Search Documents

By Mohammad Reza Khalesi, Ruhollah Rezazadeh, Mohsen Izadi Yazdan Abadi, Mahmoud Abdollahy

"The rotary vacuum drum filter (RVDF) is widely used for dewatering in mining industrial. In general, different parameters have influence in the solid-liquid separation such as: solid percent, level of vacuum, particle size distribution, filter cloth and chemical additives. These parameters can influence on some variables such as cake moisture, throughput and filter cloth life time. The aim of this study is to propose some chemical additives to improve the rate of filtration and decrease cake moisture of Gol-E Gohar iron ore concentrate by using laboratory scale bottom feed vacuum filter and suggest a filter cloth with long life time (more than 400 hours). Effect of particle size distribution on filtration investigated in large scale by measuring the thickness of cake and cake moisture.Increasing molecular weight of anionic flocculant lead to increases throughput but cake moisture increases too; While the filter aid increases throughput and decreases cake moisture simultaneously; the combination of them show different behavior. TSS and filter cloth life time have directly relation with material and type of filter cloth weave. Depending to type of feed, two polyester and polypropylene filter cloth are suggested. More over twill and satin weave have the best results. To prove the laboratory results some industrial tests performed in Gol-E Gohar hematite iron ore concentrate plant.INTRODUCTION“The process of grinding and classification involves the use of large quantities of water. The separation of solids from liquids is usually achieved by gravity sedimentation in thickeners. For fine particles this is a slow process. In general, 75–80% of the water can be separated and removed by thickeners. For further water removal, filters are used where in excess of 90% of the water can be removed” (Gupta, 2006).“Many types of filters are available, which are broadly classified here as vacuum, pressure, precoat and depth filters. Each classification contains a number of sub-processes. A category of filter that uses vacuum induced driving forces and semipermeable media to facilitate the separation of solids from suspension. While pressure differences across the filter are limited to less than 85 KPa (usually 75 KPa), most units are capable of processing a wide range of feed materials in a continuous manner” (Rushton, 2008)."

Jan 1, 2016

By J. P. Morgan, D. B. Stewart

"AbstractLoad-haul-dump machines equipped with. a torque converter and hydraulic pumps have been field tested by means of an engine monitoring instrumentation package. It was found that owing to parasitic losses in the ancillaries and drivetrain, maximum available useable pourer may peak at less than full engine speed. Simple reduction of engine speed may save 15 to 25 percent on fuel consumption, with no significant loss of available power. On some machines, speed reduction will require modification of the torque converter . The cost of this modification, when necessary , would be offset by reductions in exhaust emissions, ventilation requirements, fuel consumption , heat, noise and hydraulic system maintenance, and by increased life of rotating components and filters and machine availability.IntroductionTHE CANADIAN EXPLOSIVES ATMOSPHERES LABORATORY, in conjunction with Deutz Canada Limited, has designed, constructed and field tested a portable instrumentation package. This package monitors diesel engine performance in underground mining machinery by continuously recording engine speed and volumetric fuel delivery. During tests designed to determine the engine load and speed conditions for the various segments which constitute actual underground operation of a Deutz F6L 714-powered 4-yard load-haul-dump machine, it was discovered that an unexpectedly large percentage of the engine power was required to overcome the ancillaries and drivetrain drag (1). That this large component of engine power is functionally related to engine speed rather than the operator's needs was verified by repeat tests of the used 4-yard machine and by testing of a new 5-yard machine powered by a Deutz F 8L 714."

Jan 1, 1977

By J. S. Fox

"Pyroclastic rocks are useful guides to volcanic centers due to the tendency of their fragments to increase in size and volume toward the source vent. The felsic rocks of these centers can be the prime hosts of base metal deposits in the Precambrian Shield; their sub-volcanic equivalents are often the focus of porphyry copper mineralization in the Cordillera. Quantitative mapping of pyroclastic rocks has not yet developed into a routine prospecting tool in Canada, however, possibly due to the cumbersome nature of existing manual techniques and their limitation to structurally simple terrains.A rapid pyroclastic mapping method has been developed whereby the field geologist acquires only a down-plunge outcrop photograph, a record of the fragmental deformation ellipsoid and a record of some descriptive features from each station. Mean fragment size and volume percent are obtained later in the laboratory from a photo-enlargement: by means of a digital analyzer. A computer program uses the strain parameters to 'undeform' the field measurements and obtains genetic information from the descriptive data. Results can be superimposed on a geologic map, with values for each station being represented by a dot of a specified diameter corresponding to the size or volume percentile range to which the value belongs.Control traverses were run over the pyroclastic rocks surrounding the Anderson Lake mine and the Flin Flon South main shaft in northern Manitoba. In both locations, the mapping has delineated regular increasing trends in mean size and volume per cent toward the head frame."

