Search Documents

By Malcolm Black

Introduction Before beginning to write this paper, I decided that I should first find suitable definitions of the words Sample and Sampling. The dictionary gives: "Sample.-A portion indicative of the whole"; and according to Baillie (1), sampling is "That process whereby a representative and comparatively small portion of material is selected from a large bulk, and preserved under such conditions as shall prevent contamination or avoidable alteration, with a view to the formation of valid conclusions regarding the suitability of the bulk for specified purposes". These comprehensive definitions are alike in substance, and indicate that unless a truly representative portion is taken, it is not a sample. Ore 'as mined' generally varies a good deal in composition, and, in crushing, segregation takes place. Some of the minerals present, due to differences in hardness and friability, break into smaller pieces than others, and, on reaching the bin, the coarse particles roll away, leaving the fines behind. The result of this segregation is generally quite noticeable on the conveyor feeding the mill, especially when the bin is nearly empty and the crushing plant shut down. Should the sampling period synchronize with either the coarse or the fines, the sample obviously would not be representative. I agree that this is rather far fetched, but I maintain that such a condition is possible. Assuming that a representative sample may be procured from the feed conveyor, the method of cutting it down for assay has considerable influence in maintaining the original condition of the sample. The finer the material is ground after each cut, the more uniform the sample will remain. To illustrate this point, let us take a quantity of fine sand and add, say, three grains of rice to represent metallic particles. We may mix this sample by any of the known methods, then cut it into four equal portions. It is obvious that at least one of the portions will be without a rice grain. But let us grind the three grains of rice into flour and proceed as before. Now there will be a much greater chance of including some of the rice in each portion.

Jan 1, 1935

By Daniel Murray

"ACCIDENT PREVENTION in and around coal mines presents many problems of a type which are not encountered in any other industry. This is particularly true of the coal mines in Nova Scotia, where the underground workings are very extensive and the area of exposure to workmen is very great.Roof conditions at the coal faces and in the waste change very rapidly, almost from hour to hour, and it is at these places that the greatest dangers exist and where most mine accidents occur. It is only natural, therefore, that our attention, as far as accident prevention is concerned, should be concentrated •at the coal faces and in the waste, especially in mines where the longwall system is used in the operation •of the seam.It has been said that no hard and fast rules can be set down for timbering at the coal faces and in the waste in the coal mines in this area. We do not subscribe to this theory, however, for the following reasons:On the longwall faces in No. 18 Colliery of the Dominion Coal Company, Limited, where the 'Dosco Miner' has been in operation and where there is a very rigid system of timbering and roof supports, which is strictly followed, only one compensable accident has occurred on those faces from May 2ndJ 1950, to the time of writing this paper, February 3rd, 1953.The 'Dosco Miner' has worked on four different longwall faces in this mine and has mined and loaded some hundreds of thousands of tons of coal."

Jan 1, 1953

By W. Fergusson

This paper takes a look at the use of rubber to provide corrosion resistance and wear resistance in the mining industry. The longer life and reduced down time involved with the use of rubber are stressed, and examples are given of applications in grinding mills, skips, discharge chutes and screens.

Jan 1, 1979

By Trygve Høy

"Important stratabound lead-zinc deposits in southeastern B. C. occur in rocks that range in age from Proterozoic Helikian to Middle Cambrian. The Sullivan deposit, and similar but smaller deposits in the Sullivan area are the only important deposits that occur in clastic rocks with little carbonate content. The highly deformed and metamorphosed Shuswap deposits, of probable Hadrynian to Helikian age, are in mixed marble, calc-silicate gneiss and pelitic schist assemblages, rocks transitional between clastics and carbonates. Deposits in younger rocks, such as the Kootenay Arc deposits in the Lower Cambrian Badshot-Reeves Formation and the Monarch -Kicking Horse deposits in Middle Cambrian dolomite, are hosted by platformal carbonate rocks.An important regional control for the distribution of deposits appears to be a northeast-trending tectonic zone that crosses the Rocky Mountains and the Purcell Mountains just south of the Sullivan area, and projects southwestward toward the Salmo camp at the southern end of the Kootenay Arc. Pronounced northeast-trending gravity and magnetic anomalies, basic volcanism of Hadrynian age (the Irene volcanics west of Creston) and a preferred alignment of Mesozoic granitic rocks indicates that the zone coincides with deep crustal structures. Within the zone are dramatic and abrupt thickness and facies changes in Hadrynian Windermere rocks and lower Paleozoic rocks, and on the east side of the Rocky Mountain Trench in Helikian Purcell Supergroup rocks, indicating that block-faulting was active intermittently within the zone from Helikian through to lower Paleozoic time. Right-lateral and reverse movements occurred on northeast-trending tear faults within the zone in Mesozoic time."

