Search Documents

By A. A. Brant

"Improving geological and geophysical evaluation should serve to reduce the early-stage risk assessment and there-by contribute to exploration expenditure stimulation. The limitations of present-day methods are reviewed, particularly as to anomaly causes, depth penetration and quantitative physical interpretative abilities. Some of the problems now under study are discussed. Future developments expected include the treatment of quantitized geologic and geophysical data, as well as continuing attempts toward computerized interpretation."

Jan 1, 1967

By J. H. Archibald

"In mines employing cut-and-fill stoping (sand fill), ore passes are built as mining progresses upward. These ore pass raises are generally made from timber and form a vertical ""chimney"", like a very tall log cabin. Traditionally the chimney, or raise, is square in shape and is constructed from square timbers with stepped ends as shown in Figure I. The timbered raise is thus surrounded by sandfill on its outside, leaving the centre open for passing ore down through it. Each layer consists of four timbers and rests flush on the layer below. The corners are frequently pinned or spiked.Under certain conditions in sandfilled stopes large horizontal loads may be transmined to the raise cribbing timbers, or the ""chimney's"" walls. In deep mines, where rock bursts are a problem, it can be shown that one of the conditions for rockbursts to occur is that the burst zone be stiffer and weaker than the surrounding rock(l). This allows a strain energy build-Up in the rock surrounding the burst zone, and the rate of release of this strain energy is known to be related directly to the over-all strength and stiffness of the rock in the burst zone. In stopes that are sandfilled, attempts are, therefore, usually made to increase the strength of the sandfill by the addition of large-sized waste rock and Portland cement. These measures usually achieve the desired strength of the sandfill and, consequently, the severity and frequency of rockbursts can be reduced.Problems may arise when the now chunky sandfill transmits high loads to the raise cribbing along with relatively large move- merits. This leads to heavily stressed and strained cribbing timbers the Coeur d'Alene district in Idaho, raise cribbing failures are common. A typical mode of cribbing failure is shown in Figure 2. One learns in statics that a structure shaped like the crib in Figure I is inherently unstable , at least from a structural standpoint. The crib has pivoted, in Figure 2, into a rhombi c shape and supports very little load. Soon the four-foot square raise cribbing made from 5 in. by 5 in. timbers will no longer pass ore."

Jan 1, 1991

By J. G. Schofield, C. G. Tan, R. J. Ord

"Most electric furnaces in the nickel and copper smelting industries are still fitted with conventional electrode holders which consist of water-cooled electrical contact clamps and a pressure ring. The water cooling exerts a significant cooling effect on the electrode column. The importance of controlling the temperature of the Soderberg electrode paste at the contact clamp area is examined, using in-plant experience and computer simulation of the paste melting and baking process. In addition to the effect of water-cooling, the effect of other variables, including the mantle air temperature, the electrode current, the furnace freeboard temperature and the electrode slipping rate are discussed. Ways in which the variable heating conditions in the paste melting zone can be controlled are outlined.IntroductionIn most non-ferrous electric smelting operations, the breakage of Soderberg electrodes is an infrequent, isolated occurrence. Occasionally, however, a rash of breakages may be experienced on a particular furnace for what appears to be no obvious reasons. The extent of the breaks may not exhibit a uniform pattern; sometimes the break may be less than half a metre above the electrode tip; at other times it may be at or just below the roof level. The latter type of break is, of course, the most dangerous since it is closest to the non-baked, weak portion of the electrode paste column. No matter where the breaks occur, they result in abnormal furnace power, charging and tapping conditions and loss of production while the new electrode section is slipped and baked. On a six-electrode furnace, breakage on one electrode has the immediate effect of reducing the total furnace power by one-third. On a three-electrode furnace, the effect is more drastic, one half of the power being lost."

Jan 1, 1995

By A. M. Esteves

This paper offers an overview of local content policies and practice in the mining sector. Specifically, the paper aims to answer the question of how national and regional governments, industry and civil society can work together to seek an optimal outcome while pursuing their diverse objectives. The paper begins by defining local content and its scope at the subnational level. Specific recommendations for the design of local content policies to mitigate social, economic and governance risks are developed. The document then offers some recommendations regarding the role of partners in design, implementation, monitoring, and enforcement of local content policies.

