Search Documents

By Z. Ren, M. Tomlinson, E. Asselin

"Organic carbon blinding is a common, yet often partial, solution to the reduction of preg-robbing. A quantitative method to assess the extent of adsorption of a given blinding agent is presented herein. The adsorption of several blinding reagents on various carbon samples is quantified using electrochemical impedance spectroscopy (EIS). EIS results showed that kerosene is more strongly adsorbed on carbon than sodium lauryl sulphate (SLS), while SLS can hinder the charge transfer process of the oxygen reduction reaction on the carbon surface more effectively. The effectiveness of SLS is pronounced when its concentration is higher than 100 ppm. Raman spectra are presented for selected carbon samples: as the area ratio of the disordered peak to the graphitic peak increases, blinding agent adsorption increases.INTRODUCTION The presence of naturally occurring constituents in gold ores may adversely affect the extraction of gold in cyanide leaching since the gold cyanide complex, Au(CN)2–, can be adsorbed by these constituents (M. Adams & Fleming, 1989; Afenya, 1991; Miller, Wan, & Díaz, 2005). Such ores are known as “preg-robbing”. Preg-robbing behavior may arise from natural carbonaceous materials in the ore (M. Adams & Burger, 1998). In the past decades, a number of pre-treating methods have been developed for refractory carbonaceous ores (Arriagada & Osseo-Asare, 1984; Beer, 1994; Dunne et al., 2007; Jiang, Liu, Xiao, & Yang, 2012; Kohr, 1997; Kulpa & Brierley, 1993; Menne, 1992; Menne & Revy, 1994; Moyes & Houllis, 2010; Petrie, Craw, & Ryan, 2005; Simmons, 1996). The method known as blinding is one of the most effective and economical pre-treatment methods (M. D. Adams & Burger, 1998; Albert, 1923; Darrow, 1924; McQuiston & Shoemaker, 1975; Van den Berg, 2000). Blinding, also referred to as blanking or passivation, uses a chemical reagent to passivate the preg-robbing carbon by selective absorption or wetting (Bas, Altinkaya, Yazici, & Deveci, 2012; Brierley & Kulpa Jr, 1993; Dunne et al., 2012; Van den Berg, 2000; Yang, Qian, Song, & Dong, 2013; Yen, Amankwah, & Choi, 2008; Zhou, Jiang, & Choi, 2014). Organic reagents, which selectively adsorb on the surfaces of activated carbon and “smother” the surface, have been used for blinding carbonaceous matter in gold ores prior to cyanidation. Two comprehensive studies by Abotsi and Osseo-Asare and Adams and Burger have been published on this topic (Abotsi & Osseo-Asare, 1986; M. D. Adams & Burger, 1998)."

Jan 1, 2017

By S. Parkash, A. J. Szladow

Vigorous agitation of suspensions of coking coals in water (or light mineral oils) will often result in catast rophic loss of caking properties. It is shown that this deterioration is not a consequence of oxidation of the coals (by dissolved oxygen), but that it can be qualitatively connected with internal "solid-state" reactions which appear to derive their activation energies from cavitation of the liquid.

Jan 1, 1971

By M. F. Ameur, M. Habak, H. Aouici, M. Kenane

Present study interest by aluminium alloy (Al 7175-T5173) drilled without cooling fluid. The influence of the machining parameters (spindle speed and feed rate) on the holes quality was analyzed. Drilling tools are made of carbide (WC); high speed steel (HSS) and TiN coated carbide (WC-Ti).The Experiment design was reinforced by the application of statistical analysis of variance (ANOVA).The results show that the thrust force is influenced principally by the spindle speed and feed rate. Though, both feed rate and tool materials have statistical significance on the surface roughness. In addition, the objective of correlations between spindle speed and feed rate with the evolution of the machining parameters was established. These correlations were obtained by quadratic regression using the response surface methodology. Finally, useful to select optimum values of drilling parameters, that would minimize thrust force, torque, cutting temperature and surface roughness.

