Search Documents

By J. P. Messervey

THE story of the efforts made by the Department of Mines of Nova Scotia in the search for and investigation of mineral resources for the Canadian war effort began in the spring of 1937. During the past five years, however, heavy enlistments in the Active Service Forces by employees of the mining industry of the Province caused a recession in the production of coal, salt, and other essential minerals required to keep industry rolling on a wartime basis. A marked increase was shown during the period in prospecting for 'strategic' minerals, not only by individuals but also by some of the foremost mining companies. The Provincial Government offered encouragement in this field of endeavour by the enactment of legislation whereby the prospector was enabled to secure the maximum area of ground in a prospecting license at a minimum of cost. The labour requirements on the ground staked, however, remained unchanged. The Nova Scotia Department of Mines continued active investigation of minerals vital to the war effort. These included fluorspar, barytes, diatomite, limestone, and coal. Fundamental knowledge concerning the geology and mode of occurrence of these minerals was accumulated and extensive diamond drilling was carried out on the promising occurrences. Work in these fields is being continued.

Jan 1, 1945

By A. B. Irwin

Abstract The techniques used in recognizing, recording, and interpreting structures in the Slocan sedimentary ceries in the West Kootenay district of B.C. are presented here in the hope that they will be of use to others working in complexly folded areas. The general pattern of folding in the Central Slocan area is obscured by lack of outcrop over a large part of the country, lack of marker horizons, local complexities of folding, and several systems of faulting. 1t was found necessary to observe and record in great detail all primary and secondary structural features and to analyse those observations on a statistical basis. The determination of bedding tops as well as bedding attitudes proved to be of fundamental importance in determining the pattern of folding. The interpretation of secondary linear and planar structures confirm:; this pattern. Accordingly, the thickness of the Slocan sedimentary series is computed to be several times that formerly postulated. Introduction The data upon which this paper is based were collected largely during the field seasons of 1947 and 1948 when the writer was employed by the British Columbia Department of Mines on detailed mapping in the Slocan mining camp. Additional observations were made by the writer during 1950 when engaged in property examinations for the Geological Survey of Canada. This presentation is largely a condensation of part of a more comprehensive thesis (5) and is restricted to observations and conclusions pertaining to the mapping of complex folds, stripped of any hypothetical discussion. Except for some unique occurrences of primary structures, there are no features or techniques described here which are not presented in standard textbooks on structural geology. It is felt that the major contribution of this paper is the method used in applying these standard techniques to a specific field problem and in interpreting the results.

Jan 1, 1951

By R A. Stevenson

The purpose of this paper is to outline a recent development in ground fault protection. The paper deals with the A problems of both grounded and ungrounded systems, with regard to hazards to personnel and equipment, and shows that the increased sensitivity and speed of operation of this new detector results in increased safety to personnel and reduced stresses on equipment, and permits the detection of leakage currents before they become serious faults. The detector can be applied to all distribution systems, either A.C. or D.C., up to 15 kv., and the detector itself can be tested at regular intervals without interrupting line circuits. T HERE is always controversy among engineers as to whether distribution systems should be grounded or ungrounded. There are many experi-enced engineers on both sides of this controversy, and each have valid reasons for their choice

Jan 1, 1964

By C. W. MacLeod

LOCATION The Goudreau gold area in Ontario extends from a point a short distance south of the main line of the Canadian Pacific railway, at Lochalsh, in a south-westerly direction to the Magpie river. It crosses the Algoma Central & Hudson's Bay railway at Goudreau station, 177 miles north of Sault Ste. Marie. The area is roughly 25 miles in length by 6 miles in width. The potential gold formation is much more extensive but little prospecting has been done outside of the limits mentioned. The actual continuous area of Keewatin formation, in which gold has been found, is one of the largest in Ontario. ACCESSIBILITY Probably no mining area in a similar stage of development has had the excellent transportation facilities which Goudreau enjoys. This field is traversed in part by the main lines of the Canadian Pacific and Algoma Central railways. The Provincial Government has constructed 22 miles of road through the heart of the camp. Sixteen miles of this road is suitable for motor car traffic and several cars and trucks are in constant service.

