Search Documents

By P. O. Sandstrom

"Atlas Copco is introducing a new patented method for full-face boring. This paper presents the basic principles of the boring action and discusses the present experience regarding performance and costs. The Atlas Copco ""Full-facers"" are designed for hard-rock applications, although they are successfully boring in soft ground without major changes. The unique patented boring principle referred to as the 'Undercutting Method' permits these machines to bore, economically, in harder ground than machines based on the 'crushing principle'. This is mainly due to considerably lower cutting-tool costs, as the tungsten carbide tips only are in contact with one-third of the bored volume. The remaining rock is 'undercut' and peels off from a slight back pressure.The undercutting method also permits boring of non-circular headings and Atlas Copco has already manufactured two machines for rectangular drifts. This concept could revolutionize development work in mines employing trackless equipment."

Jan 1, 1971

By R. E. Eyre

ALTHOUGH the idea of roasting zinc concentrates in suspension had intrigued investigators for a number of years, no commercial application of a process appeared successful until the development of the "Cominco" process. The efficiency and high capacity of this process may be judged by the fact that nearly all other electrolytic plants and many zinc retort plants in the world use this method. A furnace of the Cominco type can roast without special preparatory treatment and without supplementary fuel, mineral sulphides such as zinc sulphides and iron sulphides containing varying amounts of moisture at any desired rate ranging from one-half up to full capacity. The full capacity of a unit is in general about three times that of a multiple hearth furnace of the same size. The latest type of "Cominco" furnace can be built for capacities from 25 to 500 tons per day. The quality of the calcine is subject to positive control and may be

Jan 1, 1961

By Marc Ruest

A new instrumented cable bolt has been developed by the National Institute for Occupational Safety and Health at the Spokane Research Laboratory in Spokane, WA. Although various instruments are available to measure load distribution and magnitude along a grouted cable, this instrument is innovative in that it uses strain gauges internal to the cable as load-measuring sensors. The instrument has been successfully tested in the field at FMC?s Granger Mine, Meikle Mine, and Getchell Mine. A ?split-pipe? laboratory pull test was performed on each of three cable bolts instrumented with the new device. Each test consisted of grouting a 1.83-m-long cable in two 0.91-m-long sections of schedule 80 pipe. A numerical analysis was then performed in which laboratory boundary conditions were simulated and model properties derived from textbook guidelines. The loads calculated by the model were then compared to the measured loads.

May 1, 2002

By Fred C. Delabbio

The successful implementation of a new technology in an underground production mine requires many challenges to be overcome. These challenges include mine hardening of new technology, mitigation of safety risks and hazards, mine operation support, and technology transfer to mine staff. In the end, the majority of these challenges relate to the human aspects of implementation. The approach selected to overcome these challenges must be customized and appropriate for each unique situation. This paper outlines the approach used to address these challenges as part of successful implementation and resulting demonstration of the hydrogen fuel cell locomotive at the Placer Dome (CLA) Limited, Campbell Mine. This technology demonstration at Campbell Mine is critical for determining technical, regulatory and implementation aspects to be incorporated into future fuel cell prototypes such as the LHD project.

