Search Documents

By G. C. Bateman

THE cause of silicosis and its prevention have held the attention of medical men and mine operators for many years and at the present rime the study of this disease is more than ever to the fore, even though a considerable abatement in the incidence of silicosis has been noted of late. This abatement is due to individual and collective efforts. The Industry is keenly alive to the situation and much research is being carried on. Silica dust is assumed to be a contributing factor in the cause of silicosis. How it acts progressively in the early silicoric is nor fully understood. As the study advances, more effective measures of control may be evolved. At present the Industry has three known methods of reducing the incidence: 1. By thorough X-ray examination of all applicants, with special reference to chest conditions. Those who are considered to be susceptible to the disease are prevented from entering the industry. 2. Thorough ventilation of the mine. 3. Control of tuberculosis in mining centres and removal of miners when first symptoms of tuberculosis become apparent. In 1934, the Ontario Mining Association formed a Committee, known as the Technical Silicosis Research Committee, to study and supervise work on problems related to silicosis. This Committee obtained the full-rime services of a mining engineer to carry our research work at the mines in the Province of Ontario. The Ontario Mining Association has also provided funds for the purpose of carrying on research work along pathological and biological lines. This work is being done in the Department of Medical Research of the University of Toronto, in the Banting Institute, under the supervision of Sir Frederick Banting. The Silicosis Committee work in full cooperation with the doctors in the Banting Institute and provide material from the mines for the it use.

Jan 1, 1936

By Waldbillig. D.

A baseline of the poisoning effect of hydrogen sulfide (H2S) fuel impurities on solid oxide fuel cell (SOFC) anodes was developed using polarization testing. After the baseline behaviour was characterized, tests to study the effect of various H2S concentrations on the rate and amount of cell voltage degradation and recovery were performed. Attempts were made to improve the rate and amount of recovery by various methods. Testing was very reproducible, but significant electrochemical performance degradation was seen after all H2S poisoning tests even at an H2S concentration of 0.1 ppm. Degradation is initially quite rapid, but after a period of time the rate of degradation levels off. After poisoning was complete, the H2S flow was stopped and the cells were allowed to recover. Some recovery was seen after poisoning, but cell performance was never fully recovered.

Jan 1, 2005

By S. Makni, G. Gagnon, F. Couët, C. Rochefort

"Comminution represents a significant part of mineral processing plant operating costs. Yet, autogenous (AG) or semi-autogenous grinding mills (SAG) are difficult to control because of disturbances like feed size distribution and rock hardness. AMIRA, within project GeMIII, developed a comminution index from laboratory crusher data. The index correlated with the Bond ball mill work index and with the A×b parameter. The present work extends the use of crusher data as a grindability indicator to real-time industrial applications. The aim is to improve comminution operation using online hardness estimation. Because the operational work index is proportional to the ore work index, rock hardness variations can be estimated from the feed and product size distributions, the throughput, and the power draw of a crusher. Real-time estimation of rock hardness can help understand the dynamic behavior of AG and SAG mills. Multivariate time series were analyzed to understand the impact of hardness on a SAG operation. Results showed that the estimated hardness influences the SAG operation and its throughput. Moreover, non-linear dimension reduction was used to ease the process visualisation and search for potential control strategies. In the future, online hardness measurements should also impact the understanding of comminution circuits and improve their operation.INTRODUCTIONThe variability in hardness, and the feed size distribution, are two of the main disturbances affecting comminution circuits (Sbarbaro & del Vilar, 2010). Size distribution can be measured by imagebased granulometry systems such as WipFrag (Maerz, Palangio, & Franklin, 1996), or by 3D vision systems when the fines are difficult to discriminate by 2D segmentation (Faucher, Makni, Gagnon, Lavoie, & Roberge, 2015).There are few examples of online hardness measurements. One example was the work of Casali et al. (2001) who developed a hardness indicator. The ore grindability soft sensor used the fraction of each lithological class in the ore, as determined by image analysis, to predict the work index of the material. The model was developed using a moving window with a width of 12 months and trends were shown over many years with one data point per month."