Jan 1, 1977

By J. D. Allan

"IntroductionThe purpose of this paper is to present a general picture of the Lynn Lake nickel area of northern Manitoba. The geology of the area will not be discussed in great detail, nor will the mining op; rations presently being conducted. Both subjects will be treated briefly and, in addition, mention will be made of some of the problems encountered in mapping in the area. some of the questions which still remain unanswered, methods of prospecting that have been applied and the future possibilities of the area.For present purposes, the Lynn Lake area will be considered as extending from west of Lynn lake to east of Barrington lake. Thus, more correctly, it should be termed the Lynn Lake-Barrington Lake area. It comprises five 15-minute map-areas, or a total of 800 square miles, in a block 47 miles east-west and 17 miles north-south.Lynn lake itself is about 120 miles north of Sherridon, Manitoba, the closes t rail terminal. The area is part of the Granville Lake sheet which was mapped by the Geological Survey of Canada in 1932, 1933, and 1935, the results being published in Summary Report 1933. Part C, and as Maps 343A and 344A on a scale of four miles to o.ne inch. In 1940, the McVeigh Lake area was mapped by the Geological Survey of Canada on a scale of 1,500 feet to 1 inch and a map was issued in 1945."

Jan 1, 1950

By L. Voisin, K. Yamaguchi, D. G. Mendoza, K. Ltagaki

The behavior of arsenic and antimony in the Cu-0 system was thermodynamically investigated to understand their elimination during a blister-making stage in copper smelting. Firstly, the phase relations in a miscibility gap composed of the liquid slag and copper phases in the Cu-0-As and Cu-0-Sb systems at 1523 K were established by a quenching technique. It was found that arsenic and antimony distributed preferentially into the slag phase in the miscibility gap. Secondly, the activities of arsenic and antimony in the miscibility gap of these systems were determined at 1523 K by using a double Knudsen cell - mass spectrometer method. It was clarified that the activity of arsenic in the copper and slag phases showed the negative deviation from ideality while that of antimony in the copper phase a slightly positive deviation. These data obtained in this study suggest a possibility to eliminate arsenic and antimony by means of over-blowing in a converter after discharging the slag.

Jan 1, 2007

By W. R. Gunter

"INTRODUCTIONThis article documents the current non-metallic mineral s resources of Manitoba (Fig. I), and makes comparisons with currently producing deposits in North America and elsewhere in the world. Industrial minerals may lack the glamour of gold, silver or the base metals, but they contributed approximately 20070 to the value of Manitoba's raw materials, and even out-performed our petroleum industry, except during the oil boom of the early eighties (Fig. 2). Values per tonne of industrial commodities can be as high or higher than for base metal ores. Commodity prices (Canadian), listed in the February 1988 issue of Industrial Minerals magazine, are: talc $202.00 - $306.00, sillimanite $427.00; kaolin $69.00 - $270.00; garnet $175.00 - $250.00; and mica $405.00 - $540.00. The prices are converted to Canadian dollars using the prevailing exchange rates of February I, 1988. Some commodities are not sold by weight. Building stone, for example, is sold by the cubic foot. An average rough granite block, 4 ft by 4 ft by 8 ft, is worth approximately $2000 sitting on the quarry 1100r in southeastern Manitoba (Fig. 3).Thus, not all rocks that do not contain sulphides are worthless. Some may be extracted more profitably than either the base or precious-metal bearing varieties.Industrial Mineral CommoditiesThe commodities available in Manitoba are described in two categories: (1) those already in production that have additional development or expansion potential, and (2) those not in production logical information available at this time.Current Industrial Mineral ProductionThe commodities described herein are currently in commercial production in Manitoba (Fig. 4). These mineral products also have good market expansion potential provided additional geological and market research is conducted. The use of company names in reference to sundry products and locations should not be interpreted as specific endorsement by the Government of Manitoba. The numbers following the commodity name refer to Figure 1. that have good development potential on the basis of geo-"

