Search Documents

By Wright S

Single pellets of mixed lead-zinc concentrate containing up to 20 % lead were roasted in the temperature range of 800-1100¦C. Variables studied included pellet size (from 9-8 to 3-2 mm diameter), gas flowrate past the pellet (from 0.05 to 5 ms t), composition of the atmosphere and the effect of additives such as zinc oxide and silica. After defined periods of time, the pellets were removed from the furnace, quenched and submitted for chemical, XRD, SEM and microprobe analysis. The oxidation of the zinc sulphide followed a shrinking core model. Temperature measurements showed that very high pellet temperatures were experienced at the start of an experiment but after 5-10 minutes these approached a constant temperature. The lead loss from the pellets was then constant with time. Thermodynamics predicted the presence of two bands of lead material in the reacted layer of the pellet. These were found in practice. The lead loss from the pellet occurred from the outer oxysulphate layer via the vaporization of lead oxide polymers. The vapour pressure of PbO, and the loss of lead, was dependent on temperature and bulk gas concentrations of SO2 and 02. At 1100¦C the addition of silica greatly reduced the loss of lead from the pellet. Physical factors such as pellet diameter and gas flowrate past the pellet affected the particle dynamics. These results were found to vary in accordance with the predictions of the Froessling equation.

Jan 1, 1989

Vatukoula, the Fijian equivalent of gold rock, is the name of the community embracing the gold mines owned and operated by Emperor Gold Mining Company Ltd., Loloma (Fiji) Gold Mines, N.L., and' Dolphin Mines Ltd. It is situated in the Tavua Goldfields approximately five miles from the northern coast of Viti Levu, the largest island of the Colony of Fiji.The climate is sub-tropical, there being a definite wet and dry season. The wet season is somewhat variable in length but usually extends from December to March, during which time most of the rainfall for the year is recorded.Although the average annual rainfall is 71 in., more than twice this amount has been recorded. Precipitation at the rate of 5 in. per hour is not uncommon and 15 in. of rain has been registered in 24 hours. The mining methods adopted, therefore, had to suit these wet conditions.The occurrence of gold in the Tavua area has been known since 1872, but it was not until 1932 that discoveries were made which led to the formation of the present operating companies. In 1934 the Emperor Gold Mining Company Ltd. commenced operations, followed in 1935 by the Loloma (Fiji) Gold Mines, N.L., and later by the Fiji Mines Development Ltd., now known as the Dolphin Mines Ltd. Up to the end of 1951 these three mines had produced 2,501,688 tons of ore from which 1,277,881 oz. of fine gold and 347,429oz. of silver were obtained, realizing in Fijian currency £13,025,153.The three mines are situated close togeth.er on contiguous mining leases, and, although under common management, are operated as separate en,tities. Since 1944 all the...

Jan 1, 1953

Data collected from payload management systems at a number of surface mining operations show significant variance. Heavily loaded trucks travel slower up ramps than lightly loaded trucks. Faster trucks are slowed by the presence of slower trucks, resulting in 'bunching' and production losses. A stochastic model was constructed to simulate a truck haulage return cycle of 12.5 km at a large open pit gold mine in the USA. For a fleet of 35 trucks, the best estimate of the benefit achieved by a sustained reduction in payload variance of 25 per cent is a throughput increase of 1.6 per cent, within a possible error range of 0.6 to 3.2 per cent. This potential benefit is worthy of further investigation by Continuous Improvement teams at large open pit mines. The model also indicates that, under the right circumstances, provision of an overtaking lane can provide throughput benefits of up to ten per cent, The feasibility of providing unidirectional haulage circuits within large open pit mines should be examined.

May 1, 2010

By G W. Wilson, P Ritchie, N A. Currey

The design and rehabilitation of potentially acid forming (PAF) waste rock dumps is site specific, being a function, among other factors, of the rock types, the dumping and storage method employed, and the climatic setting. The æstore and releaseÆ cover system developed to manage acid rock drainage (ARD) from mineralised waste rock dumps at Kidston Gold MinesÆ open pit operations in the semi-arid climate of North Queensland, Australia, has been monitored for seven years. The paper describes the philosophy behind the design of the PAF dump and æstore and releaseÆ cover system and the adaptation of the cover system over time to suit KidstonÆs conditions. The results of monitoring over the seven years since the first cover was constructed are presented, and the approach being taken at Kidston to ensure that the risk of impacts from any residual ARD is accommodated and to facilitate lease surrender are described. The Kidston story is a valuable case study of a successful approach to remediating an identified source of ARD in a semi-arid climate, which has actively engaged all Stakeholders.

