Search Documents

By O. Worku, J. H. Masliyah, Z. A. Zhou

ABSTRACT The viscosity of concentrated kaolinite or illite clay in aqueous suspensions was measured in the presence and absence of a small amount of montmorillonite (<1 wt%). To avoid solids settling and to increase the sensitivity of the suspension viscosity measurements, solids concentrations higher than 38 wt% were used. The pH of the suspensions and the concentration of calcium and bicarbonate ions were found to significantly impact the viscosity of the clay suspensions. The results showed a significant increase in the viscosity of kaolinite suspensions with the addition of as low as 0.25 wt% of montmorillonite on a solids weight basis. In addition to illustrating the role of water chemistry in modifying slurry rheological properties, our study demonstrated that viscosity measurement could be a simple, yet sensitive technique for determining the content of smectite clays, such as montmorillonite, in a complex mix of various types of clay.

Jan 1, 2012

By G. W. Norval, V. G. Papangelakis, G. A. Moldoveanu

Smelting has been the primary method of treatment for refractory copper sulfide concentrates such as enargite (Cu3AsS4), but the pyrometallurgical processing generates elevated levels of volatile arsenic. The present research investigates a novel hydrometallurgical process of oxidative dissolution of enargite at ambient conditions in the presence of chlorine dioxide (ClO2), a very powerful oxidant generated in solution by the reaction between a strong acid (HCl or H2SO4) and sodium chlorite (NaClO2). The effects of initial oxidant concentration, particle size, agitation speed and temperature on dissolution kinetics and copper extraction were investigated. It was found that a stoichiometric ratio of ClO2:Cu3AsS4 = 9:1 were needed to completely and congruently dissolve the mineral with fast kinetics (<15 minutes) under ambient temperature. The dissolution extent (metal extraction) increases with increasing ClO2 concentration and decreasing particle size of solids, but is not influenced by temperature or agitation speed.

Jan 1, 2014

By J. M. Wolverton

CONSIDERABLE interest has always been taken in Safety-First and First Aid at the Sullivan mine. Even during the early days of development, Safety-First committees periodically held meetings, while lectures in first aid were given to any employees interested in the work. In 1929, a Safety Department was organized, and all accident-prevention and first-aid work was put in charge of a full-time Safety Engineer. An extensive programme has gradually been developed, the value of which can best be indicated by the reduction of the accident rate from 18.4 shifts lost per 1,000 shifts worked for non-fatal accidents and two fatalities for 1927, to 3.24 shifts lost per 1,000 shifts worked and no fatalities for 1936. SUPERVISION All work connected with accident prevention or first aid is under the jurisdiction of a central committee, known as the Accident Prevention Committee, which meets regularly once a month. It consists of all superintendents, department heads, foremen, and shift bosses, and is presided over by the Safety Engineer. At these meetings, the accident records of the previous month are reviewed and all accidents carefully analyzed and discussed. All proposed changes in the safety rules or in the accident tprevention programme are taken up and passed upon. Complaints or suggestions from the Safety-First Committee and the Employees Co-operative Committee, dealing with safety, are discussed and passed upon or a subcommittee is appointed to investigate and take any action found advisable. The question of underground ventilation and dust control, which recently has become a very important problem, always receives considerable attention.

Jan 1, 1937

By S. Ross, M. Mayhew

"Kirkland Lake Gold introduced battery equipped vehicles (BEVs) at the Macassa Mine in 2011. The fleet of underground BEV haulage trucks and loaders has grown over the years to over 30 units, the world’s largest, currently handling approximately 80% of the daily production tonnage. The inflow and outflow of air occur through a limited number of relatively small openings, which limits the air volume delivered to the underground workings. In addition to improving air quality, the reduced heat load generated by the BEV (when compared to diesel equipment) had a significant positive impact in the workplace. The use of BEV for material handling has enabled increases in production that would not have been possible using diesel equipment.INTRODUCTIONMacassa mine was developed as a track-drift access mine, with the most recent shaft (#3) sunk in 1986. A new mining complex, the South Mine Complex (SMC) was discovered below the 5025 foot elevation south of traditional mining areas, and the majority of mining now occurs in the SMC. The discovery of that zone has led to an internal ramp which is used to access the SMC and haul ore to #3 shaft.The amount of airflow that can be moved through the mine is limited by the existing infrastructure to surface. This amount was recently increased to near its practical maximum from 118 CMS (250 kCFM) to 151 CMS (320 kCFM).Both diesel and electric equipment are used at Macassa. Tethered Load-Haul-Dump Machines (LHDs) have been replaced with Battery Electric LHDs, due to their increased mobility and depth of the mine. Battery trucks continue to replace locomotives to transport both ore and waste to the shaft, as mining has transitioned from tracked levels to trackless level and haulage has transitioned from horizontal levels to an inclined ramp.EQUIPMENT FLEET AT MACASSAMost of the primary material movers utilized at Macassa Mine are battery operated. As the mine goes deeper the battery technology will continue to be critical to the success of the operations. With over 300,000 hours of proven operation success, the battery technology and equipment will continue to be a major part of Macassa’s future."

