Search Documents

By Pollard D. M

The removal of nickel from lead by sulfur drossing was investigated using a technique which models industrial batch decoppering practice. Successful denickeling to 0.005% (Ni)pb was consistently obtained in the absence of silver, well below the experimental equilibrium value of 0.015% but still above levels obtained in industrial practice. Silver appeared to have little effect upon denickeling. The final nickel content was dependent upon the initial nickel content, the total sulfur addition and the stirring time. The presence of nickel was found to give no assistance to successful decoppering. Simul- taneous removal of nickel and copper was observed at silver contents in excess of 0.02%. Extended stirring resulted in a further lowering of the nickel content but reversion of copper to the bullion was observed. Experimental work has shown that nickel can be removed by a standard decoppering operation; a procedure which is used in secondary lead re- fining. Alternatively nickel can be removed during initial decoppering in primary lead re- fining operations.

Jan 1, 1987

By Minglin W, Zhixing L

The laws of detonation wave velocity variation in propagation process along the charge under channel influence are investigated widely in this paper. The result is obtained by blasting experiments. Bore hole is simulated by plastic tube or steel pipe (with outer diameter 45 nun, inner diameter 40 or 41 mm). Blasting experiment is carried out with a cylindrical charge of 32 mm diameter. The author analyses the characteristics of energy distribution along the charge under above-mentioned conditions. Reasonable initiating position and initiating direction are also analysed. A double-direction initiating method which consists of several initiating charges is put forward. The blasting effect of this initiating method when used in underground mining is stated out.

Jan 1, 1990

In the last few years a number of mineral laboratories were established in Indonesia coinciding with the increase in gold exploration in the region. Prior to this, much of the analytical work was sent outside the country,however this is no longer neccessary.

Jan 1, 1990

During mapping in the Bijerkerno area (Fig. 1), well-preserved sedimentary structures were found at three separate localities. The structures are of four varieties, which are 1. small-scale cross-bedding (Fig. 2),2. convolute bedding (Fig. 3),3. minor scour and fill (Fig. 4), and4. flame structures.Ripple-marking is also doubtfully present.These structures are best preserved in what was...

Jan 1, 1971

By Callcott R

Prediction of raw coal size distributions and those generated by processing are examined using spreadsheets and the matrix analysis of breakage processes. Run of mine coal size distributions are predicted from the lithotype properties using a

Jan 1, 1998

By Happ J. V

Factors affecting the rate of arsenic removal from lead bullion during softening processes were studied. Very high rates of removal could be obtained under conditions of intense agitation and ready availability of oxidant. Reaction mechanisms were proposed to explain the sequences observed. Selective removal of arsenic with minimal loss of antimony from bullion was favoured by a low temperature Harris process and oxidizing via a caustic soda medium.

Jan 1, 1987

An approach to underground mining of shallow dipping, thick seam coal is proposed in broad outline. The method is based upon overhand slice and fill, with hydraulically emplaced washery refuse as the filling material. Likely fill behaviour and character- istics are discussed and likely problem/investigational/ research areas defined.

Jan 1, 1976

By A V. Nguyen

Spherical calcium dioleate particles (~10 ¦m in diameter) were used as AFM (atomic force microscope) probes to measure interaction forces of the collector colloid with calcite and fluorite surfaces. The attractive AFM force between the calcium dioleate sphere and the fluorite surface is strong and has longer range than DLVO (Derjaguin-Landau-Verwey-Overbeek) prediction. The repulsive AFM force between the calcium dioleate sphere and the fluorite surface does not agree with the DLVO prediction. Consideration of non-DLVO forces, including the attractive hydrophobic force and the repulsive hydration force, was necessary to explain the experimental results. The non-DLVO interactions considered were justified by the different interfacial water structures at fluorite- and calcite-water interfaces as revealed by the numerical computation experiments using molecular dynamics simulation.

Jan 1, 2005

The facilities used and techniques employed in the manufacture of steel and iron rolls at the Steel Foundry, B.H.P., Iron & Steel Works, Newcastle are described.

Jan 1, 1972

By Booth GW, Robertson IG

The Paddington Gold Mine ties within the Norseman-Wiluna greenstone belt, in the celebrated Eastern Goldfields province of the Yilgarn Block, Western Australia. Regionally, tropical to subtropical weathering has effected development of a prominent regolith and a deep lateritic profile. Detailed examination of the clay mineralogy, largely from a single drill hole which traversed the original Paddington I deposit, outlined three separate, vertically gradational assemblages, which are, in part, rock-type dependant. These include; 1. kaolinite with minur to trace quantities of sericite/illite (0-22m), 2. smectite and/or interstratified clay minerals, together with variable amounts of kaolinite, relic chlorite and illite/sericite (22-81m), and 3. chlorite and sericite (> 81m). Near surface, kaolinitic assemblages may be directly correlated with the intensity of lateritization, whereas smectite and interstratified clays from intermediate zones appear in association

Jan 1, 1989

By T Ueda an, T Sasaoka, A Yabuki, H Shimada

The basic concept of auger mining is to extract coal beyond the economic limits of surface mining technology by drilling holes of an appropriate diameter size into the exposed seam of the highwall as deep as is technically, economically and operationally feasible. This method of mining is used at the final highwall of typical surface mining operations. This paper describes the auger mining systems and discusses the methods to increase the coal recovery in auger mining from a field trial in Australia.