Aug 1, 2013

By R. W. Boyle

"The concept of using chemical methods in prospecting dates back at least to the middle of the 16th century. Modern methods of geochemical prospecting, however, based on secondary haloes and utilizing trace-element techniques, were first practised in the U.S.S.R. and the Scandinavian countries in the 1930's. After 1945, methods based on soils, stream sediments and vegetation were rapidly developed in the U.S.A., the United Kingdom, Canada, France and other countries.The modern methods of geochemical prospecting owe their rapid development in the 20th century to the following:1.-Recognition of the primary and secondary dispersion haloes and trains that are associated with all mineral deposits. 2.-Development of accurate and rapid analytical methods utilizing the spectrograph and the various specific sensitive colorimetrie reagents, especially dithizone. 3.-Development of polyethylene laboratory ware of all types and the development of resins. This permitted greater freedom of field analyses and reduced the incidence of contamination.4.-Development of gas chromatography. This permitted the rapid and accurate determination of hydrocarbons in petroleum prospecting.Future research in geochemical prospecting should be focused on the following tasks: 1.-Definition of geochemical provinces and their relation to mineral deposits. 2.-Development of methods for discovering large low-grade deposits. 3.-Development of methods for discovering deeply buried deposits. 4.-Further development of methods to outline primary haloes. 5.-Eiucidation and formulation of techniques to relate the size and intensity of anomalies to the grade of the deposits. 6.-Development and refinement of biogeochemical methods, especially those based on indicator plants, chlorotic or toxic effects, and microbiological techniques. 7.-Definition of the types of primary and secondary haloes associated with accumulations of oil and gas."

Jan 1, 1967

By C. Jewell, G. H. Rupay

"67 - 2:15-3:00Regeneration of Hydrochloric Acid from Waste Pickle Liquor Using a Fluidized Bed Reactor System. G. H. RUPAY and C. JEWELL, Dominion Foundries and Steel Ltd., Hamilton, Ont.The disposal of acidic waste liquors from pickling processes has always been a problem for the steel industry. With increased awareness toward environmental control and the problems acidic wastes create, processes utilizing recovery and regeneration of the waste acids are becoming more popular. This paper describes the Keramchemie/Lurgi process for regenerating hydrochloric acid from waste pickle liquor using a fluidized bed reactor system. The process parameters are outlined, together with a brief description of the equipment. This is followed by a discussion of the operating problems and concludes with economic data."

Jan 1, 2000

By M. S. Badollet

"DURING the past five years, production of asbestos fibers has increased in all countries that list asbestos as one of their mineral resources. Despite the many small mines that have been opened in Canada, United States, Mexico, South America, Italy, South Africa, Australia, Yugoslavia, and Rhodesia, the supply still does not meet the demand. It is estimated that total 1952 world production of asbestos fibers of all varieties approximated 1,600,000 tons, with Canada supplying 966,382 tons (I), or 60 per cent of all fiber mined.Asbestos fiber brokers continually are offering odd-lot samples of chrysotile, amosite, crocidolite, tremolite, and anthophyllite fibers to manufacturers, •quoting fantastic prices for tonnages •varying from just a few to 50 or more in a month. In many cases, the samples are not properly graded and contain quantities of rock impurities and finely ground dust.When vendors submit samples of asbestos fibers, the manufacturer should consider• them in terms of price, quality, quantity, and as possible substitutes for fibers currently used in his products.Grading of these odd-lot fibers in most cases has been poorly done, with resultant non-uniform fiber lengths. In some instances, a number of miscellaneous lots of fibers have been .blended for sale. This blending produces a fiber that is difficult for the manufacturer to accept as a substitute for the well-standardized Canadian fibers."

Jan 1, 1953

By J. S. Edwards

The ISASMELT? process is recognized worldwide as a modem, flexible, environmentally-friendly and low capital cost smelting technology. Due to the inherent simplicity, and the advanced process control that has been developed, personnel become competent within weeks of being introduced to the ISASMELT? technology. This compares with the years required to become proficient with alternative technologies. Copper smelters in Australia, USA, India, China, Peru and Zambia have installed ISASMELT? technology under licence from Xstrata Technology. In the secondary copper business, plants in Belgium and Germany are processing copper and/or lead materials in ISASMELT? furnaces in a two stage process. In a single furnace smelting is followed by converting. Both plants have exceeded design capacities and are continuously improving their performance. The next evolutionary step for the technology is the implementation of the continuous copper converting process on a commercial scale. The present work describes the design status of the continuous converting process - ISACONVERT?.

