Search Documents

By W. Dziurzynski, St. Wasilewski, T. Palka, A. Krach

"Air parameter monitoring systems, regardless of gasometrical protections, provide a significant number of measurement data. The obtained data broadens the knowledge on processes taking place in underground workings and shows the relationships and influence of machines and technological processes on the variability of ventilation parameters in the areas of longwalls. Nowadays, computer simulation methods are increasingly used to reproduce the flow of air and methane mixture in the area of longwalls equipped with shearers. The paper presents the results of a research experiment covering a long-term observation of a longwall area during mining with a shearer using sensors from the mine's monitoring system. Data from sensors for methane concentration, pressure and velocity were used and additional ventilation measurements were taken to determine the parameters characterising the air flow in the area. The influence of different machine cycles in the longwall on the changes of air parameters in the area of the longwall was shown. A numerical model of the ventilation area was developed and the computer program VentZroby was used for the calculations, which allows for the simulation of the process of ventilating the area of the active longwall during the extraction of coal with the use of a shearer and haulage of the run-of-mine. Computer simulation of the influence of the shearer's operation and the methane inflow associated with the distribution of the mixture of air and methane was carried out. The results of the simulation were compared with the data recorded by the monitoring system’s sensors during the measurement experiment. Comparison of the recorded methane concentration courses with the results of a computer simulation of the air and methane flow conditions in the mining area showed changes in the gassiness. INTRODUCTION Studies carried out in the Polish and global mining industry show that methane is an obvious factor in limiting mining production due to the loss of continuity in the operation of longwall complexes in hard coal mines under methane emission hazard (Schatzel et al., 2008). In addition, methane hazards have a significant impact on the safety of the operators of machinery in the longwall. The requirements of Polish regulations and the practice of safe operation of mining longwalls require correct determination of gas concentration, volume flow, as well as pressure and temperature of the flowing air. As part of the research undertaken in the Budryk (Wasilewski, 2010) and Bielszowice (Dziurzynski et al., 2009) mines to assess the methane hazard in the longwalls and workings in the vicinity of the longwall, research experiments were carried out, during which air parameters were recorded by the mine monitoring system and additional testing equipment in different cycles of shearer operation."

Jan 1, 2019

By P. Cleyle, J. H. Masliyah, R. S. Chow, Z. H. Xu, Z. A. Zhou

Bubble nucleation in water under dynamic conditions was investigated using an autoclave at an air saturation pressure of 7 atm. Agitation during air saturation of water was found to be crucial in enhancing tiny bubble formation. More bubbles nucleated on hydrophobic surfaces at a higher agitation rate, due to cavity formation by the more intense hydrodynamic conditions. Flotation recovery of bitumen from oil sands demonstrated a significant role of bubbles nucleated in water: more than 50-170% increase in bitumen recovery from different oil sands was obtained by using air supersaturated than the regular water.

Jan 1, 2009

By A. E. Wraith, J. Protheroe Jones, P. J. Mackey

INTRODUCTION When Victoria became queen in 1837, that technical wonder of the 19th century—electricity— had progressed from being an exciting physical curiosity and was now a field of intense scientific investigation, invention and application. Its role in electrochemistry had been brilliantly quantified by Faraday in 1833–1834, and his earlier discoveries in electro-magnetism were to lay the foundations of electricity generation and the electric motor. In this age of electrical experiment, silver electro-plating emerged as a popular decorative art, at first using batteries to provide the deposition current, superseded by dynamos in the early 1840s. The decorative chemical and electroplating of precious metals was largely pioneered in England by the firm of G.R. Elkington and Co., founded in Birmingham by George Richards Elkington (1801–1865) in 1832, and protected by a series of patents which helped the company establish a leading position in the new field of ‘electrometallurgy’. In the same decade, the technique of electrotyping emerged, the first application of electro- forming by electrolytic deposition. Simultaneously invented by Spenser in England and Jakobi in Russia, but generally claimed for Jakobi, electrotyping involved plating a thick copper layer on to an electrically conducting mould wall embossed or incised with a pattern or profile which would consequently be replicated on the copper deposit—essentially a method of casting by electro-deposition with the mould wall as cathode. Woolrich’s invention of the low voltage magneto-dynamo in 1842 eliminated the need for batteries as a continuous source of deposition power, opening up the possibility of making more massive electroplated deposits, and by the mid-point of Victoria’s reign in 1869, the work of Wilde, Wheatstone and Siemens had produced the self-excited electro-dynamo, capable of higher voltages and yet greater deposition power. In this early Victorian period copper was extracted and refined by methods which had developed step-by-step over many decades. Only relatively rich copper ores containing more than, say, 6% Cu were economically useful, and the final copper product was far from pure. Copper production in Britain was located principally in the Swansea area of South Wales, based upon the ‘Welsh process’ of reverberatory batch smelting and refining, using locally mined coal and ore imported from Cornwall and elsewhere. Silver was an important by-product. Much of the output was exported and South Wales remained a principal supplier to the world copper market until the 1890s. It was here at Pembrey, a few miles west of Llanelli, that a new primary copper smelter was stablished in 1849 under the name Mason and Elkington, arguably to supply the Elkington company’s market for electrotype products.

