Search Documents

By B S. S Rao, S Chandra

IndiaÆs iron ore mining industry is growing rapidly in order to augment the capacity to meet the unprecedented demand for the iron ore. Traditionally, much of Indian iron ore production came from exploitation of high-grade haematite ores, with the exception of Kudremukh which beneficiates lean grade Banded Magnetite Quartz ore. Now with the changed scenario of demand and supply, keeping long term sustainability in mind, it is imperative to develop suitable processing technology for exploitation of banded haematite quartz (BHQ) ore available abundantly and not utilised so far. In this direction detailed characterisation and beneficiation studies were conducted with BHQ iron ore from the Bellary-Hospet region of India, assaying 36.5 per cent Fe. The mineralogical studies with the image analyser system revealed the presence of maghemite and haematite as iron-bearing minerals. The gangue mineral associations were siliceous, ferro-magnesian and carbonate minerals. Higher degrees of liberation were observed in the size range of 75 - 212 microns. Liberation grind tests were performed by grinding the ore to different top sizes in a closed circuit laboratory ball mill with the ground samples subjected to Davis tube tests. The yield, grade and recovery were used as parameters to plan a two-stage wet drum magnetic separation based on grinding the primary magnetic concentrate. After subjecting the final magnetic concentrate to flotation to remove residual silica a concentrate assaying more than 68 per cent was obtained. The non-magnetic product from the primary magnetic separation was deslimed, ground, blended with secondary magnetic tails and was subjected to a two pass wet high intensity magnetic separation (WHIMS). The WHIMS concentrate was further subjected to two-stage flotation to remove residual silica to obtain concentrates assaying 64 - 66 per cent Fe. The final combined concentrate from wet drum magnet and WHIMS after flotation could yield a blast furnace (BF) grade pellet feed concentrate assaying more than 65 per cent Fe with a yield about 39 per cent and iron recovery about 70 per cent. A direct reduction (DR) grade pellet feed concentrate assaying 67 per cent Fe with a yield of about 28 - 31 per cent and iron recovery about 53 - 57 per cent could also be produced. Based on the test work, a process flow sheet was developed to beneficiate the BHQ ore for production of BF/DR grade pellet feed concentrate. In this paper methodology adopted for selection of individual process, various diagnostic tests performed to rule out other beneficiation processes and the final process flow sheet development is presented and discussed in detail.

Jan 1, 2007

Water is important commodity in the mining industry. Water is used in the many stages of mining from the exploration stages and drilling, to mine development and operation and finally throughout mine rehabilitation and post mine activities. With the use of water throughout the life span of a mine, its management is an important component in the operation of any mine. Unfortunately the use of water within the operations can be one of the major sources of pollution generated from a mine. Such contamination can occur via numerous mechanisms including ground water flow, over land flow and accidents. Contamination may occur in any stage of mining operations, for example a leaking or failed tailings dam. With the above in mind, the paper presented will focus upon the use and management of water in the mining industry: ownership rights of water û common law as well as legislative rights; a review and analysis of the existing Queensland legislation and its mechanisms for the protection of water pollution from mining operations; and conclusions drawn from the paper relating to the Queensland legislation.

Jan 1, 2003

The phrase "Total-Energy" has, during the past few years, become widely used to describe a wide range of very different operations. However, if accurately described they all have one basic factor in common - energy usage is optimised with the prime mover being powered by gas or oil to generate shaft horsepower and the products of combustion being put to some use. The item which distinguishes a Total Energy system from any other engine or turbine driven project is that orate pains are taken to utilize the waste heat, whether this be in the form of exhaust gases and/or engine jacket ling water. n areas where grid supplies of electricity are readily available, the economics of most projects undoubtedly hinge upon the successful application of waste heat. However, there has been a growing awareness of other benefits, such as reliability of supply, which can be incorporated into the system. In particular these factors sway managements of hospitals and companies with complex computer facilities to examine closely the feasibility of Total Energy, Consequently, in America for example, where many systems have proved themselves the list of applications is wide - shopping centres, apartment blocks, office buildings, airline terminals, universities, schools, motels. And these do not cover the industrial sectors where the range is wider. The total number in North America is now approximately 500 and this to some extent-speaks for itself. In Australia, the real work involved in carrying out feasibility studies for Total Energy is only just beginning. 'in some quarters, the concept is not well received in that it is too new. Therefore, a typical approach is to play safe and wait until some other company has proved its operation "under Australian conditions". This is certainly a realistic approach when considering something revolutionary but as far as Total Energy.is"concerned all the individual components and sometimes combinations, (engines, generators, boilers, air-conditioning units) have been in operation for many years. The only innovation is that they are now all being brought together under one roof. This should not be forgotten when the question "where can I see something like this operating?" is asked.