Jan 1, 2019

"Introduction The first documentary record of coal nurung on Vancouver Island was that of the Hudson Bay Company operations in the Suquash area in 1836. Between 1836 and 1862, the Hudson Bay Company mined some 65,000 tonnes from this Suquash field and the Nanaimo coal fields discovered in 1851. However, systematic mining of coal did not take place until the Hudson Bay Company holdings were sold to the Vancouver Coal Company in 1861, and a rival company under Robert Dunsmuir was established in 1869. These two interests under various organizational names and jointly as the Canadian Collieries (D) Ltd. (1928) developed and exploited the coal seams of the Nanaimo and Comox Basins from 1852 to 1966. Because of the proximity of the coal outcrops to tidewater, the coal was readily marketed to ocean-going and coastal ships for fuel. However, during the turn of the century the main market was to meet the demand of the developing cities along the west coast of Canada and the United States for residential and commercial heating. Island-based copper smelters and brick factories, and the coming of the railroads motivated by steam engines increased the demand. This economic success of the industry continued until 1922 when a peak production of over 1,750,000 tonnes was reached. Following 1922 labour unrest in the industry, which affected the certainty of supply, and the availability of alternatives in the form of California petroleum and mainland coal combined to cause a rapid and steady decline in the demand for Island coal. In spite of post-and pre-wartime prosperities the trend could not be reversed. Serious coal mining phased out in the Nanaimo area in 1939 and in the Comox area in 1967. puring the 114 years in which the industry flourished over 75 million tonnes of coal were mined from more than 30 mines and a minimum of ten new mining communities were established on Vancouver Island."

Jan 1, 1985

By Nelson Lawrence

An Electrical Risk Management/Inspection Program has been designed specifically for the mining sector in order to provide electrical code expertise and systemic gaps in electrical systems. Goals include improved safety and productivity, reduced injuries and help to enable businesses to better comply with the electrical codes and regulations that govern them. The Electrical Risk Management/Inspection Program is now recognized by some of the world?s largest mining organizations. Since June, 2001 these electrical safety advisory services have been available to underground and surface mine sites throughout Ontario and are now offered throughout Canada and around the globe. This program is also currently being applied to review new electrical installations for mine construction projects thus improving the safety and reliability of mine site electrical systems.

May 1, 2006

By P. V. Golde, R. A. Poole, G. R. Baiden

"INCO is committed to proceed into the next century using automation and robotics to achieve safety and productivity goals necessary to enhance its competitive position. Stobie Mine, decades old, is the first of its mines to change from labour-intensive to automationassisted techniques. This paper is a synopsis of the progress made during the transition period including overviews of some of the projects as well as some of the difficulties in the assimilation of the technology. BackgroundThe ObjectiveThis paper is an update on remote control and LHD automation installation at Stobie mine. The communications system installed at the mine and the ability to remotely control underground equipment from surface is reviewed (Poole et al., 1996, 1997). It discusses some of the experiences and processes required to further the concept to consolidate the operation of multiple machines under a single operator. It considers the communications systems requirements and their focuses, particularly on the development of systems for the tele-operation of LHDs and drilling machines from surface."