Jan 1, 1982

By D. S. Conochie

The world is poised for rapid growth in consumption as large, less developed economies acquire greater wealth. It might be expected that there would be a corresponding growth in waste generation, but this might not necessarily be the case. The metallurgical industry has an excellent record of process development which has allowed it to provide a high tonnage supply of low cost, high quality metals. Environmental challenges have been faced and indeed the recycling of scrap iron through the electric arc furnace has made a massive contribution to cleaning up obsolete structures and equipment of past generations. Issues in waste generation and processing still remain, and the expectation for cleaner processing and environmental performance continues to rise. The waste impact of key process developments of the last century and the recent developments in metallurgical waste processing in Canada will be outlined. The potential to use state of the art design tools to produce the next generation of zero waste processes will then be explored.

Jan 1, 2004

By H. Nakano

The codeposition behavior of impurities such as Ag, Bi, Fe, Ni, Pb and Sb with Cu was investigated galvanostatically at 5-3000 A/m2 using a Pt cathode at 60 °C in acidic copper (I) chloride (cuprous chloride) solution at pH1-2 containing 1.0 mol/L of Cu+ and 4.9 mol/L of Cl-. The impurities were classified into two groups: Group I (Ag, Bi) which codeposits with Cu as a metal, and Group II (Fe, Ni, Pb, Sb) which is slightly involved in the deposited Cu in nonmetal form from the electrolyte. Silver and Bi in Group I behaved as more noble metals than Cu, and significantly codeposited with Cu, showing typical features of regular-type codeposition. When Cu was deposited dendritically, the Ag and Bi content in the deposit increased with increased duration of electrolysis as a result of decreased net current density caused by increased cathode area. The current efficiency for Cu deposition in impurity-free solution was 95-100% over 100-1000 A/m2, but it abruptly decreased at above 1000 A/m2 when the limiting current density of Cu was attained. Although Fe, Ni, Pb and Sb in Group II were involved to 0.01-0.02 mass% in the deposit, they had no influence on the current efficiency or morphology of Cu.

Jan 1, 2007

By Roger Francis

There is increasing use of acid leach extraction methods at elevated temperatures and pressures by the mining industry. In many locations there are limited supplies of fresh water, and waters with higher chloride contents must be used, making conditions more corrosive. The fluids downstream of the main autoclave are hot, acidic, oxidizing and contain chlorides and present a challenge to the mining community to ensure reliable operation. Zeron 100 is a high strength superduplex stainless stee, that offers high corrosion resistance at a cost effective price. The paper presents a combination of laboratory data and service experience, particularly in the aggressive fluids found in downstream processing.

Jan 1, 2010

By A. Michalkow

DELN ITE Mines Limited is located in Deloro township, on the west end of the south break of the Porcupine Camp. Mining operations are currently being carried out on the downward extension of a system of quartz veins in an andesite zone. This zone has been followed from surface to the present bottom level of 5,250 feet. The changing mineralogy of the vein system has involved an increase in tourmaline content from the surface downwards, so that the veins at the lower levels are composed of dark brown quartz-tourmaline. The drilling problem presented by these extremely hard veins was partially alleviated by the development and adoption of a one-inch drill bit. All blast-hole drilling is now done with the one-inch bit, without any difference in hole spacing.