Jan 1, 2019

By P. R. A. Andrews, R. K. Collings

"There are more than thirty-five deposits or occurrences of celestite in Canada, chiefly in Newfoundland, Nova Scotia, New Brunswick, Ontario and British Columbia. Deposits of economic interest are the Lake Enon and MacRae deposits in the Loch Lomond district of Cape Breton Island, Nova Scotia. Two Cape Breton deposits were operated from 1969 to 1976 by Kaiser Celestite Mining Limited, which supplied an upgraded celestite concentrate to an associated strontium carbonate plant at Point Edward, near Sydney.The MacRae deposit is of current interest because of its possible development for strontium carbonate production using the ""black ash"" process. This process involves chemical leaching, rotary kiln calcining with petroleum coke, washing and treatment with carbon dioxide.Celestite is the basic material used in the manufacture of strontium chemicals, principally strontium oxide, carbonate, nitrate, chromate, chlorate, chloride, sulphide and phosphate. Strontium chemicals, in turn, are used in the manufacture of glass and ceramics, in pyrotechnic devices, in the production of strontium metal and in other metallurgical applications. Recently, strontium ferrites have been introduced into permanent ceramic magnets."

Jan 1, 1991

By Mark Freberg

"IntroductionThis chapter is intended to provide information on the operation and maintenance of several pieces of equipment used in heavy media separation. Most heavy media separation circuits, particularly those involving bath separators can be considered as high maintenance areas. Because of this the efficient operation and maintenance of these circuits is very important if the cost per ton of material treated is to be kept to an acceptable level.Heavy media separation (HMS), is a process used to separate particles of different specific gravities. Under laboratory conditions the ideal way to separate two types of particles which have different specific gravities is to suspend them in a heavy liquid which has a specific gravity between those of the two types of particles. Those particles with the lower specific gravities will float on top of the liquid while the higher specific gravity material will sink to the bottom. Given enough time and a sufficient volume of heavy liquid this process will be essentially insensitive to the sizes of the particles involved.Heavy media separation circuits make use of the same principles described above. The material to be treated is introduced into a mixture of finely ground solids, called media, and water which takes the place of the heavy liquid; the mixture of solids and water is known as medium. The separating force can be either gravity or centrifugal force. The type of solids used as media varies but it is usually a high specific gravity material such as magnetite, galena or ferrosilicon.Heavy media separation is used extensively in the cleaning of coal and to a lesser extent as a preconcentration step in base metal and iron ore operations."

Jan 1, 1989

By Jan Butra

Longstanding mining of copper deposits in the Legnica-Glogow Mining Basin, Poland has accumulated broad experience concerning the impact of geological and mining conditions on seismic and rockburst hazard. Methods of rockburst prevention for deep copper mines have been developed based on gathered data. Methods of rockburst hazard evaluation and rockburst control constitute a set of rockburst prevention measures. Due to their nature and location within the production process, prevention methods can be passive or active. Active methods of rockburst prevention consist of the liquidation of stresses in the areas where they are concentrated through controlled generation of rock-mass tremors and rockburst by blasting works (group extraction blasting, release blasting in the rock mass and pillars able to accumulate the stress, as well as in the roof and floor). Group blasting works as a basic method are very effective in copper mine conditions. Provocation of dynamic events makes it possible to control the timing of their occurrence. In Polish copper mines, all blasting works are made during the absence of miners in the mining fields. Daily distribution of both the number of recorded strong seismic events and volume of energy released, confirm the advisability of using this kind of rockburst hazard prevention. The rockburst hazard prevention methods developed over 40 years of copper deposit extraction are economically reasonable and offer sufficient effectiveness under high rockburst hazard conditions.