Jan 1, 1970

The phrase "Total-Energy" has, during the past few years, become widely used to describe a wide range of very different operations. However, if accurately described they all have one basic factor in common - energy usage is optimised with the prime mover being powered by gas or oil to generate shaft horsepower and the products of combustion being put to some use. The item which distinguishes a Total Energy system from any other engine or turbine driven project is that orate pains are taken to utilize the waste heat, whether this be in the form of exhaust gases and/or engine jacket ling water. n areas where grid supplies of electricity are readily available, the economics of most projects undoubtedly hinge upon the successful application of waste heat. However, there has been a growing awareness of other benefits, such as reliability of supply, which can be incorporated into the system. In particular these factors sway managements of hospitals and companies with complex computer facilities to examine closely the feasibility of Total Energy, Consequently, in America for example, where many systems have proved themselves the list of applications is wide - shopping centres, apartment blocks, office buildings, airline terminals, universities, schools, motels. And these do not cover the industrial sectors where the range is wider. The total number in North America is now approximately 500 and this to some extent-speaks for itself. In Australia, the real work involved in carrying out feasibility studies for Total Energy is only just beginning. 'in some quarters, the concept is not well received in that it is too new. Therefore, a typical approach is to play safe and wait until some other company has proved its operation "under Australian conditions". This is certainly a realistic approach when considering something revolutionary but as far as Total Energy.is"concerned all the individual components and sometimes combinations, (engines, generators, boilers, air-conditioning units) have been in operation for many years. The only innovation is that they are now all being brought together under one roof. This should not be forgotten when the question "where can I see something like this operating?" is asked.

Jan 1, 1970

Commissioning is one of the many phases of a project, it has inter-dependencies with the other phases, as they have amongst themselves, and has its own terminology and distinctive features. Commissioning time and cost can severely affect project economics, especially through unrealistic estimating, and requires a separate management team to ensure full control is. maintained. Targets to be achieved in commissioning are identified, together with the necessary policies to achieve them. Factors which have to be taken into account in applying these policies are Discussed.

Jan 1, 1986

By D E. Ralph, D-J Kim, G-J Ahn, Y-H Rhee

The amount of discarded dry batteries are presently found to be increasing globally and waste cathode active materials of the lithium ion battery industry are among them. Hydrometallurgical operations are being applied to recover the valuable metals from these waste batteries. To find an economic and environmentally friendly process, the bioleaching process was applied in the present investigation for recovery of valuable metals. Its principle is the microbial production of sulfuric acid and simultaneous leaching of metals. Bioleaching of spent lithium ion secondary batteries, containing LiCoO2, has been studied in this investigation. A new method for recovery of cobalt, potentially the basis of an economic and environmentally friendly process was examined. The present study has been carried out using chemolithotrophic and acidophilic bacteria Acidithiobacillus ferrooxidans, which utilises elemental sulfur and ferrous ion as the energy source to dissolve metals from spent batteries. Bio-dissolution of cobalt was found to be faster than lithium. The effect of initial Fe(II) concentration, initial pH and solid/liquid (w/v) ratio were studied in detail. Higher Fe(II) concentration showed a decrease in dissolution due to co-precipitation of Fe(III) with the metals in the residues. Similarly, at higher initial pH values and higher solid/liquid ratio (w/v) metal dissolution was found to be inhibited. The optimised conditions for bio-dissolution were solid/liquid (w/v) ratio û 10 g/L, initial Fe(II) concentration û 3 g/L, elemental sulfur û one per cent (w/v) and initial pH û 2.5. In the optimised conditions, cobalt dissolution was observed to be about 60 per cent, whereas that of lithium was ten per cent after 20 days. A first order kinetic model was derived to study the rate of dissolution of both the metals.