Jan 1, 1926

By B. Daniels, A. Tieu, W. Yan, B. Ren, M. Vijay

"Plasma or thermal sprayed coatings are becoming more widely used in a wide range of industrial applications. The preference to use thermal sprayed coatings is mainly attributed to its superior wear, and corrosion resistant properties akin to hard chrome but without the harmful health implications of chrome in the coating process. Specifically, High Velocity Oxygen Fuel (HVOF) plasma sprayed Tungsten Carbide & Cobalt (WC/Co) coatings are presently being tested on aircraft landing gear. This coating can be efficiently applied and is highly resistant to corrosion and wear. However, HVOF coating's durability also makes it difficult to be stripped for inspection and overhaul. Current coating removal methods usually involve a multi-step process whereby the coating must undergo diamond wheel grinding, chemical dipping, grit blasting, ultrahigh pressure (UHP) 380 MPa (55 Kpsi) water blasting, and subsequent chemical dipping, depending on the type and thickness of the coating. As explained by Yan, et al [l]"" a unique method has been developed for removing HVOF coatings with the use of only water. The method consists of modulating a stream of water at a pressure of only 69 MPa (10 Kpsi) with ultrasonic waves to generate a forced pulsed waterjet. The resulting cyclic loading of the hard coating due to the impact of the water pulses easily causes it to flake off the substrate. This paper will briefly describe the fundamentals of the forced pulsed waterjet technique with an emphasis on insitu applications of the removal of various plasma and HVOF coatings."

Jan 1, 2006

By T. Richard Davies

This paper primarily deals with the application of wearfacing materials and their role within a well-established preventive maintenance welding program. Some examples are shown, as well as a synopsis of possible benefits and a compendium of methods and materials.

Jan 1, 1979

By Andrzej Luszczkiewicz, Magdalena Duchnowska, KGHM Polska Miedz S. A., Witold Pawlos, Jan Drzymala, Alicja Bakalarz, Przemyslaw B. Kowalczuk

A pre-flotation process of the Kupferschiefer ore with only frothers produces a concentrate enriched in carbonaceous matter and tailings for further upgrading steps. A partial removal of easy-to-float components of the feed before the main enrichments steps by flotation (rougher, scavenger) improves overall efficiency of separation of valuable elements from the ore. Since the types and doses of frother used for pre-flotation effect the process, the aim of this study was to determine the influence of selected frothers on the efficiency and selectivity of the Kupferschiefer ore processed by KGHM Polska Miedz S.A. A series of pre-flotation tests in the presence of different poly(propylene glycols) ethers, poly(ethylene glycols) ethers and aliphatic alcohols were conducted. The obtained results indicated that the types and doses of frother determine the flotation selectivity of copper and total organic carbon. The evaluation of the pre-flotation process was based on the analysis of selectivity parameters calculated from the recoveryrecovery Fuerstenau upgrading curves as well as the values of copper and organic carbon grades in the flotation products. It was shown that pre-flotation performed in the laboratory scale using a suitable frother provides higher overall flotation selectivity of organic carbon with lower overall flotation recovery of copper in comparison to flotation without the pre-flotation step. Thus, the pre-flotation process improves the quality and quantity of the final concentrates produced from the Kupferschiefer ore.

Jan 1, 2016

By L. C. Johnston, J. N. Gills

This paper reviews the basic reactions of the blast furnace and the open hearth furnace, and then discusses the quarrying and sizing requirements of the limestone feed for each. Particular emphasis is placed on the lime-stone at Irish Cove, now being mined under an agreement between Scotia Limestone Limited and Dosco Steel Limited. The drilling and blasting operations are described, along with loading and haulage, plant flow, water supply, power supply and transportation facilities.

