Search Documents

By Simon C. Dominy, Alwyn E. Annels, Paul Wheeler, Suzanne P. Barr, G. Simon Camm

Narrow veins are an important world-wide source of silver, tin, uranium and particularly gold. To potential ?nanciers, this style of mineralization is viewed as high risk because of the often relatively small resource involved and high cost of estimation. In many cases diamond core drilling will not enable resource estimation beyond the inferred and indicated categories. Exploratory under-ground development is required to de?ne measured resources. The de?nition of geological and grade continuity are major factors in narrow vein assessment. A measured resource must be based on strong geological and grade continuities. Narrow veins, generally less than 3 m wide, are complex geological phenomena, which commonly display unpredictable geometry and grade distribution. Variations in structural continuity, dip, strike, width, mineralogy and speci?c gravity are common. Veins may be composite, with ore-grade mineralization restricted to a speci?c structural domain. Branches, intersections and braided zones are common features. Potentially high-grade zones are often localized within ore shoots, which are surrounded by barren/low-grade regions. Resources must be determined as closely as possible to reality and re?ect the distribution of the commodity in the rock. Estimation has three main requirements: (1) geological study to determine orebody nature;(2) estimation of tonnage and grade, and (3) the presentation of this information using a classi?cation that is clear, unambiguous and bankable. Estimation methods employed are either classical or geostatistical; however, classical methods are often used because of the dif?culties in applying geo-statistics. Grades generally show a strong positively skewed distribution testifying the presence of high-grade values. Problems exist in the applicability of cutting outlier values risking over- or under-estimation of grade. It is generally believed that where resource estimates are in error, poor geological control is usually the cause. Overestimation can lead to the closure of a mine through lost revenue and capital. An understated estimate can result in an opportunity missed for pro?t and/or greater economies of scale. De?nition of reserves involves the consideration of economic and engineering data, to decide which part of the resource is economically mineable. Geology plays a similarly important role at this stage in the assessment of likely mining method, dilution, recovery etc. Throughout resource/reserve estimation, it is crucial that the amount and quality of the data and the geologist’s experience are relevant. The impact of geological understanding on estimation is often undervalued or assumed to be of lesser importance than ?nding grades and tonnages. This paper discusses the geology of narrow vein deposits and the importance of geology in their evaluation.

Jan 1, 1997

By Simon C. Dominy, Alwyn E. Annels, Paul Wheeler, Suzanne P. Barr, G. Simon Camm

Abstract-Narrow veins are an important world-wide source of silver, tin, uranium and particularly gold. To potential financiers, this style of mineralization is viewed as high risk because of the often relatively small resource involved and high cost of estimation. In many cases diamond core drilling will not enable resource estimation beyond the inferred and indicated categories. Exploratory underground development is required to define measured resources. The definition of geological and grade continuity are major factors in narrow vein assessment. A measured resource must be based on strong geological and grade continuities. Narrow veins, generally less than 3 m wide, are complex geological phenomena, which commonly display unpredictable geometry and grade distribution. Variations in structural continuity, dip, strike, width, mineralogy and specific gravity are common. Veins may be composite, with ore-grade mineralization restricted to a specific structural domain. Branches, intersections and braided zones are common features. Potentially high-grade zones are often localized within ore shoots, which are surrounded by barren/low-grade regions. Resources must be determined as closely as possible to reality and reflect the distribution of the commodity in the rock. Estimation has three main requirements: (1) geological study to determine orebody nature; (2) estimation of tonnage and grade, and (3) the presentation of this information using a classification that is clear, unambiguous and bankable. Estimation methods employed are either classical or geostatistical; however, classical methods are often used because of the difficulties in applying geostatistics. Grades generally show a strong positively skewed distribution testifying the presence of high-grade values. Problems exist in the applicability of cutting outlier values risking over- or underestimation of grade. It is generally believed that where resource estimates are in error, poor geological control is usually the cause. Overestimation can lead to the closure of a mine through lost revenue and capital. An understated estimate can result in an opportunity missed for profit and/or greater economies of scale. Definition of reserves involves the consideration of economic and engineering data, to decide which part of the resource is economically mineable. Geology plays a similarly important role at this stage in the assessment of likely mining method, dilution, recovery etc. Throughout resource/reserve estimation, it is crucial that the amount and quality of the data and the geologist’s experience are relevant. The impact of geological understanding on estimation is often undervalued or assumed to be of lesser importance than finding grades and tonnages. This paper discusses the geology of narrow vein deposits and the importance of geology in their evaluation.