May 1, 2003

By Patrick Polk

For many years, sulfuric acid producers all over the world have been forced to meet ever more strict environmental regulations to reduce SO2 emissions. The sulfuric acid industry has implemented new solutions in order to comply with the new lower SO2 emissions target. Haldor Topsoe (Topsoe) has responded to this challenge by continuously improving the range of VK sulfuric acid catalysts and providing tailor-made catalyst solutions to meet the demands of the sulfuric acid producers for lower SO2 emissions. Reducing emissions through catalysis: requires less capital than installing a scrubber, requires no additional process chemicals, generates no waste or by-product to dispose of. In 1996 Topsoe introduced VK69, a cesium-promoted vanadium catalyst, designed for operation in the pass(es) after the intermediate absorption tower in double absorption plants. The high activity of VK69 allows for a more than 50% reduction in SO2 emissions from existing double-absorption plants. Topsoe currently has more than 110 installations of VK69. To comply with the still more stringent regulations being placed on the sulfuric acid industry to lower SO2 emissions, Topsoe has developed a new sulfuric acid catalyst designated VK-701 LEAP5™. This catalyst was introduced to the market in 2010. VK-701 LEAP5™ is based on a novel technology which circumvents the internal transport deficiencies of existing commercial sulfuric acid catalysts and thereby offers exceptionally high activity in strong, SO3 rich gases. Sulfuric acid plants have used this catalyst to meet emissions requirements lower than previously believed possible with a catalyst only solution. This paper will present examples on how to reduce emissions by implementing a tailor-made catalyst solution using VK69 and VK-701 LEAP5™.

Jan 1, 2014

By Maryam Sadeghi, Jonathan Roy, Claude Bazin

"The operation of mineral processing equipments is intimately related to the mineral composition of the ore. However unit performances are usually characterized in terms of metal contents or recoveries as this data is easier to obtain than the mineral contents. This paper describes a method that combines the operations of material balancing and estimation of the mineral contents of the ore. The estimated mineral contents can be used for process analysis and diagnosis of operating problems.IntroductionThe ore that is feeding a concentrator is made of minerals that condition the energy requirements for the ore comminution and the performances of the subsequent separation circuit. Indeed a change in the mineral composition of the ore may lead to lower grinding mill throughput as well as lower recovery or grade of the economical products. Despite this relationship is recognized the mineral composition of the ore is seldom measured or estimated to provide regular information for the diagnosis of operating problems. Some methods such as the QEM-SCAN (Whiten, 2008; Lamberg and Vianna, 2006) are available to measure the concentration of the minerals in ore samples but the method is time demanding and plant operators usually base their evaluation of the plant performances on chemical assays of metals or elements since this data is easier to obtain from ore samples.Usually samples of the streams of mineral processing plants are collected on a daily basis to be assayed for strategic elements. The obtained concentrations are balanced to produce coherent data with the material conservation constraint and then used to characterize the day to day operation of the plant in terms of recovery of valuable metals and grades of the marketable concentrates. The behavior of contaminant elements can also be monitored from this data allowing the operators to explain for instance a lower zinc concentrate grade by a more important contamination of iron. However such diagnosis is only partial as the contaminant element can be transported by different minerals. Indeed the iron contamination of a zinc sulfide concentrate may be caused by an inadequate depression of pyrite or due to another iron carrying mineral. A possible way to answer the question is to determine the concentrations of the various minerals in the ore and produced sealable concentrates. Since measuring the mineral contents of the ore could be a demanding task one should consider to estimate this data from the daily chemical assays of the sample collected on the main streams of the circuit. Some authors have already investigated the problem. Whiten(2008) described a method to estimate the mineral contents of an ore sample. Lamberg and Vianna(2006) proposed a method to do a sequential mineral reconstruction followed by a material balance. Few of these methods account for the mass conservation of the reconstructed mineral contents."

Jan 1, 2016

By A. C. Wilson

"In 1991, local prospector C. “Mickey” Clement recovered at least three alluvial diamonds from the Michipicoten River. Two of these stones were sent to the Department of Mineralogy, Royal Ontario Museum, where they were identified as industrial-grade diamonds with weights of 1.05 and 1.13 carats. Both stones were described as frosted and graphiteinclusion riddled.In 1995, prospector Sandor Surmacz and geologist Marcelle Hauseux discovered diamonds in bedrock approximately 20 km north of the Michipicoten River. An 18.1 kg bulk sample of a xenolith-rich lamprophyre, taken from an outcrop at the side of the Trans Canada Highway north of Wawa, yielded 1 macro diamond and 5 micro diamonds. All but one was gem quality (Sage, 2000).Since then, more than 36 occurrences of diamonds in bedrock have been reported in an area approximately 30 km2 in size, centred 20 km north of the town of Wawa. The occurrences are hosted within a sequence of unusual, Archean-aged, heterolithic breccias previously considered to have no economic significance. Ten kimberlite occurrences also have been confirmed in the Michipicoten greenstone belt in the last five years. Two of these kimberlites are diamondiferous.To date, expenditures on property acquisition and diamond exploration in the Wawa are estimated at CDN$120 M.This paper summarizes the geological observations made on these occurrences and describes the relationship between the occurrences and the regional geology."