Jan 1, 1967

By N. Bakhshizadeh

In this investigation, the aging effect on creep behavior of A12024-10%SiC composite fabricated by powder metallurgy was studied. P/M bars were manufactured by hot powder extrusion method at 450°C with a ratio of 16 to 1. Creep specimens were over-aged at 187 ºC for 43 h. It was found that almost full density composite with relatively homogenous distribution of reinforcing particles throughout the aluminum alloy matrix could be attained by direct powder extrusion process. Creep tests were conducted at temperatures from 275 to 325°C under stresses from 25 to 60 MPa. The analysis of the creep mechanism determined that dislocation glide was the predominant mechanism of plastic deformation. The activation energy of the creep process was found to be higher than that of lattice self-diffusion in pure aluminum.

Jan 1, 2007

By J. Edwin Van Buskirk

For a country that is as important a gold producer as Canada, the return to the gold standard of the major commercial countries of the world during the past five years is of particular significance. To the Canadian gold mining industry, the advantages of the gold standard are a matter of more than theoretical importance. According to economic theory, prices are determined by the relation between the demand for, and the supply of, money. The demand consists of the offering of goods for money; the more goods offered, the greater the demand. The supply consists of the total money available for the purchase of goods. The total supply of goods to be exchanged through the instrumentality of money remaining the same, an increase in the supply of money will, according to this theory, raise prices; conversely, a decrease in the supply of money will lower prices. Let us imagine that everyone in the world suddenly had twice as much money, and that the sum total of all goods remained the same. Is it not obvious that we would pay just double the price for these goods? In Canada today, most people have approximately 50 per cent grea.ter income than in 1913, and the average price for all articles sold in Canada is 50 per cent above those in 1913.

Jan 1, 1928

By D. Yamada, T. Tanaka, N. Inouchi, J. Nakahigashi, H. Yoshimura, T. Nonishi

The use of cereal food materials as lubricants was investigated in an attempt to develop nonpolluting lubricants. Suspensions of wheat flour in water and other types of cereal food lubricants were prepared and their friction coefficients measured. The results indicate that a cereal food lubricant containing 30% lipids, 2% proteins, 60% carbohydrates and 0.6% calcium carbonates has the lowest friction coefficient for a sheet (cpTi-1). As example applications, the lubricant was tested with a forming press and a screw-fastening device. In both applications the cereal food lubricant performed relatively well in comparison to conventional lubricants and thereby has potential for practical applications.

Jan 1, 2006

By N. Staroselsky

"Significant energy savings are often possible for centrifugal compressors operating in parallel by improved control strategy and improved instrumentation. Blow-off can usually be reduced by improved surge control combined with a better control strategy for loading and unloading the group of machines. More precise and stable pressure control then becomes possible. This improved control strategy will also decrease the frequency of operation near the dangerous limits of surge or overload or overspeed. A sample station of mixed centrifugal and reciprocating compressors is examined and a substantial energy saving with the recommended control strategy is projected from operating data. Present Operating Conditions of the Compressed Air StationThe Compressor StationThe compressor station described here has three centrifugal compressors and three reciprocating. It supplies a mine in New Brunswick.Compressed Air and Power ConsumptionFigure I and Figure 2 provide graphs of air consumption and pressure changes based on the owner's data.During the typical two-shift operating day (Fig . I) in the non-productive shift (midnight to 8:00 a.m.), the consumption stays at a level of 9,000 SCFM. This corresponds to a pressure of 110 PSIG. Then, after 8:00 a.m ., the air consumption starts to increase and th e pressure decreases. Around 10:00 a.m., the consumption reaches its maximum level at 97 PSIG. Around II :30 a.m., the air consumption starts to decrease because of the production drop during the lunch break of the first shift. Pressure increases again up to 109 PSIG. After the break, consumption rises to its maximum level over 16,000 SCFM andpressure drops to 97 PSIG.Around 2:30 p.m., the air consumption drops sharply to 9,000 SCFM because of the production decrease to zero level. This drop results from changing of shifts. The pressure at this time increases again up to 110 PSIG. The second shift (2:30 to II :30 p.m.) is an alogous to the first.During the three-shift operating day, the break around 4:00 . a.m . and the shift change around 6:30 a.m. cause sharp drops in air consumption. The pressure for almost the entire night shift stays near 110 PSIG because the station is working with blowing-off even under the maximum consumption. The analysis of Figures I and 2 shows that the pressure varies with the air consumption changes. During non -productive time (non-production shifts , shift changes and breaks) or during the night shift, the total station capacity is proportional to the discharge pressure. By decreasing the level of this pressure up to 97 PSIG, the flow of the station may be decreased during the non-production time as follow s:"