Jan 1, 1997

By G. M. Behrend

"The mining and processing of mineral ores is a very old industry which is steeped in tradition. Rising demand for metals has recently forced the exploitation of lower-grade orebodies which require extensive beneficiation. The high capital expenditures involved, together with market pressures for high-quality concentrates and pellets, have forced the development of new process technologies which are heavily dependent on automatic process control. Development of suitable instrumentation has been rapid and it is being applied to mining processes today with a high degree of sophistication. The drive for higher efficiency and profitability goes on and has reached a level at which modern digital computers appear to be the only answer. However, the efficient application of a digital process computer is extremely complicated and is therefore approached by the mining industry with considerable hesitation.Some of the benefits promised by the digital computer can be obtained today by other means, which are more manageable and can provide immediate payoff. The result would be a building-block system which would utilize the digital process computer as its final component, to perform true plant optimization, free from routine chores."

Jan 1, 1971

By Alessandro Navarra, Roberto Parra, Boyd Davis, Frank Mucciardi

A smelter scheduling algorithm has been developed, which allocates the oxygen production between the smelting furnace and the converter aisle, so as to maximize copper throughput. The algorithm is intended for daily operation planning, controlling the sequencing of the converter cycles, and the oxygen drawn by these cycles. In some cases, it may be worthwhile to decrease converter oxygen allocation in favour of the smelting furnaces. Thus, a better utilization of the oxygen plant can increase primary copper throughput by several percentage points. This principle is demonstrated through sample computations. The approach presented in this paper can be incorporated into smelter management software.

Jan 1, 2015

By Dao Dac Tao

The Vietnam coal industry in recent years has achieved the rapid growth. However, in the process of industrialization and modernization of the country, the demand for coal for energy is constantly increasing. This paper presents the Vietnam coal industry in the last stage: the opportunities and challenges facing the coal industry as it strives to become modern, highly effective and capable of meeting the demands of national energy security, all in harmony with socio-economic and environmental needs.

Aug 1, 2013

By Mauro Torres, Gabriel Zarate

"AngloAmerican used the extractant M5640 at Mantos Blancos and Mantoverde and uses PT5050MD at Los Bronces Division, which are aldoxime and modifier blends. In the first case, the modifier is the esther TXIB, while in the second case is the tridecanol TDA. It is a well-known fact that the extractant degrades while the modifier does not and with time the oxime/modifier ratio can change significantly, depending on the operating conditions of each plant.In order to evaluate the effect of this varying modifier content in the plant organic, especially in the organic losses, a complete metallurgical test work program was conducted at laboratory and pilot plant scale by Flomin SNF, a new extractant supplier. Results showed that the addition of an aldoxime without the modifier did not affect the chemical performance of the extractant, but there was a significant decrease in the viscosity and density of the organic.Based on the results obtained in the metallurgical program, it was decided to run plant scale tests at the SX plants of Mantos Blancos and Mantoverde. In these tests, instead of adding extractant to maintain the organic inventory, CuPROMEX 3406 which is an unmodified aldoxime was added until the original oxime/modifier ratio was reached. This was obtained after 6 months of operation and since then both plants are running with the extractant CuPROMEX 3302 both supplied by Flomin SNF.In the case of Los Bronces, the pilot plant work was completed and it is programmed to run similar plant scale tests. In this case, the oxime/modifier ratio increased and TDA will be added until reaching the original ratio.The plant results obtained at Mantoverde and Mantos Blancos, together with the pilot plant test results obtained at Los Bronces, are discussed in this paper."