Jan 1, 2015

By Aaro E. Aho

Yukon, one of the most potentially accessible, relatively undeveloped, regions of Canada, has major mineral possibilities. The Klondike placer gold fields and the Mayo silver-lead ?district are the sole major producers but large base-metal re-serves have been discovered in re-cent years and important asbestos deposits are now being explored. Several major exploration companies are active in this region despite short seasons, permafrost overburden, remoteness, lack of transportation, and resultant high costs. Pro-posed new roads can be expected to accelerate development. At ?present the major future mineral possibilities are considered to be lead-zinc, copper, aslbestos, silver-lead, gold, and mineral fuels. These and other mineral possibilities are outlined for various geological subdivisions of Yukon. Major favourable metallogenic features of Yukon include complexity of rock types and structures, widening of the Cordillera with cross-trends, and variety and quantity of mineralization found even with limited prospecting. Comparisons with southern 'British Columbia and the U.S. Cordillera suggest that further exploration will result in discovery and development of more major ore deposits and reserves which will eventually revolutionize economy of mining in Yukon. Such mineral resources, with interior petroleum and natural gas possibilities, and ?huge coastal hydroelectric power potential, are the foundations of a much larger future mining industry in Yukon.

Jan 1, 1958

By J. E. Armstrong

"IntroductionT'HE PRODUCTION of gravel and sand may be considered to be the major mining operation in the Lower Fraser Valley of British Columbia. At least thirty pits are in operation with a yearly production probably in excess of two million yards and a value in excess of one million five hundred thousand dollars before crushing, washing, and sizing. The value of the finished products would probably be double the above figure.Since 1949, the writer and his co-workers have been engaged in the geological investigation of the Lower Fraser valley and adjoining Coast mountains for the Geological Survey of Canada. The study, which is not yet completed, includes both bed-rock geology and geology of the unconsolidated sediments lying above bed-rock. In a rapidly expanding industrial area, .an advance knowledge of the geology may• greatly aid in future 'planning, and in many cases may .prevent not only the wastage of large sums of money, 'but possible disaster. Some of the present and future applications in which geological information in the Lower Fraser valley should be of value are as follows: the development of domestic, irrigation, industrial, and municipal groundwater supplies; drainage for industrial sites,, roadbeds, and farmlands; flood control along the Fraser river and smaller streams in the area; the location of dam sites, of major tunnels for water supply •and sewage, of road-beds, of foundation sites for large buildings .and other engineering undertakings in which geology may aid; the evaluation of oil and gas •possibilities; the production of building stone; and the production of sand and gravel, the subject with which this paper is primarily concerned."

Jan 1, 1953

By J. T. Kalala

The High Pressure Grinding Roll (HPGR) is gaining acceptance in the mineral processing industry and has become a competitive technology in reducing the specific energy consumption in Mineral processing plants. The amount of samples required for HPGR amenability testwork and HPGR wear tests is usually high and often cannot be available at early stage of projects were only a few drill cores are available. Although HPGR was initiated from small scale piston die compression tests, the development of small scale piston die test to predict the performance of HPGR has been slow. The objectives of this paper was to present the designs, operating procedure of piston-die press and operating conditions which have resulted in similar particle size distribution obtained from a piston die test and HPGR Labwal unit starting from the same feed size distribution. Testwork were conducted using a 2 MN piston-die press and a Labwal HPGR unit on major South African ore types, viz, gold, platinum and iron ores. The results obtained show that piston-die test can generate data to predict energy consumption, product size distribution, and even to evaluate the edge effect.