Jan 1, 1980

By W. L. Ott, C. L. Lewis

"AbstractA technique is described for preparation of palladium sponge and for spectrochemical analysis of the metal in this form. The precision and accuracy of the method are discussed. Analyses are compared with previous spectrochemical analyses of palladium in the black form. Good agreement was found in the two sets •of results and it is concluded that they are more reliable than wet chemical .analyses of the same material.IntroductionFOR SEVERAL YEARS the problem of platinum metal analysis by spectrochemical methods has been under investigation at the Spedtrographic Laboratory, Department of Geological Sciences, Queen's University. The problem, briefly -stated, is as follows: Samples of platinum, palladium,-rhodium, ruthenium, and iridium are received as fine metal powders, called sponge. Direct spectrographic analysis of this material has not been found satisfactory due to its heterogeneity •as regards contaminant metals, which may be present up to a total of one per •cent or more. Further-more, spectrographic standards are difficult to obtain and difficult to prepare accurately by adding weighed portions of contaminant metals to the sponge. The fact that •contaminant metals in original samples are probably alloyed with the major constituent is a further difficulty since complete fusion of these refractory metals proved impractical in the present case as a means of standard preparation. It •has, therefore, been found most satisfactory to dissolve the metals, prepare standards by addition of solutions of contaminant metals, and to reduce both standards and samples to a homogeneous form. A previous paper, by Hawley, Wark, Lewis and Ott (2) dealt with a method for spectrochemical analysis of platinum and palladium in their black form. Since completion of research on the black technique, the possibility of analyzing palladium accurately in its sponge form has• been investigated."

Jan 1, 1953

By A. W. Jolliffe

DESPITE the widespread occurrence of scheelite in Canada, domestic production of this strategic mineral is still quite insufficient to meet wartime needs. Two difficulties have invariably arisen in prospecting for or developing scheelite deposits: scheelite is a difficult mineral to identify, and secondly, its distribution is commonly so erratic that the value of a deposit cannot be determined without arduous and expensive methods of sampling and wet assay. Scheelite's property of fluorescing under certain ultra-violet lamps overcomes the first difficulty and is the basis for a quantitative method developed to overcome the second. It is found that, by use of an ultra-violet lamp, the value of many scheelite deposits may be accurately and speedily determined. The method requires neither elaborate apparatus nor exceptional skill on the part of the operator, and is most applicable to those deposits where the bulk of the scheelite occurs in fairly pure aggregates that are at least one-tenth of an inch across. It has been used in grading some two hundred scheelite-bearing veins in the Yellow-knife-Beaulieu region, Northwest Territories, and various occurrences in the Porcupine district, Ontario. The method requires the measurement of the total area of scheelite exposed in any reasonably large measured cross-section of a deposit. From the areal percent of scheelite so obtained, the tungstic oxide (WO,) content of that part of the deposit may be calculated by means of equations of simple derivation.