Jan 1, 2016

By D. Roy Eccles

A multi-element geochemical response, with contrasts of up to 29 times background, was obtained in soil above the Mountain Lake Diatreme, northwestern Alberta. The overall geochemical signature is indicative of an ultramafic source; geochemical responses contain elevated concentrations of Co, Cr,O, Cu and Ni with the presence of high Ba, Ga, HI, PO,, Rb, Ta, Ti and light rare earth elements suggestive ofa kimberlite or lamproite body. The shape, or morphology, of the enzyme leach-based geochemical signature over the Mountain Lake Diatreme combines moderately strong to strong oxidation halos, or a rabbit's- ear geochemical profile, with a sharply-defined apical geochemical profile. Because some Alberta diatremes discovered to date form positive topographic highs, the resultant geochemical signature may express the soil development profile that forms directly on top of kimberlitic and lamproitic bodies. The enzyme leach technique, which has proven to be a useful tool in base metal, precious metal and petroleum exploration, may have a significant impact on exploration for kimberlite, lamproite and related rocks in Alberta by providing industry with a useful and cost effective tool to probe blind and/or buried anomalies identified by airborne and ground magnetic surveys in areas of glacial overburden.

Jan 1, 2001

By E. Howard Lambert

"Operating costs of mining plants are increasing due to the increased cost of labour, materials and fuels. Labour and materials costs are factors not readily controlled. However, the use of energy from fuels may be controlled by plant operations. This paper describes the fossil fuels, their expected rate of depletion and their costs. The paper considers methods which may be used to provide an efficient use of energy from fuels. It includes an outline of obtaining energy, as heat, from mine milling operations (air compression) and obtaining the maximum use of energy from fuels used to generate electricity."

Jan 1, 1973

By D. Gagnon, B. Dubreuil, J. -M. Lalancette, D. Lemieux

"The pilot scale extraction of gold with a brine of sodium chloride and bromide at 30 ºC, in an atmosphere of halogens at atmospheric pressure, leads to gold chloride with 95% gold recovery. The use of dilute hypohalites (1 – 3%) instead of free halogens, which is strong enough to oxidize hypobromite into bromine, simplifies the recycling of halogens by electrolysis. With the recycling of water and brine, the regeneration of hypohalites and with a barren solid that is inert and stable. The Nichromet Extraction technology is a green process where the protection of the environment does not preclude profitability.INTRODUCTIONThe use of chlorides for the extraction of gold predates the discovery of chlorine by Scheele in 1774. In the Plattner chlorination process (Christy, 1888) sodium chloride and copper salt were used to promote gold recovery by amalgamation with variable results. The introduction of the cyanide technology in 1889 has led to a general use of this method for gold recovery. In the last decades, a return to chlorine in extractive processes has been noted (Ferron, Fleming, O’Kane and Dreisinger, 2002), mostly because of environmental pressure for non-cyanide technologies.This paper describes a closed circuit proprietary approach (Lalancette, 2009) developed and piloted by Nichromet Extraction Inc. for the extraction of precious metals with recycled mixed halogens; chlorine and bromine from hypohalites. DESCRIPTION OF THE PROCESSThe attack of gold by halogens can vary significantly. The rate of reaction is substantially higher with bromine (Br2) than with chlorine (Cl2), by a factor of more than five, although the oxidation potential of Cl2 is higher than Br2, as shown in Equation 1a and Equation 1b (Latimer, 1952)."

