Search Documents

By T

THE Sulphide Corporation's works for the smelting of ores containing lead, gold, and silver are situated close to the Cockle Creek railway station, on the main Northern railway line, and are about 95 miles from Sydney and 10 miles from Newcastle. A branch line runs to the works, and siding accommodation and bins are provided for expeditiously handling all ores sent for treatment. The Corporation also possesses wharfage facilities at the port of Newcastle, where consignments of ores arriving by sea can be handled direct into railway trucks for conveyance to the works.The greater portion of the ore treated at Cockle Creek comes from the Corporation's mine at Broken Hill, but a large quantity of other grades is also purchased and treated.

Jan 1, 1918

By R Huntley, D Sims

Pajingo gold mine produces over 240 000 oz Au per year from underground mining using longitudinal bench stoping methods with a 15 m sublevel interval. Average mine head grade is around 12 g/t Au, contained within quartz veins between 0.5 to 16 m wide. The veins dip steeply (>60¦) and exhibit strike variations which lead to many curved and meandering drive/stope geometries. Unplanned dilution at Pajingo is predominantly controlled by fault planes that subparallel the vein and commonly lead to slabbing failure from the stope walls. Initial efforts at determining maximum spans were based on using the Stability Graph method of stope stability. However the method had a number of shortcomings that did not address mine site observations, including previous mining, interaction of different joint sets and the presence of discrete shears which resulted in poor prediction of stability. A method was developed to rate the risk of dilution for a stope based on observations made in the ore drives. The method utilises profile mapping of the ore drive, structural features observed and the orebody itself, on 10 m spaced sections along the ore drive. A matrix of factors determines the dilution risk for stoping at the time of mapping and the rating is transferred to longsection plots in the office. The dilution risk rating is used to determine the position and density of cable bolt support aimed at lessening the risk, and can be used to review blasthole designs prior to finalisation. The method has been used for more than two years and has proven to be a good indicator of potential unplanned dilution (ie waste outside of ring design). A recent review of the dilution risk mapping process has indicated it is assisting in reducing the impact of dilution at the operation and has the scope to be utilised further in the design process.

Jan 1, 2002

By G Billing a, D Gribble, E Hall, D Varga

The theoretical benefits of electronic detonators have been reasonably well documented. To support this, a practical comparison was made between the performance of the standard shock tube system, NONEL, and a high precision electronic system, HotShotÖ, at the Sunrise Dam Gold Mine. The expected benefits from electronic detonators to Sunrise Dam were identified prior to the trial. Based on these, a number of objectives were set to demonstrate the value of the HotShot system. These are an improvement in fragmentation leading to an increase in productivity, less oversize rehandling, increased throughput and more uniformity in muck pile movement. To maintain the integrity of the trial, the nominal timing of the shots was kept exactly the same, thereby restricting any performance improvements to the precision of the electronics. Accordingly, adjacent shots were chosen with consistent geology. Video footage was taken of the blasts and vibration monitoring was carried out by fixed geophones throughout the mine. Spot heights of the muck pile swell were taken immediately after the blast and heave profile graphs were generated for comparison. Video footage was taken for a period of three hours for both shots to analyse cycle times of the excavator and trucks. PITRAM data was also collected for analysis. As far as practicable, the ore was taken to the same finger on the run-of-mine (ROM) pad to assist in single sourcing for the crusher and to allow oversize to be separated out. From specific metrics taken during the trials, it was shown that the expected improvements due to the high precision timing of electronics were realised in all areas.

Jan 1, 2007

By Churchill J

A suite of software programs has been written to provide the field engineer or geologist with the capability to collect and store data directly into small, portable handheld computers. This allows the engineer and geologist to collect data in a more efficient manner as the data is collected in sequence and is verified at the time. Typical applications for this software include geological and geophysical logging, trucking surveys, mine surveying, condition monitoring, ventilation surveys and maintenance systems. The software allows the user to construct his own electronic notebook by structuring data input to the computer in a similar manner as is now done on pre-printed forms. The user can store all valid entry codes or numeric ranges in a dictionary and all data inputs made are validated against this dictionary. Once constructed the user may call the electronic data sheet into the unit and collect data which will be stored into the unit which has the memory capacity to record data for up to periods of 60 hours. The data can then be automatically transferred to mini/microcomputers for immediate analysis and report generation. The software may be used on a variety of handheld computers.However the generally rugged environments found in the mining industry limit the choices. In particular the authors have selected a unit weighing a little over one kilogram, which is rugged enough to fall off an underground survey vehicle, and survive when accidentally immersed in water,without losing data. This paper describes the software developments in detail. The project development work to produce this system has been funded by a grant from the Australian Mineral Industries Research Association and is supported by a number of large Australian mining companies.