Jan 1, 1942

By Richard Cyr, Peter Larsen, William Quesnel

"The need to continually improve efficiency and lower costs in mining operations is of paramount importance to all concerned in the industry. Mining operations are constantly testing new methods and equipment in order to lower costs and improve productivity. Equipment suppliers strive to fulfill the demands of the mines through improved design and innovative ideas for productivity increases. In some cases, however, an increase in productivity does not require new equipment design, but rather the application of an existing mining method into different operating parameters. Such is the case in applying longhole methods to narrow vein ore deposits.Bulk mining methods have long been recognized as efficient, low-cost alternatives in narrow vein operations. Typically, shrinkage and some cut-and-fill methods are employed. The shortfall of these methods is the tendency to be labour intensive. The demand for miners skilled in these methods far outweighs their availability. Consequently, labour-efficient methods have to be employed to fill the void. The application of longhole drilling techniques to narrow vein deposits is one such method.IntroductionPercussion longhole drilling evolved in Canada in the early 1940s. Prior to percussion drilling, blast holes were drilled using diamond drill equipment. Jack Gardner, of Gardner Steel, began testing with carbide percussion bits and extension drill steel in applications where diamond drills had been previously employed. Percussion drilling equipment proved to be considerably more productive and cost-efficient. The experiment eventually led to the replacement of diamond drills in this application.Over the years, the percussion methods were improved, with particular emphasis on the equipment used. Rifle bar rotation machines evolved to independent rotation. Bar and arm set ups evolved into self-contained mobile drill carriers that increased productivity while reducing the physical labour. The introduction of hydraulics further improved efficiency and production figures. Today, it is not uncommon to see fully computerized jumbos in production longhole drilling applications. These machines represent the ""state-of-the-art"" in longhole drilling equipment.Production longhole drilling is considered to be one of the most efficient bulk mining methods in use today. Production statistics normally exhibit low-cost, efficient ore extraction. As a rule, longhole (blasthole) methods are associated with substantial ore deposits. These methods have exhibited high production figures and low mining costs.Over the past decade, long hole methods have been applied to several narrow vein deposits. These applications have proven that, given the right parameters, longhole methods will produce the same advantages in narrow vein deposits as are seen in more conventional applications."

Jan 1, 1990

By D. R. Reeves

This paper describes the geophysical Jogging of coal that is being carried out for the National Coal Board in the United Kingdom. An explanation of the technique is given and results are presented showing estimations of seam thickness to within ±0.5 in. and ash content to accuracies of ±2.5 per cent. The basic method of interpretation is outlined and some conclusions regarding the conditions of roof and floor material which may be deduced from the logs are explained. An indication of future developments in this field, including the identification of coal type and moisture content, is given.

Jan 1, 1971

By D. Sanguinetti, A. Consigny, M. Nodwell

"Alkali precipitation of dissolved metals is an inexpensive but non-selective means of treating mine wastewater. Alternatively, sulphide precipitation can treat to below parts-per-million concentrations while selectively recovering valuable metals. While technically feasible, sulphide treatment of dilute waste streams increases the size and cost of the plant relative to the metals loading. Ion exchange has been applied at two separate sites to pre-concentrate nickel containing wastewater prior to recovery in smaller and more cost effective sulphide precipitation circuits. The result is a dual-circuit system that can maintain high selectivity and reduce overall facility cost while meeting strict effluent regulations.INTRODUCTIONAlkali precipitation using lime is the most common method of treating mining effluents for dissolved metals removal. This method is generally sufficient for waste streams containing mixed metals of little value, and for meeting modest metal concentration limits in the final effluent. Due to the non-selective nature of the lime process, the produced metal hydroxide sludge is of little value. All metals are removed together in a sludge product which cannot be re-processed for further value recovery.By contrast, sulphide precipitation can be used to selectively remove and recover valuable base metals (such as copper, zinc, nickel and cobalt), since the sulphide will preferentially target these metals without reacting with less valuable metals (such as iron and aluminum). The low solubility of the metal sulphide solids also supports the removal of base metals to lower concentrations than can be achieved with alkali precipitation in addition to other benefits discussed more fully in a prior paper (Bratty, Lawrence, Kratochvil & Marchant, 2006). The corollary to this solubility feature is that sulphide precipitation can function on influent streams containing low (< 10 mg/L) metals concentrations to meet very low parts-perbillion final effluent concentrations. Reagent overdosing is also minimized when compared to alkali precipitation."

