Search Documents

At the LKAB, Iron Ore Mine, Kiruna, Sweden a preliminary investigation into the reliability characteristics of a fleet of load-haul-dump machines has shown that the hydraulic system is one of the most critical parts. Therefore, hydraulic system was selected for study and analysis through condition monitoring devices so that failure can be controlled or at least the failure consequences can be minimized.The hydraulic system has two different problems; one is that the contamination level is too high and the other is high temperature during operation. At high temperature, seals and tubes are a problem, because they stiffen due to carbonization, which leads to increasing leakage. The pumps and restrictions were responsible for the main temperature increase.

Jan 1, 1991

By Mandzic E. H

The Dome Mine of Timmins Mining company is located in South Porcupine, N.W. Ontario. The orebody being mined partially lies in the No. 3 shaft pillar. Stability analysis has been carried out to establish the influence of nearby mining on ground movement in the shaft vicinity. Mathematical modelling of shaft displacement has been done for stope layout at depths from 180-210 m and distances of 10-50 m from the shaft. Analysis indicated that ground displacement around the shaft is below 1 mm/m and one third less for cut and fill than in the case of open stope mining. The result of the investigation was later confirmed by cut and fill mining of this orebody.

Jan 1, 1986

By W A. Peppin, D N. Riley, N W. Schulenburg

In June 2008, a joint airborne collection using hyperpspectral systems was tested on a single Twin Otter aircraft. This experiment was designed to incorporate two airborne hyperspectral sensors for geological and environmental projects. Mineral exploration and environmental impact statements are two areas where full spectrum hyperspectral data can document the mineralogy at the surface prior to mining operations. Many previous hyperspectral remote sensing collections were collected on a single aircraft with a single sensor. Mineral mapping using hyperspectral sensors that measure in complimentary regions of the electromagnetic spectrum is cost effective as it allows for the mapping of clays, sulfates, carbonates, feldspars, quartz, garnets and many other minerals. This report describes the experiment using the following two hyperspectral sensors: ProspecTIR, a visible near and shortwave infrared (VNIR-SWIR) sensor with 356 channels and spectral range of 0.4 to 2.5 ¦m, along with a spatially enhanced broadband array spectrograph system (SEBASS), a midwave and longwave infrared (MWIR-LWIR) sensor with 128 channels from 2.5 to 5.3 ¦m and 128 channels from 7.6 to 13.5 ¦m. SpecTIRÆs ProspecTIR system and The Aerospace CorporationÆs Spatially Enhanced Broadband Array Spectrograph System (SEBASS) are pushbroom sensors, have high signal to noise ratios, have similar swath widths and instantaneous fields of view. Examples of data collection experiment will be shown with a focus on mineral/lithologic identification and mapping along with environmental assessment in the western United States. An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation.

Jan 1, 2008

By A Tomsett, R Kidd, Z Casley

Bivariate recoverable resource estimation aims at predicting the recovered metal for a secondary variable when a cut-off is applied to a primary variable. The choice of a consistent geostatistical model is advisable to allow a robust estimation from exploration data of the primary and secondary metal recovery functions on a generic selection block (selective mining unit û SMU) within large panels. Ore processing decisions at Lihir Gold LimitedÆs Lihir Gold Mine are based on the gold and sulfur estimates of SMUs from production (grade control) data. The predictive model from exploration data at Lihir is based on the estimation of a recoverable resource for gold by Uniform Conditioning (UC), with an estimate of the sulfur grade being provided by Ordinary Kriging of panels. While univariate UC is adapted to the diffusive nature of the gold mineralisation (Ladolam orebody) at Lihir, the independent estimation of sulfur, through ordinary kriging, fails to capture the potential spatial correlation that exists between gold and sulfur mineralisation. This paper presents a practical implementation of bivariate UC, which better represents in the resource model the spatial correlation between gold and sulfur. Incremental economic gains through improved definition of material categories and scheduling are investigated, and the particular impact on the process of geological interpretation and domaining is emphasised.

Jan 1, 2009

By Klenowski

Rational design of layouts for longwall operations is greatly facilitated by use of an accurate and economical method for predicting stresses and displacements. The displacement discontinuity method (a form of boundary element method) is based on replacing actual excavation geometries by thin slits of the same plan area. This approach allows three-dimensional stress- analysis at a fraction of the cost of alternative methods. The analyses can be readily performed on economical microcomputers, putting the analysis capability within the reach of mine-site personnel. This paper describes investigations associated with the German Creek Central Colliery, the first longwall operation in Queensland's Bowen Basin. The material properties used in the model, in particular the rock mass and goaf properties, have been 'tuned' to fit stress measurements obtained during extraction of the first and second longwall panels at the mine. The study shows that model predictions based on suitably scaled anisotropic rock strata properties are in good agreement with the stress measurements made to date. This model predicts average chain pillar loads significantly higher than predicted by models based on United Kingdom conditions. A working chain pillar design method is proposed using average pillar loads predicted by the numerical model and ultimate strength characteristics given by Bieniawski's formula.

