Search Documents

By R. Bruce Graham

The formation, evolution and classification of peat bogs is discussed. Factors resulting in the internal and external morphological changes in a bog are described. The fibrous, absorptive and sterile properties of peat moss account for its widespread use in horticulture and related fields. These properties also account for its usefulness as a binder in pelletizing, as an insulating material in bat tons and in panel construction. Peat, the humijied product of peat moss is used in market gardening and sod growing. It is utilized in Europe as fuel. It is a source of activated carbon and gas. Potentially peat can be used to produce waxes, resins, tannins, cellulose, hemicellu/ ose, humic acids, lignin and hymatomelanic acid. At present other cheaper sources are available.

Jan 1, 1984

By C. Langer

Although the existence of precious metals, particularly those of the platinum group, in the nickel ores in the Sudbury district has been known for a good many years- almost as long as the ore deposits themselves- the Mond Nickel Company were the first to effect their recovery on a commercial scale. The precious metals values of the different Sudbury ores vary considerably, and are generally higher in the copper-rich ores. These values are so very small that a direct determination in the ores gives quite unreliable results. This is not surprising if one considers that some of the ores contain on1y one unit of total precious metals in about two million units of ore, and that this one unit will consist of seven different metals, each with a different chemical behaviour. It is only after the ores have been smelted to a Bessemer matte containing about 80 per cent combined copper and nickel that the precious metals content can be determined with some degree of certainty. From the figures thus obtained, the precious metals content of the ores can be calculated, provided the tonnage of ore used to produce one ton of matte is known. The recovery of these minute quantities of precious metals out of ?such a large amount of gangue and sulphides of iron, copper, and nickel seems at first glance a commercial and technical impossibility. Nevertheless, science has found a way to conquer all the difficulties, and quite substantial quantities of the precious metals contained in the Sudbury nickel-copper ores have been regu1arly recovered for many years by the Mond Nickel Company.

Jan 1, 1927

By George C. Coupland

"THE PRELIMINARY EVALUATION of the orebodies was computerized for tonnages and grades on a 20- by 20-ft grid. The evaluation was based on drill-core intersections over 40-ft vertical projections coinciding with the proposed bench intervals, taking the deviations of the drill holes into account. The computer print-outs gave an ore distribution and evaluation bench by bench and indicated the areas of varying mineralization. The two orebodies have a combined length of 2,200 ft. and a maximum width of 600 ft. They strike almost due north, dip about 85 degrees east and rake to the north. The computer print-outs were used to design an open pit with an over-all waste to ore ratio of 2.58:1. At the outset, the waste to ore ratio was 4:1. The pit is tear-drop shaped, with the narrow end to the south, and at the surface is 2,600 ft long by 1,800 ft wide. Ramps are 100 ft wide, with a 10% grade. The south ramp is left-handed, starts at the southeast and will continue to the bottom of the pit. A second ramp on the west and north walls runs from surface to join the south ramp at 7 bench. This ramp will handle the total pit production when part of the south ramp, from 4 bench to surface, is lost due to the underground operation. Over-all wall slopes are 53 degrees, and are laid out to avoid prominent protuberances which could relax and become unstable and potentially dangerous (Fig. 1) ."

Jan 1, 1974

By V. F. Hollister

Four conditions are commonly accepted as being needed for the development of native sulphur deposits in sedimentary rocks : (1) ample sulphate-bearing evaporite, normally anhydritic; (2) proximity to petroleum deposits; (3) a hydrodynamic system of communication between these two; (4) a stratigraphic or structural trap to prevent escape of the sulphur and sulphur -bearing reaction products. When any of these requisites are absent, apparently no significant residual bio-epigenetic sulphur deposit will form. These requirements are, however, satisfied in some areas, which include both the Triassic and Devonian evaporites of northeastern British Columbia.