Jan 1, 1986

The structural pattern of Victoria shows the presence of EW, NW, NE as well as the more readily recognised NNW factors commonly associated with the goldfields. ENE and WNW trends are also present. This structural lattice affects all rocks of the State. Landsat imagery shows that the EW, NW and NE structural elements are closely related spatially to the distribution of Palaeozoic igneous intrusives, Cainozoic volcanic vents as well as all historically important gold mines. It is suggested that the EW, NW and NE structural grid visible on landsat imagery is a reflection of the structure of a mid-crustal layer situated between 3.5 and 17 kms below the surface. The points of intersection of the structural elements of the mid-crustal layer offer most favourable loci for the escape of energy in the form of heat. The correlation between the distribution of igneous plutons, volcanic vents and centres of mineralisation, all reliant on high levels of energy for their formation, indicates the stability of the structures of the mid-crustal layer since early Palaeozoic times. The deep level crustal structures are believed to be, related to the release of stresses placed on the crust since early Palaeozoic times by the rotation of the Earth. A geological model that accommodates the presence of a mid-crustal layer as well as the complexities of the recognised orogenic cycles of southeast Australia is suggested. All 1 000 kg Au reef and deep lead mines fall within 1.5 and 2.5 km respectively of strong linears associated intimately with plutons and volcanic vents. Future exploration of the State is more likely to meet with success if it too is confined to the evaluation of these and similar linears. The mode of mineralisation of any one centre will depend upon the temperature, pressure and geochemical gradients operating on the migrating mineralising fluids as well as the structures in the host rocks. These factors are likely to have varied considerably from one centre of mineralisation to the next and consistency of mineral isation form and depth should not be expected along the length of any single Linear.

Jan 1, 1986

I would like to build on the keynote address given by Peter Stoker to the Fourth International Mining Geology Conference (2000) entitled æThe Role of the Mine GeologistÆ. He concluded that à the important aspects of the professional contribution of a mine geoscientist to a mine operation include: The geoscientists prime task is to maximise the profitable extraction of the ore deposit on which they are working û that is to add value. They must maintain and develop their own expertise. By ensuring a truly professional approach to all they do, they will provide the best service to the community, to their company or client, their shareholders and their family or close associates. In that process they will also assist in protecting themselves in this increasing litigious world. I intend to build on these points and, in particular to expand on what it really means to take a truly professional approach to mine geology. Mine geology is different from other forms of geological practice. As a mine geologist you are the advocate for the orebody. After all the orebody is the one thing that is unchangeable.

Jan 1, 2003

In the course of an investigation of the influence of bismuth on copper carried out some years ago, (1) the author found that phosphorus exerted a beneficial effect on bismuth-copper alloys of low bismuth and oxygen content by neutralizing the embrittling effect of the bismuth. In the intervening years, a further examination of bismuth-phosphorus-copper alloys has been canied out and the influence of other elements and combinations of elements on copper containing bismuth has been studied.The results recorded in the present paper are part of this investigation.MATERIALSAll the alloys were made from high-grade copper (KS.A. wire-bar) of the following composition: copper 99·95%, oxygen 0,040'%, iron 0·0015%, sulphur less than 0-001%, bismuth less than (j>'OOl%, other elements each less than O· 0010/<-. The bar was hot rolled and cold drawn to strip which was cut into short lengths and cleaned in nitric acid ready for melting.A piece of this 'strip was drawn to wire 0·08 in. diam., annealed at 5000 C, and measured for electrical conductivity as a check on purity. The result was 101·5% of the I.E'.C. standard.In making the alloys, phosphorus was added as 14% phosphor-copper, bismuth as 17% bismuth-copper, and the other constituents either as copper alloys or as elements of a high degree of purity.PREPARATIQN OF STRIPSThe charges were melted in plumbago crucibles (Morgan salamander brand) in an oil-fired furnace, Le;, in the manner commonly adopted in industrial practice. The copper was first melted under charcoal, well stirred with a chaned stick, and the necessary alloying elements added and stirred in with the stick. The weight of a charge varied according to requirements but generally was about 4 lb. The charges were poured into slightly tapered brass moulds heated to about 1000 C and dressed with a mixture of mineral oil and tallow. They were not only poured under charcoal through the burning mould dressing but also- through a ring of flame produced by burning kerosene on asbestos cord wrapped round the top of the mould. Experiments carried out with plain copper proved that by this means oxygen could be excluded from the stream of metal. The billets were 7·5 in. long x O·83 in. diam. x 1·3 lb. weight.The billets were cropped about 1 in. from the top, cleaned in nitric acid, and measured for density by the usual method of weighing in air and -in water. As these measurements were required only as a check on casting, technique a high degree of accuracy was not essential (accuracy = -+ 0·2%).