Jan 1, 1988

Development of the Greenvale orebody, containing 40,000,000 tonnes of nickel ore, began in 1971 and production commenced in 1974. Annual capacity is 2,800,000 wet tonnes. The variations in ore grade and physical characteristics which occur throughout the ore- body had a major influence on the selection of mining methods, grade control procedures, and equipment. After removal of overburden by scrapers, ore is excavated by draglines sidecasting into windrows. Feed to the crushing plant is .reclaimed by front end loaders into rear dump trucks according to a grade selection pro- gramme. After crushing, ore is stockpiled into blended units of ore of required quality. Ore is stacked and reclaimed for train loading using techniques designed to give maximum mixing of ore characteristics through Bach unit. These procedures are repeated on discharge at the plant site at Yabulu. The railway, constructed by Queensland Nickel Pty. Ltd. to Q.G.R. standard, and operated by the Q.G.R., is 216 km long and includes eight major bridges and three tunnels. Two trains per day, one of four locomotives and 92 waggons, and one of three locomotives and 69 waggons, haul crushed ore to Yabulu. Train loading is semi-automatic. A small township and associated services have been constructed for employees at Green- Vale.

Jan 1, 1974

By Howell M. W

The purpose of this paper is to outline the main points in the construction of the various types of wire ropes more commonly used for winding in Australia; and the maintenance of the ropes, and cage and skip safety gear as practised at the South mine, Broken Hill.It should be mentioned that both of the shafts at present in use are dry, and both downcast with or without the assistance of the two exhaust fans normally in use: Night shift and week.-end overtime are practicaly non-existent.Thus, during night shift, the cages in No. 7 shaft are landed on the chairs at the surface, providing efficient covers for the· shaft, and allowing the maximum amount of rope to be wound on to the drums. This also applies to the cages of both No. 7 and No. 4 shafts during the week-ends.These factors, combined with electric winding and skip haulage, are calculated to obtain the best use of the ropes when properly attended.WINDING ROPES-TYPE AND CONSTRUCTIONThese ropes may be divided into four main types which will include the more commonly used constructions(a) One-size strand.(b) Warrington strand.(c) Flattened strand.(d) Locked coil.1. One-size strand as the name implies, is a rope the strands of which are constructed 9f wire of the one size.Usually the strands are of 7, 19 or 37 wires.

Jan 1, 1940

Grade control is an important factor in the on-going success of a mining operation. Grade control criteria will vary depending on the commodity being mined. Financial considerations determine the actual grade control criteria at any one mine site. Mining and metallurgical capital and operating costs are ultimately used in ascertaining cut-off grades employed in grade control. The metallurgical characteristics of the ore, and ultimately the equipment selection and design of the plant, are based on samples provided by the exploration geologist. Ore variability is an important factor in designing the process plant. Ore variations, outside of those catered for in the design, as well as large ore changes on a daily basis, will impact on the metallurgical performance, and hence the economics of a mining operation. Therefore good liaison between the grade control geologist and metallurgist will undoubtedly lead to a more consistent, and more profitable mining operation.

Jan 1, 1993

By Paley N, Cameron A, Townson P

Although blasthole deviation is a problem which can seriously affect blasting operations, there is little practical emphasis on controlling this deviation and no practical emphasis on understanding its practical behaviour. The most common way of dealing with it involves tight control over drill set up and surveying hole paths. The surveying might involve simple collar location and inclination measurement to estimate the hole's actual path. At best, some operations routinely survey hole paths after all holes in a stope have been drilled. In addition, although there is an expectation that holes will deviate, there is no planning for this behaviour in order to reduce its impact on the blast. Design decisions are invariably made with the assumption that holes are straight. If and when surveys reveal problems it is possible only to adjust charging and initiation to 'work around them'. In extreme cases the drill might be recalled to fill in gaps. The lack of planning and the lack of understanding are doubtlessly linked.A model is presented that will predict the expected path of a drill hole. By knowing how a selected few holes deviated it is possible to make a good estimate of the deviation of other holes in the same rock mass. After minimal calibration the model can be used to increase the amount of information for a given amount of surveying or the amount of surveying can be reduced while maintaining the same level of knowledge of blasthole deviation. Equally important is the ability to plan for the deviation in future drilling through altering the initial collar angles or drilling from different locations. It is the authors' hope that planning for hole deviation becomes as much a part of the design process as planning for detonator delay scatter and explosive performance variation.