Jan 1, 2016

By S. Maleksaeedi

On-site evaluation of strength using hardness is common for different materials. The lack of such relation for aluminum alloys has always been felt. In this work, a finite element analysis of plastic deformation and its distribution in Brinell hardness testing is presented. The analysis has been performed for different strength levels of aluminum alloys. By utilizing the Von Mises equivalent strain in hardness, it is tried to derive a correlation between hardness and strength values for the alloys under consideration. The derived correlation is verified using the experimental values available in literature.

Jan 1, 2004

By H. Wotruba, K. Neubert

Dual-energy X-ray transmission (DE-XRT) imaging is known from safety luggage inspections at airports. The use of DE-XRT technology for sorting applications in the primary raw materials industry has been the subject of numerous investigations. Beside other metal ores, X-ray transmission sorting is already used for the preconcentration of tungsten ore, gold ore and coal. The applicability of DE-XRT sorting is limited to ore types where differences in metal concentrations are measurable, based on an interpretation of X-ray images. Metal contents in particles occur in large varieties in terms of concentration, grain sizes, spatial distribution and mineralogy and therefore influence the X-ray absorption. As a result, each ore has to be tested individually for its suitability for DE-XRT sorting. The objective of current research at the Department of Mineral Processing (AMR) at RWTH Aachen University is to assess parameters influencing the detectability of rare earth oxides. Two approaches were followed: (1) Practical test work, based on artificial ore samples of defined compositions and (2) Computer-based simulation of absorption features of identical particle compositions. In total, more than 300 artificial samples of various compositions and metal grades were produced and X-ray images from DE-XRT sorting were analyzed. Results from the DE-XRT sensor were put into correlation with metal grades and particle sizes, to analyze influences and limits on the detectability of rare earth oxides. In addition, a new approach was tested in which the X-ray absorption of particles of various compositions was determined based on a Monte Carlo (MCNP) simulation. During the simulation, similar compositions, as used for the artificial samples, were tested and the X-ray absorption behavior during DE-XRT sorting was determined. A comparison of results from both approaches is used to assess the applicability of the MCNP-simulation for the prediction of the X-ray attenuation behavior during DE-XRT sorting.

Jan 1, 2016

By Thomas Hauquin, Olivier Deck, Yann Gunzburger

"In this study, 2D numerical modeling of a room-and-pillar mine is conducted along with the calculation of all terms of the mechanical energy balance. Simulations of different geometrical and geomechanical configurations are performed in order to investigate the conditions that favor a high seismic energy release (instability) during the excavation (removal) of one single pillar. At first, classical stressstrain simulations enable us to estimate the elastic and quasi-static response of the mine. Then, owing to the implementation of new functions in the modeling code, the seismic energy released when the pillar is removed is calculated. The obtained values are found to be in agreement with those calculated analytically using a modified energy balance based on the works by Cook (1967) and Salamon (1984).It is shown that the mine’s proneness to release large amounts of seismic energy, after sudden removal of one single pillar, mainly depends on three parameters: the initial extraction ratio of the mine, the depth of the exploited seam and the Young’s modulus of the surrounding rock mass compared to that of the ore. Moreover, it is pointed out that the magnitude of the seismic energy can be greater than that of the stored elastic energy, meaning that the dynamic (seismic) transient stresses should not be neglected when compared to the quasi-static stresses, particularly when trying to prevent the risk of rockburst and collapse in underground mines."