Jan 1, 2012

By R. M. Clowes

"As part of LITHOPROBE's multidisciplinary earth science research program to understand the evolution of the North American continent, studies have been undertaken in a number of key areas in Canada. In the Trans-Hudson Orogen of Manitoba and Saskatchewan, LITHOPROBE results require re-evaluation of tectonic models related to its origin. In the Abitibi greenstone belt of Quebec and Ontario, results indicate a more complex evolution for the southern Superior province, one that links with the development of gold and massive sulphide deposits. As part of the program, the seismic reflection profiling method is being adapted for the mining industry. Three examples demonstrate the subsurface information that can be obtained. In Noranda, the base of the volcanic Blake River group is imaged and reflectivity is tied to geology through well logs; in Matagami, the zone of mineralization is shown to be downdropped along a majorfault; in Sudbury, a new structural model is developed, one that shows marked asymmetry at depth and indicates that some ore-bearing units on the margins of the igneous complex may be repeated at depth. IntroductionLITHOPROBE is Canada's national, collaborative earth science research project, established to develop a comprehensive understanding of how the North American continent has evolved. Ten transects, or study areas, were chosen to investigate pivotal geological features to their deep lithospheric roots. They span the country from the Pacific to the Atlantic Oceans and from the U.S. border to the Yukon and Northwest Territories, and geological time from four billion years ago to the present. A multidisciplinary approach, which is spearheaded by seismic reflection techniques, is essential to developing complete interpretations and outstanding scientific results. LITHOPROBE also has pioneered the use and demonstrated the value of using reflection technology to determine subsurface geology in mining camps.This paper provides an overview of the transects and their significance for the tectonic evolution of North America. Two specific examples demonstrate how we detennine present three-dimensional lithospheric structure and past geotectonic processes which formed it. The application of the reflection method to imaging complex structures in ""shallow"" crystalline rocks has been developed with funding and other support from the mining industry and provincial geological surveys. Sustaining funds, however, are derived from the Natural Sciences and Engineering Research Council and Geological Survey of Canada. Emphasis has been placed on developing deeper penetrating tools for exploration of deeply buried, but economically retrievable, mineral resources near existing mines, where an expensive infrastructure already is in place. Three examples, Rouyn-Noranda in western Quebec, Matagami in northwestern Quebec and Sudbury in northeastern Ontario, illustrate these developments."

Jan 1, 1994

By Maurice Lauzon

"Aerial surveys of the open pits have been conducted regularly at Lake Asbestos of Quebec, Ltd. -a subsidiary of American Smelting and Re-fining Company -since 1958. Ground controls are supplied by Lake Asbestos, and a topographic map of the pits at a scale of 1 in. to 50 ft., with 2-foot contour intervals, is obtained by aerial photography. The information from the topographic map is then transferred by the Lake Asbestos engineering staff to sections from which the volumes removed are calculated. Considering the size and complexity of the operation, this system has proved to be the cheapest, fastest and most accurate way of determining the quantities of rock and overburden removed. More than 11,000,000 tons of ore and waste are mined each year in three different pits. Further-more, the nature, shape and extent of the orebodies make it necessary to mine on many (up to eight) benches of a pit during a single year. In addition, there are sections of the pits where it is impossible or un-safe to survey the crest of some benches by standard ground methods. For these reasons, the tonnages obtained by truck count are checked and adjusted by aerial survey. These surveys are now taking place every six months. With this system, it is possible for a two-man surveying crew to look after all field work in the mine area."