Jan 1, 2007

By Jerry M. Whiting, Neil J. Duncan

"Does Canada need a mining industry? Isn't it a chronically depressed collection of businesses that pollute the air and water and tear up the countryside? Wouldn't it be better if Canada's investors devoted their attention to high-technology endeavours, tourism, and other relatively pleasant tasks?Probably the answer to whether Canada needs a mining industry in the 21st century is to look at the real mining industry that is in operation today. The facts indicate that mining is a very important contributor to Canada. It has certainly encountered some challenging times during periods of recession, and it face s severe and continuing problems of cost and competition in world markets. However, uneconomic mines have been closed, others suspended, and productivity has risen dramatically with employment at 77 000, down from 101 000 in 1981. The country's metal and non-metal mines, metallurgical plants and semi-fabricated metals industries employed an estimated 378000 workers in 1986, and paid wages than any other sector of the Canadian economy. This effort resulted in the production of 60 different metals, non-metals and structural minerals valued at $13.5 billion.The trade aspects of the mining industry are of paramount importance. If there is a reason for this situation to change during the next century. it eludes the authors. Canada has the well-developed expertise to discover, evaluate, develop, operate and profit from existing and new businesses based in an enormous area endowed with a nearly unbelievable variety of mineral resources. Many countries throughout the world must rely on producers like Canada, if they are to maintain and/or improve their standard of living."

Jan 1, 1988

By I. A. Tinto

"Labrador City is located in the southwestern portion of Newfoundland-Labrador, approximately 965 kilometers north-east of Montreal. The mine and beneficiation complex of the Iron Ore Company of Canada, known as the Carol Project, is situated 535 metres above sea level in a climatic region characterized by cold winters and short, cool summers.HistoryThe Iron Ore Company of Canada commenced work in the area in 19 4 9' however, it was not until 1958 that the decision was made to proceed with mining operations. The ore body consists of Specular Hematite (Fe203) and Magnetite (Fe304) with small quantities of Limonite and Geothite. The average grade of the ore bodies is 39% iron.The mining facilities, crushing plant, and concentrator were in operation by the early part of 1962. In the summer of 1961, a decision was made to build a pelletizing plant adjacent to the concentrator. This plant was designed, erected and placed in operation during 1962 and the first half of 1963. Since the completion of the pelletizing plant, additional expansions to both the pellet plant and concentrator have taken place in 1967 and 1973. Today, the Carol Project has the capacity to produce 20 million tonnes of concentrate from which 10.5 million tonnes of pellets can be produced.The period 1980-85 spans a period of energy crisis, world-wide recession, and a consequent re-structuring of the North American steel industry as it struggles to survive in an arena of excess world steel making capacity, government subsidized industries, and the increasing competition from overseas and from developing countries.The media headlines over the past few years echo the woes of the industry and the strategy plans for survival of the fittest. Today's buzz words are foreign competition, steel import quotas, joint ventures, employee participation, work rules, quality, productivity, and state of the art technology."

Jan 1, 1986

By W. Petruk

A study was undertaken to determine whether interrelations between mineral grains affect ore breakage during grinding, and to establish a correlation between ore breakage and mineral liberation. A base metal ore from the Brunswick No. 12 deposit in New Brunswick was ground for different periods of time in a laboratory ball mill, and both the unbroken ore and the ground products were analysed by image analysis. The results show that the mode of breakage is strongly influenced by the behaviour of pyrite. Similar size distributions were obtained for material from the 15 minute grind in a laboratory ball mill, for the grinding circuit discharge from a commercial mill, and for pyrite grains in the unbroken ore. This similarity indicates that a 15 minute grind breaks poorly bonded pyrite grains along grain boundaries, and represents the limit of easy breakage for the ore. Such a grind liberates both large separate grains of ore minerals and poorly bonded mineral grains that occur in interstices among pyrite. On the other hand the 15 minute grind does not separate moderately bonded mineral grains nor release moderately bonded interstitial minerals from pyrite; a 45 minute grind in a laboratory ball mill is required. It is assumed that, for Brunswick No. 12 ore, a 45 minute grind in a laboratory ball mill is equivalent to regrinding in a commercial mill. Grinding beyond 45 minutes in a laboratory ball mill breaks the ore by fracturing pyrite across grain boundaries and by chipping grain edges. Such intense grinding does not markedly increase sphalerite liberation from Brunswick No. 12 ore, because most of the sphalerite that can be released was liberated at the 45 minute grind. In contrast the intense grinding increases galena liberation because a significant proportion of the galena occurs as minute inclusions in pyrite. These findings show that ore breakage and coincident liberation depend upon size distributions, intergrowths, and mode of occurrence of the minerals in an ore.

