Search Documents

By K. E. Barnes

"The IsaMill was developed for fine-grained ores that required at least double the grinding efficiency of ball or tower milling to be economic. This was achieved, but in practice, the benefits of using inert media (eg sand, slag, ore, ceramic) have proven to be at least as important as the higher grinding efficiency. Flotation selectivity and rate was improved for all particles, particularly fines. This allowed a dramatic simplification of the Mount Isa lead zinc flotation circuit – adding 6 MW of ultrafine grinding power reduced reagent addition and flotation volume and increased plant energy efficiency. This was quite unexpected.This paper examines four orebodies that were enabled by inert grinding – McArthur River, George Fisher and Black Star Open Cut Mines (complex fine-grained lead zinc orebodies in Australia), and the Western Limb Tailings Retreatment plant (a PGM operation in South Africa). In a unique case history, the operating performance of the Mt Isa lead zinc concentrator is explained by size-by-size mineralogical data collected over 25 years, systematically explaining the impact of declining ore quality, and the effects of additional conventional grinding, inert grinding, and circuit and reagent redesign.The mineralogical case histories are so compelling that it is argued that the advantages of inert grinding should not be confined to difficult, fine-grained orebodies. The availability of largescale efficient inert grinding mills could have profound impact on circuit design for many orebodies.INTRODUCTIONThe IsaMill was developed by MIM (now Xstrata) to enable the development of the McArthur River Orebody in the Northern Territory of Australia. This ultra-fine grained ore needed a grind size of 80% passing 7 microns to produce a saleable concentrate. Such a fine grind was not economic with conventional ball or tower milling. Below about 25 microns the low energy efficiency and high media consumption of these mills is prohibitive. Critically, the high steel consumption and associated change in pulp and surface chemistry also seriously affects flotation metallurgy."

Jan 1, 2006

By R. Dahlke, J. A. Finch

"A campaign was undertaken during the greater part of 2001 at Noranda’s Brunswick Mine Concentrator to investigate the role of gas (air) superficial rate distribution (Jg profile) to the cells in the final Zn cleaning stage (bank of seven cells). Three profiles were tested: Balanced (each cell with same Jg), Increasing (from cell 1 to 7), and Decreasing, along with an “as found” profile in a parallel control bank. The experimental design allowed for two confounding factors, changes in ore type and circulating load. The Increasing profile consistently gave the best metallurgy (down-the-bank grade / recovery). The reason for improved performance was traced to the response of the first few cells. The Increasing profile gave the highest selectivity of sphalerite against non-sulphide gangue (NSG) in these cells with relatively even recovery per cell down the bank (10-15% based on feed to each cell). The other profiles gave lower selectivity and higher zinc recovery in the first cells (up to 25% in cell 1), which combined to reduce overall bank performance. The increased selectivity with the Increasing profile is attributed to the low gas rate in the first cells reducing water recovery and hence limiting entrainment of NSG gangue. The Increasing profile was subsequently configured for all four stages in the zinc cleaner circuit.INTRODUCTIONThe performance of a flotation circuit is largely the result of the operator’s response to visual clues. This includes manipulation of the gas (air) input and how it is distributed to cells in a bank. A lack of sensors prescribes this approach. Over the past ten years the Mineral Processing Group at McGill University have developed a set of gas dispersion sensors including one to measure gas superficial rate (or simply “gas rate”), i.e., volumetric gas rate per unit cell crosssectional area, Jg (Gomez and Finch, 2002). The device collects bubbles in a tube immersed in the pulp and infers Jg from the pressure-time curve generated after a valve is closed and air starts to accumulate. The usual units are cm/s. It is robust, reliable and suited for plant use.A version of the Jg sensor was tested extensively during 2000 at Noranda’s Brunswick Mine Concentrator (Dahlke et al., 2001). The results were sufficiently encouraging that a sensor was fabricated to suit local requirements (Insta-Jg). The sensor detected malfunctioning field instruments and flotation mechanisms, and demonstrated that gas distribution to cells in a bank “as found” had no particular pattern, or profile. Preliminary testing suggested that a balanced profile (i.e., all cells with the same gas rate) gave superior metallurgy (grade / recovery down the bank) than the “as found” profile. This observation prompted a focused campaign to explore the impact of the gas rate (Jg) profile, introducing the notion of “gas distribution management”."