Jan 1, 1998

By George E. Cole

"It is a truism that the metals, and particularly the precious metals tend to monopolize the attention of those interested £n the mineral industry. This is a tendency to be mildly, but actively and continuously combatted if we are to have a well-rounded mineral development." There are in the province of Ontario a number of industries centred about the non-metallic minerals. Too little is heard of the part these play in our industrial life. It is with the intention of showing what the gypsum industry is doing in Ontario that this paper is written. The writer lays no claim to any originality in the discussion and merely offers some material in an endeavour to assist in bringing about that &apos;well-rounded mineral development&apos; sought for Ontario. M. Y. Williams in his "The Silurian Geology and Faunas of Ontario Peninsula and Manitoulin and Adjacent Islands"1 in discussing the industries dependent on the Silurian rocks of south-western Ontario points out that "the splendidly ordered gypsum mine at Caledonia, formerly owned by the Alabastine Company of Paris, and now owned by the Ontario Gypsum Company, is a revelation to the average man, who disconnects mining entirely with this part of Ontario". This region is better known as one of the richest and most thickly settled agricultural areas in Canada.

Jan 1, 1925

By James S. Redpath

"AbstractThis paper is an attempt. to outline the present status of underground mining contracting in Canada, and to present certain facts concerning the writing and administration of underground mining contracts which, hopefully, may be useful to those intending to engage a mining contractor . The paper is based on the author' s experience as a contractor and also as a consulting engineer advising others in the purchase of contractors' services.HistoryIN THE early days of mining contracting in Canada, the contractor was primarily a labour contractor. He was expected to bring a good crew of men that normally followed him, and to perform certain work under his own direct supervision. The owner usually looked after all other details including financing, payrolls, withholding taxes, etc , computing and paying the contractor his profit. In the pre-World-War II years, most work was done on this basis.Over the years, the contractor was called on to supply more in the way of services, and the present-day situation evolved.Labour contracts are still used, but now the contractor is expected to carry out his own administration. Most contracts now call for the supply of special tooling required to do the work. In most cases, some, if not all, supplies are the contractor 's responsibility and , in a growing number of cases, the contractor is responsible for such items as design and surveying. The ultimate in this direction is the execution of projects on a turnkey basis. Under this system , the contractor carries the project to a stage where it is turned over fully operational to the owner."

Jan 1, 1977

By C. D. Williams

The following paper deals with some of the aspects of the law as it relates to the oil and gas industry in the Province of Alberta, but it should be stated here that consideration of this large subject will be confined to discussion of only those laws, rules, and regulations which affect actual exploratory operations. The paper will not touch on those branches of the law which deal with such matters as income tax, customs, and other kind red subjects which are of a highly technical nature and which are more properly the field of the specialist. Generally speaking, any system of law consists of certain major components. There must be, firstly, a national authority capable of ensuring the existence of the state itself and of maintaining the stability and continuity of its institutions; secondly, a philosophy of government covering the relationship of the state to the individual and of the individuals to one another; thirdly, a body of law to effect the purposes of the philosophical principles; and, fourthly, a judiciary to arbitrate any disputes that may arise from such relationships. All of these components and the system itself are, of course, subject to a varying degree of modification with the changing times and with the influence upon them of other systems of law. Now. while it is true to say that all systems of law comprise these similar basic features, it is apparent that the end result of any two systems of law in their impact upon the individual may be quite different.

Jan 1, 1951

By J. R. Johanson, A. W. Jenike

"A solid flows out of a bin provided that the outlet is sufficiently large so that stable obstructions to flow do not develop. The geometry and surface finish of a bin and the construction of the feeder determine the type of flow pattern which then develops within the bin. The pattern, in turn, affects the uniformity and consistency of the stream, segregation, caking, degradation, live capacity and the action of level measuring devices.In most bins now in operation, material flows toward the feeder through a channel which forms within the stationary solid. This is referred to as funnel flow. If the hopper of the bin is sufficiently steep and smooth and the feeder capable of drawing material across the whole area of the outlet, all the solid flows whenever the feeder is in operation; this is referred to as mass flow. Mass-flow bins are usually far superior to funnel-flow bins; their initial cost is also usually higher.The paper describes the design criteria used in deter-mining the minimum bin outlet needed for flow and the bin geometry needed for mass flow."