Jan 1, 1989

By Nicholas J. Welham

"The effect of extended ball milling has been studied for two industrial processes: (1) the processing of metal sulphide concentrates; and (2) the carbothermic reduction of ilmenite to synthetic rutile. The plant concentrates were a gold ore with 128 g/t Au of which 8% was non-refractory and a zinc concentrate with copper impurities.The gold concentrate showed complete dissolution of the gold bearing minerals after milling giving almost complete gold liberation. The zinc concentrate showed almost all of the sulphides had solubilized leaving the gangue and elemental sulphur. A study of pure pyrite and arsenopyrite shows that selective dissolution should be possible by a simple leaching process directly after milling.The milling of ilmenite and coal together results in a temperature decrease of 150°C in the subsequent carbothermic reduction of ilmenite, in addition to improving both the rate of reaction and the selectivity of reduction to rutile. IntroductionAlmost all mineral processing plants use mills for the size reduction of particles prior to physical and chemical processing. When continuing beyond size reduction the energy transferred causes deformation, breakage and realloying of particles giving a steady-state particle size. The breaking also causes increasing damage to the crystal structure by formation of smaller grains giving an increasing number of grain boundaries and increasing crystalline defects due to deformation. The increasing number of grain boundaries and defects leads to increased reactivity, which can be seen directly by a reaction within the mill, or indirectly, via a decrease in the subsequent annealing temperature required for reaction."

Jan 1, 1997

By H. R. Shakeri, R. Mayer, M. J. Worswick, A. Rahem

The current focus of research and development in transportation industry is to use lightweight materials such as aluminium alloys for more structural components. In this regard, maintaining safety of the passenger and vehicle is the most important; therefore crashworthiness of components made of lightweight materials must be evaluated prior to sizable application of these materials. The focus of the present study is to understand failure and damage mechanisms during the axial crushing of aluminium tubes made of A1Mg3.5Mn alloy of 2 and 3.5 mm thickness. Due mainly to complexity of the crushed tubes, a microstructural approach is considered. In this study optical, stereo as well as scanning electron microscopy techniques have been used to study damage and failure mechanisms in these types of tubes, which are essential energy absorbing components in passenger vehicles.

Jan 1, 2006

By E. C. W. Perryman

BEFORE describing the methods used for fabricating uranium into various shapes and sizes it is necessary to illustrate briefly the unusual conditions under which uranium has to operate when used as a fuel element in a reactor. During reactor operation, for every fission that occurs two atoms of intensely radioactive fission products are produced together with two or three neutrons. The neutrons that are ejected possess several m.e.v. of energy and when one of them strikes an atomic nucleus, that atom acquires up to 105 e.v. of kinetic energy. This is large enough to displace the atom from its lattice position and send it shooting through the crystal, displacing other atoms out of their lattice positions. The net result is that a large number of vacancies and interstitial atoms are formed within the crystal lattice which sometimes have profound effects on the physical and mechanical properties of the material in question.

Jan 1, 1957

By C. S. Liao, S. L. Wang, C. H. Yan, F. X. Cheng

A significant development in the theory of countercurrent extraction will be presented in this article. A new term in countercurrent extraction process analysis, "Adjacent Stage Impurity Ratio" (ASIR), is proposed, and its expression is deduced. Furthermore, based on the term together with mass balance and extraction equilibrium, the conditions where a given countercurrent extraction separation operation can have minimum amounts of both extracting solvent and scrubbing agent solution can be estimated, and the equations of the two minimum amounts can be deduced. It was found that the equations for a two-component separation using a single aqueous or organic feed are exactly the same as they appeared in the theory initially established in the 1970s. Unlike its earlier version, the present derivation does not involve feed-stage-composition hypothesis, and also has the advantage of dealing with a double-feed system where both aqueous and organic feeds are simultaneously employed whereas the earlier theory can only analyze a separation using a single aqueous or organic feed.