Jan 1, 1942

By N Slade, D Kennedy

Optimal throughput is a key objective for the successful operation of any manufacturing or processing business. In the mining industry in particular, in order to obtain maximum return on the significant capital investment in the physical assets involved, ensuring continuous throughput is a major focus for the complete leadership team. Failure to meet throughput objectives becomes a major source of distraction for management which too often attempts to solve shortfalls by æforcingÆ and æenforcingÆ production targets. This focus on the short term and the lack of attention to addressing root causes frustrates operators who attempt to satisfy unattainable short-term targets and lose sight of the long-term goal. Mount Isa Copper Operations, Xstrata Copper, North Queensland, had ambitious plans to increase throughput volume by ten per cent within a four month period to allow budgets to be achieved within the financial year. To achieve this, the process had to overcome the interplay of a multi-node (æsiloedÆ) production system and its associated inventories, each node, of which on the face of it at least, had more than enough ænameplateÆ capacity to meet these plans. However, the actual volume achieved at the end point of the system was well below this nameplate capacity and the system operated with an extraordinarily high standard deviation. The key issues in terms of making or exceeding plan were: how to substantially reduce the variability of the system and managing the inventories between nodes, how to synchronise throughput between the production nodes, and how to improve the decision-making ability within the process. In this paper, the implementation team has shown that a revolutionary process view of the operation together with appropriate planning decisions allowed increased throughput to be achieved without further capital investment.

Jan 1, 2006

By Misk A

Several logging methods are presently available to the oil industry for the evaluation of formation porosity: the Sonic and Neutron logs are already widely used, the Gamma-Ganmia log is being progressively introduced. The readings of these instruments are primarily a function of the rack-porosity, hence the general term of "porosity tools". Apart from porosity, however, other variables such as type of fluid in the pores, nature of matrix and degree of shaliness have an important influence.The response of each device is a different function of such parameters: therefore, a cci bination of porosity tools can lead to information on these variables in addition to the evaluation of effective porosity.For example, the presence of gas; rather than water or oil, in a formation which is not deeply invaded, will tend to give Neutron derived porosity values which are too 'low; on the other hand, the Sonic derived porosity: value will be too high in such- a case. For the same porosity, the Sonic gives a longer transit time in sandstone than limestone, whereas in the low porosity range, the Neutron will read more counts per second in a sandstone than in a limestone of the same porosity. The presence of shale also affects the readings of the various porosity tools in different ways so that the combination of two or more methods may lead, in some cases; to an evaluation of both the-effective porosity and the shale, content.In conclusion, it may be said that the various porosity tools pre-sently available, are, to a large extent, complementary, and that in many problems the use of two porosity tools, instead of one, is very likely to bring valuable additional information.

Jan 1, 1962

By M Fimeri, R Williamson

Sample sizing in the iron ore industry requires significant manual effort to collect, transport, and sieve the samples as well as record, process and report the data. Efforts have been made to automate this process, which essentially emulate the manual process, except that a person is replaced by a robot. Even in these cells, the sieving and sizing operation consumes a significant proportion of robot time. The proposed doubling of production from AustraliaÆs iron ore mines over the next five years will place increasing pressure on sample sizing and interest is increasing in alternative automated methods. One such method is the adaptation of computer vision technology which has been successfully introduced into the mining industry in a range of applications including feed size distribution to SAG mills and oversize detection from screening stations. The limitation of this technology is that only the top surface is visible and this is used as an indicator of total size distribution. Obviously in a sample plant, where 100 per cent of the sample must be measured for acceptable quality assurance, this approach is unacceptable. In order to capture 100 per cent of the sample using computer vision technology a monolayer must be formed either by spreading the sample across a moving surface, such as a conveyor or vibrating platform, and passing this under a camera. This will become a æsurgingÆ load which presents specific problems for some types of computer vision systems, namely those relying on a 2D approach. In this paper a 3D computer vision technology will be described which overcomes the problems associated with measuring particle size in a monolayer and experimental results will be presented which demonstrate its effectiveness for lump and fine iron ore sample size measurement.