Jan 1, 1992

By W J. Bruckard, M J. Vaisey

Ashton Mining Ltd (Ashton) and Lynas Corporation Ltd (Lynas) have established a joint venture partnership to develop and process rare earth oxides (REOÆs) from the Mt Weld deposit in Western Australia. The deposit is located in a deeply weathered volcanic carbonatite structure that contains approximately two million tonnes of rare earth oxides at an average grade of 20 per cent REO. As part of the 1999/2000 feasibility study currently being undertaken by Ashton and Lynas, an extensive laboratory beneficiation test program was undertaken by CSIRO Minerals on diamond drill core samples from the Mt Weld orebody. The aim was to develop a flowsheet, based primarily on flotation that could be confirmed at pilot plant scale. The target concentrate grade was 52 per cent REO with a REO recovery of at least 35 per cent. Two main ore types, nominated as CZ (limonitic siltstone) and LI (nodular limonitic ironstone) were identified for separate laboratory evaluation. The lower grade LI-type ore overlies the higher grade and more extensive CZ-type ore. The majority of the work was conducted on the CZ ore; only limited testing of the LI ore was undertaken. The latter contains a clay component that will present difficulties in processing due to its poor filtering and settling characteristics. Two processing options for treatment of CZ ore were presented for pilot plant consideration. One (Option 1) includes gravity concentration prior to flotation while the other (Option 2) includes finer grinding and four stages of open circuit cleaning. The benefits of each scheme are discussed in detail. Neither has been fully optimised and the definitive flowsheet is most likely to be a hybrid of the two schemes, incorporating the best features of each. Typical metallurgical results from each scheme were final concentrate grades of 49 per cent REO, 10-16 per cent Fe2O3 and 3.2-4.8 per cent CaO. REO recoveries were above 35 per cent in both cases. Features of the processes developed by CSIRO were the inclusion of a gravity concentration stage prior to flotation, a modified flotation reagent scheme, a change in the method of feed preparation, and incorporation of magnetic separation to upgrade final flotation concentrates. Metallurgical results obtained from flotation tests on LI ore were much poorer than those obtained for CZ ore. The best rougher/scavenger result, with the limited amount of testing so far completed, was an REO grade of 32 per cent with a recovery of 28 per cent. Further work is needed to develop a viable processing route for this ore type.

Jan 1, 2000

INDEX OF CONTENTSIntroduction.Systems of classification of coals.RankClassification of Australian coals.Defects of systems in use in other countries.Indexing by Fuel Ratio.Classification by Ultimate Carbon/Ultimate Hydrogen.Relationship between Fuel Ratio and ultimate composition.Suggested convention for classification.Origin and Evolution.Notes on directions of change of composition on Carbon Hydrogen chart.Summary and conclusion.Acknowledgments.Bibliography.Appendix.

Jan 1, 1948

By Juniper LA

ERM Consultants Pty Ltd was established in 1980 for the purpose of introducing a disciplined coal technology and power station planning service, to support Australia's efforts in establishing a major export steaming coal industry. At that time, major coal exploration programs were mounted on more than 50 potential export coal deposits with proven open-cut reserves to export 200 Mt/a of coal. The fact that Australia achieved an export trade of only 30 Mt/a, equivalent to the energy requirements for a population of around 5 million people, illustrates the very small achievement to date. The main reasons for this small export steaming coal growth have been: 1. Failure to convince potential overseas coal buyers of the benefits of coal-fired power generation, and the ability of proper power station design to overcome environmental problems, and achieve reliable operation and long life when burning Australian coals. 2. Failure to promote Australian power engineers to advise on the use of Australian coals, resulting in Northern Hemisphere power station experience dominating in market countries. 3. Failure of governments to draw on privately practising Australian power engineers and coal technologists in technical workshops, presentations and assistance to overseas countries, to ensure that personnel whose business it was to serve the follow-on needs of countries were readily available. The result of these failures has been that: 1. Only a fraction of prospective overseas coal-fired power projects have proceeded. 2. Australia has had no influence in the design of overseas power stations to ensure that potential customers would be confident that Australian coals could be reliably burnt in their boilers.