Jan 1, 1967

By SangHyeok Han

Selecting the best possible cranes and identifying spatial conflict-free locations on sites can result in productivity and safety improvements for large-scale industrial construction projects. In the current practice, experienced lift engineers select cranes based on the heaviest lift and/or the largest lifting radius of the identified crane. This practice is relatively time-consuming, and optimization of the crane?s use and location is also difficult. There are many factors which need to be considered during the crane selection process, a reality which further complicates the process. This paper presents a framework which aims at developing a decision support system to enhance the crane selection process and collision-free path planning for large-scale construction projects. This paper utilizes an innovative crane selection matrix in order to establish a process for optimized crane selection for construction projects. The study considers more than 40 different factors in order to reduce time and improve safety for crane operations. Following finalization of crane type (mobile crane versus tower crane), a visualization model to simulate crane operation and identify collision-free crane operation paths is proposed. This process can assist project managers to plan the lifting process more effectively and efficiently. A case study-based approach was utilized to demonstrate the proposed methodology. The methodology was tested in the planning and construction process for boiler house structures in Mannheim, Germany. The project entailed numerous challenges: one of the major tasks was to lift a 102-ton load on the top of the boiler structure through crane collaboration; space limitations on site also presented several challenges related to crane selection, location, and operation processes. Based on the project constraints, the proposed crane selection framework, and the visualization models, two tower cranes were selected and successfully implemented in the case study.

Aug 1, 2013

By J P. Bolduc, P. E. Pelletier

Preceded by brief general considerations such as the development of the mining industry in. the Province of Quebec, the choice of plant location, the types of problems studied etc., the paper gives a complete description of this new research and treatment center for metallic, non-metallic and asbestos ores. Facilities for carrying out operations in the three sections of the plant -the sampling section, the ore treatment section and the asbestos section -are fully discussed as well as laboratory facilities for (a) the preliminary testing of ores prior to pilot plant treatment and (b) the grading and testing of asbestos fibre. AT THE beginning of the century, the annual value of the mineral production of the Province of Quebec stood at the $2,500,000 level. Twenty-five years later, it was just under $24,000,000. In 1950, half a century later, it was slightly in excess of $200,000,000. But in 1959, in the span of only nine years, it

Jan 1, 1962

By A. West, F. Mohammadi

Growing awareness of selenium bioaccumulation has resulted in selenium management becoming an important environmental issue for mining operations. Selen-IX™ is a novel ion exchange based technology developed by BioteQ to provide an effective solution for removing selenium oxyanions from mine impacted water to single-digit µg/L levels. The technology offers significant potential benefits when compared to incumbent biological treatment processes, including substantially reduced capital and operating costs and significantly reduced production of a selenium-containing sludge for final disposal. This paper reviews the key features of the Selen-IX™ process and presents the results of recent pilot testing on selenium impacted water.

Jan 1, 2014

By M. U. Oko

"Monitoring of all the waste streams from Falconbridge's Sudbury Operations to determine whether they meet the required standards, has been performed for many years. By 1969, however, the number of samples being collected had become so large that a complete revision of the existing systemwas necessary. Sites previously designated by name only, were numbered, clearly marked on the ground and on maps which were circulated to all concerned. The types of pollutants analyzed were determined and specified for each sampling location and a chemical analysis report form was designed. The sampling schedule has been computerized to produce a periodic listing of the samples to be taken and the analyses required.An area map showing sampling sites, chemical analysis report form, spill report and a computer print-out example are shown and explained.EVOLUTION OF FALCONBRIDGE'S WASTEWATER. MANAGMENT SYSTEMFalconbridge Nickel Mines employs some 4500 people, operates nine mines, four mills and a smelter in the Sudbury basin. The operations are geographically fragmented into four widely separated locations, the Falconbridge operations east of Sudbury and the Onaping operations in Levack Township being the two largest of the four. The Lockerby area located to the west and the Lindsley Mine just north of Sudbury are now under development. The magnitude, the diversity and nature of the operations are such that constant vigilance is needed to prevent inadvertent damage to the environment. The purpose of this paper is to describe the information system used to monitor and control waste-water disposal on Falconbridge's properties to help ensure the maintenance of effluent standards satisfactory to the Ontario Water Resources Commission (OWRC) and to the Ontario Department of Health."