Jan 1, 1970

By M. I. Kalashnikova, Y. M. Shneerson, E. E. Zhmarin, Y. V. Degtiarev, E. M. Vigdorchik

Separation of a magnetic fraction from nickel concentrate following matte flotation, and its treatment in a separate circuit enable reduces precious metals losses. The magnetic fraction is treated in two stages of oxidative leaching: atmospheric and pressure leaching. A study of the atmospheric stage, using mathematical modelling, is described in this paper. The mathematical model and experimental data were used to carry out industrial process calculations. The model enabled extrapolation of the results of batch laboratory test to industrial-scale continuous processing and the selection of optimal process conditions and large-scale equipment. In December 2004, commercial oxidative leaching tests were performed on the magnetic fraction at the Severonickel Plant (Monchegorsk, Russia). A comparative analysis of the mathematical modelling results and the actual process parameters is presented.

Jan 1, 2005

By H. E. Miard

"IntroductionIT HAS BEEN SAID, with good reason, that the future of the coal mining industry, in our mountainous regions at least, depends on ability to extend operations successfully to depths greater than those reached until now. However, at many points, Nature has given definite hints that trespassing there could be fraught with very un-pleasant possibilities, unless the intruder be governed by a series of rigidly observed principles. In the coal mines of British Columbia, so far, bumps have taken place only at the Coal Creek colliery, but there they gave ample evidence of the extent to which they can hamper underground operations. Some of these manifestations have also been experienced at the McGillivray Creek colliery, in Alberta, at Carbonado, in Washington, and at Sunnyside, in Utah.Cognate phenomena, known as 'air blasts', have been experienced also in some deep metalliferous mines in British Columbia. Such occurrences were responsible for three fatal accidents at the Le Roi and War Eagle mines, near Rossland, in 1916 and 1917.In more or less disturbed coal fields, another form of stress release, equally detrimental, has been still more generally experienced than have been the bumps. Coal outbursts have taken place at Morrissey and Coal Creek, in the Crow's Nest Pass district, and at Cassidy, South Wellington, and the Nanaimo Reserve colliery, on Vancouver island. Manifestations of this kind have been made the subject of intensive study in European countries where they occurred on a really impressive scale, which must not be construed as meaning that some of our own outbursts did not approach a comparable magnitude."

Jan 1, 1953

By H. A. Wilson

Introduction Salt (sodium chloride) occurs naturally either in the solid state as rock salt or in solution as a component of natural brines. It is the major saline constituent of sea water, which contains about 4 percent salt-roughly 164 million tons, or enough to meet world salt demands for five years, per cubic mile. The great rock salt deposits of the world are generally regarded as having been formed by the evaporation of sea water over long periods of rime in wholly, partially, or periodically cut-off bays of ancient oceans. History and Occurrence of Salt in Canada We can speak today of the vastness of Canada&apos;s salt resources, but it was not always so. Settlement of our Atlantic seaboard and the Sr. Lawrence valley began in earnest in the early 1600&apos;s. The first small commercial salt works in Canada did not come into operation until 1866. Thus, for some two and a half centuries, the inhabitants of this growing country were entirely dependent on foreign sources for every pound of salt they consumed. The record shows that from at !east 1800 onward, the need for a domestic salt industry was clearly recognized by the governments of the day. It was during the Western Ontario oil-boom of 1866 that the initial discovery of rock salt in Canada was made, not far from Goderich, at a depth of 1,000 feet. A salt company was promptly organized, and with their operations there began the gradual and still uncompleted conquest of the Canadian salt market by the Canadian salt industry. Over the next thirty years many holes were drilled into the Salina formation both in Ontario and Michigan, and encountered rock salt. A vast salt-basin was disclosed, approximately outlined, and given the name Ontario-Michigan Salt Basin. The Ontario portion of the basin extends over at least 3,500 square miles, is met with at a depth varying between 800 and 1,600 feet, and has a thickness of 50 to 250 feet. No attempt has ever been made, so far as we know, to calculate the total salt reserves of this basin, but the minimum indicated in the Ontario portion by the figures just cited is just under thirty-five cubic miles. The specific gravity of rock salt is 2.2. From these data, those so inclined may calculate the tonnage.