Jan 1, 2015

By Charles W. Villiers

AS is well known, there are large and valuable deposits of coal in British Columbia, both on the mainland and on Vancouver island. These deposits are widely distributed over the Province. The chief sources of supply on the mainland are found in the Fernie and Princeton-Nicola districts and on Vancouver island in the Comox and Nanaimo districts. The coals range from a very high quality bituminous coal to lignite. On the Upper Skeena river there is said to be a very large deposit of anthracite or semi-anthracite, but this field has not been developed. Coal was first discovered in British Columbia on the north end of Vancouver island in the year 1835, but it was not until 1852 that coal mining was seriously undertaken by the Hudson's Bay Company at Nanaimo, where mining has been carried on continuously ever since that date. The production of coal in the Province continued to increase until the year 1910, when the annual output reached its peak at 3,100,000 tons and a total of 7,800 men were employed in the industry. Since 1910, the production has dropped steadily until, in 1934, only 1,347,000 tons of coal were produced and less than 3,000 men were employed. This continued decrease in production has in no way been caused by lack of coal reserves. It has been due entirely to curtailment of markets. I do not propose to discuss coal mining practice in British Columbia, where we have all sorts of mining conditions, including submarine mining. There is no lack of coal supplies for either industrial or domestic purposes, nor is there likely to be any shortage of coal in the Province for many generations. We have our mining troubles, which increase the cost of production, but there are no insuperable difficulties to prevent the extraction of a large and increasing supply of coal. Our main difficulty-in fact our only serious difficulty-is to find a market for our output, and we must consider means which can be evolved not only to conserve our existing markets but also to expand them, at any rate within the boundaries of Canada. I will therefore confine my remarks chiefly to the all-important factor of Markets for our coal.

Jan 1, 1936

By W. R. McQuarry, M. E. Wilson

"The structural relations of the ore deposits of the Staclacona mine are of considerable interest, for they not only illustrate the effect of a change in competence of the wall-rock, but also the effect of either the convergence together of two faults, or a change in the clip of a fault, or both of these factors, on ore deposition.The mine is in claim M.L. 1818 near the eastern end of Pelletier lake and lies about 2 miles south of the town of Rouyn. The Company was organized in 1926 to explore claims in Rouyn, Dufresnoy, and Beauchastel townships, but attention was directed mainly to those in Rouyn. Underground work began in 1928 with the sinking of the main shaft to a depth of 300 feet. Except for 1930 and 1931, the mine has been in operation continuously since that time. Production, which began in 1936, up to the end of 1946 has amounted to 1,381,422 tons of ore from which gold and silver having a total value of $7,861,860 were recovered. The average grade of the ore milled in 1946 was $6.68.GEOLOGYThe rocks in which the Stadacona ore deposits occur are mainly volcanics of the (Keewatin) Abitibi series intruded here and there by numerous dykes, sills, or masses of diorite. Single dykes of olivine diabase and lamprophyre are also present in the property and are intersected in the mine workings. The volcanic rocks are part of a wide belt of northward dipping lavas and pyroclastic rocks, having a thickness of over 16,000 feet, that extend from the east-west trending belt of Timiskaming sediments on the south northward to the Horne Creek fault and form the south limb of a large syncline. The volcanic rocks within the property consist of numerous, east-west trending, northward dipping flows of andesite and a few flows of rhyolite interbedded with rhyolite ruff and agglomerate. The angle of dip throughout most of the property is 60° to 80°N., but in the main cross-cut on the 850- and 975-foot levels stratification in rhyolite tuff was noted dipping 35°N. The tuff at this point lies above an intrusive mass of diorite and it is probable that the change in dip results from the way in which the tuff and agglomerate have been thrust aside by the intrusive."