Jan 1, 1971

By R. A. King, B. G. Hunt, C. E. T. White

"This paper reviews the history, occurrence, properties, and uses of indium, and describes the commercial production and fabrication of that metal by The Consolidated Mining and Smelting Company of Canada, Limited (Cominco), at Trail, B.C'. Indium is produced commercially at Trail from dross retreatment furnace D.R.F.) slag, a complex by-product of the lead smelting operations. Furnace feed prepared from this slag is smelted with coke and limerock in an electric furnace. The e1ectric furnace bullion is parted electrolytically, producing a market-able lead-tin alloy containing about 8 per cent tin, and leaving the indium in the anode slime. Recovery of indium from the anode slime involves roasting the slime with sulphuric acid, followed by leaching with water, purifying the leach solution, recovering the indium by sponging with zinc or aluminum, and re-fining electrolytically. This process yields standard grade (99.97+ per cent) indium which is either sold or refined •to high purity ( 99.999 per cent) indium for special uses requiring higher purity metal."

Jan 1, 1959

By E. C. Roper

THE Britannia Mining & Smelting Company, Limited, have been operating their property at Britannia Beach, B.C., continuously for nearly forty years and have mined over 33,000,000 tons of ore from orebodies within a belt of highly sheared rocks, five miles long by 2,000 feet wide. The property is in the Coast Range mountains, about twenty miles due north of Vancouver. The mountains rise abruptly from sea level to elevations of 4, 500 feet within a horizontal distance of 7,000 feet. The topography has enabled the orebodies to be developed by adit tunnels. The active mining levels are connected to the adits by incline and vertical service shafts. The main service adits are the 2200, 2700, and 4100 levels (see Figure 1). The mine surface shops, three bunk-houses, and over one hundred dwellings form the townsite camp at the portal of the 2200 level adit. A small camp of one bunk-house and a few dwellings is situated at the 2700 level portal. The beach surface shops and camp, adjacent to the 4100 level adit, service the mill, foundry, and other beach installations as well as the mining from the 4100 level. The ore mined from the various orebodies is delivered to the 4100 main haulage level through a system of rock raises and intermediate tramming levels and is hauled on the 4100 level to the mill.

Jan 1, 1945

By C. W. Langenberg, D. E. Macdonald, R. S. Strobl

"The successful marketing of Alberta coals will increasingly depend, to a large degree, on an extensive coal quality information base. This information, at present, is generally based on a deliverable, cleaned coaland is confined to existing mine sites. Coal quality information is not as well understood for raw in situ coal outside of mine sites and even less is known about the geological factors that control it.If new uses and markets for Alberta coal are to be developed, such as gasification, coprocessing, and exploiting high rank coals for combustion, it will be imperative that the coal quality parameters important for these utilizations be known. These parameters need to be known for existing deliverable coals and, just as important, for as yet unexploited in situ coal. Factors such as the Cl, No, K, Co, P and trace element contents should be addressed to meet the requirements of these new utilizations.The geological characterization and explanation of what factors control these coal quality parameters is part of research being done at the Alberta Geological Survey. In-seam vertical profiling has been undertaken within the plains and foothills/mountains coals to determine exactly where coal quality variations occur and why. In the Ardley coal zone at the Highvale Mine it has been found, for example, that the ash content of the mined coal is made up of discrete partings and of microsized particles associated with inertinite macerals. The in-seam characterization of coal seams will lead to a better understanding of in situ coal quality variations, leading to new uses and markets for Alberta coal."