Jan 1, 1962

By P. Belley

Prior to 2006, the filtration unit for leached sludge treatment (filter press) permitted the filtration, washing and drying of cake to 17% (w/w) moisture. That year saw moisture content abruptly increase to 20% (w/w), drastically changing the rheological properties of the cake. The cake became sticky and agglomerated. This led to major disruptions of operations and plant capacity (cake release and cake conveyor problems, complicating the subsequent steps of the process). The conditions for the filtration, washing and drying, were simulated to ease cake unloading without aggravating dust emissions (moisture about 17% (w/w)). All of the laboratory tests yielded a moisture content above 17% (w/w). Therefore, we concluded that the moisture problems were not due to a recipe change in primary material, but to an operational problem in the filter press. Through the laboratory results, the filter press operating conditions (washing ratio, drying pressure and drying time) were optimized to enable a reduction in cake moisture to 17% (w/w).

Jan 1, 2007

By M. Jahazi, J. Gholipour

Design and manufacturing of parts using hydroforming process require knowledge about material behaviour and tribological effects during hydroforming. Lubrication is one of the key issues in successfully hydroform the tubes. A Ni-based super alloy tube with 50.8 mm (2 inches) outer diameter and 0.9 mm (0.035 inches) thickness is considered for this research to study the effect of lubricants on the formability of the tubes. Hydroforming of a hollow compressor blade is considered for this project. A combination of press forming and hydroforming is employed to produce the part. LS-DYNA, an explicit dynamic finite element code, is used to model the experiments. Different lubricants are modeled using different coefficient of friction in the model. Predicted results for strain distribution at a critical section of the tube are extracted for each case to evaluate the effect of different lubricants on the process.

Jan 1, 2006

By G. A. McGuffin

"IntroductionWITH the increase in quantity of sour gas reserves in the Province of Alberta, and the wider market for sulphur brought about by mounting world demand and restrictions placed on the principal supply, it was inevitable that this important source of sulphur would be .developed. In the light of these facts, it seems timely that a general paper on sulphur recovery from petroleum gases be presented. This, then, is the purpose of the following text. A short discussion of each of the following subjects is presented:(1) Properties and uses of sulphur(2) Existing sources(3) Market research(4) The recovery process in Turner Valley(5) Hazards of sulphur productionNo pretext of originality of material is made since innumerable reports have been prepared on this and related topics and information contained in these has been used quite liberally.Properties and uses of SulphurSulphur is a non-metallic element having an atomic weight of 32.06. The stable crystalline form at atmospheric temperature is referred to as 'rhombic' sulphur. It is bright yellow and has a specific gravity of 2.05, equivalent to 129.2 lb./cu. Ft. Above 204°F. sulphur has another stable crystalline form, referred to as 'monoclinic'. This is reddish-brown and is slightly less dense than the rhombic variety (122.4 lb./cu. Ft.). Sulphur in bulk form weighs 84 to 90 lb. per cu. Ft. Sulphur melts at approximately 240°F. to a straw coloured liquid which is quite viscous."

Jan 1, 1952

By O. B. Horne, R. O. Morgan, C. E. Anderson

"Air-photo interpretation and photogrammetry are two of the most effective and versatile tools available to the petroleum industry. The techniques have proven successful in providing solutions to many of the problems encountered in the design and construction of oilfield projects.Although most technical personnel are aware that air-photo interpretation and photogrammetry are useful in the selection of routes for roads and pipelines, few realize the true scope of the techniques or the wide variety of areas in which they are applicable.This paper briefly describes the principles involved, and reviews a number of typical applications of particular interest to petroleum companies. Excessive detail is avoided, rather the emphasis is placed upon the wide spectrum of possible applications. It is stressed that on-the-ground examination generally is a necessary adjunct, and that there are certain limitations to the techniques discussed.Properly applied, however, air-photo interpretation and photogrammetry can offer significant advantages in terms of time, flexibility, secrecy and economy."