Jan 1, 1987

By P Walton, L W. Armstrong, D P. Blair

Sydney is the capital city of NSW and has a population of approximately four million people. Eighty per cent of the cityÆs water is supplied by Warragamba Dam, which is situated some 75 kilometres south west of the city centre. A risk assessment was carried out on the dam and future predictions of water flows into the catchment area showed that there was a risk of a one in 700-year flood not being contained by the dam. The predicted loss of life and property damage warranted the construction of an auxiliary spillway on the eastern side of the existing dam to cater for any uncontrollable influx of water. A test blasting program was instigated and the blasting parameters were established that would lead to routine production blasting of the sandstone rock making it more cost effective to excavate. Blast induced vibrations were a concern to the owners and the dam wall and ancillary infrastructure was instrumented with sensitive vibration monitoring equipment during the test blasting phase of the operation. Once the blasting parameters were established from the testing program production blasting was carried out on a daily basis to maintain æstockpileÆ of fragmented ground for the excavation equipment. Blast vibration models were developed to predict vibration levels for more sensitive areas of the dam to give the operators more confidence in their operations. The blast induced vibration levels recorded did not cause any structural damage to the dam wall and the waveform frequencies of the blasting operation were much higher than that experienced during a recent earthquake. The integrity of the SCAÆs assets were at no time jeopardised.

Jan 1, 2001

By C Hertle, B Goebel, R Fabre

The mining industry maintains a ælove-hateÆ relationship with water. Dewatering, aquifer, water disposal, irrigation, process water, tailings water, run-off water, seepage, leachate and sumps are all terms that are used on a daily basis in the mining industry, highlighting the numerous water usages on site and their associated quality. According to the Australian Bureau of Statistics (2001), each year the mining industry consumes over 530 000 ML of water. The increasing recognition of water as a limited and valuable commodity, and the associated environmental concerns with the management of water disposal to the environment has led the industry into improving on-site water management. Progressively, water balance models and water reuse strategies are being developed, incorporating more sophisticated water treatment processes. By way of example, membrane technologies, once restricted to industries such as the pharmaceutical industry or the drinking water industry, are now entering the mining world with the aim of producing clean water of suitable quality for ore processing or for advanced treatment prior to release to the environment. This paper will provide a review of the threats and opportunities linked to water use and recovery/reuse in the mining industry in Australia. It will open with an overview of current water usage and associated quality for various mineral industries and continue with identifying the threats and limitations associated with the quality of available water. It will then present how newly developed water treatment technologies and assessment tools can be incorporated into the system to enhance the recovery and reuse of water on site, reduce the risks associated with securing long-term water supply and further improve production, environment and safety (health risk control).

Jan 1, 2006

By Davies K. E

Several nuclear techniques have been assessed for application to online conveyor belt analysis of oil yield from Rundle oil shale. The most favourable technique is neutron inelastic scattering which determines the total carbon content of bulk shale samples. Correlations of chemical laboratory assays for 540 Rundle oil shale samples show that oil yield can be predicted from total carbon to within 11 litre/tonne.Laboratory experimental work on 17 bulk samples of Rundle oil shale indicated that carbon and oil yield can be determined to within 0.6 wt per cent and 9 litre/tonne, respectively, using the neutron inelastic scatter technique. A practical neutron inelastic scatter gauge for application on a 23 mm thick reinforced conveyor belt could consist of a 5 curie 241 Am-Be neutron source and a 150 mm diameter x 100 mm thick Nal(TI) detector. With this gauge, the analysis time to achieve a counting statistical error of 6 litre/tonne should be about five minutes.

Jan 1, 1985

By R G Warren

Most orebodies have cross-sections of less than 1 km2 and hence do not offer a particularly large target for exploration. Fortunately, although in the geological record ore deposits are small and rare and result from the exceptional coincidence of certain geological processes, these processes are mappable on a much larger, district to regional scale and constitute a mineral system in which the ore deposit is the central feature. A mineral system can therefore be defined as `all geological factors that control the generation and preservation of mineral deposits, and stress the processes that are involved in mobilising ore components from a source, transporting and accumulating them in more concentrated fonn and then preserving them throughout the subsequent geological history'. The mineral system concept emphasises that for many ore deposit types, although economically viable mineralisation may only occur on a scale of say, hundreds of metres, the total system of fluid-rock interactions that led to ore formation can extend over a distance of tens to hundreds of kilometres around the deposit. When mapped out, the total mineral system provides a far larger exploration target than the actual ore deposit itself. Important geological factors defining the characteristics of any mineralising system include: 1. sources of the mineralising fluids and transporting ligands; 2. sources of the metals and other ore components; 3. migration pathway; 4. thermal gradient; 5. energy source; 6. a mechanical and structural focusing mechanism at the trap site; 7. chemical and/or physical traps for ore precipitation. Many of these factors individually are common throughout time and space and are mappable on a regional scale. The delineation and empirical prediction of mineral systems can thus be approached by combining two components of metallogenic research. Firstly, the development of maps of regional geoscientific data and data sets of the distribution of factors significant for mineral systems in general. Secondly, the determination of the essential ingredients of particular styles or types of deposits in terms of mappable elements that any exploration program could focus on.