Jan 1, 1947

By L. C. Galloway, P. M. Tiley

"Some progress has already been made in defining the parameters which will determine the performance of a guidance system in a mine shaft. Very little information is available, however, to help designers or operators predict the effects of varying these parameters in new or existing installations.The experience we have gained from monitoring a variety of installations has led to the development of a model which simulates the motion of a conveyance as it moves through a mineshaft, restrained by fixed guides.This paper presents a general analysis of the performance of the guidance system used in several installations, as well as a detailed description of the problem encountered at one mine and the steps taken to solve it.IntroductionOur company has investigated in some depth the problems that arise in the guidance of mine hoist conveyances.We have a telemetering accelerometer which we obtained to test mine hoist brakes. Frequently, during brake tests, the mine owners request us to use this instrument to measure the lateral motion of the conveyance ""to check guide alignment"". We have made such tests in shafts that have guide s of different kinds, including wooden guides, steel rail s and tubular steel guides. From these tests, we have gained some valuable information about guidance systems.In a well-aligned guidance system that is designed within common and well-known practice, the conveyance will experience very little shock most of the time. However, on rare occasions, shocks up to .5 g will occur. That is, the conveyance exerts a force of up to half its loaded weight on the guide. If the guide slips or is damaged by this force, it will be misaligned for future trips and become the cause of future shocks. In time, the whole guidance system can become misaligned."

Jan 1, 1982

By L. C. Galloway, P. M. Tiley

"Some progress has already been made in defining the parameters which will determine the performance of a guidance system in a mine shaft. Very little information is available, however, to help designers or operators predict the effects of varying these parameters in new or existing installations.The experience we have gained from monitoring a variety of installations has led to the development of a model which simulates the motion of a conveyance as it moves through a mineshaft, restrained by fixed guides.This paper presents a general analysis of the performance of the guidance system used in several installations, as well as a detailed description of the problem encountered at one mine and the steps taken to solve it.IntroductionOur company has investigated in some depth the problems that arise in the guidance of mine hoist conveyances.We have a telemetering accelerometer which we obtained to test mine hoist brakes. Frequently, during brake tests, the mine owners request us to use this instrument to measure the lateral motion of the conveyance ""to check guide alignment"". We have made such tests in shafts that have guide s of different kinds, including wooden guides, steel rail s and tubular steel guides. From these tests, we have gained some valuable information about guidance systems.In a well-aligned guidance system that is designed within common and well-known practice, the conveyance will experience very little shock most of the time. However, on rare occasions, shocks up to .5 g will occur. That is, the conveyance exerts a force of up to half its loaded weight on the guide. If the guide slips or is damaged by this force, it will be misaligned for future trips and become the cause of future shocks. In time, the whole guidance system can become misaligned."

Jan 1, 1982

By G. Kachaniwsky, M. Bédard

"The Noranda Continuous Smelting Process at the Home smelter was commissioned in March 1973. The ability of the process to handle a wide variety of feed materials and a steady stream of technical innovations in recent decades has served to maintain the Home as an efficient and versatile custom smelter. This paper reviews recent technological development and capabilities in areas such as sampling and preparation of secondary and complex materials, as well as the smelting and related environmental control issues. Future trends and improvements are also addressed.IntroductionThe Noranda Home smelter commenced operations in 1927. It was originally designed to treat 910 tonnes per day of copper concentrates and ores coming from the new Home mine site. In the 19305, the company opened its doors to other mines in northwestern Quebec. Treatment of feed materials on a custom basis has, therefore, always been an important factor in the operation of the Home smelter. Throughout the years, the Home gradually increased its custom smelting capacity, while maintaining its production from the Home mine. By the early 1950s, 65% of the materials processed was from outside customers, and by 1974, this figure had increased to more than 85% . With the closure of the Home mine in 1976, the company extended its smelting operations beyond ore and concentrate, and began to treat more scrap metals and residues rich in copper and precious metal content.Corresponding with the ever-changing pattern of feed sources, the Home smelter has adopted technological improvements to meet new and challenging business conditions. The technology of the original smelter of 1927has been completely replaced over the years in the quest for improvement. One of these major changes occurred in 1973 with the start-up of the Noranda Process Reactor. This extremely efficient smelting system has been exploited to treat a wide variety of copper and precious metal (PM) containing custom materials. This paper reviews recent developments and improvements achieved at the Home smelter, in the receiving, sampling and treatments of copper and PM scrap and secondaries, with particular emphasis on the development of new technology and equipment in complex feed materials treatment."