Jan 1, 2014

By S. Kaiman

This paper describes flotation test work conducted over the past several years at the Mines Branch, Ottawa, on the radioactive quartz-pebble conglomerate ores of the Elliot Lake area of Ontario. The purpose of this work has been to produce a uranium flotation concentrate for sub-sequent leaching operations. The results of earlier investigations are summarized and correlated with the results of mineralogical studies of the ores and flotation products. The results of recent pilot-plant investigations by flotation, as well as by gravity concentration followed by flotation of the gravity tailings, are given. The principal collector used for uranium flotation was a tall oil fatty acid, and the indicated total cost of all reagents ranged from 21 to 31 cents per ton of ore treated.

Jan 1, 1966

By X. -G. Chen, E. M. Elgallad

Direct chill (DC) cast ingot plates of 2xxx alloys have been increasingly used for large mold applications in the plastics and automotive industries. A novel heat treatment practice for Al-3%Cu-1%Mg DC cast ingot plates has been developed, involving solution treatment, furnace cooling to the desired aging temperature and holding for appropriate time at the aging temperature. The mechanical properties of the plates were studied for different combinations of aging temperature and time, using hardness measurements and tensile testing. The evolution of the strengthening precipitates was investigated under different cooling rates corresponding to cold water quenching, still-air cooling and furnace cooling, using electrical conductivity measurements. The results showed that by applying the novel heat treatment, the cast ingot plates could provide a wide range of combinations of strength and ductility satisfying the design specifications of large molds. This, in turn, offers a practical solution for the fabrication of extremely large DC cast plates combining between good mechanical properties and low levels of residual stress using the shortest possible heat treating cycle.

Jan 1, 2015

By M. H. MacLeod

"IntroductionTHE ORE PASS raise system at the H.B. mine as contracted by the Patrick Harrison Company consisted of two raises 6 ft. by 10 ft. in section •at 60 degrees to the horizontal. No. 88-88 raise, the longer of the two, was a straight raise 690 feet long, with access only from the bottom. In addition, this raise had two branch knuckle-backs only one of which was driven by. the Patrick Harrison Company. The other, known as 88-89 raise, was 540 feet long with knuckle-backs at 280 feet and 410 feet. Its access, also, was from the bottom (see Figure 1)."

Jan 1, 1954

"Syncrude Canada Ltd. operates one of the largest surface mines in the world. The mining operation has two distinct phases: (1) the removal of the overburden, utilizing trucks and shovels; and (2) the mining of oilsand with drag lines and bucketwheels. Both phases combined move approximately 330 000 BCM per day.In support of current production demands and to provide a contingent oi/sand source, Syncrude has developed an Auxiliary Production System (APS) supported by the truck and shovel operation. This system utilizes oilsand sources within the existing mine area on an as-needed basis.The recent increased capabilities of the processing plant to handle a larger volume of oilsand has increased the reliance of the APS system. To facilitate the increased capacity, an auxiliary mine was developed external to the Base Mine operation with a production capacity of4.7 MBCM of oilsand per year.Development of the Northwest Auxiliary Pit began in January 1990, with the first cubic metre of oilsand taken to the plant in June, 1990. The Auxiliary Pit, as designed, has a total ore reserve of 68 MBCM of oi/sand."

Jan 1, 1993

By J. Shahabpour

"Abstract - Breccias with angular and rounded clasts of a late-mineralization, ""barren"" hornblende porphyry dike set within a comminuted matrix consisting of rock fragments and quartz, cemented by quartz and K-feldspar of hydrothermal origin is observed in diamond drill cores from the Sar Cheshmeh porphyry copper deposit. Studies of age relationship between vein types, phyllic-altered clasts and the breccia groundmass suggest that the brecciation is a late event. The breccia clasts record evidence of hydrothermal reaction between the clasts and fluids responsible for the brecciation.Formation of bornite, in the breccia clasts of the originally barren hornblende porphyry dike, and in the breccia matrix, along with the scarcity of bornite in the Sar Cheshmeh deposit itself suggest involvement of fluids which are later and of different composition from the fluids responsible for the known mineralization at Sar Cheshmeh. These later fluids may be related to a later plutonic event and suggest the possibility of a later, and concealed deposit."