Jan 1, 1954

By Nawshad Haque, Leanne Smith, Hal Aral, Joseph Cho, Warren Bruckard

"Water availability is one of the principal parameters in determining the feasibility of mining projects in arid and semi-arid regions. The volumetric water footprint (VWF) of a conceptual model of a copper flotation plant was found to be 2.45 kL/t Cu ore, compared with an actual measurement reported in the literature of 2.72 kL/t Cu ore. The flowsheet considered included mineral processing stages such as crushing, screening, grinding, classification, separation, flotation, thickening and filtration. The effect of a number of variables on the VWF was evaluated, including solid/liquid ratio, feed mass flowrate, ore loss, water loss, moisture content of ore, ore grade and water recycling. The use of seawater with recycling provided the most environmental and economic advantage among several scenarios evaluated. The study assumed a price of $1/kL freshwater, $4/kL for transport over a 200 km distance at 2,000 m altitude and $4/kL for water treatment. The water related cost of the desalinated seawater use scenario was A$493/t Cu concentrate, while the water related costs of fresh water and blended water scenarios were A$308/t and A$268/t Cu concentrate, respectively. The water related cost (fresh water scenario) accounted for 44% to 49% of the entire mining and processing costs that included drilling, blasting, loading, hauling, crushing, grinding and concentrating. The total overall cost was A$435/t Cu concentrate for the seawater with recycling, compared to A$451/t Cu concentrate for the fresh water with recycling case.INTRODUCTIONReducing the water footprint (WFP) by utilising alternative water sources has been a focus of mining projects due to increasing concerns about water scarcity and growing energy costs. The global mining industry can expect to experience fresh water shortages in the future, and saline or hyper-saline water may be the only available water source to process minerals in arid regions. Extensive studies on alternative water sources (e.g. seawater, desalinated seawater, blended water) and the reuse of process water have recently been conducted (Moreno, Aral, Cuevas, Monardes, Adaro, Norgate & Bruckard, 2011; Aral, Mead, Cuevas, Davey & Bruckard, 2010). Such studies provide sustainable and economic strategies for mines and concentrators in the arid or semi-arid regions of the world such as in Chile, Peru, Indonesia, and Portugal. More work, however, is needed to confirm water consumption data for different base metal flowsheets and use this data to develop water models that can lead to reduced WFPs and more sustainable water usage in the mining industry."

Jan 1, 2016

By P. Rosario

"Current industry practice for HPGR assessment and sizing relies on conducting a series of tests using pilot-scale machines with roll diameters of 700 mm to 1000 mm. Substantial amounts of sample are required for such pilot test programs, typically 1 to 10 tonnes of the sample is needed depending on the level of study and complexity of the resource. Collection of large quantities of representative samples during the early stage development is challenging and expensive, thus significantly hinders the HPGR technology from being incorporated into early-stage designs. A robust and reliable laboratory test is therefore needed to allow a fair consideration of HPGR for early stage projects. With support from the Canadian Mineral Industry Research Organization (CAMIRO), the NBK Institute of Mining Engineering at the University of British Columbia (UBC) developed a suite of Piston Press bench-scale tests that correlated to pilot and full scale HPGR operating information (Davaanyam, 2015; Davaanyam et al, 2015; McClintock, 2018). The Piston Press Tests (PPTs) are capable of assessing the HPGR technology at the scoping, pre-economic analysis (PEA), and pre-feasibility (PFS) stages of project development. This paper will briefly describe the theory on which the PPTs are based, and then presents a case study conducted for a copper deposit to show how the PPTs are being used for scoping and pre-feasibility level studies. Specifically, the PPTs are being used to provide information for preliminary sizing and selection of an HPGR and to assess the effect of ore variability on HPGR performance. The results are also applied to developing HPGR circuit designs and can be incorporated in simulation so that optimum design parameters can be selected.INTRODUCTION It is widely accepted that high pressure grinding rolls (HPGRs) offer a viable energy-efficient solution for the modern comminution flowsheet design. Table 1 summarizes selected examples of HPGR applications in the hard rock mining industry. The main benefits of HPGRs are energy savings which leads to lower operating costs, and its stable operating characteristics that can better cope with variations in ore hardness when compared to the conventional SAG mill-based comminution circuits."