Jan 1, 2006

IA )W cli',hla cn1cnt fault 7011(-s 0 11Cn cOrnprise a nrc,II of inrcIIinkc(I faults, cvtcnqonal shear and In]rck cxtcnsir>nal vein- fractures. Hydrothermal mineralisation localised around such structures testifies to their importance as conduits for fluid flow. Mesh structures are most commonly developed in situations approximating bulk pure shear but predominantly simple shear meshes also occur. They appear to develop through the infiltration of pressurised fluids into a heterogeneous rock mass with varying material properties. In some circumstances, mesh formation appears to be a precursor to the development of major throughgoing faults. Mesh formation generally involves hydrofracturing (Pf> a3, at least locally) and the condition Pf - 63 to be maintained for the mesh to remain a high permeability conduit, requiring fluid overpressuring at other than shallow depths in extensional-transtensional regimes. The volumetric character of earthquake swarm activity appears to result from the passage of hydrothermal fluids through mesh structures, representing a form of distributed fault-valve action along suprahydrostatic hydraulic gradients arising from magmatic intrusion, compaction overpressuring, metamorphic dewatering, etc.

Jan 1, 1995

By S Sabanov

Supplementary sampling of particulate mass concentration, the number concentration and the average particle diameter of nanoparticles using a TSI Dust-Trak DRX Aerosol Monitor, Naneos Partector 2 has been conducted. The aim of this study was to evaluate suitability of the instrument for long-term monitoring of diesel particulate matter (DPM) at conditions of polymetallic mines. Sampling was conducted in an area of the active ore heading, requiring the use of a diesel-powered face haul-age loader R1700 and a mine truck Caterpillar AD-45. The sampling was done for 126 minutes at a distance of 30 metres from the mine face. Results of this field work can be used to expand the sampling program to other mines. Expected outcomes of this study are to develop costeffective DPM control strategies, improve mine ventilation, and protect mineworkers’ health.

Oct 12, 2022

The process of resource estimation of large precious metal deposits is illustrated by reference to major deposits now being mined or developed by Placer.The estimation procedure commences with building an appropriate model of the mineralization and proceeds through steps of data validation and geostatistical studies. It is important that the geologists most familiar with a deposit be involved with all stages of the estimate, and also prepare a manual estimate used to validate the kriged resource.Resource estimates are major exercises taking many man-months of work. The most time consuming part of this is usually construction of an appropriate three dimensional geological model. The data base for the resource calculations must be complete and checked for accuracy. The most appropriate estimation method must be selected.

Jan 1, 1990

By L Grigorov, G J. Jame, A V. Nguyen

The dewetting kinetics between a small air-liquid interface and a silica (negatively charged in water) planar surface in solutions of dodecylammonium chloride (cationic surfactant) has been investigated using the Scheludko cell and digital high-speed video microscopy. The gas-liquid interface was created at the bottom of a small silica capillary of the cell and then was moved towards the silica planar surface. After the rupture of the liquid films between the interfaces, the expansion of the gas-liquid-solid three-phase contact (TPC) line was observed and recorded using a digital high-speed video microscope system, operating at 1000 frames per second. The surface tension of the surfactant solution was measured using the pendant drop technique. The equilibrium contact angle was measured using the Scheludko-Minings method with a silica micro-sphere. The TPC radius was determined as a function of time and compared against the available hydrodynamic and molecular-kinetic models. The experimental data are described very well by the molecular-kinetic model for the TPC line motion. The hydrodynamic model is in agreement with the experimental data only for a short time after inception of the three-phase contact expansion.

Jan 1, 2005

By Morris P. H

A trial embankment was constructed using coarse coal mine reject on a deposit of crusted coal mine tailings at New Hope Colliery, located in the Bundamba District of the West Moreton Coalfields in South East Queensland, Australia. The purpose of the trial embankment was to assess the load carrying capacity and settlement behaviour of the crusted tailings, including an assessment of strength gain in the tailings under the influence of the fill. Prior to construction of the trial embankment, a site investigation of the tailings deposit was carried out. This comprised vane shear strength testing, together with disturbed sampling and undisturbed block sampling for the purposes of laboratory testing. Following the site investigation, settlement plates and standpipes were installed at various depths and locations within the tailings in the vicinity of the proposed embankment. The instrumentation enabled the magnitudes and distributions of settlement and pore pressure within the tailings to be determined during and following construction of the embankment. The embankment was constructed using coarse reject in three equal lifts to a height of 3.0 m. The tailings sustained a maximum settlement under the weight of the fill of 290 mm, representing about 4.2 ii of the average initial thickness of the tailings and a loss of embankment height of about 9.7 %. By the end of the monitoring period the strength of the softer tailings underlying therust had roughly doubled under the influence of tha cmbarikment