Jan 1, 1994

By Jamie N. Burdeski, Susan E. Hartfield-Wünsch

Aluminum sheet use has been steadily increasing in the automotive industry to achieve mass reduction and improve fuel economy. One significant manufacturing challenge for aluminum sheet implementation is the reduced formability compared to the steel alloys it replaces. This paper includes friction results from the draw bead simulator (DBS), twist compression (TCT) and strip draw (SDT) tests, for two oil based lubricants and four hot melt lubricants. Formability testing was done with the same lubricants and materials, testing in pure stretch with a hemispherical punch, and in draw with a breadpan shaped die.

Jan 1, 2015

While this paper is directed towards the ?Bellambie? type of rope attachment, the principles can be applied to any brand of rope fitting however, it is a only a broad outline and the specific installation and maintenance procedures can be obtained from the attachment supplier. The types of attachment to be discussed are:- ?Thimble Type rope cappel ?Wedge Type cappel ?WRC Rope Clamp ? (Rope Glands) ??Hoist and Balance Rope Sockets In each case, the assembly and stripping (disassembly) plus the basic maintenance procedures is briefly described. A guide for Risk Assessment is also included but because of his familiarity with the installation, the end-user is in the best position to draft the final version.

May 1, 2003

By Robert Dickson

Princess colliery is operated by Old Sydney Collieries, Limited, a direct descendant of the General Mining Association of London, England, which, in the first quarter of the nineteenth century, pioneered in coal mining in Nova Scotia. The coal worked is a 5 ft. 6 in. seam known generally through the Sydney coalfield as the Harbour seam but referred to locally as the Sydney Main. Entry is made by shafts, 680 feet deep, sunk in 1871 on a headland forming the northern entrance to Sydney harbour. From them extend the main roadways of the colliery, a distance of 700 feet to the shore line and a further distance of 14,700 feet in submarine areas to a total length of 15,400 feet. It was the first colliery in Nova Scotia designed to work submarine areas. Lateral development extends across a frontage of 16,000 feet and the submarine area from which the coal has been extracted is slightly over 6 square miles. There yet remains sufficient territory ahead of the workings to assure a future life to this colliery estimated at over 80 years at the current rate of production. In this area the seam dips at 6 to 7 per cent and face workings have reached a depth of 1,690 feet below the sea level. Until 1923 extraction of the coal was by room-and-pillar, followed by the drawing of the pillars. At that date the superincumbent strata had reached a thickness of 1,400 feet, resulting in heavy weighting on the roof and severe side pressure on the coal ribs. In combination with a soft, heaving pavement this created a set of conditions involving great difficulties and expense in keeping open places driven in the solid sufficiently long to permit recovery of the coal in the pillars by methods and equipment then available. The operator was forced to resort to extraction by longwall as the only economical method of winning the coal.

Jan 1, 1948

By Samuel B. Rombeger

The behavior of gold in hydrothermal systems is evaluated as a function of pH and oxygen and sulphur activities at temperatures to 250°C. Under conditions of stability of pyrite and argillic alteration as emblages, gold will be transported as bisulphide complexes. In systems containing significant amounts of arsenic, thioarsenide complexes may be important. Oxidation, dilution and reduction in sulphur activity would cause gold deposition from saturated solutions under these conditions. Gold chloride complexes will predominate under oxidized conditions where hematite or other oxides are stable and depo ition would result from increase in pH and/or reduction . Absorption and coprecipitation are po sible mechanisms of deposition for gold in certain low grade depo it . Low concentrations of gold in the transporting solution combined with the ignificant solubility of gold as bisulphide complexes, sugge t hydrothermal solutions rarely may be saturated with gold and coprecipitation with sulphides may be an important initial depositional process. Recrystallization of the sulphides in the presence of the hydrothermal solution would be re ponsible for release of gold to more table ite . Thi mechani m i supported by the close association of gold with pyrite in many hydrothermal gold deposits.

Jan 1, 1986

By John A. Hansuld

Geochemical dispersion of metals under various environmental conditions is discussed within the frame-work of Eh (oxidation potential) and pH (acidity). In general, two aspects are considered -(1) the oxidation of certain primary sulphides in the outcrop or sub-outcrop environment, and (2) the movement of metals in different dispersion media. Practical applications of each are illustrated by means of exploration case histories representing environmental conditions in the Canadian Shield, the southwestern United States and the Caribbean.

Jan 1, 1966