Jan 1, 1977

By Arthur L. de Carle

"IntroductionThe Key Lake uranium-nickel deposits are located within a Mineral Lease centred at latitude 57 ° 12' north and longitude 105 °39' west along the southeastern rim of the Athabasca sedimentary basin in northern Saskatchewan, approximately 240 km north of La Ronge (Fig. 1). Access is provided by an allweather provincial highway from Pinchousc, situated about 200 km to the south, and a private airstrip maintained at the mincsitc.These deposits have been developed by Key Lake Mining Corporation on behalf of the Saskatchewan Uranium Joint Venture. Participants in the joint venture include Saskatchewan Mining Development Corporation (50%), Urancrz Exploration and Mining Limited (33 1/3 %) and Eldor Resources Limited (16 2/3 %).Considerable geological work has been conducted on the Key Lake orebodies and reported in summary papers published by Dahlkamp and Thn, (1977), Dahlkamp, (1978), Gatzweiler eta/., (1979) and Kirchner el a/. , (1980). However, intensive geological research is ongoing, particularly since many problems regarding ore genesis and controls remain unresolved . Exploration History and DevelopmentThe events (Gatzweiler eta/., 1980) which led to the discovery of the Key Lake ore bodies began in the summer of 1971 by following up on the reports of airborne radiometric anomalies and anomalous radon values in the Zimmer Lake water situated approximately 5 km to 6 km to the southwest. This work succeeded in locating a few high-grade uranium and nickel-bearing boulders associated with esker material. An integrated program, consisting of various geochemical and geophysical surveys along with diamond drilling, culminated in the discovery of the Gaertner orebody during July 1975. Subsequent fence drilling across the strike extensions of this ore structure located the Deilmann deposit, approximately I km to the northeast, in June 1976"

Jan 1, 1986

By Michael Chender

Emerging Equity Sources ? Larger IPOs ? China Inc. ? Other sovereign wealth funds ? New funds and higher allocations ? Private equity

May 1, 2010

By C. T. Bischoff

Introduction Air conditioning is a term which has come into common use only during our generation. By definition, it means the positive and accurate control of temperature, humidity, movement, purity, and component constituents of the atmosphere within an enclosure. Claiming such results for Noranda's ventilation system, or for that of any other large mine, at present would be an idle boast. However, we are working toward that end with considerable success. Modern underground ventilation at Noranda dates back about six years. The later development of air conditioning is in its fourth season, but still in the experimental stage. Various ingenious methods have been devised to cool mines which, because of climatic or geological conditions or depth, are excessively warm. A few installations have been made to warm intake air during the winter months where this is necessary. However, the method currently in use at Noranda is unique in that it accomplishes both ends by one process. This method utilizes the freezing and melting of ice to equalize year-round temperatures. Mining Methods While a discussion of mining methods at Noranda is not proposed in this paper, a brief summary may be in order. The Horne mine of Noranda Mines, Limited, has been developed by six shafts, four of which are now active. The most recent, an internal shaft, extends to 6,000 feet below surface, but all of the ore mined to date has come from above the 3,000-foot level. Figure 1 shows a model of principal ore bodies. The area mined is relatively small in plan, considering its vertical extent and the tonnage per vertical foot. Most of the ore lies within an ellipse about 600 by 1,000 feet. While this has certain advantages, the mining of such massive orebodies has presented many problems.

Jan 1, 1947

By L. Lafrenière

A trend in mining exploration is to increase the number of geophysical parameters collected and interpreted for geological features in a given area. Airborne technology now allows us to simultaneously combine electromagnetic, gravity, aeromagnetic and radiometric surveys. We report the results of a multiparameter survey conducted in the area of Kamiskotia, Ontario. This area is located near and on the West side of the multi-metalliferous Kidd Creek deposit. Various metallic occurrences are reported in the studied area. Integrating multiple parameters in the interpretation produces a more detailed pseudogeological map than what has already been published. 3D interpretation has been undertaken using some of these parameters and suggests that future work is required in 3D earth model solutions in order to fully use all parameters.