Jan 1, 2012

By Fathi Habashi

"Hydrochloric acid (HCl), although more expensive than sulfuric, find uses as a leaching agent in reactions involving iron oxide. The reason for this substitution was the discovery that oxyhydrolysis of ferrous chloride by which HCl can be recycled economically. This avoided the pollution of the environment by ferrous sulfate. It was found further that the rate of leaching of sulfides is faster when HCl is used as compared with sulfuric apparently due to the formation of aqueous chlorine. In case of refractory gold ores, HCl leaching under pressure avoids the use of cyanide solution since gold chloride is produced which can be recovered by standard methods. Hydrochloric acid find also uses in the leaching of scheelite and apatite but its use in leaching clay and anorthosite is questionable.INTRODUCTION Sulfuric acid is the cheapest acid and is used as a leaching agent in many hydrometallurgical processes. However, hydrochloric acid (HCl), although more expensive since it is prepared by reaction of sulfuric with sodium chloride, has replaced sulfuric acid in many reactions involving iron oxide. It replaced sulfuric acid for the first time in 1960s in pickling of steel because of pollution problems (Habashi, 2000). Ferrous chloride produced in pickling can be economically decomposed to ferric oxide and HCl according to:2FeCl2 + 2H2O + 1/2O2 ? Fe2O3 + 4HCl (1)which also shows that the acid can be regenerated but ferrous sulfate cannot be economically decomposed to recover sulfuric acid for recycle. Since then, HCl has been used in many leaching processes. Hydrochloric acid is a corrosive acid and is usually handled in rubber-lined equipment. REGENERATION OF HYDROCHLORIC ACID Regeneration of HCl is conducted in fluidized bed or in spray roaster Fluidized bed oxyhydrolysis In a fluidized bed, ferrous chloride solution is introduced onto a bed of hot ferric oxide where heating is provided by the hot fluidizing combustion gases (Figure 1). The solution is fed on top of the bed of oxides. The liquid feed wets the outer layer of the hot oxide particles and is quickly evaporated to form a layer of new solid oxide on top of the existing oxide, thereby producing dense homogeneous particles."

Jan 1, 2017

By C. H. Ash

"The Red Chris Cu-Au deposit (522.7 Mt at 0.35% Cu and 0.27 g/t Au), northwestern British Columbia, is one of several pre-accretionary porphyry systems in the Cordillera of westernCanada. It is hosted by an Early Jurassic hornblende monzonite to quartz monzodiorite porphyry which forms part of a suite of dikes and stocks that intrude Late Triassic volcanic strata. Major and trace element chemical data suggest that these Early Jurassic intrusions have compositions which fall on the boundary between alkalic and calc-alkalic compositions. Alteration and mineralization in the Red Chris deposit are more typical of calc-alkaline porphyry systems with abundant potassic, sericitic and argillic assemblages and quartz-rich stockworks. It lacks Na- and Ca-bearing silicate assemblages which characterize the alkalic porphyry deposits of British Columbia. One of the more unusual features of the deposit is the abundance of carbonate alteration and veins which occur throughout the hydrothermal history of the deposit. This type of alteration and veining is more typical of alkalic porphyry deposits.The composition of the carbonates vary both temporally and spatially with different alteration zones. Potassic zones, which are characterized by orthoclase±albite±quartz±chalcopyrite±bor-nite±magnetite±hematite and Au/Cu ratios of 1:1 (g/t Au:% Cu), contain minor siderite veins and alteration. Quartz-sericite-carbonate (QSC) zones overprint earlier potassic alteration and comprisequartz+ankerite+sericite+pyrite+chalcopyrite with Au/Cu ratios of 0.5:1 (g/t Au:% Cu). Ankerite isthe main carbonate in this stage but has a variable composition with a more Fe-rich variety associated with mineralized veins. Localized chlorite-carbonate alteration zones, characterized by chlorite+carbonate+quartz±kaolinite±pyrite±gypsum and high Au/Cu ratios [2 to 3.5:1; (g/t Au:% Cu)],contain predominantly calcite. Late stage carbonate-gypsum veins have an ankerite to dolomite com-position which is very similar to the regional carbonate alteration and veins."