Jan 1, 1994

By Williams SR

Column Flotation cannot be used indiscriminately. Based on extensive pilot plant experience at Lakefield Research, a number of limiting parameters have been identified for the application of column cell flotation. Parameters of importance are the use of wash water, flotable mineral content, pulp viscosity, type of mineral selectivity being sodght and degree of mineral liberation. The paper discusses when wash water should be used and the positioning of a column within the circuit as this is important to maintain a sound water balance for the circuit and prevent excessive circulating loads. Other areas of debate are pulp chemistry, very low and high weight recovery, for which the conventional column is a poor selection of equipment, and treatment of complex ores, where the separation of valuable minerals is more difficult than non-sulphide, sulphide mineral separation. Based on these observations, the application of column flotation must be carefully considered or can be optimised.

Jan 1, 1993

By Hall S. F, Quast K. B Newell R, Ketteridge I. B

For the past six years research funded by the State Energy Research Advisory Commit- tee of South Australia has been conducted at the South Australian Institute of Technology, School of Mining and Metallurgy on South Australian lignites. A major part of this work has been a study of the potential bene- fication of Bowmans lignite using hydrometal- lurgical techniques. The Bowmans lignite de- posit is the largest of its type in South Australia and is a major energy reserve for the state. The utilization potential of this deposit is reduced by its very high insitu NaCl content which presents serious problems for any process. Previous research conducted by Readett and co-workers (1984a & b) has shown that NaCl is amenable to extraction using simple batch water leaching operations. This leaching has been successfully described using a two stage diffusion model derived from first principles based on a simple diaphragm cell.

Jan 1, 1987

By Weller K. R, Trahar W. J

The Mount Lyell Company treats some 2.3 million tonnes of ore annually, mined from a number of orebodies on the field. Blended ore is essentially a quartz-sericite schist containing about eight per cent of pyrite and three per cent of chalcopyrite. Four-stage crushing and two-stage ball milling are followe by selective flotation for copper. Pyrite is recovered from the coarse fraction of dopper circuit tailings. A detailed survey involving examination. of 82 samples provided information on the size- by-size behaviour of the principal ore constituents throughout the grinding, copper flotation and pyrite flotation sections of the circuit. Results for the copper and pyrite flotation sections are presented in the paper, and it is shown that over half the copper reporting to the final tailing (5% of copper in the feed) is plus 100 microns and that the major pyrite loss is in the desliming cyclone overflow. These data proVide a basis for assessing potential methods of circuit optimisation.

Jan 1, 1977

By E Drueppel, M Mistry, J Pateiro

As mining undoubtedly influences the natural environment future challenges of copper ore mining are minimisation of land use in area and duration, proper land rehabilitation as well as tailings management. One possible solution to avoid these negative impacts could be the application of underground mining with backfilling tailings compounds. This approach would definitely increase the production cost. Against this background the project analyses the influence of an æecologically satisfyingÆ copper ore mining on world market prize and demand as well as on the environment. In the project 261 copper ore mines accounting for 98 per cent of world copper production have been examined. After modelling a backfill plant, analyses of applied backfill techniques were conducted. Afterwards a method of cost estimation was developed and then the backfill plant model was applied in three case studies. The results were transferred into scenarios. The work closes with a short discussion and gives an outlook to forthcoming research. The results presented in this work have been generated within the Collaborative Research Center (CRC) 525 entitled æResource-orientated view of metallic raw material flowsÆ. This interdisciplinary project was established at Aachen University of Technology (Germany) in 1997 and is funded by the Deutsche Forschungsgemeinschaft (DFG). The long-term goal of this research program is the identification of options for the resource-sensitive supply and processing of metallic raw materials. In order to address the sustainable development challenges facing the metals and minerals industry an integrated resource management system is to be developed and tested for important metallic raw materials. Case studies for aluminium and copper are being conducted by the CRC 525 in order to provide useful and efficient tools for decision makers over the entire life cycle of these materials.

Jan 1, 2003