Jan 1, 2008

By Millett R

In January 1989, Western Mining Corporation (WMC) acquired the Perseverance and Rocky's Reward orebodies and associated infrastructure from the Agnew Mining Company (AMC). AMC had closed the operation in August 1986 and it had been on care and maintenance since that time. To return the operation to full production as quickly as possible it was planned to mine the Rocky's Reward orebody by opencut mining and treat this ore whilst the underground Perseverance workings were rehabilitated. Removal of overburden from Rocky's Reward thus commenced immediately with a target of April 1989 for delivery of the first ore to the concentrator. Extensive rehabilitation and upgrading of the concentrator commenced in late January, and continued in stages for an 18 month period. The first stage consisted of overhauling all existing equipment and completing a crusher upgrade commenced by AMC prior to the mine closure. During this period, it was necessary to recruit a workforce and re-establish all the required support structure. In late April the plant commenced commissioning trials on mullock. The first ore was crushed on the 11th May 1989 and concentrate produced the following day. From May 1989 to June 1990 the plant was producing nickel concentrate whilst further upgrading continued. During this period, the flotation capacity was tripled by installation of a bank of eight Wemco 144L flotation cells in rougher-scavenger duties and two 12 metre by 2 metre diameter columns in cleaning duties. The existing vacuum drum filters were replaced by two Larox PF32 pressure filters, eliminating the need for solar drying and allowing the flash drier to be fed direct from the filters. These, along with a major borefield expansion and further work to the crusher increased the nominal plant capacity from 600,000 to 1,000,000 t/yr. The plant achieved the 1,000,000 t/yr rate in April 1990.

Jan 1, 1991

By E Ben-Dor, D Bakun-Mazor, Y Ben-Ari

Determining the mechanical properties of rocks is important for various civil engineering fields, including the mining of raw materials for aggregates used in the construction and paving industries. Traditionally, the mechanical properties of rocks are obtained through in situ and laboratory tests during geotechnical surveys. However, these time-consuming surveys involve many resources. In contrast, hyperspectral remote sensing methods make it possible to identify the mineralogical composition and crystallographic structure of the rock; properties that control the mechanical properties of the rocks. In this work, we characterise the mechanical properties of carbonate rocks by using a hyperspectral sensor in laboratory conditions. We collected about 150 cylindrical samples of carbonate rock, with a wide range of strength values from several rock outcrops in Israel. We used a point spectrometer in the range of 0.4–2.5 μm and a spectral image sensor in the range of 3.0–12.0 μm, scanning the samples to obtain the signature of their light reflections and spectral emissivity. We then measured the samples’ density, porosity, water absorption, and uniaxial compressive strength (UCS). We used sophisticated data mining to find statistical relationships between the hyperspectral signatures of the samples and their mechanical properties. We used this data to identify the most dominant wavelengths for predicting mechanical properties. We found that the density, porosity, and water absorption of carbonate rocks could be confidently predicted based on spectroscopy data, while the UCS of the rock could also be predicted, but less significantly. The results of the study pave the way for the development of measuring tools for the mechanical properties of rock, based on non-destructive tests of quarrying materials.

Nov 29, 2022

By Smitham J. B

A selection of Australian washed coal samples was examined to determine the effect of sample hydrophobicity (rank) and particle size on froth stability in the flotation process. The results indicate distinct rank-based variations in froth volume and stability for flotation tests conducted without the use of collector, over a series of particle size distributions.High-rank coals showed a greater tendency to generate stable, high-volume froths than coals of lower rank. Implications for circuit design and operation are outlined.

Jan 1, 1988

By Adamiak Z. P

A study has been made of the influence of bentonite type on the wet strengths, dry strengths and drying rates of pressed iron ore pellets. Measurements of the influence of bentonite on the kinetics of growth of pellets are also reported. The results show that bentonite decreases the rate of growth of pellets and the drying rates of pellets while increases are observed in both wet and dry strengths. The results have been interpreted in terms of the physical and chemical charact- istics of the bentonite and the suitability of a given bentonite for particular pelletising operations has been discussed.