Jan 1, 2004

By Paul Hughes

This paper summarizes current underhand paste backfill mining as applied to Goldcorp Inc?s Red Lake Mine, Newcrest Mining Ltd?s Kencana Mine and the Lanfranchi Nickel Mine as well as ongoing research at the University of British Columbia?s Norman B. Keevil Institute of Mining Engineering. The Red Lake Mine utilises a 6 m wide undercut with a 2 MPa unconfined strength paste in order to selectively mine its high grade, high-stress orebody. Kencana?s orebody is located in a poor rock mass environment. An 8 m wide, 2 MPa unconfined strength paste sill allows a safe working condition for its high grade orebody. The Lanfranchi Nickel Mine utilises a cable-supported, 2 MPa paste, with 12 m span sills, to optimize the mining of the squeezing rock mass. This paper details the rock mechanic hazards, ground support techniques, paste practices and unique conditions for each mine. Further, an update of ongoing research at the University of British Columbia, focussing on the optimization of safe mining in underhand cut-and-fill mining in high-stress/weak rock masses, is presented.

May 1, 2011

A key point in the manufacture of cemented backfill is the dewatering and settlement of the total tailings product. A new technology characterized by rapid non-mechanical settlement of total tailings has been developed based on a large number of laboratory and field tests, where dynamic settlement and continual slurry preparation of total tailings in a vertical sand silo are realized by the addition of an effective flocculating agent named NPA. It has been shown that the sedimentation velocity of the interface between total tailings and water after NPA was added is 10 to 20 times higher than that without any flocculating agent, that the mass fraction of sand slurry deposited at the bottom of the vertical sand silo reaches 70%, and that the solid particle content in effluent waste water meets national water quality standards. The simple devices used to add flocculants have little deleterious effects on the current preparation tank and have been tested in an industrial environment. The processing cost of total tailings by the new technology is only 10% to 20% of that required for mechanical settlement.

May 1, 2007

By M. Massinaei, S. Abasi, M. Oliazadeh

Reliable measurement and control of the pulp-froth interface (froth depth) in the flotation columns is critical to achieve the desired metallurgical performance. Shallow froths result in a reduction of grade because of particle entrainment and deep froths reduce recovery because of the drop back of entrained and weak hydrophobic particles to the pulp zone. The cleaner circuit at Miduk copper concentrator consists of three parallel MicrocelTM flotation columns 4 m in diameter and 12 m in height. The interface level of the flotation columns is measured by two pressure sensors located at 1.4 and 2.4 m from the cell lip (in the collection zone). In this study the performance of the level detection system at different operating conditions was evaluated. A calibrated float-ultrasonic location system was used for measuring the actual froth depth. The results indicated that the existing level control system was subject to considerable error. The absolute error was found to be 33.27 cm. This was mainly attributed to the constant set-point value assigned to the froth density (ρf=0.3 g/cm3), which actually varies with the operating conditions. The actual froth density at different conditions was calculated and its average value (ρf=0.12 g/cm3) was re-set in the control system. This resulted in substantial reduction in the level-detecting error. Recommendations for more accurate measurement of the interface level were presented. INTRODUCTION Froth flotation is a complicated process because of many involved variables. One of the most significant controlled variables in the flotation process is the pulp-froth interface (froth depth). The froth depth has a profound influence on the metallurgical performance parameters (i.e. grade and recovery). Shallow froths result in grade reduction because of particle entrainment and deep froths reduce recovery resulted from the drop back of entrained and weak hydrophobic particles to the pulp zone (Finch and Dobby, 1990). Various techniques have been developed for measuring the interface level of the flotation cells in the last few decades. These techniques can be classified as: Techniques based on hydrostatic pressure measurements (Finch & Dobby, 1990), Techniques based on the density gradient (float) (Moys & Finch, 1988), Techniques based on conductivity measurements (Uribe-Salas, 1991), Techniques based on temperature measurements (Moys & Finch, 1989).