Aug 1, 2013

By R. Lovat, J. A. Hunter

"The design, development, and verification of the Lovat 7.6metre diameter full-face tunnel-boring machine is reviewed. Programmatic and technical challenges are outlined with a review of the specifications and the design to meet these requirements. Subsystem designs are presented for the waste material removal, ventilation, cutter head, structural support, advance technique, water removal, and interfaces with the Donkin-Morien Mine. The techniques used to verify that the design meets the requirements is by testing in the Lovat factory and in the field. Certification of the machine for use in a methane environment is discussed.IntroductionStudies have concluded that the average annual worldwide tunnel construction is 500 kilometres at an estimated average co st of $3,400 U.S . per linear metre. The total market value of the tunnelling industry is estimated as approximately $1.7 billion U.S. per annum. Of this, the current market for tunnelboring machine excavation is approximately $270 million U.S. per annum worldwide with a further potential of $250 million if more contractors are convinced that Tunnel-Boring Machines (TBM) are more suitable than conventional techniques. The worldwide civil tunnelling market has the potential to double each year in the next 5 to 15 years. Growth has been identified in the energy and mineral resources sectors of the economies of many nations and a significant volume of machine tunnelling studies and trials are presently underway for the extraction of coal, uranium , heavy oil or oil sand fuels, metallic and non-metallic industrial minerals and base metal or rare earth ores. Further tunnel projects for regional transportation, waterpower, irrigation , high density urban transportation, storm water sewers and water supply purposes are continually being implemented with new concepts like military security facilities and underground storage schemes being considered.Lo vat Tunnel Equipment of Rexdale, Ontario, the only Canadian manufacturer of TBMs was incorporated in 1973 to manufacture so ft ground tunnel-boring machines to satisfy this growing market demand. Lovat has produced an average of 5 machines per annum during the period 1972 - 1982 and has established an international reputation for competitive costs, quality of construction, after-sales service, and reliability. As of June 1982 Lovat TBM's have been used to tunnel over 240 km in projects throughout the world."

Jan 1, 1984

By W. Rostoker

Packing Experiments The porosity and most of the other physical properties of a coherent mass of any material built up by the packing together of discrete particles will obviously vary with, and be governed by, the manner of association of the particles. The relation of packing to powder metallurgy has been discussed in some detail by at least two authors. Packing Theory Theories of particle packing have been put forward by C. C. Furnas and A. E. R. Westman. Although their approach to the problem is not the same, their conclusions are similar. In the process of packing, they visualize the voids of a uniformly sized material becoming filled with particles of a smaller size, and the voids between these being filled in turn with still finer particles. Obviously, if this process is carried ad infinitum, the resultant mass will have the same density as the constituent particles. In practice, of course, such a density of packing is never attained. In addition, the premise is made that successive particle sizes must fit into the voids left by the immediately larger particles- an assumption requiring definite size gradations and also particle shapes. It remained, then, for theory to correlate relative diameter ratios, and proportions and numbers of sizes of particles, for requisite packed densities. Briefly, the following principles were postulated: (a) For an infinite diameter ratio between largest and smallest sizes, an infinite number of particle sizes in proper proportion is required to give natural density. (b) For a given diameter ratio, there is a maximum number of permissible particle sizes for maximum packed density (Furnas). (c) Provided the particle shape is spherical, or approximately so, the proportions o particle sizes can be calculated. (d) The ratios of successive diameters of particles are in geometric progression.

Jan 1, 1947

By Yoginder P. Chugh

This paper discusses an ongoing field study in southern Illinois (USA) that focuses on: 1) Identifying mechanisms of instability in the set-up rooms (SR) and their T-junctions with headgate and tailgate entries, 2) Developing alternate 3-entry and 4-entry set-up rooms geometry using 3-D numerical analyses, 3) Implementing developed geometries in cooperation with mining professionals and regulatory agencies, and 4) Demonstrating performance of implemented geometries through field monitoring. Illinois longwall mining operations typically experience ground control problems (roof falls, rib sloughing, floor heave, etc.) within SR layouts and around the T-junctions of SR. These occur around the areas where the SR for adjacent longwall face (to be mined) connect with the SR of the previously mined face, and around the tail-gate entries of the mined-out longwall face and around the T-junctions of SR. The problems manifest as highly fractured immediate roof strata, major shear zones in the roof, horizontal displacements within the excavations that result in shearing off the heads of the bolts, floor heave and severe rib sloughing. Similar observations have also been made in longwall mining in Utah.

Aug 1, 2013

By C. M. Campbell

IN 1934 Newfoundland, after extravagant operation based on exaggerated ideas of what she had to work with, became bankrupt, ceased to be a self-governing Dominion, and passed into the hands of a Commission. Since the days of Dawson, Canadians have been taught that no country in the world is as rich as their own. This idea has become a religion; contrary views are heresy, and are suppressed even by technical organizations and government departments. Following the alleged habit of the ostrich, we have buried our heads in the sand and have refused to face the facts. This policy of "to have today and to hell with tomorrow" is now bearing fruit. After forty years of operation on the basis of unlimited natural wealth, with resulting over-expansion, wholesale depletion of capital assets, and huge borrowings, we are, now that our wealth has been shown to be very limited, face to face with the status of Newfoundland. Already, in this Province, commission government of bankrupt municipalities is not uncommon. The ostrich is referred to as the most foolish bird in the world. That is not the case-no ostrich ever hid his head in the sand. In the clear air of his home on the South African veldt, an area characterized by low bushes, he is a conspicuous object. When danger approaches, he lowers his head; matches his background, the bushes; and danger passes him by. This leaves the Canadian, with his head still in the sand, to fill the r61e cast for the ostrich. Fortunately, a few Canadians never did get their heads covered; others are getting them out far enough to see what is going on. Their comments are very much to the point. "Nowhere in the world," says Mr. Meighen, "has more harm been done to any country by an exaggeration of its resources and potentialities than has been done in Canada'.

