-heating potential of materials is thus essential. Over the years a number of test protocols have been developed. A widely accepted method is that recommended by the United Nations to certify the safety of shipping pyrophoric goods. Our test work on sulphide materials has shown that the U.N. test can give false negatives if the sample oxidation history is not considered. Depending on the degree of oxidation (“weathering”), the same sulphide material can exhibit self-heating ranging from safe to hazardous. For concentrates, oxidation can occur during storage and transport making the sample weathering history an important consideration in the test work. To make the U.N. test, and other single-stage self-heating procedures, more reliable in assessing self-heating potential when testing sulphide materials, it is suggested that a weathering step be incorporated in the test protocol. This test work for two sulphide samples, an ore and a concentrate, demonstrates the impact of incorporating a weathering stage in the test protocol. INTRODUCTIONSelf-heating occurs when exothermic reactions produce heat faster than can be dissipated to the surroundings. Numerous substances self-heat, ranging from wood chips and powdered milk to coal and sulphide minerals (Beever & Crowhurst, 1989; Hudak, 2002). Mixtures of sulphide minerals, most notably those containing the iron sulphide pyrrhotite (Fe(1-x)S), commonly encountered in the extraction of base metals (e.g., copper, zinc, lead, and nickel), are particularly prone to self-heating (Rosenblum, Nesset, & Spira, 2001; Payant, Rosenblum, Nesset, & Finch, 2012). In the mining and subsequent processing stages, the minerals are progressively liberated and finely ground, then separated, usually by flotation, with the resulting concentrates stored and transported to smelters for metal extraction. At most of these stages the sulphides are exposed to both moisture and oxygen, conditions that promote partial sulphide oxidation and the formation of elemental sulphur. Studies have shown that pyrrhotite, in particular, readily oxidizes to form elemental sulphur (Bernier & Li, 2003; Belzile, Chen, Cai, & Li, 2004; Somot & Finch, 2010). The elemental sulphur becomes fuel for further self-heating as the temperature of the mineral mixture increases above 100 oC (Rosenblum & Spira, 1995; Somot & Finch, 2010). It is believed the propensity of pyrrhotite to self-heat is a result of its iron-deficient, and hence somewhat unstable structure. It is worth noting that pure metal sulphides (with the exception of pyrrhotite) do not exhibit appreciable self-heating. A mixture of minerals sufficiently different in their electrochemical rest potential is required to initiate self-heating at ambient temperatures (Payant et al., 2012)."

Jan 1, 2016

By F. Urekar, R. B. Pankhurst

"Air spaces and air gaps in an explosives column are known to allow greater distribution and cushioning of explosive energy from the rock mass. This energy distribution is enhanced if the explosives ' gases can be confined in the borehole for as long as possible by plugging and stemming above the air space.Power Plug is an inflatable plug which can seal a borehole at any point to separate the stemming from an air gap and explosive toe load.IntroductionThis paper will discussion-going work by C-I -L Inc. and operators of two open pit mines to study the results of using Power Plugs:I. Pit wall stability - the authors have found the Power Plug effective for wall control blasting in open pit mines.2. Selective mining of coal seams - the authors work shows the Power Plug allows mining selective coal seams by predrilling underseam waste wedges.Pit Wall StabilityWall stability in an open pit mine is essential for safety. Good wall stability can be achieved with wall control blasting techniques which cushion the effect s of the explosives charge by decoupling the charges from the borehole wall. The usual method of decoupling a charge in a large-diameter rotary borehole is to load the explosives in tubes (Fig .I) . We now believe the air deck system is effective in sea ling a borehole above the explosive charge to create an air deck within the borehole which will cushion the blast.In a linear decoupled charge, an air annulus surrounds the explosives charge and cushions the effects of detonation genera ted gases on the pit wall. In an air deck, i.e. with the hole plugged at the collar, the gases genera ted by an explosive toe load are sealed in the empty borehole column. After a period of time, these trapped gases produce radial cracking between holes along the entire length of the borehole.It is common practice to employ de coupled explosive charge columns in the borehole to limit blast damage to surrounding rock. The exact mechanism of energy transfer in such blasts, however, is not well understood. Interruption of the continuous explosive column in a borehole by means of stemming, or air decks, may also be viewed as another form of decoupled blast. Decoupling of the explosive charge from the borehole wall affects both explosive energy release and explosion pressure developed in the borehole."