Jan 1, 2019

By Eldridge Haynes

IF you ask the average American to define 'total war' he is apt to fumble for an answer. But in Britain everyone knows the answer, because Britain has mobilized its total labour force, including women. If we were to match, proportionately to our population, Britain's mobilization of labour, we should have 60,000,000 people working full time in the armed services, civilian defence, and war industries. Actually we have fewer than 35,000,000 so employed. In Britain two out of every three persons between the ages of fourteen and sixty-five are so engaged. For the first time in the history of any democracy Britain conscripts women for service in the army, navy, and air force. Two hundred thousand British women have been conscripted for the army, known as ATS, meaning Auxiliary Territorial Service. There are more women in the air force than the total personnel of the RAF at the outbreak of the war and almost all of the land base jobs of the British navy are now handled by women. In addition to cooking and office work, Britain's women soldiers and sailors are driving trucks and motorcycles, repairing motor vehicles, packing and repacking parachutes, installing, inspecting, and maintaining gun equipment and ammunition of combat planes after each raid, raising and lowering barrage balloons, forecasting weather, manning harbour craft, sending and receiving radio messages. A normal ack-ack unit is composed of 229 women and 189 men. The women man the gun height finders and predictors, give bearings, and signal to fire.

Jan 1, 1942

By Christoph Mueller

Mining operations are characterized by cost pressure and cycling product prices. A high potential for enhancing efficiency is the integration of all single steps of the mining working chain into a production process structure to make advantage of an optimized flow of material and information through the ?moving ore factory?. As modern mining machinery today is controlled electronically and even already operated autonomously, a smooth and cost efficient flow of data in the mining process will be crucial for cost efficient future mine operations. Therefor, the International Rock Excavation Data Exchange Standard (IREDES) was launched by major players in the industry. The task of this initiative is to define a ?common electronic language? for easy and standardized data exchange between mining machines and central computer systems. As in other industries, this standard is expected to have significant impact on the use of automated equipment. It shall provide easy ways of using multi vendor machine installations in data controlled mining processes. At the same time it reduces cost for individual development of interfaces for all parties involved. Standardized data exchange is also a crucial precondition to integrate the mining process into enterprise level modeling, cost analysis and decision finding systems. The standard?s technical architecture is open and flexible for future applications. It uses modern XML technology enabling easy data exchange with commercial databases as well as open on line networking. The IREDES work is carried out by the initiative members working jointly together in the technical work groups. Prototyping implementations of the Drill rigs profile are currently going on. Further profiles under development cover LHD?s/Loaders/Trucks and Explosives Chargers. The first official release covering the Drill Rigs profile is planned for the end of 2002.

May 1, 2002

By Brigitte Lacouture, Yeen Shien Hwang, David Lin

"A baseline survey of the partially open lead regrind circuit at Red Dog Mine indicated poor regrind efficiencies for the three parallel 450 HP tower mills. Driven by the high energy cost and the potential metallurgical gain brought by improved mineral liberation, the Red Dog lead regrind circuit was optimized in two stages.In the first optimization stage, different circuit layouts were evaluated in two plant trials. In June 2003, the regrind circuit was changed to a fully closed circuit. This reduced the tower mill requirement from three to two mills. The circuit modification payback was 11 days through power savings alone.The second stage of optimization was the evaluation of reagent addition. To improve pyrite depression, sodium cyanide was added to the feed of the lead regrind tower mills and tested in a series of plant trials over several mill feed stockpiles. Galena selectivity against pyrite was found to improve in these plant trials. Due to environmental sensitivities, no net increase in cyanide addition to the plant occurred and thus no increase in the cyanide concentrations in the tailings pond or the environment will result.The lead regrind optimization work improved the overall lead metallurgical performance and reduced energy and reagent costs. Economic analysis showed that annual profit increased by as much as US$3.0 M."

Jan 1, 2005

By Bruce Mennie

PT Freeport Indonesia (PTFI) operates copper and gold mining operations in a mountainous area of the Mimika regency, near Tembagapura, Papua (formerly, Irian Jaya), Indonesia. The mining and concentrating operations typically produce 240,000 metric tonnes per day of Copper and Gold ore from the combined mining of an 80,000 tonne per day (ore) block cave operation (DOZ Mine) and a 160,000 tonne per day (ore) open pit mining operation (Grasberg Open Pit). The Grasberg Open pit mine will be complete in 2016 at which time PTFI?s operations will convert to Underground. Mining operations will transition from today?s mixed surface and underground operation to full underground mining over the next 6 years. This paper reviews the history of Redpath?s relationship with PTFI, beginning with a raiseboring contract in 1981 and evolving into vertical and horizontal development contracts of up to 37,700 equivalent metres of lateral development and 4,000 metres of vertical development in 2011. An overview of the current operations (PTFI?s Grasberg Open Pit and DOZ Underground Mines) and transition period (challenges for the transition from current to future underground mines) is presented with details of development of common underground infrastructure and future mines; Big Gossan Mine, DMLZ Mine, Grasberg Block Cave Mine, and the Kucing Liar Mine.