Jan 1, 1993

By Shek N. Lau, Nicola Samman

"Enclosed gear cases on board heavy mining equipment have traditionally been lubricated with regular heavy duty gear oils. However, equipment manufacturers, have recommended the use of an ISO-1000 gear oil for this application to ensure adequate lubricant film strength, especially at the higher end of the working temperature range. The majority of these ISO-1000 gear oils are based either on residual/asphaltic oil or synthetics, primarily higher viscosity polyalphaolefins. Although the performance of these lubricants has been satisfactory, they suffered other shortcomings that equipment users have lived with over the years.The major requirement at the user’s mine was to provide lubrication for the shovel Hoist gear case. Within such a gear case design, the gears and the roller bearings, that have different lubrication requirements, are lubricated with the same lubricant. Several lubricants were used, light gear oils as well as the recommended ISO-1000 heavy gear oils. On the one hand, the lighter oils performed adequately for the lubrication of the bearings that formed part of the enclosed gear system. These lighter oils did not perform as well for the lubrication of the gears due to their lower viscosities, resulting in shorter gear servicelives.On the other hand, the ISO-1000 gear oils performed well for the lubrication of the gears, but were too viscous to creep into the bearing elements to lubricate them adequately, especially during the cold northern Canadian winters. This resulted in catastrophic bearing failures and secondary damages to the gears.The challenge, then, was to formulate a lubricant which met the 1000 cSt at 40°C viscosity requirement as stipulated by the equipment manufacturer, while satisfactorily lubricating the bearings at the full working temperature range. This was achieved by the development of a semi-fluid grease lubricant, which has proven in field trials to give adequate performance in this application for the lubrication of both the bearings and gears down to -40°C.This product met the equipment manufacturer’s performance criteria and resolved, to a large extent, leakage of the lubricant through seals experienced with the use of conventional and synthetic gear oils.Although the main performance criteria of the fluid was its capability to lubricate the “Hoist” gear case, it was also used during the field trial in other gear cases on board the shovel to test its full capabilities.This unusual alternative lubricant was field tested and evaluated for more than two years. Based on this assessment, the product was reformulated to improve its fluidity, slumpability and the settling of debris/wear metals to the bottom of the gear cases. This reformulated softer grade, a semi-fluid grease, has been performing satisfactorily for more than eight months and is still undergoing longer term assessment."

Jan 1, 1996

By J. M. Ríos

"Without conscious effort and understanding, a number of factors unique to mineral exploration often hinder building sustainability in host communities. These include the episodic and transitory presence of an exploration team in the community and the inherent uncertainty of outcomes— most projects fail from an exploration perspective. Experience in rural communities across Mesoamerica, however, has shown that it is possible to go beyond pragmatic philanthropy and infrastructure improvements to promote positive, sustainable outcomes in communities. Examples are provided of lessons learned and proven practices that improve quality of life and support a strong social license to operate.RÉSUMÉ Sans une compréhension et un effort réfléchis, de nombreux facteurs uniques à l’exploration minérale nuisent souvent à l’établissement d’un développement durable dans les communautés d’accueil. Ces facteurs comprennent la présence épisodique et transitoire d’une équipe d’exploration dans la communauté et l’incertitude inhérente des résultats – la plupart des projets échouent après l’étape de l’exploration. L’expérience dans les communautés rurales à travers la Méso-Amérique a toutefois démontré qu’il est possible de dépasser la philanthropie pragmatique et les améliorations des infrastructures pour promouvoir des résultats positifs et durables dans les communautés. Des exemples qui améliorent la qualité de vie et soutiennent un solide permis social d’exploitation sont présentés; ils sont tirés de leçons apprises et de pratiques éprouvées."

Jan 1, 2015

By Ahmad Ghahremaninezhad, Denver H. Cowan

Much of today’s gold is locked within sulphide minerals. These sulphide minerals, including pyrite, need to be subjected to oxidative pre-treatment in order to leach the refractory-gold using traditional methods. Typically autoclaves employing high temperatures between 180?225 ºC, and extremely high pressures between 1,500?3,200 kPa, are used for the oxidative pre-treatment. However, the autoclaves themselves are very expensive, costly to operate and maintain, and produce excess sulphuric acid. This paper studies the atmospheric oxidation of pyrite in ferric sulphate solutions. In general, pyrite oxidation under atmospheric pressure can result in high elemental sulphur production, i.e. less acid generation. Activated carbon has displayed an ability to catalyze the process, achieving reasonable kinetics. The reaction kinetics were investigated by altering acidity of the leaching solution, temperature, catalyst ratio, sparged oxygen and agitation. A combination of X-ray diffraction, scanning electron microscopy, optical microscopy, X-ray fluorescence, inductively coupled plasma mass spectrometry (ICP-MS), and atomic absorption spectroscopy (AAS) were used to monitor the kinetics of the process and elemental sulphur yield. The purpose of this investigation was to determine optimal operating conditions that maximized kinetics of the atmospheric oxidation while maximizing elemental sulphur yield.