Jan 1, 1968

By A. Sacit Saydam

"Induced polarization/resistivity and magnetometer surveys have been carried out over the Casmo molybdenite deposit in mountainous terrain of northern British Columbia. Molybdenite occurs in quartz-bearing fractures with or without pyrite along a zone of hydrothermal alteration and intense fracturing, believed to be a northerly dipping fault zone, within medium-grained equigranular and porphyritic quartz monzonite.The molybdenite-bearing zone is characterized by a significant resistivity low, a metal factor high and a subtle IP low flanked by highs outside the mineralized area. Magnetic trends, indicated by a magnetometer survey, generally parallel the zone and strike direction of the different intrusive phases, and have been helpful in delineating contacts and faults in the area.IntroductionThe Casmo molybdenite deposit is 6 km southwest of the asbestos mining town of Cassiar in northern British Columbia, at an elevation of 1,550 metres. Molybdenite was first discovered during the early 1950s and the first important exploration work was done in 1964. Between 1964 and 1971, about 25,000 feet of drilling was done by various operators, as a result of which 33.7 million tons of molybdenite ore was drill indicated at a grade of 0.123%. In 1979, Shell Canada Resources entered into an option agreement with the former operator, New Jersey Zinc Corporation. Shell completed 27,000 feet of diamond drilling between 1979 and 1980 and ha s reported 75 million tonnes of drill-indicated ore with an average grade of 0.13% MoS2• This paper is a case history of IP I resistivity and magnetometer surveys done over the Casmo deposit during 1979 and 1980."

Jan 1, 1983

"These guidelines have been prepared to assist the Qualified Person(s)in the planning and supervision of exploration programs which will be reported under National Instrument 43101. The Companion Policy of NI43101 references the guidelines and states that issuers and Qualified Persons should follow them.Exploration Best Practices GuidelinesPreamble: These guidelines have been prepared to assist the Qualified Person(s) in the planning and supervision of exploration programs which will be reported under National Instrument 43-101. Such exploration programs must be under the supervision of the Qualified Person who will be responsible and accountable for the planning, execution and interpretation of all exploration activity as well as the implementation of quality assurance programs and reporting. These guidelines are also recommended for use in the planning and execution of exploration programs which will not be reported under NI 43-101. This set of broad guidelines or ""best practices"" has been drawn up to ensure a consistently high quality of work that will maintain public confidence and assist securities regulators. The guidelines are not intended to inhibit the original thinking or application of new approaches, that are fundamental to successful mineral exploration.Results should be summarized and reported in a Technical Report of good professional quality in accordance with the National Instrument 43-101 and Form 1 contained in that instrument. All exploration work from which public reporting will ensue must be designed and carried out under the supervision of a Qualified Person (""QP""). A QP is defined in National Instrument 43-101 as an individual who is an engineer or geoscientist with at least five (5) years' experience in mineral exploration, mine development, mine operation or project assessment, has experience relevant to the subject matter of the project or report and is a member in good standing of a recognized professional association."

Jan 1, 2003

By Ursula M. Franklin

Old iron nails are one of the most common objects which entice the general public to ask questions about the history of metallurgy. There is a lot of history in old nails - history of the manufacturing industry, and social and economic history. Nails, therefore, are fine teaching tools; whether students have to acquire metallurgical skills or explore the structure and properties of wrought iron, whether they want to look into the history of inventions and the development of machinery, studying nails tells a story better than any teacher or any book. I have used this approach often and the following note is based on several student projects, particularly the work of Carmina Herrero and Vicky Marchant. Nails, those essential metallic fasteners, have long been with us. Their size, shape and design is basically a compromise between the makers' ability to control and manipulate material and the demands of the intended application. There were copper and bronze nails in antiquity, but in this paper I want to deal only with iron nails. In Rome, iron nails were common, and Cleere carried out the fine metallographic investigations on a large stock of nails recovered from a Roman fort site in Scotland. Those nails were hand forged; sorting them at the site on the basis of length, shape of head and shape of shank (in cross section) indicated that there seemed to have been some nail standardization. It appears that the Roman smiths used a series of heading dies starting with a 1/s-in. size. Each successive size increased by approximately 1/16-in. The metallographic inspection of the microstructures of the nails showed that the smaller nails were made in the one operation; i.e. both the tapering and the formation were accomplished on the heated rod without reheating. However, in the case of the larger nails, the nail had to be reheated for the tapering after the head had been forged. Most nails were tapered on all four sides of the shank and the shanks were square in cross section; only one group had rounded shanks. Most heads were flat disks, but in one group the heads were pyramids and another group had conic heads. Figure 1 shows the procedure used to produce the pyramidal heads. Obviously, Roman nail making was sophisticated and each nail design was meant for a particular use.