Oct 1, 2010

By Botao Lin, Yan Jin, Hongjuan You, Jingjun Pan, Huiwen Pang, Mian Chen, Sen Chen

"Steam Assisted Gravity Drainage (SAGD) has become the mainstream technology for ultra-heavy oil recovery in Xinjiang oilfield, the success of which depends heavily on shortening of preheating period as well as forming homogeneous and highly permeable zone in land-facies oilsands layer. Towards this aim a special hydraulic fracturing process is required, which is accomplished through controlled water injection to a pair of horizontal wells in order to create homogenously distributed microcracks in the zone between the two wells. The associated mechanical response, however, is unclear for land-facies Karamay oilsands that is loose in texture. In this regard, this research utilizes a triaxial test system on cylindrical specimens extracted from field-collected oilsands cores. Isotropically consolidated drained triaxial compression tests are conducted on both saturated and unsaturated specimens so as to investigate the mechanical response of oilsands at different spots relative to the wellbore. Moreover, acoustic emission and fast pulse-decay permeability are performed to monitor fracture development and permeability evolution. Based on these experimental studies, the mechanism of dilation in oilsands is comprehensively analyzed. The findings reveal distinctive behavior between the saturated and unsaturated specimens as respect to dilation, porosity/volumetric evolution and change of permeability. It is also found that shear bands can be created upon shearing on triaxial specimens, rendering porosity or volumetric strain the factor that is more proper for evaluation of stimulation efficiency in the field.INTRODUCTIONXinjiang oilfield is widely known for its abundant deposit of heavy and ultra-heavy oil that has been estimated to be several hundred million tons. The ultra-heavy oil deposit located in Fengcheng region of Karamay at the northwestern part of the Junggar Basin, Xinjiang, China, has over 360 million tons of resource (Yuan et al. 2013). The resource is deposited in depths from 180 to 450 m and has viscosity over 100, 000 mPa•s at a temperature of 50ºC, bringing technical challenges to recovery activities."

Jan 1, 2015

By H. D. Stolovitch, M. L. Lavallée

"An engineering system used to analyze and improve the performance of industrial grinding circuits has been adapted into a training program. The systematic approach to the design of training was applied in order to:Determine if training was an appropriate and effective tool for the transfer of this new technology;Define the technical content of the program;Establish program specifications based on learner and context characteristics;Design and test prototypes of the instructional modules; and,Establish a strategy for plant implementation and maintenance of the training program.This paper thus describes how a engineering system is transferred to the workplace through the use of designed instruction.INTRODUCTIONTraining can change human performance in a permanent way. It can improve productivity for the overall benefit of an operation. Organizations can therefore use training as a mean to achieve their specific goals. Training is not the solution to every performance problem. However, in many cases, it can be a very effective way to attain desired performance.The benefits of training are often difficult to assess. However, to remain competitive, organizations must introduce new products and innovative technologies. Often, they can do both most effectively through suitable training interventions.In order for the effort and investment of training to provide optimal results, two points of view should be adopted.• An overall view of the system in which training is to be applied.• A systematic approach to the design of training (Stolovitch and Keeps, 1989)."

Jan 1, 1992

By Daniel Hodouin, Claude Bazin

"A graphical method to assess the size reduction by grinding is presented and illustrated with data collected from laboratory grinding tests and industrial grinding circuits. The method lies between the graphical comparison of size distributions and the population balance model. The method is easy to apply and provides a quick way to compare grinding mill performances under various operating conditions and processed ores. The application of the method to industrial mills shows that a grinding mill operation could present an invariant behaviour that can be exploited for simulation purposes.INTRODUCTIONThe size reduction of particles by grinding has been studied for decades and several books were published on the subject. Most of the recent studies focus on the modelling of the ball, semiautogenous and autogenous grinding mills operation (Napier-Munn et al., 1996) because accurate simulators can be used for design, optimization and control. Although the development of realistic simulators is progressing, the trial and error method is still used by many operators to identify optimum operating conditions for a grinding machine.Laboratory tests allow the characterization of the material submitted to grinding and the analysis of various operating conditions, such as ball size or shape, mill speed and slurry concentration of solids, on particle size reduction. Similar tests can be conducted in a plant, but results are often difficult to analyze due to errors associated with sampling and sensor accuracy. This paper presents a graphical method to assess the degree of size reduction carried out by a grinding machine. The paper consists of three sections. The first section describes the method and the following sections illustrate the method with data taken from laboratory and industrial grinding machines."