Jan 1, 1990

The Savage River open cut magnetite mine is located in rugged terrain in densely rain forested northwest Tasmania. The mine and concentrating plant are both in the Savage River valley. Pickand Mather Incorporated (PMI) operated Savage River as an open cut magnetite mine between 1966 and 1996. Acid rock drainage (ARD) was first noted in the last ten years of the operation, leading to elevated concentrations of heavy metals downstream of the mine. When operations ceased in 1996, PMI returned the mine to the Tasmanian Government along with a remediation fund of $11.4 million. At that time, the assessed cost of remediation was in excess of $120 million. As a result of the ongoing ARD contamination and to facilitate both a new operation and effective remediation, Goldamere Pty Ltd negotiated an agreement with the Tasmanian Government in 1996, which resulted in the Goldamere Act and the Goldamere Agreement. The agreement has allowed Australian Bulk Minerals (ABM) to remediate the Savage River mine in conjunction with the Tasmanian Government while re-invigorating a previously closed mine by providing ABM with an indemnity against past pollution. ABM can configure its mine and waste planning activities to maximise remediation benefits without fear of future litigation for past mistakes. The effect to date has been the development of a long-term strategy to remediate the Savage River and short-term remediation works such as water management, which provide benefits to the ecosystem. After five years, the Savage River is no longer significantly impacted by ARD for 30 kilometres downstream and trout are now reported within the reaches of the mining lease. The arrangements between ABM and the Tasmanian Government are an example of a genuine WIN WIN situation where co-operative environmental management of the site results in significant improvements and where the æregulatorÆ and the æminerÆ are working together to achieve mutually beneficial goals. The end result is a significant benefit to Tasmania.

Jan 1, 2003

By F Minz, P Lamberg, A Mwanga, C Lund, C Wanhainen, M Amiri Parian, J Rosenkranz

A geometallurgical model is currently built in two different ways. The first and the most common way relies on geometallurgical testing, where a large number of samples are analysed for metallurgical response using small-scale laboratory tests, eg Davis tube testing. The second, mineralogical approach focuses on collecting mineralogical information over the orebody and building the metallurgical model based on mineralogy. At Lules University of Technology, Sweden, the latter method has been adopted and taken further in four ongoing PhD studies. The geological model gives modal composition by the help of element-to-mineral conversion and Rietveld X-ray diffraction. Texturally, the orebody is divided into different archetypes, and liberation measurements for each of them are carried out in processing fineness using IncaMineral, a SEM-based technique. The grindability and liberation spectrum of any given geological unit (sample, ore block, domain) are extrapolated from the archetypes. The process model is taken into a liberation level by mass balancing selected metallurgical tests using the particle tracking technique. The approach is general and can be applied to any type of ores. Examples of ongoing studies on iron and massive sulfide ores are given.CITATION:Lamberg, P, Rosenkranz, J, Wanhainen, C, Lund, C, Minz, F, Mwanga, A and Amiri Parian, M, 2013. Building a geometallurgical model in iron ores using a mineralogical approach with liberation data, in Proceedings The Second AusIMM International Geometallurgy Conference (GeoMet) 2013 , pp 317-324 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 29, 2013

By Davies S. G, Jayaweera A

The oxidation of nickel sulphide and copper sulphide concentrates, and coal, has been studied under non-ignition and ignition conditions using Differential Thermal Analysis (DTA) and Thermogravimetry (TG). The non-ignition reaction was favoured by slow heating rates < 10°C min-1), low masses < 10 mg) and an air atmosphere. Under these conditions, the typical stepwise oxidations of the various sulphide minerals present in the concentrate were observed as resolved exothermic peaks in the DTA curves and weight losses in the TG curves. Above a heating rate of 10°C min-1 , sample masses in excess of 10 mg and an oxygen atmosphere, an ignition reaction was induced, as indicated by a major high energy exotherm in the DTA curve and a major rapid weight loss in the TG curve. The ignition temperatures of the minerals under ignition conditions, found for 15 mg samples heated at 20°C min-1, were 434°C for the nickel sulphide concentrate, 372°C for the copper sulphide concentrate, and 230°C for the coal. By plotting a curve for mass against ignition temperature at constant heating rate and extrapolationto zero mass, a value of 470°C was obtained for the mass independent ignition temperature of the nickel sulphide concentrate. Ignition temperatures and extents of reaction at various temperatures were obtained using the TG technique in a novel manner which produced heating rates of 4500°C min-1. Under ignition conditions, the oxidations approximate to flash smelting conditions.