Jan 1, 1941

By David Runnels

The Mount Wright iron are mine and upgrading plant were brought on line in the fall of 1975. The mine is located near the Quebec - Labrador border some six hundred miles northeast of Montreal. This paper describes the crushing, grinding and concentrating facilities at Mount Wright, and some design: criteria used in equipment selection and flow sheet design. Also mentioned are some "asbuilt" modifications. A brief description of the over-all flowsheet is also included. Introduction IN SEPTEMBER 1970, the Quebec Cartier Mining Company started development of the Mount Wright iron ore mine. The estimated are reserve is in excess of 1,000,000 ,000 long tons of concentrates, with an average crude are grade of 31.5% Fe. The run-of-mine ore is crushed, ground and concentrated to a product having 66% Fe and 5% silica at an annual concentrate production r ate of 18.4 million long tons. The daily production rate of over 50,000 long tons of concentrate necessitates a daily mine output of approximately 250,000 long tons of material, of which 50% is waste.

Jan 1, 1977

By Roger Lacroix

L?arrivée de nouvelles technologies sur le marché des foreuses portables combinée au besoin des mines à mieux consommer l?énergie électrique ont permis d?identifier le potentiel de deux nouveaux type de foreuses présentement utilisées en Afrique du Sud, à savoir les foreuses électriques et les foreuses hydrauliques actionnées à l?eau. Grâce à la collaboration de mines Niobec et Géant Dormant de Cambior Inc., ainsi que d?Hydro-Québec, le potentiel réel d?économie énergétique des foreuses portables hydrauliques et électriques par rapport aux foreuses conventionnelles à air comprimé a été évalué pour des roches dures et moles. Ainsi, cet article a pour objectif d faire ressortir ces potentiels d?économie énergétiques. En outre, les résultats pour une mine mécanisée et une autre mine de type filonien, dans lesquelles on retrouve des conditions de terrain différentes, seront présentés. Les résultats montrent un potentiel d?économie énergétique d?environ 70% pour la foreuse électrique et d?environ 50% pour la foreuse actionnée à l?eau. Ces résultats montrent qu?il est possible d?obtenir une meilleure efficacité énergétique par mètre foré. Ainsi, il apparaît maintenant intéressant de poursuivre les travaux de développement des deux technologies pour les applications de forage vertical et de tensionnement des boulons, et de viser à accroitre le taux de pénétration de la foreuse électrique pour le rendre équivalent à celui de la foreuse à air comprimé.

May 1, 2007

By Timothy W. Ellis, Abbas H. Mirza, R. David Prengaman

Recycled lead, i.e. material produced by the recycling of lead-acid batteries, has become the primary source of lead in much of the world. This has been important to the recycled lead industry as other uses have dwindled, e.g. lead based pigments, chemicals, fuel additives, solders and CRT glasses. Presently, battery manufacturing accounts for greater than 85% of lead consumption worldwide while recycled lead accounts for approximately the same market share of lead supply. Battery manufacturing and production of recycled lead are intimately coupled. In 2007, of all the industrial base metals, lead from lead-acid batteries had the highest recycling rate in North America at greater than 95%. In this paper we will review some of the processes and technologies used in a modern lead acid battery recycling facility, and how recycled lead has become the material of choice for battery construction through the development of a recovery and refining process that exceeds the industry requirements. We will also briefly review an advanced air emissions treatment system in a modern lead recycling plant that demonstrates the feasibility of a new maximum available control technology (MACT) for secondary lead smelters.