Jan 1, 2019

By I. Ciabatti

Inorganic salts of hexavalent iron (ferrate (VI)) are versatile reagents for water and industrial effluent treatment because of the strong oxidising effect of the ferrate ion (FeO42-) and the well-known coagulation properties of the resulting ferric ion. Among other applications, ferrate can effectively remove arsenic, cyanide and phenols from industrial effluents. Furthermore, ferrate salts can be prepared from ferrous sulphate, a common byproduct of the steel and titanium industries, and possibly from other iron wastes. Notwithstanding their many potential advantages, the industrial-scale application of ferrate salts, such as potassium ferrate (K2FeO4), for effluent treatment has been hindered by the difficulties inherent in their synthesis and stabilisation. Within a project co-funded by the European Commission, the large-scale synthesis of stabilised potassium ferrate was realised through a new synthesis process, and different applications of the resulting ferrate to effluent and wastewater treatment are under investigation. This paper reports the results of the application of stabilised potassium ferrate for the purification of textile effluents. Laboratory and pilot-scale tests were carried out and the performance of the ferrate was compared to that of chemicals currently used in wastewater treatment. According to these experiments, potassium ferrate is a promising reagent for an effective treatment of textile and other industrial effluents.

Jan 1, 2006

By P. J. Finnis

This paper describes the use of wire rope on open-pit mining equipment, giving specifications and examples of the performance achieved. Installation methods are also discussed, making the paper of considerable practical use to mine operators.

Jan 1, 1973

By J-F. Magnan, M-A. Thibault, R. Boulianne, C. Gauthier, J-P. Gagné, G. Dufour

During the production of aluminium in smelters, the anodes used in electrolysis cells have to be replaced frequently. Anode butts are usually placed on anode trays for transportation and cooling, a practice during which Hydrogen Fluoride (HF) is emitted in large quantities. Covers developed in 2000 by Alcoa Deschambault to fit on the anodes trays were implemented, resulting in significant reductions of HF emissions. However, the covers are expensive to maintain and use short-life consumable parts. In January 2004, STAS and Alcoa decided to develop a more efficient design of cover, with lower maintenance costs and no need for consumable materials (like soft cushions). This paper presents a summary of the work performed to develop the new design as well as a summary of the test results.

Jan 1, 2006

By J. Olaf Sund

"THE November issue of the Bulletin carried in it ""Origin of the New Bruns1viclc Gypsum Deposits"" by J. Olaf Sund. This paper was a digested account of a Master's thesis at the University of New Brunswick which was a very useful compendium of information of gyp-sum in New Brunswick. It was a warded the President' s Gold .Medal and the First Prize in the Graduates' Section of the Students' Essay Competition. The present writer presents his congratulations to the winner of the competition. At the same time he must comment on the use of certain terms and on certain conclusions presented in the paper.The term ""unconformable"" has been used in several places in the paper to describe the relationship of gypsum to anhydrite in various deposits in New Brunswick in a sense which is quite alien to the accepted meaning. It has long been known tl1at the gypsum at the surface or near the surface in deposits in the Atlantic Provinces has come from hydration of anhydrite by surface and ground waters. The gyp-sum must be looked upon then as an alteration or even a weathering product. It cannot in this sense be called ""unconformable"" and thus arguments using the word in the accepted sense are invalid."

Jan 1, 1960

By F. J. West

This paper deals with Jones & Laughlin Steel Corporation's new Adams mine, near Kirkland Lake, Ontario. After a brief discussion of ore structure, type, reserve tonnages, etc., the main body of the paper discusses the establishment of an open-pit limit based on economic considerations. The method used by J & L to arrive at an economically sound open-pit boundary its outlined fully. Physical limitations to open-pit boundaries are mentioned briefly. The paper concludes with a few remarks on the mining equipment in use and on its productivity