Jan 1, 1988

By A. L. Rutledge, R. S. Nichols

"Waste dump development at the Fording River Operation s in British Columbia began in 1971. In 1981, several unique as well as unplanned situations provided an opportunity to study water flows through waste dumps.The key to the drainage is naturally segregated rock sizes .created by end dumping from the crest of a pile. The largest size material accumulates at the toe. Flow rates along the base of the studied dumps varied from 2,800 to 13,500 m3/day or 0.032 to 0. 156 m3/s (1.2-5.5 cfs}. Sediment concentrations in the water ranged from 1 to 1,800 mg/I.This paper describes water flows through dumps of varied lithology and maturity. The results suggest that neither long-term water flow nor contained sediments in small streams are jeopardized when crossed by end-dumped fills.IntroductionThe Fording River Operations are located in southeastern British Columbia approximately 115 km north of the United State s and 10 km west of Alberta, within the medial range of the Rocky Mountains. All production is carried out at elevations ranging between 1,600 and 2,200 m above sea level.The property is within a continental climatic zone, with temperature extremes of - 40°C in January to +35°C in July. The average annual precipitation of 335 mm of rainfall and 390 cm of snowfall feeds the numerous seasonal, small drainage courses along the Fording River valley.Since start-up in 1971, 149 million bank cubic met res of waste from truck-shovel and dragline mining have been placed in numerous dumps or ""spoils"". The dumps were developed to the point that several unique situations could be studied. During the peak run-off period of May-June 1981, water flow studies were performed on dumps of varied lithology and maturity. This paper describes the results of the study."

Jan 1, 1982

By H. T. John

"The objective of this paper is to demonstrate how the optimum cut -off grade can be calculated for typical large tonnage openpit mines. In the examples, it is assumed that the concentrator tonnage is fixed and that there are no market restrictions. The mining rate is assumed to be variable. This is usually the situation at an operating property.ModellingA model of the ore body is required to examine alternate cutoff grade strategies. The model must be accurate in its relationship between grade and tonnage. Table I shows a typical relationship between ore tons and grade for various cut-off grades. The average strip ratio is also shown. For higher cutoff grades, the ore tonnage is decreased and the ore grade is increased. Strip ratio increases with the cut-off grade.Using the relationship between ton s and grade, and assuming a homogenous, long life orebody, a simple calculation of the optimum cut-o ff grade can be made. The objective is to maximize the present value of cash flows. For the long life homogenous orebody example this objective is satisfied by maximizing present cash flows.Cash flow is calculated by subtracting operating cost from revenue . Operating cost will increase with the cut -off grade as the strip ratio increases."

Jan 1, 1985

By Alfred B. Annor

The introduction and application of paste backfill over the past two decades has resulted in substantial benefits being realised by many backfill reliant mining operations who have used this technology. Paste preparation over this time period has relied basically on mechanical dewatering approaches that have included the use of centrifuges, thickeners, and vacuum and pressure filtration. In large bulk mining operations, this method of paste preparation has usually involved the construction of big and complex surface plants to meet large tonnage demands. These large plants usually have attendant high capital, maintenance and operating costs. The application of paste backfill in narrow-vein mining requires more flexibility in terms of fill preparation, transportation and placement. The method of paste fill preparation should take into consideration low manufacturing and operating costs, ability to use existing facilities at mine sites, simplicity of operation and flexibility of preparing fill over a broad range of consistencies. This paper will review alternative paste fill preparation methods and indicate those that might be better suited to narrow-vein mining.

Oct 1, 2001

By J F. Short

The jet piercing process, developed by Union Carbide Canada Ltd., is well established in blasthole production in open-pit mining. By this process, holes can be drilled, shaped and chambered for blasting. In suitable ore or rock formations, a considerable cost reduction can be achieved. This paper reviews the equipment used, relates how cost savings may be accomplished, and concludes with a mention of the most recent developments in this field. JET piercing and chambering, a process for blasthole production in open-pit mining, leads, in many instances, to improved drilling and blasting techniques and costs. It is a method of working rock with a supersonic flame and, to be most effective, depends upon a characteristic of the rock called spallability. Spalling, in this case, is the breaking away of surface particles from the rock body due to stresses caused by the thermal shock of the jet flame. Various rock properties contribute to this action, but, in general, the harder the rock the greater the spallability and the more effective and economical is the jet process. The jet process has the capability to drill, ream, shape and chamber holes for blasting.