Jan 1, 2004

By W. Curlook, V. G. Papangelakis, M. Baghalha

A pressure acid leaching process has been developed for the extraction of metal values, nickel, copper, cobalt and zinc, from base metal smelter slags. The basic concept contemplates cooling the smelter slags through solidification sufficiently slowly to induce a good measure of crystallization; and subsequently, after fine grinding, to pressure leach such slags at around 250°C while applying oxygen overpressure, utilizing smelter byproduct sulphuric acid. High levels of extraction of the slags' metal values are thereby achieved. It has been shown that if the same slags are quenched thereby producing an amorphous structure, the resulting metal extractions are very low. The process is applicable to smelting furnace throwaway/discard/dump slags, as well as to in-process converter slags. By extracting the bulk of the residual base metal values in the throwaway/discard/dump slags, the resulting leached residues are rendered virtually benign vis-à-vis the external environment.

Jan 1, 2004

By J. B. Boisvert, W. Board, C. R. Mooney

"Traditional geostatistical modelling methods are difficult to apply to heavy-tailed deposits because the extreme positive skew of the grade distribution leads to bias. The focus here is on an innovative method of modelling the high-grade population by conditionally simulating discrete volumes (nuggets) of gold with marked Poisson and Cox processes. Capping and other ad-hoc manipulation of the assay data is not required; however, an intensity map for the point processes is required. The method is demonstrated on a dataset from an epithermal deposit and demonstrates an improvement in reducing smearing and controlling the skew of the grade distribution.RÉSUMÉ Les méthodes traditionnelles de modélisation géostatistique sont difficiles à appliquer dans des gisements dont la distribution de la teneur est à queue lourde car l’extrême asymétrie positive de la distribution de la teneur génère des biais. Dans le présent article, l’accent est mis sur une méthode novatrice de modélisation de la population à haute teneur par la simulation conditionnelle des volumes discrets d’or (pépites) au moyen de procédés marqués de Poisson et de Cox. La limite d’utilisation et d’autres manipulations ad hoc des données ne sont pas requises; toutefois, il faut une carte des intensités pour le processus ponctuel. La méthode est démontrée sur un ensemble de données d’essais provenant d’un gisement épithermal et elle montre une amélioration dans le lissage du flou et dans le contrôle de l’asymétrie de la distribution de la teneur."

Jan 1, 2015

By James D. Bittner

Separation Technologies, LLC (ST) has developed a processing system based on triboelectric charging and electrostatic separation that provides the mineral processing industry a means to beneficiate fine materials with an entirely dry technology. The environmentally friendly process can eliminate wet processing and required drying of the final material. The process requires little if any pre-treatment of the material other than grinding and operates at high capacity ? up to 45 tonnes per hour by a compact machine. Energy consumption is low, approximately 1 kWh/tonnes of material processed. Since the only potential emission of the process is dust, permitting is typically relatively easy. In contrast to the other available electrostatic separation processes that are typically limited to particles greater than 75 µm in size, the ST belt separator is ideally suited for separation of very fine (<1 µm) to moderately coarse (500 µm) materials with very high throughputs. The triboelectric particle charging is effective for a wide range of materials and only requires particle ? particle contact. The small gap, high electric field, counter current flow, vigorous particle-particle agitation and self-cleaning action of the belt on the electrodes are the critical features of the ST separator. The high efficiency multi-stage separation through charging / recharging and internal recycle results in far superior separations and is effective on fine materials that cannot be separated at all by the conventional electrostatic techniques. Since 1995, this triboelectric process has been extensively used for the beneficiation of coal fly ash with eighteen separators in place and over 100 machine-years of operation at locations in the US and Europe. The technology has been also successfully applied to the beneficiation of a variety of minerals including calcium carbonates, talc, and potash.

Nov 1, 2011

By Scott Hopkins

Simulation tools are preferred for evaluating complex systems due to its ability to mimic reality and quickly evaluate many different what-if scenarios and find global solutions. A simulation model is capable of representing variable and dynamic disturbances that are typically encountered in day-to-day operations; this is where spreadsheet models or linear programs fall short because they cannot account for the dynamic behavior and relationships. The simulation model used for this work was developed by Xstrata-Nickel (previously Falconbridge). The simulation tool is very flexible and can be used to simulate different mining and development methods. The scope of the modeling included production mining, geology, equipment fleets, equipment maintenance and random failures, manpower, shift schedules, and cycle activity times. A case overview of the 170 Orebody will be presented along with the challenges associated with data collection for the model inputs. Results and lessons learned will also be discussed.