Jan 1, 1999

By G. Kipouros, M. Dadvand, A. Dadvand

"A novel methodology was developed to obtain a 3D porous layer with a high aspect ratio of porosity on a titanium electrode. The porous structure allowed more active material such as hydrous ruthenium oxide to be accommodated during the fabrication of the supercapacitor, resulting in an exceptionally high capacitance per surface area. The electrode demonstrated a remarkably high capacitance of 4,800 mF/cm2. The porous layer was composed of functionalized nanoparticles of TiO2 organized in a perfect 3D hexagonal close-packed array that resulted in a highly porous 3D structure. The layer was used as a template to electrolessly deposit a thin layer of silver prior to the electrodeposition of active material. KEYWORDS Capacitance, Porous, Ruthenium, Silver, Supercapacitor, Titanium RÉSUMÉ Une méthodologie innovante a été mise au point afin d’obtenir une couche poreuse tridimensionnelle (3D) affichant un rapport d’aspect élevé en termes de porosité sur une électrode en titane. La structure poreuse permet d’utiliser une matière plus active telle que l’oxyde de ruthénium hydraté durant la fabrication du supercondensateur, ce qui se traduit par une capacité exceptionnellement élevée par surface active. L’électrode affichait une capacité remarquablement élevée de 4 800 mF/cm2. La couche poreuse était composée de nanoparticules fonctionnalisées de dioxyde de titane (TiO2) organisées dans un arrangement regroupé parfaitement hexagonal en 3D, qui a engendré une structure en 3D hautement poreuse. Cette couche a servi de modèle pour le dépôt autocatalytique d’une fine couche d’argent avant l’électrodéposition de la matière active. MOTS CLÉS argent, capacité, poreux, ruthénium, supercondensateur, titaneINTRODUCTION There is a growing demand for integrating compact energy storage elements into electronic circuits due to the miniaturization of electronic circuits, sensors, and actuators, and the increasing importance of portable and wear-able devices incorporating more advanced electronic technologies that operate in controlled or uncontrolled environments to gather, process, store, and communicate information (Deng, Ji, Chen, & Banks, 2011; Beidaghi & Wang, 2012; Chen, Ramachandran, Mani, & Saraswathi, 2014). The manufacturing of compact energy storage elements needs to be compatible with the electronic circuit microfabrication processes. Recently, interest in integrating miniaturized supercapacitors into electronic circuits has increased due to their high charge–discharge rate and long operating life; however, ultra-high power miniaturized supercapacitors suffer from low energy density, hence requiring significant enhancement in their energy density for various applications (Deng et al., 2011; Beidaghi & Wang, 2012; Chen et al., 2014)."

Jan 1, 2019

By D. Mills, W. J. Brantina

"Mechanical and magnetic characteristics of ferromagnetic materials were investigated by a pulsed ultra-sonic technique. Two instruments, the Ultrasonic Attenuation Comparator (Sperry) and the standard type Reflectoscope (Sperry) were used for measurements of the attenuation of the ultrasonic pulse. The effects of elastic tensile and compressive stresses on the attenuation of annealed and cold worked material are described. In addition, the effects of plastic de-formation, relaxation and aging processes and different ultrasonic test frequencies are reported. The results for Armco iron, SAE 1020 steel, SAE 4340 steel and AISI 420 stainless steel are shown. Under the test conditions, the attenuation was found to be largely a sum of two components; a ""dislocation"" component associated with the losses accompanying the oscillations of dislocation line segments and a ""ferromagnetic"" component associated with the microeddy currents generated by magnetic domain wall oscillations. Either of these components might be dominant depending on the nature of the particular specimen and the test conditions. Finally, the possibilities of using ultrasonics in residual stress determinations, in fatigue studies and in the study of the ductile-brittle transition in ferrous materials, are briefly discussed."