Jan 1, 1965

By Sheila E. Daniel

"Since 1989, the Mine Environmental Neutral Drainage Program (MEND) has sponsored research into ways of reducing the environmental impact and financial liabilities associated with Acid Mine Drainage from tailings and waste rock. Toward this overall objective, Kilborn was contracted to review the use and applicability of passive treatment systems for acid mine drainage.Experimentation using passive systems to treat acid mine drainage has been ongoing since the early 1980's in North America. Passive treatments are generally considered an attractive alternative to active lime treatment, since they require minimal human involvement, no power, and only seasonal or periodic care and maintenance after establishment. Most attractive is that initial capital cost to implement a passive treatement system is generally low to moderate. Ongoing operating costs are similarly low when compared to active treatment systems.Passive treatment systems currently used, or under investigation to treat acid mine drainage include: anoxic limestone drains, aerobic wetlands, reed bed wetlands, compost wetlands, microbial systems and bioabsorption systems. These wastewater treatment systems utilize the chemical, biological and physical removal processes that occur naturally in the environment to improve wastewater quality, including: oxidation, reduction, coagulation, adsorption, absorption and precipitation; microbial activity; and, gravity aeration and dilution. The rates at which these processes occur determines the loading which can be treated and the effectiveness of the system.The results of our literature review will be summarized, and insight provided into the applicability of passive systems to treat acid mine drainage from Canadian Mines."

Jan 1, 1995

By B. Burke

Magnesium and its alloys are attractive materials for use in automotive and aerospace applications because of the low density and good mechanical properties. However, difficulty in forming magnesium and the limited number of available commercial alloys limit their use. The present paper reviews the efforts to improve the attractiveness of magnesium through non-traditional processing, and presents preliminary results of current work on producing magnesium alloys via powder metallurgy P/M. P/M can be used to alleviate the formability problem through near-net-shape processing, and also allows unique chemical compositions that can lead to new alloys with novel properties. The feasibility of producing magnesium powder metallurgy products utilizing the industrially dominant process of mixed powder blending, uniaxial die compaction and controlled atmosphere sintering was investigated. An alloy composition based on the commercial Mg alloy AZ31 (3% Al, 1% Zn) was used to facilitate comparison to similar wrought products. The optimal processing conditions (compaction pressure, sintering time and temperature, and quenching temperature) were found to maximize sintered density and mechanical properties.

Jan 1, 2007

By Harvey McLeod

M3 -Technology HOWEVER:In practice we have limitations ?Clients: aggressive or cost based; inexperienced ?Consultants: ?expanding market w/training limitations ?Prescriptive designs ?Lack of senior oversight ?Regulators: difficult to retain technical capacity ?Stakeholders: perceptions and expectations ?Physical settings: challenging terrain, climate, soils/rock Do M3?s Perform? YES?Generally M3?s since mid-1960 do perform ?BC Closed Mines: Afton, Highmont, Trojan, Bethlehem, Cheni, SNIP, NO?ARD/ML issues?e.g. Equity Silver, Samatosum; selenium, cadmium, sulphate

May 1, 2010

By J. Roth

"While not taking issue with the general thesis expressed in Dr. Ridge's analysis of the role of genetic concepts versus observational data in ore exploration (Ridge, 1983), the criticism could be offered that the author tends to slight the importance of conceptual (i.e. theoretical) models in mineral exploration.As a general rule, observational data in science lacks significance and utility without a theoretical construct to organize those observations. Theory in turn dictates what observations are made-and which ones are judged important. Thus, for example, prior to the elaboration-and acceptance- of the current model for volcanogenic base metal deposits, the structural aspect s of these deposits were most closely observed and studied by explorationists. The nature of the enclosing rocks and any attendant alteration was given minimal attention, and certainly didn't figure prominently as an exploration guide.Similarly, the importance of alteration features to exploration for porphyry copper-molybdenum deposits was only perceived when a theoretical model was developed to account for these aspects. Indeed, many of these porphyry copper deposits were regarded as epigenetic vein deposits by geologists of an earlier era observing and examining on a different physical scale-and with a different theoretical bias.In constructing and evaluating such conceptual models, explorationists primarily rely on observation data and proximate associations; speculative thoughts as to ultimate provenance or crustal evolution clearly play a subordinate role, as Dr. Ridge argues. This, however, should not obscure the fact that concepts and theories do indeed exert a major influence in mineral exploration."