Jan 1, 1997

By Sunil S. Gandhi

"Uranium occurrences are widely distributed in tuffaceous-argillaceous beds and abundant rhyolitic volcanic rocks of the upper Aillik group, which is more than 3 km thick and over 125 km by 40 km in areal extent. They include partially developed Kitts and Michelin deposits, containing 1560 and 7366 t U respectively.Uranium occurs mainly as disseminated fine pitchblende grains in beds and lenticular stratabound zones, and rarely as coarse pitchblende aggregates and thin veinlets. The Kitts deposit and ten other occurrences are in the argillaceous-tuffaceous beds within a steeply dipping stratigraphic zone, less than 50 m thick and over 20 km long, at the base of the upper Aillik group. The occurrences hosted by the rhyolitic rocks, numbering over fifty and including the Michelin deposit, are in elongate structural-stratigraphic belts or zones, and are characterized by a pronounced enrichment of soda and depletion of potash associated with mineralization. The mineralized zones are affected to a varying degree by Hudsonian deformation, metamorphism and granitic intrusions.The uranium mineralization is interpreted as genetically related to the felsic volcanism, involving syngenetic deposition in argillaceous-tuffaceous beds and epigenetic emplacement in rhyolites. The volcanic activity occurred 1855 ± 5 Ma ago according to a preliminary U-Pb zircon date on porphyritic rhyolite. Pitchblendesfrom the Kitts and Michelin deposits and a few other occurrences in rhyolites have yielded nearly concordant dates in 1810 to 1730 Ma range. They reflect resetting of isotopic equilibrium at the time of Hudsonian deformation. Other isotopic data on pitchblendes and galena from veins and aggregates .in the south near the 'Grenville Front' indicate local redistribution of uranium and radiogenic lead at the time of Grenville Orogeny approximately 1100 Ma ago."

Jan 1, 1986

By H. J. Chalmers

THE H.B. MINE and concentrator are located in the Nelson Mining Division of British Columbia, on the north side of the Sheep Creek valley about seven miles southeast of the town of Salmo. It is an operation of The Consolidated Mining and Smelting Company of Canada, Limited (Cominco), which has its metallurgical plants at Trail, about 25 miles west. The property was originally staked about 1907 by Horton and Benson, whose names are commemorated in the designation "H. B." Up until 1927, a considerable amount of development work was done in the upper levels by various companies. Cominco purchased the ?property in 1927 and carried out intermittent work until 1946. Following this, an extensive surface diamond drilling programme and a subsequent underground exploration were undertaken. Sufficient ore was outlined 'to warrant the construction of a 1,000: ton concentrator. This was started in April, 1952, and completed by the spring of 1953. However, because of adverse base metal market conditions, operation was deferred until May, 1955.

Jan 1, 1957

By Alain Grenier

To be more competitive, we have to try new mining techniques. A few of them are: extend honghole length increase drilling precision new type of primary opening (slot) use of CMS to extend stope length This paper will cover our trials, successes and failures and will cover a few real cases that occurred at the Doyon mine.

Oct 1, 2001

By J. Grignon, C. Fleming

It is possible to reproduce the performance of an operating CIP or CIL plant in the laboratory, in small scale batch kinetic tests, coupled with mathematical models that translate kinetic data into predicted steady state gold profiles across multi-stage adsorption circuits. Once the performance of the commercial plant has been mimicked by the model, the plant operating parameters can be varied systematically in the model, and the likely response of the plant to the step wise change can be determined. In this way it is possible to inexpensively optimize the operating conditions of an existing plant, with no disruption to plant operations and no economic risk to the mining company. This approach had been adopted by IAMGOLD to optimize the performance of their Rosebel CIL plant following several major expansions in mill capacity since 2004.

Jan 1, 2011

By G. A. Fenton, A. Vervoort, M. Alvarez Grima

"High-risk underwater mining operations necessitate characterizing spatial heterogeneity and resource uncertainty. Local average subdivision is a method of simulating spatial deposit variability inside a cell through a sequence of discretization stages, during which a cell is further subdivided into four or eight cells. New developments are presented to validate simulated deposit models and deal with point measurements of geotechnical and ore-grade properties. This paper illustrates the relevance of translating spatial deposit variability into financial or operational performance indicators during underwater resource exploitation. Two synthetic case studies highlight the challenges of underwater mining in relation to production plans and equipment selection.RÉSUMÉ Les opérations d’extraction minière subaquatique à risque élevé exigent une caractérisation de l’hétérogénéité spatiale et de l’incertitude de la ressource. La moyenne locale de subdivision est une méthode de simuler la variabilité spatiale du gisement dans une cellule par une séquence d’étapes de discrétisation durant lesquelles une cellule est subdivisée en quatre ou huit cellules. De nouveaux développements sont présentés afin de valider les modèles de simulation des gisements et de traiter des mesures ponctuelles des propriétés géotechniques et de teneur du minerai. Le présent article illustre la pertinence de traduire la variabilité spatiale du gisement en indicateurs de rendement financier ou opérationnel durant l’exploitation subaquatique de la ressource. Deux cas synthétiques soulignent les défis de l’exploitation minière subaquatique par rapport aux plans de production et de choix des équipements."