Jan 1, 2003

By Harmse C

Gold mining in Vatukoula had been a low tonnage/high grade operation for much of its 55-year life. During 1991 it became clear that a change in direction was needed if the mine was going to continue to prosper. The challenges of ore reserves of only three years, the prevailing gold price and high infrastructure and fixed costs combined to force changes in mining strategy.A more productive mining method was required to lower the unit mining cost, lower the pay limit and make more effective use of the resource.The flat dipping mineralised faults or flatmakes had been mined by updip, handheld room and pillar methods with a more recent trackless development adaptation. Furthermore, up to 40 per cent of the resource was left in pillars and broken rock.

Jan 1, 1993

The complexities of mining in current economic conditions, where ore extraction schedules are varied on a weekly basis so as to ensure constant supply to the process plant, can result in a number of scenarios that pose geotechnical challenges. This paper presents a case study where alterations in the mining schedule of a particular mine resulted in the necessity to mine under a large uncompacted embankment, ie integrated tailings and mine waste land form. To effectively ensure that ore recovery was maximised, a well-designed slope monitoring system to evaluate design performance and to provide timely warning of impending failures was imperative. In order for an appropriate slope monitoring strategy to be developed, a thorough understanding of the potential slope failure mechanisms, capabilities and limitations of available monitoring techniques is required. Communication of the monitoring results and response strategy to alarms generated by monitoring systems must also be carefully considered to maximise effectiveness. The results of preliminary stability modelling can be used to guide the design of a monitoring system, which in turn can then generate data which can be used to iteratively refine the geotechnical model. This paper illustrates the development and implementation of a slope monitoring system and associated communication system, using the Daydream embankment at Fortescue Metals Group's (FMG's) Cloudbreak Operations as a case study.

May 1, 2010

By Vnenk L, Hargraves AJ

Metropolitan Colliery has some areas of roof where immedi- ate support is required in development. The disadvantages of percussive roof bolting at the face have led to recent produc- tion trials with rotary boring and rapid=setting resin anchored roof bolts developed at the Colliery. The three innovations involved are: (1) the wet drilling of small holes with an all- hydraulic, portable rotary boring machine; (2) the rapidity of loading a "point anchored" resin bolt; and (3) the consistently high anchorage strength available. All three innovations provide striking advantages over the previously available alternatives. The greatest disad- vantage - that of cost of resin - is not prohibitive, and there is promise of improvement in the future. There are possibilities of variations of the techniques for special support problems in particularly difficult roofs.

Jan 1, 1971

Leichhardt Colliery is developed for underground mining of coal seams at depths exceeding 280 m. Investigations of the area were conducted in phases, each designed to delineate seam characteristics more accurately and to indicate with increasing precision the nature of local geological features and the ranges of those coal properties susceptible to variation. The investigational campaign is described phase by phase summarizing evaluation of the area at the conclusion of each phase. Predictions of geological conditions likely to influence engineering planning are contrasted with actual conditions observed during trial mining.

Jan 1, 1974

Techniques and results achieved during the excavation of the Melbourne Underground Rail Loop (HURL) are summarised and discussed in the context of the various restraints present in a typical urban construction project. Mechanical methods (as distinct from those utilising blasting)accounted for the bulk of the excavation. Ground support was critical in this particular geological excavation setting, but is not discussed in detail except insofar as it constitutes a restraint to excavation progress.