Jan 1, 2004

By D. M. Doyle, P. J. Hannon

"The Canada/Nova Scotia Mineral Development Agreement (M.D.A.) is a subsidiary of a five-year Economic and Regional Development Agreement, signed on June 11, 1984. The objectives of the M.D.A. are to strengthen and diversify the Nova Scotian mineral industry and to coordinate federal and provincial policies and programs. The agreement outlines the activities and responsibilities of each government, including the division of the cost (60:40, federal: provincial) between governments. The agreement established a framework for joint planning to avoid overlap or duplication of programs.The M.D.A. programs are broadly divided into five sectors (Table 1 and Fig. 1): Geoscience, Minerals Technology, Development, Firm Specific and Public Information. Each sector is administered by a subcommittee composed of one federal member and one provincial member. The subcommittees report to a Management Committee. The Canada/Nova Scotia Mineral Development Agreement (M.D.A.) Management Committee is made up of Dr. Jack Reeves from EMR and Dr. Richard Potter from the NSDME.The Geoscience subcommittee, co-chaired by Peter Giles (NSDME) and William Poole (EMR), manages the regional geologic, geochemical and geophysical studies in the province. Included in this sector are studies into mineral deposits and the basic geological relationships between mineral deposits.The Mineral Technology sector is co-chaired by the authors, Don Doyle (CANMET) and Pat Hannon (NSDME). This sector of the M.D.A. conducts studies into mineral processing, sampling, deposit byproduct commodities and project feasibility analysis."

Jan 1, 1987

By R. Sharon, P. M. Hawley, X. Ochoa

"Development of Barrick Gold’s Pierina gold mine in north-central Peru requires construction of a waste dump for disposal of nonore grade materials stripped from the open pit to expose the ore. The waste dump site is located near the open pit in a U-shaped valley that is underlain by thin colluvial and morainal soils with locally thick peats and glaciolacustrine deposits. Bedrock underlying the site consists of variably weathered volcanics. The site is subject to moderately high seasonal rainfall and significant seismicity. The geotechnical quality of the waste rock is highly variable, ranging from low-quality, degradable, soil-like materials containing appreciable quantities of silt and clay, to high-quality, hard, durable, blocky waste rock.A hybrid dump design concept was developed that requires in-pit segregation of highand low-quality waste, and selective placement of materials in the dump to maximize stability and enhance internal and subsurface drainage. The design includes a rock drain beneath the dump along the axis of the valley and a series of connected finger drains. Extensive peripheral diversions and stormwater control measures to inhibit infiltration of precipitation are also included.This paper discusses the unique challenges presented by the site and waste materials, the design methodology and stability analyses, and planned monitoring systems."

Jan 1, 2003

By Peter Waggitt

Northern Australia has been home to uranium mining for over 70 years, more or less continuously. In the early days, post World War 2, there was little effort made to remediate workings at the end of operations. The three “campaigns” of uranium mining (1951-55; 1960-70; and 1979-present) are all now in various stages of remediation. This includes not only the large legacy site at Rum Jungle but also smaller fields like the South Alligator Valley, as well as contemporary works at Nabarlek and the ongoing closure at Ranger– Australia’s longest operating uranium mine. This paper briefly describes some of the past remediation activities before providing an update on the Ranger closure programme and future timetable.