Jan 1, 2015

By A. H. C. A. Zimmerman

WE have just heard what must be regarded as a thoughtful, constructive and somewhat painful analysis of the financial function of our industry. While thinking about this, it is interesting to reflect on the conditions which have stunted the growth of the financial side of our affairs. Mining must be regarded as a wealthy business. •while immeasurable grub takes and development budgets have been lost, there can be little argument that a productive ore-body nearly always produces the type of wealth that breeds some extravagance. I recognize that this statement can be attacked from many sides, but an historical comparison with a commercial enterprise involving similar investment will demonstrate what I mean. However, these old times are be-ginning to disappear for a variety of reasons. High amongst these are: ( l) Increased costs of exploration. (2) Remoteness of many new finds. (3) Fixed or declining metal prices (particularly when expressed in constant dollars). ( 4) Constant demands for higher wages.

Jan 1, 1962

By Robin Sheremeta

What is the goal of every organization when it comes to safety? Everyone Going Home Safe and Happy Every Day Good old days: Era of Death (accidents will happen) Era of Engineering: (Eg. hand rails, limitswitches, machine guards, etc.) Era of Legislation: procedures, laws and regulations (Eg. SWP?s, Mines Act) Era of Behaviour-Based Safety: (eg. STOP program)

May 1, 2010

By J. R. Shouldice

"IntroductionREEFS of Silurian age are recognized in southwestern Ontario, both in outcrop and from subsurface information. This paper deals with the so-called 'pinnacle' reefs which are known only in the subsurface. For the purpose of this paper, the pinnacle reefs are arbitrarily defined as those structures having a height of over 250 feet and a length of less than two miles. This definition eliminates numerous mounds and other broader, more subdued, structures of less certain origin, found in subsurface beds.The term 'pinnacle reef' is perhaps unfortunate, but it is in common usage in Ontario and is used elsewhere for different types of reefs. A new name is justified by the unusual environment and structure of the Ontario reefs, but it is unlikely that any other term would gain acceptance. Rather than propose a new term which would be ignored or result in further confusion and misuse, the name 'pinnacle', as defined above, is used in this paper.Pinnacle reefs have been found over a fairly large part of southwestern Ontario. The known reefs of this type parallel the southeast edge of lake Huron and •follow the strike of the structure contours which circle the Michigan basin (see Figure 1). In total, twenty-five such reefs have been discovered in southwestern Ontario."

Jan 1, 1955

By D. M. MacLean

THE property of Howey Gold Mines, Limited, is situated at Red Lake, Ontario, one hundred and seventy-five miles east of Winnipeg and eighty miles north of the Canadian National railway. The mine has been a continuous producer since April, 1930, and, at present writing, a total of 3,042,690 tons has been hoisted, giving a production of $6,422,858.55, for a grade of $2.32 per ton. From 1,064,477 tons mined during the past two years, however, the yield has been only $1,389,607.03, or $1.41 per ton (gold at $20.67). Present output is at the rate of about 1,470 tons. per day. THE ORE-BODY AND WALL-ROCK: The Howey ore-body is part of a quartz porphyry dyke, which has. intruded an area of greenstone. The dyke strikes north 65° east, and its dip varies from 85° to the south at the surface to practically vertical below the. 1,000-foot horizon. Both along the strike and on the dip, the width of the dyke varies from 25 to 200 feet, the widest portion occurring below the 1,000-foot level. To the east of the ore-body, the dyke increases in width and finally splits into tongues of porphyry enclosed in greenstone, diorite, and congloJ11erate. To the west, it passes into the adjoining property, its width at the boundary being 100 feet. The rock in the ore-body is hard to drill, but, because of numerous horizontal slip-planes, it breaks well when blasted. This characteristic makes it possible to break large breasts or benches with a relatively small number of holes. The ore broken in this manner is consequently quite coarse, a large part of it requiring secondary breaking.

Jan 1, 1938