Jan 1, 1991

By Fred W. Snow

THE mines of the Consolidated Copper and Sulphur Company, consisting of the Eust1s, the Albert, and the Capel mines, are situated w Ascot township, Quebec, about ten miles southeast of Sherbrooke, on the main line of the Quebec Central railway. Of these mines, only the Eustis is now producing, and it has been operated almost continuously for the past seventy years. Mining methods have been improved in recent years but are still old fashioned when compared with those employed in more modern and up-to-date mines. The ore is of milling grade and is mined for its copper and sulphur con-tent. Silver is present in small quantity, together with a trace of gold. The ore is mined by the shrinkage stope method. Pillars are frequently left as supports for the hanging-wall to prevent serious dilution of the ore and are sometimes recovered after the ore is drawn from the stope. Occasionally, small blacks of ore in close proximity to the shaft are mined by a cut-and-fill method. HISTORY ALBERT AND CAPEL MINES: The Albert and the Capel mines, originally known as the Capelton mine, were discovered in 1863 by George Capel (1). By the end of 1866 the Albert shaft had been sunk to a depth of 121 feet on an incline of about 30 degrees where a vein five feet thick was encountered. In 1879, these mines passed into the hands of G. H. Nichols and Company, by whom they were operated practically continuously until 1907. When mining operations ceased in that year, the shafts had reached depths on the incline of approximately 2,300 feet and 1,000 feet, respectively. These mines have been allowed to cave and fill with water and have been inaccessible for many years.

Jan 1, 1936

By Brian G. Pewsey

Located in the northern part of the Province of British Columbia, the Cassiar Mine started development of its asbestos orebody in 1952, and is currently producing 105.000 tons of asbestos fibre annually. The townsite is nestled in a beautiful valley and supplies more than average facilities. The fibre is shipped to more than 40 countries and is used in many industrial products.

Jan 1, 1978

By K. Swedburg, M. Samuels

"The expansion of the concentrator at New Gold’s New Afton copper-gold mine in British Columbia, Canada, completed in 2015, included an increase in the required retention time of the cleaning circuit. On site pilot testing of a Woodgrove Staged Flotation Reactor (SFR) had shown that a high grade copper concentrate would be produced with excellent recovery. The SFR was selected rather than conventional tank cell technology based on the much smaller footprint (which rendered a separate and expensive building extension unnecessary), high concentrate grades demonstrated in testing, and the lower energy requirement. Three SFRs, each capable of taking a nominal feed of 700 cubic meters per hour were installed and commissioned 10 months after the receipt of order. The SFRs operate in series and all of the cells produce a final concentrate typically grading 32% Cu, while the overall SFR stage recovery averages 55%. The tailings from the SFRs are treated in the original conventional three-stage cleaner circuit where the remaining values are recovered in a concentrate grading 28% Cu. Design production was achieved within days of the initial start-up of the SFR circuit.INTRODUCTIONThe New Afton concentrator, located near Kamloops, British Columbia, Canada processes a copper-gold ore with a designed head grade of 0.96% Cu, 0.72 g/tonne Au, and 2.22 g/t Ag.The New Afton Mine is a block cave mining operation. Ore is undercut from the bottom up and removed at the extraction level from a grid of draw points. Ore is trammed to the ore passes by underground loader and dropped to a haulage level for transport by trucks to the gyratory crusher. From the crusher, the ore is conveyed to the mill via a 4.5 kilometre long conveyor system. Block caving was chosen for the New Afton deposit because the underground infrastructure could be built below the historical open pit of the Afton Mine (a previous operation of Teck Resources) and this method is favorable to large-scale low-cost mining.The New Afton deposit is a copper-gold, alkalic porphyry system. Hypogene mineralization is characterized by discontinuous copper sulphide veinlets and disseminations, principally chalcopyrite and minor bornite, along with pyrite as the second most dominant sulphide. Gold particles vary in size from 5 µm to 40 µm and occur as native gold and electrum, associated mostly with the chalcopyrite grains and never with the pyrite. In some instances, a second alteration phase has resulted in the copper sulphides being replaced by tennantite-tetrahedrite locally and along faults that transect the mineralized body. The design head grade of arsenic is 244 PPM, although the presence of tennantite is inconsistent and can vary from trace levels to 15% of the total copper. No arsenopyrite is present in the hypogene ores. Supergene mineralization, consisting of native copper with accessory chalcocite occurs in minor amounts along faults and highly oxidized near-surface portions of the deposit."

Jan 1, 2016