Jan 1, 2011

By A-A. Bogno, M. Rappaz, J. Valloton, H. Henein

"Rapid solidification of Al-Cu droplets of eutectic composition was carried out using Impulse Atomization in an argon atmosphere, to study the microstructures forming at different cooling rates and undercoolings. Two distinct morphologies were observed within the investigated Al-33wt%Cu droplets microstructures: (i) A regular lamellar morphology and (ii) an undulated morphology. The volume fraction of each type of morphology was measured as a function of the droplet size and the nucleation undercooling was deduced using the hypercooling limit equation. The scale of the microstructures was determined through measurements of inter-lamellar spacing across and along the growth direction. Growth velocity and undercooling were deduced using Jackson and Hunt (1966) eutectic growth theory. Finally, mechanical properties were estimated through micro-hardness analysis using a Vickers hardness tester, revealing exceptional properties for an aluminum-copper alloy. Indeed, the hardness values, increasing with growth rate and undercooling, were 3 times higher than the values obtained in hypo-eutectic Al-Cu alloys.INTRODUCTION Eutectic alloys are very attractive due to their good fluidity allowing ready shaping of parts in casting processes as well as in thermal spray deposition. In addition, they yield microstructures with high mechanical properties, by the virtue of their scale/size which is defined by the solidification parameters and the thermodynamic and thermophysical properties of the given alloy. Therefore, it is important to understand the relationship between the microstructures and the solidification parameters of eutectic alloys in order to control their solidification path and mechanical properties. The latter could be improved by either adding an appropriate strengthening component to a base eutectic material (Böyük, MaraslI, Kaya, ÇadIrlI, & Keslioglu, 2009) or by refining the microstructures for more effective dislocation pinning (Campbell & Campbell, 2003). Tailoring the microstructure can also be beneficial to chemical (Freitas, Osório, Spinelli, & Garcia, 2014; Osório, Freire, Caram, & Garcia, 2012) or electrical (Kaya, 2012) properties of the material. Eutectic-type microstructures, usually formed from liquid (eutectic transformation) or solid (eutectoid transformation), are made up of two or more different phases, generally of lamellar or fibrous (rod like) morphologies (Kurz & Fisher, 1998). In general, a binary eutectic structure can be regular (when both phases are non-faceted) or irregular (one of the two phases is faceted), the two solid phases having roughly the composition of the liquid from which they are formed."

Jan 1, 2017

By S. Fahland, P. Vogel

"The Gorleben salt dome has been investigated since 1979 for its suitability as a repository for the disposal of high-level radioactive wastes. The geoscientific surface exploration was followed by underground exploration of the site beginning in 1983: underground excavation work included the sinking of two shafts from 1986 to 1994, the excavation of the infrastructure area and of drifts located in the first exploration area EB1 within the following years. The exploration was interrupted for ten years from 2000 to 2010 as part of a moratorium. After the expiry of the moratorium in March 2010, the geoscientific underground exploration at the Gorleben site was resumed. The investigations were interrupted again in autumn 2012 due to a political decision. The exploration programme included extensive geoscientific investigations: geological exploration, geophysical investigations, mining exploration and mining observation, laboratory tests, in-situ geotechnical measurements, geological modelling and numerical model calculations. To analyse and interpret the results of the in-situ measurements and mining observation geomechanical, thermal and thermo-mechanical model calculations were carried out. One of the main elements of the in-situ geotechnical investigations were high-resolution geothermal measurements performed in boreholes used for geological exploration and geotechnical tests.The geothermal measurements are used to evaluate several geotechnical findings, e. g. drift closure, rock deformation, stress change, and are completed by thermal model calculations to analyse and interpret the results of in-situ measurements and mining observation. The model calculations have been carried out using the special purpose JIFE code. To consider the whole exploration mine with the adjoining host rock as well as the successive excavation of drifts and boreholes in detail a three-dimensional finite-element model was developed. The model calculations are used to analyse the cooling-off of the surrounding rock of the drifts caused by ventilation. The cooling-off of the surrounding rock is an ongoing process affecting the results of further geotechnical measurements in the near field of the drifts. To predict a realistic time and space dependent distribution of the temperature field of the host rock within the exploration area which is influenced by ventilation thermal model calculations are necessary. Comparing the calculated temperature field with the in-situ determined rock mass temperature field within the exploration area EB 1 the results show a sufficient agreement. Furthermore there is very good correspondence, both qualitatively and quantitatively, between the experimental and the calculated findings regarding the temperature profiles including the effects of excavation and ventilation of the drifts."