Jan 1, 2020

By Michael Cooper, Eric Konigsmann, A. Moerman

"A paste backfill plant and underground piping distribution system was commissioned at the Brunswick Mine in June, 1998. Concentrator tailings, composed mainly of pyrite and lesser amounts of silicate minerals with a P80 of 37um (45 YO-20 pm), are pumped to the backfill plant. The backfill plant uses conventional thickening and disc filtering to dewater the solids, which are then mixed with binder in twin screw mixers. The paste is discharged through a gob hopper and one of three boreholes by gravity. Approximately 65% of the concentrator tailings will be placed underground at full production. The remaining thickened tailings will be pumped to an existing impoundment area. Application of paste technology will completely replace the use of cemented rock fill in the mine by the end of 1998.The design capacity of the paste backfill plant is a total of 360 dmtph of cemented paste through two parallel production lines. The plant is highly instrumented and controlled via a hybrid Programmable Logic Controller (PLC-5) and Fisher ProVox Distributed Control System that is in communication with the property information highway. Video and audio signals from the underground system are carried to the surface plant via a leaky feeder communications/fiber optic system.The underground distribution system consists of a network of 200mm diameter boreholes and piping. There are approximately 3.5km of boreholes and 5.5km of piping in the system. To minimize pressures, the greatest piping length from any borehole is approximately 400m with all piping being open-ended. There are no valves in the entire paste distribution system.Construction of the plant, including installation of piping to and from the plant and preparation of the underground distribution system, was completed in less than one year from the time of management approval for the $M 22.3 project."

Jan 1, 1999

By Rob Sloan, Simon Yu, Rob Robison, Mark Schmidt

"In 2000-2009, Highland Valley Copper (HVC) tested new generation 660 mm cyclones supplied by various manufacturers in an aim to replace existing first generation 762 mm cyclones without success. Due to plant infrastructure limitations, new generation larger (838 and 800 mm) cyclones were not feasible. In 2010, an approach of testing hybrid 800 mm diameter cyclones was initiated by HVC. The hybrid cyclone consists of an 800 mm cyclone upper head section and the use of existing 762 mm cyclone conical sections. Three hybrid 800 mm cyclones were engineered and fabricated, targeting a throughput of 850-950 mtph and were installed in the E line cyclone cluster. Since starting operation on September 20, 2011, three hybrid 800 mm cyclones have been running at combined throughput ranges of 750 to 1050 mtph. Based on plant Daily Met Reports, the test hybrid cyclones demonstrated a decrease in misplacement of coarse copper bearing material to the cyclone overflow and better cyclone efficiency when compared to the existing 762 mm cyclones at the same throughput. The hybrid 800 mm cyclones also demonstrated significantly higher capacity per unit when compared to the existing cyclones. Based on the improvement demonstrated in the full plant trials, HVC decided to install the new hybrid 800 mm cyclones in all five grinding lines starting in July, 2012. A more detailed discussion of the full plant trials and initial results of the first complete retrofit of E line will be presented. INTRODUCTIONHighland Valley Copper Partnership (HVC) is Canada’s largest base metals mine and one of the world’s largest producers of Cu-in-concentrate. The mine, located in the central interior of British Columbia, is owned (97.5% interest) and operated by Teck Resources Ltd. In 2011, HVC produced about 210 million lbs. of Cu and 8 million lbs. of Mo. HVC’s Mill Modernization Project (MOP), which was budgeted for $475 M, is currently under intensive construction and is scheduled for commissioning in Q1 2014. The following description was valid at the time of writing this paper.The operation has been expanded a number of times since the startup of the original Lornex mill in 1972. The plant started up with two 9.75 m (32 foot) diameter primary SAG mills. It was expanded in 1981 with the addition of a 10.36 m (34 foot) diameter SAG mill. In 1988, the Highmont concentrator grinding mills and flotation section were moved and attached to the Lornex mill site. This added two10.36 m (34 foot) diameter AG primary mills to the Highland mill. This brought the total number of primary mills to five referred to as Line A, B, C, D and E: three SAG mills (A, B and C) each with two ball mills in parallel and two AG mills (D and E) each with one ball mill. Each AG mill line is equipped with one short head pebble crusher. Ball mill circuits are classified using 8 clusters of ten Linatex 762 mm cyclones to reach a target P80 330 micron (equivalent 43% +100 mesh), before the cyclone overflow product advances to the bulk flotation circuit."