Jan 1, 1978

By G McSpadden

At September 2001 the beneficiation plant at BHP Billiton Iron OreÆs Mt Whaleback mine is set to treat 9.5 million tonnes per annum (Mtpa) of iron ore, 40 per cent better than original design. This paper describes the steps, decision-making processes and innovations used to increase capacity at minimum cost. The plant was designed in 1979 to operate at 1133 t/h for 6000 hours per annum, treating 6.8 Mtpa. Sufficient suitable contact ore was unavailable and feed was finer than planned. The plant was designed with minimum surge capacity between multiple process units. It had never reached design capacity. In 1993 a study by Fluor Daniel to treat increased tonnage resulted in modifications to improve plant operations. Efforts to expand production by increasing reliability did not achieve the desired capacity. NJ Morrow (Pty) Ltd (NJM) conducted a technical audit in 1996 with process evaluation by Mineral Processors. Replacement of operator interface and PLC logic in 1997 made plant operation and diagnosis easier. Involving operators in logic development enhanced their plant knowledge. Fluor Daniel Simulation developed a simulation model of the process. Mineral Processors and NJM reviewed the model findings, recommended metallurgical improvements and developed preliminary designs and costs. BHP Engineering produced a detailed design with a cost estimate of $A34 million. After analysis and revision of the design, a $A10.4 million upgrade to 8.5 Mtpa was carried out. Detailed modifications to the process units, particularly the HM drum plant, allowed significantly higher capacities and improved metallurgical performance. The target capacity was achieved in June 2001. Further modifications are progressing to treat lower-grade ores.

Jan 1, 2002

By J D. Bryant

The Ernest Henry Copper-Gold mine, the third largest copper deposit in Australia, is located 35 km NE of Cloncurry in the Mt Isa-Cloncurry mineral district of NW Queensland. Ernest Henry Mining Pty Ltd (EHM), a wholly owned subsidiary of Xstrata Copper Australia, operates the mine. Approximately 10.2 Mt of ore grading 1.12 per cent Cu and 0.56 g/t Au were processed during the 2001 - 2002 financial year. The Ernest Henry plant produces copper-gold concentrate, which is trucked to Mt Isa for smelting. The Ernest Henry deposit is a member of the diverse Fe-oxide-(Cu-Au) class of deposits. The orebody is hosted within a sequence of moderately SSE-dipping, intensely altered Paleoproterozoic intermediate metavolcanic and metasedimentary rocks. Copper (chalcopyrite)-gold mineralisation occurs mainly within the magnetite-biotite-calcite ¦ pyrite matrix of a 250 m + 300 m pipe-like breccia body. The breccia pipe comprises two anastomosing lenses separated by a lower grade, clast-supported breccia zone. Several anastomosing brittle faults affect the macro-geometry of the orebody. Copper grade is proportional to the degree of matrix support in the breccia. The July 2002 Ore Reserve was 88.7 Mt @ 1.0 per cent Cu and 0.5 g/t Au. Resource estimation at Ernest Henry is based on a large database of predominantly diamond drill hole information. Drill spacing is typically 50 m + 50 m. Ordinary kriging is used to estimate Cu, Au, SG and IST (oxidation indicator) into model parent cells of dimension 20 m E + 20 m N + 16 m RL. The block model is comprised of five geological-geochemical domains represented by 3D wireframe surfaces. Zonal control, where samples and blocks are assigned the same domain number, is used to control grade estimation. The geometry of the domains defines hard grade boundaries across strike and soft boundaries along strike A Deep Drilling Project was initiated in August 2002 with the initial aim of testing the down-plunge extension of the orebody to a vertical depth of over 1 km. The encouraging intersections to date have resulted in a significant increase in the mineÆs open pit Mineral Resource together with the identification of an underground Mineral Resource. Added benefits of the project included an expanded and updated geological legend and an improved understanding of the host geological sequence.