Jan 1, 2015

By Iwueze Anaekperechi Rose

The International Labor Organization has declared mandatory adequate provision of safe workplace and safety for all workers in all occupations including the mining sector. Early scientists like Agricola (1559) who studied the health of Miners, found that there are peculiar health problems associated to their work and working environment. This unsafe working condition was one of the major factors that resulted to the Industrial revolution in England and eventually led to the establishment of regulations and laws guiding operations in all workplaces and workers in England and all over the world. Recent studies by Heinrich suggested chains of events of safety issues in the mining sector. Occupational injuries, accidents and ill health have huge social and economic implications on workers, their families and communities. Top mining top issues are respiratory diseases, noise, explosives, ventilation, fire, and explosion. However, one of the principal mechanisms for achieving Occupational Health and Safety (OHS) goals and mapping the future is government regulations of employers. In Nigeria, the situation is not different; mining operations are equally hazardous and have far reaching implications. In 1995 the Ministry for Solid Minerals was established to focus on the development of other categories of mineral products ranging from gold, coal, uranium, and tantalum deposited across the country. Prior to this an Act of Parliament Act Cap 121 of 1946, was in place to regulate amongst other contents mining safety. This was subsequently reviewed following the incidence of Lead poisoning resulting from small scale miners processing gold ore highly contaminated with lead in Zamfara state (northern Nigeria). Hundreds of children died as a result of exposure to lead poisoning, it was clear that the regulations were not sufficient (details to be discussed). However, advances have been achieved in mining engineering since then. A review team was constituted to provide a more stringent law to regulate mining operations in Nigeria. The strategies for mapping the future of OHS in mining engineering will employ amongst others setting and adopting ISO/ILO standards and enforcement; providing technical assistance; and establishing sustainable developmental structures as surveillance and compensation. The management systems approach was also developed as a result of cases of accidents. The accepted international standards guidelines and requirements will be proposed. Furthermore in mapping the future for Mining Engineering, it is suggested that most countries have their own management strategies and legislation to improve safety of workers through greater consistency and efficiency of OHS programs. Some American researchers came up with the Safety Engineering Model. The Australian Mining Council of mineral and petroleum resources after the Catastrophic Maura Disaster developed the National Mine and Safety Framework. In Canada, after the Hillcrest mine disaster in 1914, Allan shaft coal mine catastrophe in 1918, Westray mine explosion in 1992 and other disasters, Occupational Health and Safety Act R.R.O 1990 was sufficiently developed to provide adequate safety conditions and standards. In Nigeria after the disastrous Zamfara lead poisoning, which claimed the lives of hundreds of children due to exposure and lack of appropriate safety measures, stringent measures were developed by the federal ministry of Justice to address and regulate mining process in Nigeria.

Aug 1, 2013

By David A. Edgecombre

This paper discusses modern practices in the extrusion of steel. Particular emphasis is given to a description of the Ugine Sejournet method of extrusion, involving the use of glass as a hot work lubricant. Other methods are also mentioned. A brief history of extrusion is presented; present practices in the quality extrusion of tubing and solids are described; and the future potentials of the) process as a tonnage producer are briefly discussed. The advantages of extrusion and the reasons for the use of a glass lubricant, as well as the various methods of using glass, are given. The process, as described, is being used in the manufacture of large commercial quantities of stainless steel tubing and sections. This extrusion process is an essential and unique means of forming such atomic-age materials as titanium, zirconium, molybdenum and other super alloys all of which are materials required in the creation of nuclear installations.

Jan 1, 1963