Aug 1, 2013

By Robert B. Parsons

"Ontario and Quebec taxpayers will have to dig deeper into their pockets to pay more tax, according to budget papers tabled in these provinces in May 1993. Individuals will be hardest hit, but corporations will also have to ante up in the face of higher rates, reduced deductions, and new taxes.Up, up, and away...Somewhere in the bleak picture of the 1993 Quebec and Ontario budgets, there is a bit of good news for the mining industry.Careful scrutiny reveals:• Ontario will correct a capital tax provision which inadvertently penalizes flow through share issuers;• Quebec's flow-through incentives will be extended to December 31, 1995; and • both Quebec and Ontario will allow deductions for mine site reclamation payments.The industry may also find some comfort in the fact that Ontario's new corporate minimum tax will be profit-based (unlike the federal minimum tax), so that non-producers should not face a liability for this tax. There is some concern though, about Quebec's announcement that the refundable credit mechanism in the Mining Duties Act will be reviewed."

Jan 1, 1993

By H. A. Kishawy, S. Kannan, M. Balazinski

Metal Matrix Composites (MMCs) are new generation engineering materials that possess superior physical and mechanical properties compared to nonreinforced alloys. However, the presence of abrasive ceramic reinforcements in the ductile matrix causes severe tool wear and premature tool failure. Flank wear was found to be the dominant wear mode while the main wear mechanism was abrasion. Analysis of the cutting tools using scanning electron microscopy has shown that both two body and three body abrasion are operational during machining MMCs. A methodology for predicting the tool flank wear progression during bar turning ofMMCs was presented in an earlier paper [1]. In the proposed model, the wear volume due to two body and three body abrasion mechanisms was formulated. Then, the flank wear rate was quantified by considering the tool geometry in 3D turning. The main objective of this paper is to investigate the contribution of two body and three body abrasion towards the tool wear volume during cutting MMCs.

Jan 1, 2006

By F. Doxey

Introduction In order to improve outputs and to reduce or hold mining costs, many attempts have been made to mechanize the getting and loading of coal in the major coal producing countries, and machines of various kinds and sizes have been designed and manufactured. Some of the most important are: Joy Continuous Miner Joy Coal Auger Goodman Mining Machine Lee-Norse Koal-Master Jeffrey Colmol Cardox Hordsecg Recovery Drill German Coal Plough British Coal Plough with agitated blades M. & C. Samson Stripper AB Meco-Moore Cutter Loader Joy Gloucester Getter The three last named are the chief longwall machines in use and the AB Meco-Moore and the Samson Stripper are doing a good job in their respective applications. It is understood that the Gloucester Getter recently installed in a British colliery also shows reasonable promise. It was felt, however, that to meet the conditions of the mines in Nova Scotia, any machine developed must have certain distinctive characteristics. It must: ( 1) Be able to cut and deliver coal in quantity and of the right sizes ( 2) Be easily manoeuvrable ( 3) Be suitable for longwall operations ( 4) Not interfere with timbers already set ( 5) Cut its own stable (6) Work on reasonably heavy gradients

Jan 1, 1951

By Owsiacki. Leo

Both the 8 and A-C ore zones of the Heath Steele Mine contain extensive areas of brecciated ore. This texturally distinct ore type has been tentatively defined as a fragmental or conglomerate massive sulphide. It consists of subangular and round fragments of pyrite up to 30 em in diameter, smaller quartz clasts and chloritized, mineralized, lithic fragments in a faintly banded matrix of pyrrhotite and chalcopyrite. The chalcopyrite is concentrated in the pressure shadows of the fragments and appears to reflect remobilization and recrystallization during a deformation which postdates the formation of the clasts. A generally conformable relationship with the underlying banded pyrite-sphalerite ore, discordancy with the host banded argillites, spatial distribution and similarity to Kuroko ores suggest that the fragmental ore is of primary origin and that breccia formation is probably due to soft-sediment slumping or sliding initiated by volcanic explosions, as hypothesized for similar massive sulphides in various Japanese mines. It is nevertheless recognized that certain structural features in some clasts may result from deformation preceding the formation of the breccia, and at this stage a tectonic origin cannot be completely eliminated.