Jan 1, 2015

By J. P. Rajot, H. Mouzannar, M. Bost

"The design of rock foundations may need to evaluate shear strength of rock-concrete interface by performing laboratory direct shear tests. A series of tests were carried out on specimens for different values of the spacing free of encapsulating material about the shear plane and different values of normal stress. Different kinds of failure were observed and not necessarily at the rock-concrete interface. The spacing free of encapsulating material appeared to be of significant influence on the test results. A mechanical analysis is presented which illustrate the influence of the loading conditions in the direct shear box on the failure mechanism. INTRODUCTIONThe design of rock foundations subjected to significant lateral loads requires defining the value of the shear strength of the interface between rock and cast in place concrete. Verifying the stability against sliding of strip footings subjected to inclined loads (SETRA, 2009) or concrete gravity dams (CFBR, 2013) are common examples where design modelling approaches imply the shear strength, sometimes the deformation behavior, of the rock-concrete interface, more or less assumed as a failure plane.Defining the behavior of rock-concrete interfaces relates to tribology. Many studies have been conducted to improve the representation of this behavior (e.g., Johnston & Lam, 1989; Kodikara & Johnston, 1994; Gu, Seidel & Haberfield, 2003; Saiang, Malmgren & Nordlund , 2005; Fishman, 2008; Eltervaag, 2013; Gutierrez, 2013), raising many questions. The behavior appeared to be influenced by many factors such as the geometry of the interface which is not planar, the roughness of the natural rock, the rock mineralogy and the concrete formulation. In addition, the study of the shear strength of rock-concrete interfaces involves considering the two different deformation behaviors of both rock and concrete. Finally, the observed failure mechanism is strongly influenced by the initial cohesion due to adhesion between the two materials when concrete is directly cast onto rock."

Jan 1, 2015

By F. Liu, S. Rezaei, M. Muinonen, M. Barati, V. L. Lakshmanan, S. Marcuson

Canadian nickel-copper ore deposits have been a major source of nickel, copper, cobalt and precious metals for more than 100 years. The two main minerals of interest, pentlandite (Pn, (Ni,Fe)9S8) and chalcopyrite (Cp, CuFeS2), are usually accompanied by large quantities of pyrrhotite (Po, Fe1-xS). Until the 1950s, Po containing small amounts of nickel was routinely smelted as part of the valuable Ni concentrate. The rapid growth in Ni demand following the Second World War created impetus to treat the Po separately. This action would liberate a valuable smelting capacity for higher value Pn, allow for recovery of Ni locked in Po, convert the Fe to iron oxide or metallic iron pellets, and recover S as sulphuric acid or elemental sulphur. The roasting process also has the potential to produce energy due to the highly exothermic oxidation of Po. The Ni industry would then have a “waste-free” process. Both Inco (now Vale) and Falconbridge (now Glencore) developed processes and built large industrial plants for this purpose that operated with some success. But technical issues and tenuous economics were continual challenges. By the early 1980s these industrial operations were closed. Sophisticated froth flotation methods of rejecting Po were developed, and Po containing up to 1% Ni became a waste material reporting to the tailings stream. As part of a major study on possible processing methods of Po for both value recovery and waste remediation, this paper presents a historical perspective on Canadian Po tailings with regards to their generation, inventory, value, and attempts to process them.

Jan 1, 2017

By L. Heber Cole

In making this plea for a better and more sympathetic understanding of the non-metallic industry, I do not for one minute wish to give the impression that I in any way belittle the wonderful strides that have been made in the exploitation of our metallics. We in Canada can be justly proud of our Sudburys, Norandas, Flin Fions, and of the remarkable growth of the Consolidated in British Columbia, and at the same time, without in the !east detracting from these worthy undertakings, be equally as proud of our asbestos, gypsum, salt, and coal deposits, as well as of our building-stone and limestone industries. If, in my remarks, I have occasion to compare the metallic with the non-metallic industry, I do so, not with any idea of dimming the glory which the metallics of Canada have gained- not only in our own country, but in the world at large-but for the purpose? of bringing to your attention the fact, perhaps not very well recognized, that Canada contains deposits of non-metallics well worth y of your serious consideration. In the past 33 years, namely, since 1895, the value of non-metallics produced in Canada has exceeded the value of metallics in 19 of the years, and for the last three years has been increasing rapidly. The war years (1915-1918 inclusive) naturally saw an intensive metallic production, but since that time, with the exception of 1925, when there was a general depression throughout the whole country, the non-metallics have been in the ascendency.

Jan 1, 1929