Jan 1, 1983

By G. J. Hutchins

Precision surface mining is gaining traction in the iron ore, copper, iodine, limestone, bauxite, coal and gypsum markets. In this paper, we first address the possible improvements of a surface miner control using GPS techniques. An application in an iron ore mine in Western Australia is presented. The second item addressed is improvements of a new drum driving technique for a 100 ton surface miner. This technique involves installing a slow speed hydrostatic motor directly on the cutting drum rather than driving the drum through chain and sprockets. Details of the performance of this direct-drive versus the chain-drive are detailed. In addition to the 100 ton machine, we also present a 200 ton surface miner. This larger machine has 1600 hp (894.8 kg), and has been successfully introduced into a large iron ore mine in Western Australia. Performance of the 200 ton surface mining machine in various rock hardnesses is detailed. Some comments on the cost effectiveness of using a built-in loader versus loading with wheel loaders are included.

Aug 1, 2013

By P. Venkatasubramanian

"In recent years, computer based ""expert systems"" have been taking on large complex tasks for which no exact algorithmic solutions are feasible; tasks previously reserved for human experts requiring empirical knowledge, judgment, experience, developing a ""best solution "" by the use of plausible reasoning. Mining method selection is an appropriate area for the application of an expert system because extensive and detailed knowledge is required to make a ""best"" interpretaion of frequently ambiguous geological information. The expert system model presented here would enable users to apply expert knowledge to the evaluation of methods for coal deposits mineable by underground methods. IntroductionIn an increasingly complex and specialized world, human expertise spanning scientific, economic, social and political issues plays an increasingly important role in all branches of engineering. This is especially true of mining engineering. The number of scientific and professional disciplines involved in mine planning and evaluation, illustrates the problem. A conservative list includes geology, geophysics, geotechnics, hydrology, mining, environment, and economics.Engineers are almost obliged to be experts in at least one of the above disciplines if they are to handle the volume of information required in the planning process. Although computers have become indispensable tools in many endeavours, there is continued reliance on the human expert's ability to identify and synthesize these diverse factors, to form judgments, evaluate alternatives , and make decisions . This is especially true with regard to problems that are not easily amenable to precise formulations.The precious resource of human expert is also fragile and transient. The departure of a crucial expert from an organization ma y cause serious dislocations. Senior experienced people impart their knowledge of younger colleagues, but the demand for their talent may not leave sufficient time for such educational efforts. In recent years, computer based "" expert systems"" have been taking on large complex tasks for which no exact algorithmic solutions are feasible; tasks previously reserved for human experts, requiring empirical knowledge, judgment , experience, developing a ""best solution"" by the use of plausible reasoning."

Jan 1, 1988

By D. Y. Kim

This paper shows an approach that a gondola-typed robot recognizes walls on building facades. It is applicable for autonomous or teleoperated building façade painting robots. The robot may react based on the wall classification data. This approach is based on 2D LRF(two-dimensional Laser Range Finder). The robot acquires relative distances to walls, and a Kalman filter decides correspondence of walls. An ARS(Attribute Reference System) sensor helps convert LRF coordinate to global coordinate. The experimental results demonstrate the conversion of LRF data.

Aug 1, 2013

By M. Nowak

Extreme high grades often exert too much influence on surrounding block estimates, leading to a smearing of high grades that can cause overestimation of mineral resources. This concern underlies the decision to cap high grades, i.e., to lower the highest grades in a drill hole data set to some level deemed to be reasonable for producing reliable resource estimates. The choice of a capping level can, by itself, have a large influence on the analysis of the economic viability of a project. Despite this, it is often a choice that is made arbitrarily, guided more by art and tradition than by sound technical analysis. This paper makes suggestions for good capping practices, using methods and procedures that have been presented elsewhere, in the technical literature and in conference papers. The authors propose to use capping only if absolutely necessary, and review examples of cases where capping may not be necessary, or where capping does not make the estimates more reliable. It addresses two particular instances where capping is recommended: (1) where there is good reason to believe that estimation with uncapped grades will overstate the true underlying average grade, and (2) where there is potential for overly optimistic assessments of local block grades in the vicinity of some very high grade assays. The proposed capping practice is based on adjustments to only a very few high grade assays. The level of this capping can be assessed by bootstrapping and through analysis of the effect of extreme values on summary statistics like the average and the coefficient of variation. The paper recommends that good practice include an examination of the potential for local overestimation in higher grade areas.

Aug 1, 2013