Jan 1, 1979

By J. -M. Bosgiraud, G. Armand, S. Dewonck, L. Richard-Panot

"The Meuse/Haute-Marne Underground Research Laboratory (URL) is located on the eastern boundary of the Paris Basin. The URL started to be built in 2000 (shaft sinking operations) in the framework of ANDRA’s (French national radioactive waste management agency) research program aimed at determining the feasibility of a reversible deep geological disposal of high-level and intermediate-level long-lived radioactive waste (HLW, IL-LLW). Its underground drifts are used to study the Callovo- Oxfordian claystone layer between 420 m and 550 m in depth.The ongoing research program (started in 2006) following the “Technology Readiness Level” (TRL) Scale is more dedicated to technologies improvement and demonstration issue of the different disposal components, even if characterization and monitoring studies are still ongoing.In rock mechanics, at the main level of the URL (located at 490 m), construction and evolution of disposal cells of different size are studied for HLW and IL-LLW packages. A step by step approach, started in 2006, is carried out based on comparison of HM behavior of parallel drifts excavated/supported by different construction methods. These various configurations give insight of the influence of construction method on the EDZ extent and evolution and on the progressive loading of the support, which are key issues to design the Cigéo disposal drifts and excavations.The concept of disposal cells studied for HLW consists in horizontal steel lined micro-tunnels 80 m long and 70 cm in diameter. Several campaigns of tests have been carried out since 2009 in order to demonstrate the feasibility of excavating such micro-tunnels and study their behavior under different conditions (with and without back filling the annular gap between the rock and the casing, watertight or not casing). A full scale demonstrator representative of the benchmark concept has also been excavated, to study its behaviour under thermal loading with heat produced by electrical heaters."

Jan 1, 2015

By K. Thuro, L. Wilfing, H. Kasling

"In mechanized tunneling, performance prediction is a crucial issue for estimating excavation costs and construction time of a tunnel project. The aim of this work is to compare the calculated parameters by penetration prediction models with the results of penetration tests during excavation by a Tunnel Boring Machine (TBM) at actual tunnel projects. This comparison helps to improve the existing prediction models (Gehring, 1995 and Rostami (Colorado School of Mines), 1997.) and to develop a new, so-called “Alpine Model” (research group ABROCK; Schneider et al., 2012).On-site penetration tests are a common tool to determine performance of a TBM in certain geological environments. During a test, the TBM is operated under defined conditions that allow comparing the results of different projects and machine types. There are two different types of penetration tests in use. The more common type, described by Bruland (1998a), is based on test drives at different thrust levels. The tests in this study are performed as start-stop-tests, meaning that the TBM starts from zero to the maximum possible thrust and reverse with slowly increasing respectively decreasing steps (Frenzel et al., 2012). To gain information about the interaction between TBM and rock mass, a detailed geological documentation including an analysis of the discontinuity pattern and laboratory testing for rock strength characterization are mandatory.Within the last year 16 penetration tests have been performed. The results are thrust- penetration curves (Figure 2) showing that up to a certain penetration rate only crushing occurs (subcritical penetration). From there the desired rock fragmentation process called chipping takes place (Frenzel et al., 2012). These two different fragmentation processes can be described best by a bilinear function as seen in Figure 3. Both, CSM- and Gehring-model, do not fit to the trend of the penetration rates determined during the excavation process as they are using potential or simple linear functions.Another parameter that has to be implemented into the new prediction model is the influence of discontinuities. In case of favorable orientation and spacing, discontinuities reduce the required thrust at same penetration rates. In contrast, unfavorable discontinuity systems can cause blocky faces and hence worse performance than predicted. Besides discontinuities, the toughness of rocks has to be taken into account when predicting the penetration as tough rocks need more energy to obtain complete failure than brittle rocks.Key advantage of these tests in comparison to existing are more data points in less time. By improving respectively extending the existing penetration prediction models with the stated parameters, the penetration prediction for TBMs can be more accurate and also wear calculation can benefit from this approach."