Jan 1, 1960

By Long Han, Beijing General Research Institute of Mining and Metallurgy, Yu Xie, Yunhai Zhang, Yangge Zhu, University of Science and Technology Beijing, Yanbo Shang, Xingrong Zhang

"The first-principles method was employed to study the adsorption of hydroxyl calcium (CaOH+) and hydroxyl (OH-) on hematite and quartz surfaces. The calculation results suggested that OH- preferred to interact with the active Fe sites on the hematite surface, whereas OH- adsorbed on the quartz surface by weak hydrogen bond. Though CaOH+ could easily adsorb on the hematite and quartz surfaces by the formation of Ca-O bond, the covalence formed on the quartz surface was apparently stronger than that on the hematite surface, meaning a stronger and more stable adsorption. CaOH+ adsorbed on quartz surface was mainly through the interaction of O-2p and Ca-3d states, and this interaction on hematite surface was weaker.INTRODUCTIONIron Increase and Silicon Reduction Technology (Yu & Duan, 2002) of hematite is mainly through the reverse flotation (silica is floated away from the iron concentrate). There are two ways to achieve this (Houot, 1983). One is to collect quartz by cationic collector directly; the other is to activate quartz by lime and then collect it by anionic collector. There are two main different views with respect to the mechanism of quartz activation: mono-hydroxyl compound theory (Fuerstenau, Rice & Somasundaran, 1965; Fuerstenau & Palmer, 1976) and surface hydroxyl precipitation theory (Hu & Wang, 1988; Wang & Hu, 1990). The former indicated the formation of the mono-hydroxyl complex is one of the two criteria of quartz flotation. The later theory, on the other hand, suggested that surface precipitation is the adsorption of active species of metallic ion on quartz surface. However, most of those researches are based on the solution chemistry of flotation and little is done at the microscopic level.In this paper, by the help of first-principles calculations, the adsorption models, bonding conditions, Mulliken charge populations and adsorption energies of hydroxyl and calcium hydroxyl ions (OH- and CaOH+) on hematite (001) and quartz (100) surfaces were investigated to find out the lime activation of quartz at atomic level, which is significant for the researches of quartz activation theoretically and practically."

Jan 1, 2016

By Hector Monette

"AFTER SPENDING a lifetime in the mining industry it is normal that one should be concerned with the future of his profession, especially if he is directly responsible for the education and formation of future mining engineers. It is not necessary to insist on the importance of mining for Canada and for the entire world to prove the necessity of the Mining Engineer. A statement was made by Zay Jeffries, former vicepresident of General Electric Co., and here I quote: ""Even though minerals without man are of no moment, man would not be man as we know him without minerals ... ""minerals are as essential to the life of social man as food is to man himself"". This certainly expresses magnificently the purpose of the mining profession. These are the reasons why I have accepted to present my views on the future of the Mining Engineer. If I express some concern it is not because I feel that there is any danger for the profession to disappear; men will always respond to a challenge and this can be found in the extraction of minerals as well as in any other field of human endeavour. However, the first big question concerns the competitive position of Canada in the world of mining. To be made available to Canadians and to the rest of the world, all this tremendous potential mineral wealth that our country has been so generously endowed with by nature must be gained from the earth's crust at a competitive cost. Otherwise it will never become ore and will have no value. Let us not forget that although minerals are discovered, mines are not found but are made. So let us be more efficient mine makers. To accomplish this end, it is the duty of the different responsible organizations at all levels - be they governmental, para-governmental, public or private institutions - to do their utmost to assure the profitable development of our mineral wealth. The University has an all-important role to play in preparing all the specialists required by this intricate machine that mining is. All the different disciplines of engineering, health, social and -managerial sciences are needed for the good functioning of the mining industry. Although they are all essential, some will play a more important role as a member of the structure. In this discussion it is the role of the most important member, the mining engineer, who is actually responsible for the extraction of the minerals from the earth's crust that must be established. From this we will then be able to analyse his responsibilities and try to suggest the mining engineering program most suitable to prepare this engineer for his future role."

Jan 1, 1972

By John S. Stevenson

Zeballos mining camp is on the west coast of Vancouver island; 195 nautical miles northwest from Victoria.; The spectacularly rich gold-bearing veins that made Zeballos an important; gold camp were found early in 1934. Small pockets of very coarse; gold had been found earlier under large boulders at the mouth of Spud; creek; and in the autumn of 1933 rich gold-quartz float was found near the; mouth of the creek. The rocky beds of the steep creeks entering Spud creek; were searched for its source and as a result the veins on the White Star property; were found. The Goldfield vein on the Spud Valley property was discovered; in 1935; and the No. 1 vein on the Privateer in 1936. In the general; prospecting activity that quickly followed; other veins were found; not; only in Spud creek but in other creeks draining into Zeballos river.

Jan 1, 1954