Jan 1, 2013

"The Dumont deposit is a large (1066 Mt probable reserve) low grade (0.27% nickel), nickel sulphide project located in the Abitibi region 25km west of Amos, Quebec. Royal Nickel Corporation acquired the project in 2007 and has since taken the deposit through pre-feasibility. And updated, revised pre-feasibility was released in July 2012.The disseminated nickel sulphide and alloy mineralization is hosted within the serpentinized dunite subzone of the Dumont Sill; a differentiated, pervasively serpentinized, ultramafic sill of komatitic affinity. Pentlandite, heazlewoodite and awaruite are the dominant nickel-bearing, metallic phases and can be recovered by conventional methods (flotation, mag separation). Non-recoverable nickel is also present within the silicate matrix of the serpentinized dunite and is locked in serpentine (Fe and Mg-rich variants) and minor olivine.A detailed mineralogical program including 1097 QEMSCAN® samples and 4300 electron microprobe points were undertaken to increase the understanding of the nickel deportment in the various recoverable and non-recoverable phases in a spatial context across the deposit. Eighty-three (83) metallurgical tests performed under a standard procedure have linked the mineralogy to metallurgical performance. This has allowed the creation and modelling of geometallurgical domains on a block by block basis to understand the recovery variation and metallurgical performance throughout the deposit. Understanding the spatial variability of Ni deportment in recoverable and non-recoverable phases through mineralogy is the key to understanding metallurgical performance thus, unlocking the value of the Dumont deposit and other large tonnage low grade ultramafic nickel deposits."

Jan 1, 2013

By Poul Hansen

"In mid-I986, a world-class mining enterprise was created in British Columbia, bringing together the copper mining operations of Lornex Mining Corporation and Cominco into a new entity, Highland Valley Copper. This paper will focus on the background and rationalef or the formation of this partnership, the resulting operating changes and the productivity and cost benefits expected.IntroductionSince the deterioration of the world copper industry in 1981, the future of the Lomex and Cominco mines in the Highland Valley of British Columbia looked increasingly precarious. Despite the expansion of the Lomex mill complex in 1981 to one of the world's most cost-efficient copper and molybdenum concentrators, persistent low metal prices had made the remainder of the ore in the Lomex orebody marginally economic and had significantly foreshortened the expected life of the operation.Cominco had acquired the Bethlehem Copper assets in order to consolidate its ownership of the Valley orebody, and was feeding the Bethlehem concentrator with ore from the Valley orebody. In spite of the high grade and free-milling character of the Valley ore, profitability of the Cominco operation was severely restricted because of the limited capacity of the Bethlehem concentrator and its location high on the hillside above the orebody."

Jan 1, 1987

By Brian Reid

"This paper studies the progress made by hydraulic shovel manufacturers over the last few years, particularly in the areas of productivity increase and operating cost reductions.Five years ago, it was widely considered that the unit production cost for a hydraulic shovel in a mining application was double that of a cable shovel in the same application. The hydraulic machine manufacturers have taken up this challenge, and modern improvements in design, coupled with changes in maintenance techniques, have narrowed the gap to the point where it is valid to ask the question ""will the cable shovel exist in ten years' time?"".Historical BackgroundThe history of the cable shovel goes back to the early 19th century and the industrial revolution. Early machines were steam-powered and ran on rails.The ""power shovel"" and the ""dragline"" were the only mechanical means of mass excavation until the early 1950s. Rail-mounted units gave way to crawlers, which increased flexibility considerably. Some shovels were redesigned as backhoes, and some became extremely large when designed as stripping shovels primarily used in North American coal mines.In the early 1950s growth in hydraulic technology spawned the introduction of the hydraulic excavator, which soon began to replace the smaller cable shovels and backhoes used in the construction industry. They were completely self-contained with either a gasoline or diesel engine and, being much lighter, were more readily transportable.As the excavators grew in size from its early models of 0.5 m3 or less, many of the cable shovel models were discontinued. This was not surprising for several reasons, but the most obvious is that both were often made by the same manufacturer."