Jan 1, 2015

By Rick J. Chalaturnyk

In Alberta, oil sands bitumen is utilized for synthetic crude oil production by surface mining, bitumen extraction followed by primary (coking) and secondary (catalytic hydrotreating) upgrading processes, or by catalytic hydrocracking and hydrotreating replacing the primary and secondary upgrading processes. Oil sands tailings, composed of water, sands, silt, clay and residual bitumen, is produced as a byproduct of the bitumen extraction process. Several processes have been proposed for the treatment of oil sands tailings, resulting in different recovered water characteristics, consolidation rates and consolidated solid characteristics, which may have effects on the performance of the overall plant operations. A process for the same purpose has been developed by treating the oil sands tailings with CaO lime and CO2 and thickening it using a suitable thickener. In this process a release water of acceptable properties is recovered in a short retention time, which makes it possible to recycle the recovered water, probably after a reconditioning treatment, as warm as possible to improve the thermal efficiency of the extraction process. The paper presents the theory and laboratory results for the CaO and CO2 thickening of low temperature flotation tailings. The water release rates, segregation potential of the thickened underflow and chemistry of the release water are shown and discussed. It is suggested that in using the proposed process, the thickened tailings underflow can be disposed for further consolidation, or combined with the coarse tailings to produce Blended Composite Tailings, corresponding to the Composite Tailings process in the existing hot water extraction plants.

May 1, 2002

By V. W. Shtenko, B. J. Ennis, P. H. Bridge

"The northeastern region of British Columbia contains large quantities of high-quality metallurgical coal. To market the coal, it was necessary to provide the required infrastructure which included rail access. This paper presents the role of the British Columbia Railway in the northeast coal development.In 1976, B.C. Railway undertook to study two main routes, one originating at Chetwynd and the other at Anzac, both located on the main line, north of Prince George. The routes studied are briefly described, detailing the methodology and engineering analysis carried out to permit the selection of a single route that would be the most cost effective, taking into consideration the construction, maintenance and operating costs. The operating parameters, track and grade standards, anticipated tonnage, construction costs and the final route selected are also presented.Pre-engineering analysis and studies of the route selected originating at Anzac, known as Tumbler Ridge Branch Line, and which commenced in 1977, were concluded in 1978. New mapping was developed to a scale of 1:2000 with good vertical and horizontal control. Based on the mapping data, terrain analysis, and designs developed, an estimate of construction costs and schedule of work was developed.Authority to proceed with the final design and construction was provided in December 1980, with the first shipment scheduled for December I, 1983. Final designs of all structures are discussed, including schedules, cost to completion, and control systems utilized. The decision to electrify the Tumbler Ridge Branch Line and related topics are discussed, with a brief description of train operations. The present status of the project is also presented."

Jan 1, 1983

By G. B. Harris

A new process for the recovery of copper and associated base metals from a polymetallic massive sulphide ore is described. The massive sulphide contains copper and especially nickel sulphide in a mineralogical form which negates both good recovery and high grades in concentrates using conventional flotation methods. Flotation concentrate processing and smelting from this ore is therefore probably not an economically viable option. Utilising the properties of high concentration chloride brines, a flow sheet has been developed and tested whereby the recovery of all of the metals and some of the power requirements for the plant itself can be derived from the ore. The new process overcomes the less-amenable-to-flotation ore characteristics, and provides the opportunity of economic processing in remote locations where the dependency on fossil fuels is both a logistical and an economic concern. The Ferguson Lake deposit of Starfield Resources in Nunavut, Canada, is the subject of this paper, which focuses on the leaching and copper recovery unit operations of the proposed flow sheet.

Jan 1, 2007

By L. A. Anestiev

A method based on use of calorimetric data for the determination of solidification kinetic parameters is proposed. The method incorporates recent theories of nucleation and growth and allows modeling heat fluxes observed in calorimetric experiment. Statistically optimal estimations of the kinetic parameters, which include the activation's energies of nucleation and growth, are derived from experimental data by means of nonlinear regression analysis. The method is applicable to pure substances and alloys. The evaluation of the kinetic parameters characterizing solidification of pure Al is used for clarifying and exemplifying the method.