Jan 1, 1966

By A. McEachern

At the Annual Meeting of this society, held in Halifax last year, a paper entitled "Closed System Breathing Apparatus" was read by I. C. Mackie, metallurgist, British Empire Steel Corporation. Coming from such an authority it was most instructive and illuminating. The purpose of the paper was to emphasize the necessity of a full supply of oxygen and the danger of oxygen shortage in the use of rescue breathing apparatus. In connection with this he pointed out: "In times of emergency, when life is at stake, rescue men cannot be restrained from using their utmost endeavor, and unless the apparatus is adequate to meet the heaviest load, the result may be fatal to the wearer. The body's demand for its oxygen requirement is absolutely imperative and must be granted at once. We can do without food for many days and without water for many hours, but we cannot do without full requirements of oxygen even for a few minutes. Furthermore, the victim of oxygen shortage gets practically no warning. He may fall helpless or unconscious before realizing that he is in a serious condition." Hence the necessity for expelling all the nitrogen from the breathing-bag and filling it with pure oxygen; also filling the lungs of the wearer with oxygen before he begins to use the breathing apparatus. This practice is general at all the collieries under the British Empire Steel Corporation.

Jan 1, 1924

By E. H. Mulligan

THE ERRINGTON B-I mine is located on the Errington orebody of Steep Rock Iron Mines, Limited, at Steep Rock Lake, Ontario. In 1946, this orebody entered the shipping lists of the Lake Superior iron ranges as an open-pit operation. During the period 1946 through 1953, the mine produced a total of 9,000,000 tons of iron ?ore. In 1950, as the mine approached the economic limits for open-pit operations, ground was broken for an underground development to exploit the deposit at depth. The mine is designed for an ultimate production of 1,500,000 tons per year by the block-caving system of mining. The initial shaft is 1,200 feet deep and will produce or-e from the 700 and the 900 levels. The 1,100 level will be used as a drainage level and as a haulageway for waste rock, which is hoisted to surface by skip. Ore from the two production levels moves by a system of ?ore passes to a crushing plant located below the 900 horizon and is hoisted from this point to surface by conveyor belt. At the present time, all material handling on the levels is by tramming, but as tram distances increase conveyor haulage will probably be installed. The initial stage of the Errington B-1 development is expected to produce 6,000,000 tons of ore over a period of four years. The second stage will require deepening of the shaft and development of lowe1? production levels. The conveyor hoisting plant will be extended to serve these new levels. We visualize the mining of this orebcdy down to 2,500 feet by these methods.

Jan 1, 1956

By B. Hart, D. J. Miller, J. T. Francis, M. C. Biesinger, Smart. R. St. C.

Diagnosis of the surface chemical factors playing a part in flotation separation of a valuable sulfide phase requires measurement of the hydrophobic and hydrophilic species that are statistically different between the concentrate and tail streams. Time of flight secondary ion mass spectrometry (ToF-SIMS) can be used to identify sufficient particles of a specific mineral phase for reliable statistics determining a mean value for each species with 95% confidence intervals (1). Using the region of interest (ROI) facility in the Tof-SIMS software, a mass spectrum from each particle, at 1-2 monolayer sensitivity, is recorded and stored. This analysis is reported for a chalcopyrite / pyrite / sphalerite mineral mixture conditioned at pH 9 for 20 minutes in order to study transfer of copper from chalcopyrite via solution to the other two mineral surfaces since this mechanism can be responsible for their inadvertent flotation in copper recovery. Analysis from mineral selection based on specific ToF-SIMS signals (eg. Pb, Zn, Cu, Fe, Fe/Cu) indicated no statistical difference in the copper intensities on pyrite and sphalerite after this conditioning. Principal component analysis (PCA) of the ToF-SIMS imaging data identifies combinations of factors strongly correlated (positively or negatively) in images or spectra from mass spectra recorded at each of 256x256 pixels in a selected area of particles. PCA is a better method of selecting minerals due to multi-variable recognition. It has clearly separated a statistical difference in copper intensities between the sphalerite and pyrite phases. The method has been extended to samples from an operating plant again with excellent phase recognition and diagnostic surface chemistry.