May 1, 2008

By C. L. Reichardt

"Pressure exerted on gold producers by regulators, project financiers, and civil society in the wake of the Baia Mare tailings spill in Romania during 2000 prompted most responsible gold companies to sign up to the International Cyanide Management Code for the Manufacture, Transport, and Use of Cyanide in the Production of Gold (the Code). The Code stipulates a ‘cradle to grave’ approach more comprehensive than that applied to any other mining reagent and poses particular challenges for operators who use cyanide-bearing tailings for backfill. This paper examine some of the challenges for Code compliance facing deep underground gold mines that employ backfill technology, most particularly the requirement to demonstrate that the potential migration of cyanide (and its degradation products) from emplaced backfill will not have an unacceptable impact on worker health and safety or on the receiving environment, either during mine life or after closure.Although the Code only contains a single reference to backfill, more careful consideration confirms that most sections of the Code that deal with tailings management are potentially applicable to mines where tailings material is used for backfill. Certain principles of the Code also pertain to aspects of operations, worker safety, emergency response, training, and dialogue with stakeholders relating to backfilling practice.For gold mines of the Far West Rand, the most significant cyanide-related risks associated with backfill operations relate to worker exposure to cyanide-bearing seepage and HCN gas. There is potential for seepage of cyanide-bearing water from backfill to compromise the beneficial use of surface and groundwater, and thus impact on downstream users and ecosystems. However, the extreme depth of mining and the specific geological and hydrological controls on the Far West Rand suggest that the potential environmental risks associated with backfill are likely to be considerably less significant than the cyanide-related risks to the workforce."

Jan 1, 2007

By Patrick F. R. Murphy

The mechanization of platinum group metal (PGM) underground reef mining in South Africa has posed a challenge to mining engineers for several decades. This is primarily due to the shallow dip angles and narrow thickness (<1.1m) of the tabular orebodies mined, and the issues faced in developing reliable drilling, bolting and loading machines suitable for such hard-rock mining applications. Presently, mining is typically conducted using hand drills and scraper shovels. These methods, however, are intensive in terms of manual labor, and limited in terms of productivity, and improved methods are desired. This paper will review the technical features of a 4 tonne, low-profile, LHD for narrow-reef PGM mining, developed by EJC Loaders Division.

May 1, 2003

By J. A. McLennan

Geological uncertainty is an unavoidable characteristic of all mining projects since only limited information is available from sampling. Mine planning and development decisions with significant economic consequences are made when the geological heterogeneity is inherently uncertain. Geostatistical simulation is preferred over kriging because the methodology provides alternative property realizations that can be combined into a model of geological uncertainty. Geological uncertainty can be transferred into production uncertainty, which can help characterize the economic risk of the project. This paper presents a case study for the Pogo property, being prepared for development near Fairbanks, Alaska. The exact dimensions, grades and production predictions have been modified; however, the methodology is illustrative. The geostatistical methodology consists of (1) assembling the relevant drillhole data and establishing a suitable coordinate system, (2) calculating the target distribution, (3) creating a model of spatial correlation, (4) generating multiple realizations at a small scale and (5) linearly averaging all the realizations to the chosen selective mining unit (SMU) support size. The geostatistical model is then used to calculate production uncertainty.

May 1, 2004

By Brad E. Melanson

Because mine haul trucks consume considerable quantities of fuel, they are ideal candidates for the adoption of cleaner and cheaper fuels like natural gas. Impressive fuel cost savings will be realized in regions where liquefied natural gas (LNG) has cost advantage to diesel fuel, while also providing significant reductions of air contaminants and greenhouse gases. High Pressure Direct Injection (HPDI) of natural gas utilizes the diesel cycle combustion process and therefore retains the diesel engine?s high performance and efficiency characteristics. HPDI has been demonstrated in on-road Class 8 trucks since 2001 accumulating almost 10 million kilometres to date. The supply of LNG fuel will be an essential parallel aspect in the introduction of HPDI to mining. LNG can be transported to site as diesel is today, or may be produced on or near mine operations that have access to methane sources or pipelines.

May 1, 2006