Jan 1, 1988

By F. Doxey

Introduction Numerous papers have been written dealing with the construction and functions of, and the environmental conditions created by, Diesel locomotives. Therefore, it is not my intention to attempt to deal with these phases of Diesel transportation other than to make reference to them in ?relation to and in connection with actual operation. The rapid expansion of industry during recent years and the necessity of products being made available at competitive prices in home and world markets has made the demand for cheaper coal a very serious factor for the coal industry. This condition has meant each coal producing country looking into ways and means whereby greater productivity and reduction in cost could he achieved. Surveys made show that, in addition to face mechanization, savings, in some cases substantial, can be made in transportation. Ventilation The most efficient mines are in-variably the well ventilated ones, for it is true that, where there is good ventilation, there are usually good roads. These combined factors are very essential where Diesel locomotives are used. Good roadways and track allow speed, and good ventilation dilutes rapidly any disagreeable exhaust gases. Locomotive Development In the older types of auxiliary rope haulage, coal hauled per haul-age hand is usually very low.

Jan 1, 1951

By Ahmad Ghahremaninezhad, Rebecca Radzinski

Arsenic is a highly toxic compound that is naturally found in the environment and is released through the processing of sulphide minerals. Arsenate (As5+) is less toxic than arsenite (As3+) and is soluble in water but can form insoluble precipitates when metal ions are present. The arsenic removal processes used in industry assume that arsenic is in its pentavalent state. Hydrogen peroxide can be employed to oxidize arsenite; however, it is expensive. It has been shown that activated carbon can be used to catalyze the oxidation of arsenite with oxygen as the only consumed reagent at ambient conditions with an efficiency of 99% in less than 24 hours. The mechanism which oxidizes arsenite is not yet understood; however, this study shows that a strong oxidizing agent is formed in-situ. The species and amount of oxidant formed were determined via iodimetric titration and electrochemical methods. The production of oxidant was optimized by comparing the amount of oxidant formed in-situ to the relative amount of arsenite oxidized.

Jan 1, 2015

By J. E. Nesset, E. R. Bobicki, K. L. Bilaniuk

The introduction of froth flotation technology in Canada, and in particular, in British Columbia, began not long after it was successfully applied in the Broken Hill mining area of Australia which began around 1905. It proved to be a revolutionary and transformative technology that resulted in marginal operations in copper, lead and zinc becoming profitable in spectacular fashion. The paper presents the technology of both oil flotation and froth flotation in the context of the challenges of the time and its early application in British Columbia at the Le Roi No.2 mine (1903), the Britannia Copper mine (1912), and at the Allenby concentrator of the Copper Mountain mine (1918-19). New-found archival documents indicate the Britannia application to be the first production application of froth flotation for copper ore outside Australia, a claim that is currently made by the Braden mine (now El Teniente) in Chile. Flotation was initially an add-on process following gravity methods but was rapidly shown to be far superior method for the bulk and selective recovery of metal sulphides. Flotation proved particularly successful for the recovery of zinc sulphide (the so-called ‘zinc problem’) which was considered a contaminant at the time. The ‘copper problem’ related to the poor recovery of fine copper sulphide particles that were not amenable to gravity methods. The success of flotation led to changes in both the scale and methods of mining, concentration and smelting in a manner that allowed integrated mining companies to flourish. Many are still with us today. INTRODUCTION The advent of froth flotation in the early 20th century was truly a revolutionary technological development, not only for the mining and metallurgical industries, but arguably more so for business and society overall. The Canadian technology historian Jeremy Mouat stated (1996) “The development of flotation was the greatest single metallurgical improvement of the modern era...it is not overstating the case to claim that flotation was of central importance to the smooth functioning of the global economy”. It should, therefore, be a story of interest to us all. The aim of this paper is not to retell the full story, that has been well covered by others (Hoover, 1912; Rickard, 1916a; Hines & Vincent, 1961; Lynch et al., 2010) but rather to add some Canadian perspective and the key role played by companies and individuals in those early days, focusing on events in British Columbia’s copper industry. EARLY DEVELOPMENTS During the later half of the 19th century, a number of flotation-related patents were issued. These include the 1860 patent (Britain) granted to William Haynes for a process to separate sulphides from ground ore by mixing it with oil (1-10% wt) followed by a separation process in a water-filled vessel; the 1877 patent granted to Georg and Adolph Bessel (Germany) for a process involving the mixing of oil and graphite ore followed by boiling in water to produce a high grade graphite froth (>90% carbon); and the 1885 patent granted to Rebecca ‘Carrie’ Everson for the separation of sulphides by mixing sulphide ore with small quantities of oil, and adding water followed by sulphuric acid. These processes are more properly referred to as bulk oil flotation due to the relatively large quantity of hydrocarbon used.