Jan 1, 2003

By R Williams, P Kohout, J Comins

The Northside Storage Tunnel (NST) is the largest tunnelling project ever undertaken in Sydney. The tunnel extends deep underground from the western bank of the Lane Cove river to the North Head sewage treatment plant (STP), with a branch tunnel from Scotts Creek connecting to the main tunnel under Tunks Park. The aim of the tunnel is to intercept wet weather overflows from four key points along the northernsuburbs ocean outfall sewer (NSOOS) and provide short-term storage and transfer of sewage to NorthHead STP for treatment prior to discharge to the ocean through the deep ocean outfall. The project was an ambitious undertaking by an alliance between the client Sydney WaterCorporationand the engineering firms of Montgomery Watson, Connell Wagner and Transfield to design andconstruct approximately 20 kilometres of tunnel, tunnel declines and shafts in just over three years. In order to achieve this tight timeframe construction of the NST has been undertaken simultaneously at seven construction sites located across the northern suburbs of Sydney. As with most tunnelling operations, tunnel boring machines (TBMÆs) and roadheaders dominated the excavation activities. Tunks Park and North Head STP are the major tunnelling sites. An access decline was excavated using roadheaders at both of these sites to facilitate tunnelling using TBMÆs. Three TBMÆs 3.8 m, 6.0 m and 6.3 m diameter) were launched from Tunks Park and one TBM (6.5 m diameter) was launched from North Head. At the overflow interception sites of Scotts Creek, Lane Cove River and Quakers Hat Bay two vertical shafts known as drop and access/ventilation shafts were constructed. These shafts would provide the linkage between the existing sewer and the tunnel. As their names suggest the drop shaft would convey the wet weather sewage overflows to the tunnel while the access/ventilation shaft would provide access during dry weather and ventilation during a filling event. The fourth overflow site of Tunks Park would use the tunnel decline as its link to the tunnel. Originally these shafts were to be excavated using the raise bore method. This technique however, is entirely dependent on the TBMÆs reaching the shaft locations at the specified time. This was not the case at two of the three shaft excavation locations and top down methods of excavation such as, a percussive cone fracturing (PCF), blind bore, mechanical excavation and drill and blast were investigated to ensure the project met its completion schedule. Traditionally project decisions are dominated by cost and schedule objectives. The contractual arrangement of the Alliance however, required that the objectives of safety, community and environment also be considered in any decision making process. Thus each of these top down methods of excavation were assessed against these five objectives. On considering all of these factors the use of explosives was considered to be the superior technique.

Jan 1, 2001

SINCE writing the above-mentioned paper, some further indicator cards have been taken from the No. 1 machine, and the writers believe that a reproduction of these cards will be interesting as illustrating the performance of the machine after fifteen month steady running, night and day, seven days per week and twenty-four hours per day, at the average speed of fifty-seven revolutions per minute (see Fig. 1, page 60). For the past twelve months no adjustment have been made in the valve setting, and the only repairs have been in connection with the springs of the poppet valves, and these but slight, the springs latterly having been removed. The cards illustrated were taken with one indicator, and, therefore, are not simultaneous, andmay show to some extent the yariations of individual strokes, and with that qualification may be taken as typical of the machine's average performance.In connection with some feed-water measurements of the winding engines a rough test was run with the two compressors, the Riedler and the Corliss, coupled to the condenser, and running at fifteen and fifty-seven revolutions per minute respectively, with the result of 15.9 pounds of steam per indicated horse power per hour. This result, though only approximate, seems to indicate that the No. 1 machine is running under the guaranteed consumption, and that it is capable of maintaining this under the severe conditions of everyday practice.

Jan 1, 1909

By D Burgess

Since the days of mandatory high cost pilot plant testing in 6 ft + 2 ft SAG mills autogenous griding/semi-autogenous grinding (AG/SAG), mill specific energy is now calculated by various empirical formulae and pilot testing carried out in small laboratory mills. Barratt (1989) described a method using Bond Indices than adding a single factor of 1.25 to arrive at the AG/SAG specific energy. In 1991 the Canadians developed the SAGPower Index (SPI), test using 2 kg of material in a 300 mm diameter mill. This test has been further developed by Starkey, Hindstrom and Orser (2006). This test now includes a Bond Ball mill work index test.The Macpherson test is still being offered by some testing facilities. This dry test requires at least 180 kg of material.Morrell (2004) formulated an AG/SAG specific energy generator based on a drop weight index Value (DWi). This DWi value is related to the Ab parameter and the material specific gravity. Morrell reconfigured the BondÆs Third Theory formula to cause extra power requirements to be inputed. This technique incorporates the material specific gravity (SG). The AG/SAG specific energy values produced using this method are susceptible to higher values of crushing and rod mill work indices.This paper offered describes a more simple method to generate AG/SAG specific energies. This programme incorporates Bond work indices, the JKMRC parameter Ab measuring impact breakage and the parameter ta measuring the abrasion rate, then employs a series of efficiency values nominated for each transition size (AG/SAG T80). These efficiency values have been compiled over the years from actual operating plants and documented reports.CITATION:Burgess, D, 2012. A method of calculating autogenous/semi-autogenous grinding mill specific energies using a combination of bond work indices and Julius Kruttschnitt parameters, then applying efficiency factors, in Proceedings 11th AusIMM Mill OperatorsÆ Conference, pp 37-44 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 29, 2012