Jan 1, 2003

By Noreen D

At Bougainville Copper Limited comparison testwork was conducted between "horizontal" cycloning and conventional vertical cycloning. Horizontal cycloning reduces circulating load and allows increased ball mill throughput. Cyclone efficiency is the same or better as a result of the reduction of fines short-circuiting to the underflow. Operationally, horizontal cyclones are less likely to suffer from blocked spigots and high cyclone feed pump sump levels. Cyclone feed pumping power is reduced. High horizontal cyclone underflow density provides the option to optimise grind by manipulating water addition to the ball mill feed.

Jan 1, 1988

By Kerkhoff G, Wood J

The maximum gas emission into underground workings can be predicted by the use of established methods which have world wide recognition. Changes in gas emission and the influence of the gas and geological environments during longwall mining at Pacific Colliery, were found.to be a typical. The relationship between longwall mining and gassy conditions is found to vary from the European experience because of the different mining and geological conditions encountered, and the higher productivity achieved, by single longwall panels in Australia.

Jan 1, 1988

This paper describes the oil engihe plant owned and operated by Gold Mines .of Kalgoorlie Limited, and gives some details of installation, operational, and maintenance experiences which have arisen during the years of service, the last 5 years of which have been under the writer's control. Nos. 1, 2, 3 and 4 alternator units have run 50,276, 48,006, 49,677 and 25,930 hours respectively, and much knowledge has been obtained of their performances and faults. During the war years, it has not been easy to obtain spare parts; this, coupled with the loss of No. 4: alternator unit to the Commonwealth Government, made operation and maintenance a very difficult problem.All engines are of the enclosed vertical, single acting, 4-stroke cycle, airless injection type.The electrical power plant originally consisted of four 6-cylinder Belliss & Morcom heavy oil engines, direct coupled to Bruce Peebles alternators, running at 375 r.p.m., and generating 3-phase electric power at 3,300 volts, 50 cycles.No. 1 unit, installed in 1936, is a 6-cylinder 450 b.h.p. standard 12A Belliss & Morcom heavy oil engine, direct coupled to 280 kw. 0.8 p.f. alternator. The remaining three units are 6-cylinder, 660 b.h.p., lSA oil cooled piston type Belliss & Morcom heavy oil engines, direct coupled to 410 kw. 0.8 p.f. alternators, making a total capacity of 1,510 kw.No. 4"alternator. unit, an 18A Bellis.& Morcom set, was taken over by the Commonwealth Government in June 1943.

Jan 1, 1945

Detailed studies of mineral paragenesis, isotope and trace-element geochemistry, and physical mineralogy at Mount Morgan are compatible with deductions by Geopeko Ltd geologists concerning field relationships in the mine area. Considered together, field and laboratory data suggest that the Mount Morgan deposit originated from a shallow, intrusive, acid volcanic dome similar to those which produced the Kuroko-type deposits in Japan. At Mount Morgan, however, interaction with sea water was much less, the sulphides were concentrated rather than forming a group of deposits, and only the throat of a breccia vent is pre- served, so that only the lowermost parts of Kuroko-type deposits can be compared with the Mount Morgan mine. A final difference lies in the presence at Mount Morgan of a quartz diorite adjacent to the ore. Mineralogical data are compatible with post-ore intrusion, possibly up an earlier volcanic fissure.

Jan 1, 1974

The production of 100,000 tonnes per year of synthetic rutile from the processing of ilmenite, coal and copperas (iron sulphate) produces 200 cubic metres per hour of effluent water. A 2.0 hectare biological filter, comprising natural and man- made wetlands, has been built into the last stage of the effluent water treatment system. It is an area of shallow water (

Jan 1, 1988

By Liu X

The solubility of cobalt oxide in iron silicate slags has been measured at 1573 K by equilibration of silica and alumina saturated slags with liquid Co-Au-Fe alloys, and by equilibration of silica unsaturated slag with solid Co-Fe alloys, at oxygen pressures of either 10-9 or 10-10 atm (1 atm = 1.013 x 105 Pa). The activity coefficient of cobalt oxide has been calculated and compared with previous studies.

Jan 1, 1991

By Gillies A. D S, Lee A. H

Water is an integral component of a mining operation. To-date water management has received a low profile in the overall management of mining operations. To cost effectively meet the requirements of government environmental legislation the man

Jan 1, 1994

The Olympic Dam Project constitutes a major resource of Copper and Uranium and has been under intensive evaluation since the discovery in 1975.A 500 metre deep rectangular shaft has been sunk into the deposit and this has been followed by 8400 metres of level, incline and decline development. 5 surface ventilation raises have also been constructed.Large scale trackless equipment is used to carry out the development, and productivity statistics are given.The paper describes the functionalised system used in the development program and discusses the maintenance support, and services required to carry out these works.The objectives of the Exploration Development program and the satisfactory results obtained from this work are also discussed.

Jan 1, 1985

By Mutton B. K

A systematic approach to the collection, presentation and application of structural geology data is employed in the extraction of narrow en echelon Ag-Pb-Zn orebodies by rut and fill stoping at Mount Isa. The aim is to locate, document and predict areas of adverse ground thereby enabling adequate ground support to be installed in advance of production mining. The important structural features are identified and their relevance illustrated by case histories of previous failures. The methods of collection, documentation and application of data are discussed.

Jan 1, 1977