Jan 1, 2004

By Douglas H. Silvey

"The historical transformations in fire -resistant conveyor belt compositions in the past 20 years have been influenced by factors of material cost, changing flame and burn test requirements, material replacements, adhesion and oil resistance considerations, increased responsibility and legal liability. Specifically, this has resulted in a swing from neoprene-cotton belts to S.B.R. blends and synthetic fibre carcasses, and tighter quality control and documentation of test data.Flame dynamics are discussed and the function and performance of the multiple types of flame-resistant additives in the flame front are presented. Specific flame and burn test requirements are described. The belt manufacturers' requirements and criteria in selecting the types of flame-resistant additives are presented.The author will describe the composition of the types of flame-resistant compounds used in a practical production, the belts that are available on today's mark et and future developments in requirements that may further transform the composition of fire-resistant belts.IntroductionThe historical transformations of conveyor belt compositions in the past two decades have been based on factors common to those leading to changes in man y organic compositional products. These factors are material cost, new materials, the customer' s changing requirements, government regulation s and increased manufacturer' s liability.As a basis for understanding the product, I will provide a brief breakdown of the conveyor belt composite. Figure 1 represents a cross section of a typical belt. A skim rubber coats each fabric ply of the belt carcass and is of a different rubber composition than the outside layer of rubber which forms the cover. This outside cover layer is designed to protect the belt from environmental factors such as heat, oil and abrasion, and other factors involved in the service condition s under which the belt will operate. In the case of fire-retardant belt s, both the skim coat encapsulating the fabric plies and the outer cover must contain sufficient fire retardancy to overcome the contribution to burning of the decomosition products of the fabric."

Jan 1, 1982

By S. E. Malouf, R. Hinse

"The Mineral possibilities of the Chibougamau area were first recognized by Richardson in 1870 and Low in 1885, both of the Geological Survey of Canada. The first record of interest by the Quebec Bureau of Mines is in 1904, when J. Obalski reported on the discovery of copper and asbestos by Peter McKenzie in the previous year. Reports of 1906 and 1907 covered the McKenzie Gold Mine find and other deposits. In 1908 Prof. Dulieux described the quartz vein on Merrill Island and the mineralized zone on the near-by mainland. In 1910 the Chibougamau Railway Commission, though commenting favourably on the possibilities of the area, concluded that a railway was not then warranted.In spite of this, prospecting in the district continued. The main Campbell Chibougamau deposit, the Blake showing on Merrill Island in Dore Lake, was found in 1920, and other discoveries were made soon after. Between 1927 the work of Mawdsley, Retty, and Norman tor the Geological Survey and the Quebec Bureau of Mines stimulated further interest. In 1934 Consolidated Chibougamau Goldfields Ltd., a subsidiary of Consolidated Mining and Smelting Co. of Canada Ltd., acquired the Merrill Island and Cedar Bay holdings of Chibougamau Prospectors Ltd. They embarked on an aggressive campaign, directed essentially at the gold quartz veins at Cedar Bay. Exploration there included a 522-foot shaft, 4,732 feet of drifts and crosscuts, and about 34,000 feet of surface and underground diamond drilling. Thirteen holes were also drilled on the replacement sulphide lens at Merrill Island. Operations were suspended in 1936, as the occurrence was too low grade for development at the existing metal prices and under difficult operating conditions.The completion of the Quebec Bureau of Mines highway from St. Felicien to Chibougamau in 1950 was followed by a project of detailed geological mapping by the Bureau. It also encouraged Campbell Chibou-gamau Mines to acquire the assets of Consolidated Chibougamau Gold-fields and commence a program of surface exploration. Between August 1950 and April 1951, 41,183 feet of diamond drilling was done on the Cedar Bay and Merrill Island holdings. The Blake showing off the west shore of Merrill Island developed at depth into a major orebody. A lease was obtained on adjacent ground from Merrill Island Corporation, and underground work commenced in November 1951. Development at Merrill Island to June 1st, 1955, included a four-compartment shaft to 1,225 feet, with 8 levels at 150-foot intervals, 5,317 feet of raises, 16,709 feet of drifts and crosscuts, 52,514 feet of surface and 96,593 feet of underground diamond drilling."

Jan 1, 1949