Jan 1, 2019

By T. M. Waterland

A GREAT deal of work has been done at Britannia during the past three years in improving and standardizing rounds for development headings, and the results obtained have been very gratifying. The round which has recently been adopted as a standard for all drifts and cross-cuts has, in some instances, doubled the average length of break formerly obtained. It has also increased the footage of advance per labour shift and reduced explosives' consumption. At the present time, with a shortage of skilled labour, more control is necessar7 in directing the drilling of rounds. The use of a standard round has been o great assistance to the foremen and shiftbosses. NATURE OF GROUND Most of the ground encountered consists of a moderately silicified chlorite schist, known locally as G.M.S (green-mottled schist). It cannot be termed hard ground, because a three and one-half inch Leyner will drill at an average rate of twelve inches per minute. Due to the abrasive nature of the ground, the gauge of the steel wears rapidly and in most cases one set of steel is needed for each hole. The ground is not 'free breaking and holes must be spaced correctly to obtain a maximum break. DEVELOPMENT OF STANDARD ROUND FOR THREE-SHIFT OPERATION Late in 1940, a development programme was started involving 7,000 feet of drifting, 6 ft. By 7 1/2 ft. In cross-section, in two headings. Plans were drawn up to advance the headings on three shifts. Equipment used in the headings was as follows: D.A.35 Leyner?machines, Eimco Model 12B mucking machines, nine one-ton end-dump cars, one Mancha Little Trammer on the longest heading, 20-pound rail, 4-in. 15 compressed-air line, 15-in. Fan pipe connected to 5 h. P. Coppus fan. Diamond-drill cross-cuts, 16 feet in length, were cut every 250 feet. Switches were installed at these cross-cuts and they served as passing points for the cars. One siding seventy feet in length was cut in each heading at approximately the half-way point. The cycle of operations planned was to muck out, drill, and blast each shift. Previous performance in this type of ground indicated that a daily advance of 12 feet to 14 feet might be made. However, if a better type of round could be developed, an increased daily advance would be possible. A study of the time available for each operation in a net working shift of six and one-half hours indicated that the maximum depth of round that could be mucked, drilled, and blasted each shift would be six and one-half feet. When this maximum depth was decided upon, the next problem was to develop a satisfactory round. Due to ventilation difficulties and to the short net working shift, the whole round had to be blasted at one time. In other words, no blasting of the cut-holes could be done.

Jan 1, 1942

By K. H. Singh, J. N. Szuck, J. A. Riddell

"Hydraulic rock drilling equipment has been in use at Falconbridge over the past two years in both production and development situations. This paper deals with the experience gained in the application of hydraulic drilling in the company's mines and discusses the benefits and problems encountered during their use. The paper primarily focuses on technical, operating, maintenance and economic aspects of the machines, and does not attempt to compare the performances of different machines from the various manufacturers.IntroductionThe Sudbury Operations of Falconbridge Nickel Mines Limited are comprised of five operating mines and two mines under development. All the production comes from underground mines, mostly at depths below 1000 metres. The company, faced with increases in operating costs and difficult mining conditions, has continued to seek solutions with the help of new mining technology.The development of electric-hydraulic drilling machines in Europe had been pursued with great interest and, in 1979, a decision was made to test these machines to prove their technical and economic viability under operating conditions. Since then, a number of electric-hydraulic machines have been evaluated in different situations and currently nine hydraulic machines are being used in the company's various mines. These machines are comprised of two-boom drilling jumbos for development, one-boom machines for longhole drilling and a large-hole-diameter drilling rig for blasthole drilling. One hydraulic jumbo has also been used in a cut-and-fill stope."