The Porphyry Gold Mine (150km NE of Kalgoorlie) was reopened in November 1983 with production commencing in April 1984. Original reserves quoted for the open pit were 822000 tonnes at 5.2 g/t Au based on wide spaced diamond drill holes. Close spaced grade control drilling has revealed some loss of tonnage and a significantly lower grade. In the area of the pit mined to 30 June 1985 this grade control reserve estimate contained 67% of the gold in the original ore reserve with the grade being 19% lower. It is anticipated that the final grade control reserve estimate will contain around 80-85% of the gold contained in the original reserve. There has been close agreement between the Mill Head grade (4.19 g/t Au) and the grade control predicted grade (4.2 g/t Au) confirming that dilution is not a major problem. After initial poor agreement (attributed to "lock-up" in the circuit) the bullion calculated head grade steadied out at 93% of the grade control prediction. This difference is considered to represent the geostatistical bias in the drill hole/crushed rock sampling. Gold recovery has been in the range 93-95% (compared with bullion calculated grade). The net result is that the recovered grade of ore mined to 30 June 1985 is 70% of the original ore reserve grade.

Jan 1, 1986

By D Thornton

Geologists use large data sets and spend many hours and much computing time modelling the distribution of minerals throughout a rock mass. Significant investments in drilling, assaying and quality assurance and quality control (QA/QC) are made before sophisticated geostatistical techniques are applied to the collected data. A large amount of research has been done in this field such that the ore control model is a reasonably accurate reflection of the mineral that is actually in the ground. However, after all this effort, the mining engineers then work just as diligently to blast the in situ rock mass to a particle size that can be efficiently handled and further reduced by downstream comminution processes. In open cut mines, this invariably requires large amounts of explosive energy that displaces the ore boundaries from where the geologists originally defined them. Failure to accurately account for blast movement will result in misclassification, whether that is ore to waste; low grade to high grade; sulfide to oxide; or other contaminates û collectively referred to as ore loss and dilution. The financial consequence of getting this wrong is substantial and not well quantified. This diminishes all of the good geological QA/QC done in defining the ore. This paper discusses various technologies used to physically measure blast-induced orebody movement and the difficulties in modelling this with a purely theoretical approach. Rock mass structure, blast energy, design and timing contours all have significant and interrelated effects on blast movement vectors. Measured blast movement has a large variance due to the uncertainly of many of the controlling parameters û arguably dominated by the heterogeneous nature of the rock mass. Although there have been significant advances in blast movement modelling capability in recent years, this unpredictable blast movement limits their use in the context of production ore control. Certainly, without physical field measurements, accurate predictions of movement are near impossible.Limitations of traditional surface markers in determining three-dimensional (3D) blast movement within the orebody are also reviewed, and advancements in accurately measuring these vectors within blasted ore discussed

Sep 26, 2011

By Dickson T. J

Slag cleaning is an important part of the pyrometallurgical operations at the Kalgoorlie Nickel Smelter. It is a complex system with many streams of different phases and composition. Some of these streams are very difficult to control and/or monitor. Through the use of a statistical computer package, called Minitab, key relationships affecting the economical operation of the slag cleaning process have been found. Data for the statistical analysis was collected from all possible variables around the appendage.

Jan 1, 1991

The Ranger Project Area covers 78.6sq km and is approximately six km east-west by 14km north-south (Fig. 1). The area is known to con- tain two uranium orebodies, Ranger No. 1 and No. 3, two uranium occurrences, Anomalies 4 and 5 and three significant radon anomalies, Ranger 18, 19 and 48. The Ranger No. 1 and No. 3 Orebodies con- tain approximately 120 000 tonnes of U308 in highly chloritised metasediments of the Lower Proterozoic Cahill Formation. The orebodies occur as suboutcrop and exhibit significant radiometric anomalies. These occur within approximately 400m vertically of the projected unconformity with the sandstone of the Middle Proterozoic Kombolgie Formation. Oxidised and reduced uranium minerals occur in quartz-rich schists containing variable muscovite, chlorite and sericite and in the chloritic matrix of chert breccia. Secondary uranium minerals namely saleeite, metatorbernite and gummite associated with earthy iron oxides occur from the surface to 50m depth in No. 1 Orebody and up to 80m depth in No. 3 Orebody. Below the oxidised zone, uranium occurs as pitchblende finely disseminated throughout sequences of quartz muscovite chlorite schist up to 150m thick and as open space fillings in zones of structural deformation. The uranium-bearing schists directly overlie up to 300m of dolomite and magnesite containing minor interbedded schist units and are themselves overlain by approximately 2 000m of more micaceous schists of the upper part of the Cahill Formation. Regional metamorphism has occurred to at least amphibolite facies and has been followed by retrograde metamorphism to a greenschist facies equivalent. The metasediments are intruded by granitic pegmatites and dolerites. Uranium is associated strongly with chlorite of which there are at least five textural varieties. Not all of the various generations of chlorite have associated uranium. Graphitic schist horizons occur which are often less than one metre thick and discontinuous. These are best developed at the base of the quartz chlorite schist sequence where uranium grades up to 1 000ppm U may extend for several hundred metres beyond the main ore zone. Uran- ium is not common in the carbonate sequences and only occurs in chlorite segregations in disrupted zones. The unoxidised ore contains sulphides, mostly pyrite, which are low in abundance (