Jan 1, 1988

By K. Nasrallah

"The Dumont deposit is a large (1,179 Mt proven and probable reserve) low grade (0.27% nickel), nickel sulphide project located in the Abitibi region 25km west of Amos, Quebec. Royal Nickel Corporation acquired the project in 2007 and has since taken the project from a scoping study in 2010 through to completing the feasibility study in July 2013.The Dumont deposit in a nickel deposit with the recoverable nickel contained in three minerals; pentlandite, haezlewoodite and awaruite. The minerals are recovered by a combination of flotation and magnetic separation. Over the course of the studies many flowsheet design decisions and changes were made. This paper outlines an overview of the project, flowsheet design including the comminution circuit, desliming and awaruite recovery. The overall resulting flowsheet that was used for the feasibility study is then presented along with the confirmatory locked cycle testing that showed the feasibility design basis was able to produce the predicted concentrate grade and recovery.IntroductionRoyal Nickel Corporation (RNC) is a mineral resource company headquartered in Toronto, Canada, primarily focused on the exploration, evaluation, development and acquisition of base metal and platinum group metal properties. RNC's principal asset is the Dumont Nickel project (Dumont project) located in the established Abitibi mining camp, 25 km northwest of Amos, Quebec. RNC acquired a 100% interest in the Dumont property in 2007. The mineral claims covering the Dumont deposit are currently held 98% by RNC and 2% by Ressources Québec.The Dumont project is located in the province of Quebec in the municipalities of Launay and Trécesson approximately 25 km by road northwest of the city of Amos, 60 km northeast of the industrial and mining city of Rouyn-Noranda and 70 km northwest of the city of Val d’Or."

Jan 1, 2016

By S. Nikolic, G. M. Stieper, D. P. Mallah, B. J. Hogg, P. B. Voigt

Copper feed materials processing is becoming more challenging, due to an incremental increase in the mineralogical and compositional complexity of these feeds. These complex and polymetallic feeds are now becoming more common and many sites have been forced to re-evaluate their operating strategies to process these materials at cost competitive rates, whilst meeting ever more stringent environmental regulations. Most operations must first evaluate the merits of pyrometallurgical and hydrometallurgical treatment routes. Although there are multiple copper smelting technologies available, only top-submerged lance (TSL) technology, supplied by Glencore Technology as ISASMELT™, has been applied in the real world to consistently and successfully smelt complex materials in integrated metallurgical facilities such as Glencore’s Kazzinc Ltd. operation in Kazakhstan, Umicore Precious Metals Refining in Belgium and Aurubis AG in Germany. Glencore Technology also offers hydrometallurgical processing, through the Albion Process™ technology, opening up viable flowsheet options previously not possible for these complex feeds. This paper describes a number of real world process flowsheets at global operations and Glencore’s own operations at Mount Isa and Kazzinc Ltd., which process complex feeds. These flowsheets integrate the ISASMELT™, Albion Process™, ISACONVERT™, ISAKIDD™ Tank house, and bottom blown oxygen cupel (BBOC™) technologies to provide an effective process solution for the treatment of complex polymetallic feeds to produce metallic copper and associated by-products. INTRODUCTION Traditional smelters and those built in recent times within the bulk smelting hubs of the world have been designed to treat standard/clean concentrates. In recent years the processing of complex polymetallic sulfide concentrates and the recycling of secondary copper and derivatives of waste electrical and electronic equipment, such as e-scrap, have become a focus for numerous companies (Alvear & Nikolic, 2013). Processing of these complex feeds, characterized by relatively high levels of minor elements (over 5% of elements such as arsenic, antimony, bismuth, lead and zinc) is more challenging. Facilities not designed for these types of materials may require significant modifications or a change in smelting technology to treat them. Often operations find themselves re-evaluating the merits of pyrometallurgical and hydrometallurgical treatment routes for their sites through a number of factors:

Jan 1, 2019

By David Clarry

?The issue ?reduction requirement ?Planning abatement steps ?Energy Management & Energy Efficiency ?Energy Recovery / Utilization ?Alternative Energy Professional Services Overview ?Capital Projects and Construction ?Project Development and Planning ?Engineering ?Project management ?Construction management ?Consulting ?Process ?Business ?Environmental ?Technology ?Operational Services ?In-house engineering services for operations

May 1, 2009

By J. B. Scott

"A computerized cost estimating program developed with the use of the Lotus 1-2-3 spreadsheet program has produced dramatic savings in preparing estimates for operating costs, equipment fleet size and manpower requirements for underground mines.The program is used by Dynatec to support its consulting engineering projects, particularly feasibility studies. The 'first principles' approach is used to prepare detailed estimates under direct labour and supplies categories and maintenance costs for each mining operation . User notes have been developed to guide the estimator and ensure appropriate consideration is given to the specifics of the particular mine.A typical case history is illustrated and the ease by which alternatives and sensitivity analyses can be prepared is demonstrated. IntroductionHistorical MethodsMining engineers have used one or a combination of methods to prepare operating cost estimates for new or existing mine s. Operating companies have access to historical cost data and generally use this for preparing estimates. Consulting engineers do not usually have direct access to such information and must rely on mining companies (the present or previous clients); publications (text books, equipment manufacturers manuals, CMJ reference manual, etc.); annual reports (applicable to public companies); previous studies (to be used with caution as conditions change from mine to mine); and first principles (the subject of this paper), for cost information:Definition of First PrinciplesA first principles approach to cost estimating considers individual primary work elements of an operation. Quantities of work items are developed from the mine plans, production rates, geographic and physical layouts etc. The knowledgeable estimator, assisted by experienced operations personnel, can assign appropriate resources (equipment, labour, supplies and services) to each work element and establish productivities. Completion of the cost estimate is then largely arithmetic."

Jan 1, 1988

By S. Uddin

Microsegregation manifests its effect on microstructural evolution of cast or welded alloys which in turn influences their important mechanical and electro-chemical properties. In the above context, mathematical models of microsegregation have proven to play an important role in estimating the nature and predicting the effects of this phenomenon in wide varieties of solidification processes. Microsegregation models are useful in designing new commercial alloys, in estimating the homogenization time for the post-process heat treatments and in many other practical applications. In this study, two semi-analytical models of microsegregation were developed to predict the concentration field of solute in the liquid and solid regions for dendritic solidification of binary metallic alloys. Both models assume that the growing dendrites are cylindrical in shape. This assumption is more realistic compared to the common assumptions of plate like dendrites that most of the earlier researchers employed in their microsegregation modeling study. The solute redistribution profile, in the developing solid layer, necessary to determine the back diffusion parameter was derived from Fick's second law for the model without coarsening. The application of this parameter in a wide range of conditions and the use of its basic form in the model with coarsening has been verified. The concept of coordinate transformation and enhancement of back-diffusion Fourier number were used in deriving the model which took into account the coarsening of dendrites. The models are then extended to deal with rapid solidification and peritectic transformations and the results were compared with relevant experimental data for Aluminum and other alloys. A good agreement between model predictions and experimental results was found.

Jan 1, 2007