Jan 1, 2012

By F. Chiesa

The permanent mould process, which is a favoured process for producing premium quality aluminium casting, is rarely used to produce magnesium alloy parts. This may be attributed different factors such as: the reservation with which the automotive industry considers using magnesium in structural castings; also the relative hot shortness of most magnesium alloys when compared to aluminium A356/357 is another factor. A third reason stems from the fact that the "heat content" of magnesium is much less than that of aluminium, resulting in the difficulty, for a relatively slow process such as permanent mould (versus pressure die casting), to reach a mould dynamic equilibrium temperature sufficiently high to avoid premature freezing and misruns. The present work will address this problem by carrying out controlled cycling of a laboratory mould, poured with aluminium and magnesium alloys. The influence of insulation of the mould and artificial electric heating on the run-in mould temperature will be determined experimentally. A thermal model will be sought for these thermal devices that will allow to predict the thermal behaviour of moulds of different geometry before a single casting is poured. The model will be tested on an industrial casting in a workshop environment.

Jan 1, 2006

By Y. A. Grinin, M. A. Liamina, V. A. Shumskij, Y. I. Sannikov, M. V. Radashin

"A brief history of the development of the Kivcet flash smelting process is presented. The broad scope of the process with an ability to treat high grade lead sulphide concentrates, as well as oxidized lead-zinc residues, is emphasized. Fine coal in the charge serves two purposes, one as auxiliary fuel and the other as a pre-reductant for ferric iron in residues. Current Kivcet operations incorporate a layer of coke or “coke checker” at the surface of the slag in the reaction shaft that acts as a reducing agent for flame products or slag that flow through it. Details of this invention, are given. IntroductionFor many years, the sinter-blast furnace lead smelting process has been the main internationally accepted method used for the production of primary lead metal. In recent times, this process has been unable to meet legislated environmental restrictions and it became clear in the mid-1960s that a new and cleaner process would have to be developed. The present level of Kivcet performance was developed in three main stages:1. flash smelting natural sulphide lead raw materials with the attached electric furnace for production of lead bullion and crude zinc;2. natural raw material smelting with lead and zinc separation in a “coke filter” or “coke checker” at the surface of the slag in the reaction shaft to produce lead bullion and ZnO-bearing slag that can be fed to conventional slag fuming; and3. processing of oxidized lead-bearing raw materials, such as low grade zinc plant residues, with the production of lead bullion and ZnO-bearing slag periodically directed to slag fuming."

Jan 1, 1998

By S. Luidold, A. Poscher, H. Antrekowitsch

"The rare earth elements (REE) are nowadays mainly used for permanent magnets, catalysts, hydrogen storage alloys in rechargeable batteries, for glasses, ceramics, and polishing agents. Other important areas of application are phosphors in different types of lamps (fluorescent tubes, energy-saving lamps, etc.). These lamps are often collected and treated at their end of life by disintegration and sorting. However, the obtained fine fractions comprise not only REE-containing phosphors but also small amounts of mercury and are therefore disposed till today in special landfills. Due to the enormous price increase of the rare earths during the last two years, a lot of activities started for extracting these elements from secondary resources such as for example phosphors. All recycling concepts for this task mainly work with hydrometallurgical methods. The large number of different compounds in phosphors with sometimes very different behaviors with respect to their solubility in aqueous phases forms a major challenge to achieve good yields as well as acceptable purities of the produced rare earth concentrates by a process with a reasonable number of operation steps. Therefore, this paper gives at first a brief overview about the compounds, used as phosphors and about existing concepts or investigations. It further describes our own process design and the results, obtained on laboratory scale. INTRODUCTIONThe rare earth elements (REE) have a central position in the industrialised world despite their marginal production volume in comparison to common metals such as aluminium, copper, zinc etc., because they are essential for many applications. They often cannot be substituted without a considerable loss on functionality and quality. This group of metals comprise the lanthanoids (f–block elements, lanthanum–lutetium) as well as scandium and yttrium.The estimated world mine production of REE amounted to 133,000 t rare earth oxide equivalent in 2010, whereat China accounted for 130,000 t or 98 % (Cordier, 2012). The European Union (EU-27) imported 23,013 t in 2008 to cover its demand. The figure 1 shows the fraction of the European member states in terms of the total imports of rare earth compounds from outside the EU-27 (Schüler, Buchert, Liu, Dittrich, & Merz, 2011)."

Jan 1, 2012