Jan 1, 1982

By A. Aftabi

Abstract-To evaluate geochemical aspects of sheared zones, 35 samples of granitoid rocks from an area of shearing >5 km2 at Derehamzeh, Iran were studied geochemically. Relatively unaltered samples within the shear-zone area average 38 ppm Cu, 1.45 ppm Mo, 4.6 ppb Au, 0.21 ppm Ag, <1 ppm Re, 46 ppm Zn, 28.5 ppm Pb, and 0.34% S. Bleached, hydrothermally-altered samples are anomalous in Cu (>896 ppm), Au(>59.5 ppb), Ag(>24.4 ppm), Re(>1.28 ppm), Zn (>164 ppm), Pb (>218 ppm), and S(>0.9%). Some samples from bleached sheared zones that are highly anomalous in Cu (5000 ppm), Mo(23 ppm), Ag(74 ppm), and Au(200 ppb) are characterized by a typical sericitic alteration assemblage consisting of sericite, pyrite, chalcopyrite, and granular quartz. The main anomalous zone extends over about 0.4 km2 in the southern part of the area. The strong Cu- Mo-Au-Ag association in the sericitic shear zones suggests a possible relationship to porphyry copper mineralization, similar to that found in northern Chile. Further studies on drill-core samples in the southern sericitized shear zones are required to determine if more extensive porphyry-type sulfide mineralization is present.

Jan 1, 1997

By A. Aftabi

To evaluate geochemical aspects of sheared zones, 35 samples of granitoid rocks from an area of shearing >5 km2at Derehamzeh, Iran were studied geochemically. Relatively unaltered samples within the shear-zone area average 38 ppm Cu, 1.45 ppm Mo, 4.6 ppb Au, 0.21 ppm Ag, <1ppm Re, 46 ppm Zn, 28.5 ppm Pb, and 0.34% S. Bleached, hydrothermally-altered samples areanomalous in Cu (>896 ppm), Au(>59.5 ppb), Ag(>24.4 ppm), Re(>1.28 ppm), Zn (>164 ppm), Pb(>218 ppm), and S(>0.9%). Some samples from bleached sheared zones that are highly anomalous in Cu (5000 ppm), Mo(23 ppm), Ag(74 ppm), and Au(200 ppb) are characterized by a typical sericitic alteration assemblage consisting of sericite, pyrite, chalcopyrite, and granular quartz. The main anomalous zone extends over about 0.4 km2in the southern part of the area. The strong Cu-Mo-Au-Ag association in the sericitic shear zones suggests a possible relationship to porphyry cop-per mineralization, similar to that found in northern Chile. Further studies on drill-core samples in the southern sericitized shear zones are required to determine if more extensive porphyry-type sul?de mineralization is present.

Jan 1, 1997

By A. R. Sorta, D. C. Sego

ABSTRACT The settling, shear strength, and index properties of oil sands fines-sand mixture tailings (FSMT) for a wide range of solids and fines content are investigated. Results indicate that the liquid limit of FSMT obeys a linear mixture law. The fines-water ratio (FWR) governs the permeability of composite tailings (CT) and CT with comparable geotechnical behaviour can be produced from the same initial FWR mixtures. A phosphogypsum (PG) dosage > 900 mg/kg does not improve the dewatering behaviour of CT. The undrained shear strength of FSMT at the liquid limit is approximately 2.4 kPa, but is dependent on fines content at the plastic limit.

Jan 1, 2013

By P. A. Crane, N. Shirley, Aung Moe, H. M. Nicholson, D. Kan

Kazakhstan’s first commercial copper-leach solvent extraction-electrowinning plant, Central Asia Metals’ Kounrad project, was commissioned in April 2012. Exploiting low grade waste stockpiles produced during Soviet era open pit mining, a 10,000 tpa copper cathode plant was designed, constructed and commissioned within 18 months. Overcoming initial challenges with a workforce unfamiliar with the technology and with extensive periods of sub-zero conditions during winter the project has consistently met targets and produced high quality copper cathodes at cash costs of less than US$1/lb. Challenges encountered during the first two years of operation are described and future plans briefly discussed.

Jan 1, 2014