Jan 1, 1973

Organic dyes such as nigrosine and sun yellow act as depressants for carbonaceous particles in the, flotation of sulphide ores. Depression is achieved when initially hydrophobic organic surfaces are made hydrophilic by preferential adsorption of dye molecules. Experimental studies, mainly on Mount Isa ores, indicate that dyes are adsorbed as planar anionic micelles attached to carbonaceous surfaces by van der Waals and ion exchange attractive interactions. Relationships appear to exist between the amount of organic matter on the surface of ground particles, the surface area of the particles, the "saturation" adsorptions of dyes, and the degree of difficulty experienced during froth flotation.

Jan 1, 1975

By W A. Ducker, R-H Yoon, M Mao

Froth flotation relies on an attractive force between a particle and a bubble to selectively extract particles from a mixture. The range and magnitude of this attractive force is an area of ongoing investigation. We describe measurements of the effect of dissolved gases on the long-range attractive surface forces between a silica plate and a glass sphere in aqueous octadecyltrimethylammonium chloride (C18TACl) solutions. The measurements follow on the work of Sakamoto et al (2002) who have concluded that long-range interactions occur in air-equilibrated surfactant solutions but not in degassed solutions. In the present work, we have measured attractive forces that have a much larger in magnitude than the expected van der Waals force in solutions that were degassed by the same procedure used by Sakamoto et al (2002). We find that the forces are most attractive at 5 + 10-6 M C18TACl, which is close to the charge compensation point (ccp) of the glass sphere. At this concentration, the attractive force decays exponentially with distance and the decay length is 34 in air-saturated solution, and 38 nm in degassed solutions. In both air-equilibrated and degassed solution, the force is quite sensitive to the concentration of surfactant. The force is also sensitive to the pH. We note that our degassing procedure increases the pH of the solution from about 5.7 to 6.6 (presumably by removal of dissolved CO2). We find that the forces measured in degassed solution can be reproduced by using a solution that was equilibrated in air, then the pH was increased by addition of NaOH. Therefore, we conclude that the main effect of degassing in our experiments is to raise the pH. We show that the range and magnitude of the attractive force decreases in the presence of salt (NaCl). This suggests an electrostatic mechanism for the attraction. Possible mechanisms for the attractive force are examined, including the mechanisms that rely on a patchy coverage of surfactant on the silica surface.

Jan 1, 2005

By Cook B, Cunningham J

At Mount Isa Mines, a system has been developed for general monitoring of underground mobile equipment. It can provide unit condition monitoring data such as oil pressures and motor temperatures as well as production type information such as unit location and load. The system does not rely on an expensive data communications infrastructure, using instead inexpensive radio base stations which automatically transfer data from mobile units to a surface database server on the company-wide computer network. This paper includes a general overview of the system and a discussion of the practical benefits it is expected to generate.

Jan 1, 1995

By Kepplinger W

The COREX process is a technology for production of liquid hot metal on the basis of coal (without the use of a coking plant) developing by VOEST- ALPINE AG, Austria and its subsidiary company Korf Engineering GmbH, Federal Republic of Germany. CORED is a registered trademark of VOEST-ALPINE AG and Korf Engineering GmbH. The COREXW process is based on the idea of separating the process steps realized in the blast furnace (gene- ration of reduction gas, reduction of iron oxide and melting of the reduced iron) and including partial coking of the coal.

Jan 1, 1987

By Linge H. G

The effect of the presence of ore pulp on the adsorption rate of gold on activated carbon has been studied. A substantial reduction in the rate occurs when the pulp is present. The reduction in rate appears to be caused by two effects: permanent carbon pore blocking by ore particles and temporary shielding of the carbon particle surface, slowing gold access to the carbon due to the physical presence of the fine pulp. There is no significant effect arising from the presence of a pulp viscosity modifier even for conditions when mass transport dictates the loading rate of carbon in clear Solution.

Jan 1, 1987

By Kelly GD

Prior to 1986, users of satellite based remotely sensed data were almost exclusively reliant on the United States Landsat series of satellites to monitor our Earth's resources. This situation changed when France, Belgium and Sweden launched SPOT-1 in 1986. The year of 1988 saw the Japanese also enter into the earth resource satellite business. The Japanese launched an earth resource monitoring satellite with an emphasis on marine resources, hence the name MOS-1 (Marine Observation Satellite). Many more remote sensing instruments are planned for launch by these nations and others in the next 10 years.

Jan 1, 1990