Jan 1, 1984

By B Ilich, M Brad, R Brandli, E MarT

The Wirtgen surface miner was investigated for application to the Cloud Break iron ore deposit since it can selectively mine thin seams and there is no requirement for drilling and blasting or primary crushing as the surface miner cuts and breaks the rock to secondary cone crusher feed size. A physical metallurgical study of the surface miner run-of-mine (ROM) from Cloud Break was conducted to better understand the product size distribution, amount of -31.5 +6.3 mm lump produced, lump stability and physical metallurgical quality compared to conventional drill and blast techniques. Since the Cloud Break mine was not in production, the lump product from crushing and screening of surface miner ROM was compared with product simulations using traditional premining physical metallurgical processing techniques including drop testing of PQ diamond core. Drop test conditioning is widely used in the iron ore industry to simulate blasting, crushing and screening at the mine and subsequent product degradation during handling from mine to port to predict both the amount of lump product on ship and the size distribution of the fines and lump. The size distributions of surface miner ROM for hard, medium and friable ore types show very tight size distributions with very little above 100 - 150 mm, about 60 per cent of the distribution between 75 and 6.3 mm, with less below 1 mm compared to conventional drill and blast ROM. Crushing, screening and drop test conditioning of the surface miner ROM produced more lump in equivalent ore types compared to drill and blast techniques or their breakage simulation using PQ diamond core. The higher lump yield from the surface miner was also confirmed by pilot scale crushing of some 7400 t of surface miner ROM from the Cloud Break trial pit. The lump produced from surface miner ROM was quite stable and showed similar low degradation characteristics to lump simulated from drill and blasting techniques. Product size distribution simulations using conditioned crushed lump from 1 m diameter Bauer hole samples were found to compare well with processed PQ core samples and surface miner product from trial mining at Cloud Break. The Bauer sample method is therefore considered to be a very useful close simulation to actual lump production, although the lump yield is lower.

Jan 1, 2007

By M Miller

Operators of nickel laterite pressure acid leach and gold pressure oxidation technology frequently employ a series of steam condensing heaters to preheat the leach feed slurry. The heaters are an economic pinch point û although the thermal performance of the heaters is critical to overall process viability and operating cost minimisation, they are also a significant capital item and must be sized accordingly. Despite this, discussions of the factors underlying heater design are conspicuously absent from technical literature, and existing operations feature a conflicting range of heater sizes and configurations. This variety would suggest that at least some of the chosen heater designs are oversized. As part of its detailed design stage, the Ravensthorpe Nickel Project (RNP) constructed and tested a pilot plant heater to develop an understanding of the heating process and to ensure that the RNP heaters were appropriately sized. This testwork used RNP slurry at design density and viscosity on a 450 mm diameter, 6500 mm high column. The pilot plant testwork demonstrated the intrinsic efficiency of the direct steam condensation heating process, which was essentially independent of slurry density and viscosity. Presence of non-condensable gases in the steam phase decreased the heat transferred in certain circumstances, but heater performance remained consistent with thermodynamic limitations. Stagewise heat transfer within the column was rapid, and suggested either a very high slurry surface area or excellent heat transfer within the slurry phase. While the testwork did not set out to distinguish between these effects, physical evidence pointed to droplet formation in the inter-tray shower zone, giving a high heat transfer area. For scale-up purposes, the key facts were that the heat transfer rate was not limited by using high viscosity slurries and heaters could be designed using the principles applied to the smaller of those in existing operations. This paper discusses existing slurry heater designs, the current understanding from open literature, the pilot plant testwork, results and analysis, and scale-up to commercial sized equipment.

Jan 1, 2005