Jan 1, 1985

By G A. Streltsova

In the paper the main concept of qualitative simulation is determined when computer-aided designing and forecasting of designs of robotised continuous-flow working face complexes for underground mining of hard ores. The parametric model æunderground ore mineÆ and its components û composite models are considered. Frame description of structure of working face complex and methods of organising of rule-oriented representation of knowledge when itÆs operating are given. The architecture of the developed prototype of expert system æworking face complexÆ and construction of a knowledge base for it are described when solving problems of multi-criteria optimisation of computational parameters of the working face complex under conditions of uncertainty. The guidelines for further development of knowledge base and expert system are given.

Jan 1, 2003

George Fisher Mine, near Mount Isa in northwest Queensland, has been producing Pb-Zn-Ag ore since the late 1980s. It consists of two separate underground deposits, George Fisher South and George Fisher North. These two deposits are drilled and modelled separately but are crushed and hoisted as a single stream. The Pb-Zn concentrator in Mount Isa processes ore from George Fisher Mine and Black Star Open Cut, with production also from the Isa Lead Mine until January 2006. This paper outlines the steps involved in setting up a robust reconciliation system for George Fisher Mine, in conjunction with requirements of the Pb-Zn concentrator, Black Star Open Cut Mine and the Mount Isa Lead Mine. Good quality input data and commitment to training have contributed to establishing a robust and effective reconciliation system. Reconciliation data has highlighted several other continuous improvement opportunities.

Jan 1, 2006

In the last 100 years, statistical sampling theory for particulate materials has developed to a stage where sampling systems can be confidently designed to provide assay results of known and controlled variance for a chosen time period. The two independent sources of sampling variance, namely intrinsic and distributional heterogeneity are defined and explained quantitatively. Intrinsic heterogeneity is characterised by the sampling constant for the material and distributional heterogeneity is quantified by the process steam variogram or covariance function. The means by which sampling systems can be designed to an accuracy specification is described.

Jan 1, 2002

By J Brown, C Roberts

The scope of this paper is to recount the development of segmental linings used in tunnel construction, starting with its inception as an improvement to the brick-lined tunnel approach of Brunel in England and moving through the history and development to the present day, before finishing with a few insights into what the future might hold. The paper also discusses the motivation for the relatively recent move towards replacing conventional steel reinforcing cages with steel fibres and the reasons why steel fibre reinforced concrete (SFRC) is rapidly becoming the material of choice for manufacturing precast concrete segmental linings.

Jan 1, 2008

By Mountiney B

The development and operation of three large open cut brown coal mines in the Latrobe Valley, Victoria, Australia, requires a wide range of drilling techniques for coal resource evaluation and stratigraphic defi- nition, material property identification, open cut dewatering, and instal- lation of groundwater monitoring bores. This paper describes in detail the range of drilling techniques, equip- ment used and associated problems with drilling, in a deep sedimentary basin containing several major brown coal seams, multiple aquifer sys- tems of varying pressures and thin layers of hard materials including pyrite, siderite and basalt. Methods of rotary drilling include wireline core drilling, conventional core drilling, conventional flush drilling, diamond core drilling, reverse circulation air lift drilling and bucket auger drilling. Cable tool drilling is also used for strata definition and aquifer sampling.

Jan 1, 1989

By B B. Beamish, M S. Kizil

The processes that take place during the development of a heating are difficult to visualise. Bulk coal self-heating tests at The University of Queensland (UQ) using a two-metre column are providing graphic evidence of the stages that occur during a heating. Data obtained from these tests, both temperature and corresponding off-gas evolution can be transformed into what is effectively a video-replay of the heating event. This is achieved by loading both sets of data into a newly developed animation package called Hotspot. The resulting animation is ideal for spontaneous combustion training purposes as the viewer can readily identify the different hot spot stages and corresponding off-gas signatures. Colour coding of the coal temperature, as the hot spot forms, highlights its location in the coal pile and shows its ability to migrate upwind. An added benefit of the package is that once a mine has been tested in the UQ two-metre column, there is a permanent record of that particular coals performance for mine personnel to view.

Jan 1, 2005