Jan 1, 2004

By L. E. Djingheuzian

"ForewordTHE FOLLOWING excerpt is taken from Fine Grinding Investigations at Lake Shore Mines (C.I.M., Trans., Vol. XLIII, 1940, p. 307):""MacCalman, who has carried out exhaustive testing on the accuracy of screen analysis, makes the following statement in his report, The Accuracy of Sieving Tests, Industrial Chemistry (London, England), Vol. XIV, p. 231:"" 'It will be shown that, as no specific relationship between the sieving value and the various dimensional features of the sieve is evident, though there is an apparent tendency for the sieving value to follow the average aperture size, it is apparently impossible to define the sieving value of a screen from dimensions alone, and the calibration of sieves for important tests on a specific material, whereby the sieving values of these sieves are related to that of an arbitrarily chosen master sieve by correction values, will be recommended."" 'It will be emphasized that these correction values are probably not applicable to other materials, or the same material of different size composition. Sieve users, for important tests or in cases of dispute, will be recommended to calibrate their sieves against a mutually acceptable standard with specified conditions of test, and to recalibrate at intervals' ""."

Jan 1, 1953

By Jason Mewis

Jason Mewis is the founder and president of ENGCOMP, a consulting engineering firm in Saskatoon Saskatchewan focusing on the mining sector. He has over 17 years of experience working on projects for the heavy industrial market in Saskatchewan, as both a Senior Structural Engineer and Project Manager. Jason is an entrepreneur with experience in many areas including estimating, planning, facilitation, and Risk Analysis. He has presented at many seminars and conferences across North America on the subject of Project Risk and and has become recognized for his expertise in this area of project management.

May 1, 2013

By John F. Kearney

Labrador Iron Mines (?LIM?) Schefferville Projects consist of 20 major DSO deposits lying along a 120 km strike length in both the provinces of Newfoundland and Labrador and in Quebec. The town of Schefferville, Quebec lies close to the middle of this 120 km strike. LIM?s various properties comprise twenty different iron ore deposits which were part of the original Iron Ore Company of Canada (?IOC?) direct shipping Schefferville operations conducted from 1954 to 1982 and formed part of the 250 million tons of historical reserves and resources previously identified by IOC. LIM intends to develop all these resources in five separate stages. The first four stages will see the various deposits treated in three beneficiation plants, to be built adjacent to several of the deposits that comprise the Central, South Central and North Central Zones. The final stage is not yet planned but will likely involve a fourth plant. A Feasibility Study has not been completed on any of these Projects. LIM plans the development and mining of the various deposits in separate Stages. It should be noted that only the James and Redmond deposits have been permitted. All other deposits require environmental assessment and permitting. Only the James and Redmond deposits have been subject to detailed mine design. The Houston deposit has had preliminary mine design carried out. All other deposits will require detailed mine design when further geological data is collected and compiled. Detailed metallurgical testwork has been carried out on blue ore from James, Houston, Redmond and Knob deposits and to a more limited extent on yellow and red ores from these deposits. Only limited review work has been carried out on the high-silica blue ores. All of this work will be needed to be complete to confirm the final process routes. Additionally some metallurgical work will be required to be conducted on each of the other deposits to characterize their metallurgical response and to confirm expected recovery levels. Detailed mine design and metallurgical testwork has been carried out on those deposits that will form the basis of production for the initial years but further exploration, testwork and design is required for all the remaining resources. The first plant at Silver Yards and mine construction at James are now complete and initial production is expected in the spring of 2011. Metallurgical testing of the first stage deposits has established that the ore can be successfully upgraded to marketable standards. Based on the current testwork, a program of plant enhancement on the Silver Yards plant is now planned with the objective to increase both the plant throughput and recovery. Production of direct shipping lump ore and sinter fines is forecast at around 1.5 million tonnes in 2011 and, based on current and historical resources, growing to approximately 5 million tonnes in 2015 and thereafter. Production from the first four stages is expected to continue at about this rate through to about 2028.

May 1, 2011

By Matthew Janes

Advantages: Clean samples Low sample disturbance Very low spoil Versatile Fast Penetrates all formations Resonant Drill 100 or 150 kW Self tuning to resonance Rotation to 100 rpm Increased depth in dense soil Increased productivity Reduce water use Reduce casing plugging

May 1, 2013