Search Documents

By K Nakashima, K Aya, T Sumita, N Saito

Electro slag remelting (ESR) is one of the methods used to produce high-cleanliness steel. In the ESR method, the product steel electrode is immersed in flux, and the electrode is melted by the Joule heat of the flux generated by high current. CaF2-based melts are mainly used as fluxes, but the electrical conductivity of CaF2-based melts varies widely among researchers and measurement methods. Therefore, this experiment aims to measure the electrical conductivity of CaF2-based melts based on the van der Pauw-Ohta method, which does not require the cell constant that is a fundamental error factor in electrical conductivity measurement at high temperatures. The measurement temperature was set at 1450–1600°C, and dehydrated Ar flowed through the furnace at 200 mL/min. Electrodes were fabricated by Pt-30mass per cent Rh alloy, and the electrodes were connected to an impedance analyser using a four-terminal probe. The electrodes were immersed in the melt, and the impedance and phase angle were measured by AC frequency sweep (50 Hz to 200 kHz). The electrical conductivity was then calculated by utilising the impedance’s real part values when the impedance’s imaginary component was zero. The electrical conductivity showed a positive temperature dependence. The electrical conductivity of 60(CaO⋅Al2O3)-40CaF2 melt increased with increasing temperature but was found to be roughly one-third of those of the previous studies. In the conductivity measurement of 60(CaO⋅Al2O3)-40CaF2 melt, the AC frequency with a phase angle of 0° was found to be different depending on the temperature and immersion depth. By sweeping the frequency, the impedance at the phase angle of 0° can be obtained, which enables us to measure the electrical conductivity more accurately.

Jun 19, 2024

By Komosa T, Muir D. M

Adequate levels of dissolved oxygen are essential for efficient gold dissolu- tion. The actual levels in plantpuips can be seriously reduced by the presence of oxygen consuming reactive minerals, and reduced oxygen solubility in saline water. The rate of gold dissolution is then limited by oxygen availability rather than cyanide. Ion selective electrode dissolved oxygen meters can give an effective indication of the relative oxygen saturation, but they are not able to give meaningful values of dissolved oxygen in saline water, without custom calibration curves. When the dissolved oxygen concentration is rate limiting, the addition of oxygen or peroxide can improve gold leaching kinetics as well as reduce cyanide consumption.

Jan 1, 1991

By Hosking IA, Mirkov P

Among the solutions currently being considered for improving traffic flow in Sydney are the construction of major road tunnels, principally the Eastern Distributor Tunnels, leading from the end of the Cahill Expressway to Drivers Triangle and South of Taylor Square and the Sydney Harbour Tunnel, which incorporates sections of driven tunnel at the northern and southern sides of the harbour. The Eastern Distributor Tunnels, known as Stages 2 and 3 of the Eastern Distributor Scheme comprise: Stage 2 - A south bound two lane tunnel from north of William Street to Driver's Triangle. The southern end includes two Y junctions (locally 3 to 4 lane widths) with exits into South Dowling Street, Anzac Parade and Moore Park Road. Stage 3 - A north bound, two lane tunnel from Taylor Square to Palmer Street just north of William Street. Further details of the Eastern Distributor Tunnels are given in the paper by Baxter, Chappel and Fishburn (1986) which is included in this conference.

Jan 1, 1987

By Inoue T, Takahashi N

To construct the accessing railroad line to the northern portal of Seikan Undersea Tunnel, nine tunnels amounting 7.4km in their total length were excavated through soft mudstones of young- er tertiary era with use of smaller-sized mechanic al excavators. Rocks were classified in four classes to which the tunnel support was designed respectively. Of several combinations of driving equipments stu- died comparatively, the method using the mechani- cal excavators was estimated to be the best choi- ce. The efficiency of the excavator was traced in every construction section and the data colle- cted was reviewed numerically. The result showed that the efficiency of the excavator dropped wh- ere the rocks were as hard as over 200kg/crif for compressive strength. And a few technigues in tunnelling i.e. contr- olling dusts in shotcreting, lattice arch, evaluati- ng measured deformations were tested and review- ed too.

Jan 1, 1987

By B Sno, P A. Cockburn, R C. West, C U. Jones

Clyde Materials Handling (CMH) and WorleyParsons have developed a concept for a flash furnace feed system using the specialist pneumatic conveying equipment expertise of CMH and the flash furnace process experience of WorleyParsons. CMH has developed a proprietary volumetric feeder (called a Rotofeed), which is extremely accurate and overcomes many of the problems inherent with loss-in-weight screw feeders and drag chain conveyors, previously regarded as state-of-the-art. Initial indications are that the Clyde-WorleyParsons feed system could deliver the following benefits to flash furnace operation: accurate pulseless delivery of feed material to the head of the burner leading to improved combustion performance and process stability; highly accurate split to the individual quadrants of a conventional burner tube, or provision of a smooth hollow curtain to a burner without guide vanes; decreased pressure pulsation in the furnace due to improved combustion control and performance; and decreased temperature fluctuations in the furnace due to improved combustion characteristics and hence reductions in refractory thermal stress and wear.

Jan 1, 2005

By C J. Stanley

Reflected light optical microscopy, or epimicroscopy, is one of the oldest techniques of modern mineralogy. At a relatively low capital cost, it is also very resourceful, and the analytical choice for the identification of most ore minerals. In ore mineralogy, reflected light optical images have the potential to overcome the main limitation of backscattered electron images from scanning electron microscopes, namely contrast of mean atomic number  below the spectral resolution of the backscattered electrons detector. This is the case for relevant ores, like iron (haematite-magnetite) and copper-zinc ores (sphalerite-bornite), but for both cases the pairs of minerals are easily discriminated in reflected light. The improvements in optics and electronics also made microscopy a powerful source of digital images, suitable for automated analysis for minerals processing, as the determination of liberation spectra. The drawback, however, has always been the impossibility to recognise the transparent minerals, which account for most of the gangue phases in ores, from the embedding resin, usually epoxy. In order to determine if there was any possibility to separate quartz from epoxy resins, reflectance spectra have been acquired for quartz and some commercial epoxy resins (Araldite, BuehlerÆs Epothin and Epocolor, Araldite spiked with fluorochrome from Struers), from 380 to 720 nm in 5 nm intervals. Reflectance of quartz and epoxy is very similar over the whole visible light range, and varies from 4.5 to five per cent. Epocolor, a red-dyed epoxy, reflects slightly more above 560 nm, as does Araldite spiked with the fluorochrome from 460 to 570, but for both the reflectance is still very close to that of quartz, under 5.1 per cent. This data set is final, and precludes the application of reflectance in light optical image analysis for assessment of liberation, phase quantification, or any other signal that requires separation of resin from transparent minerals.

Jan 1, 2008

The complete life cycle of a production facility has many phases requiring many different skills and many different personalities. It is not unlike the life cycle of a person and many parallels can be drawn from it. I leave some of these analogous situations to your fertile minds. The author, having worked in operations, plant design, plant commissioning, marketing and many other interesting situations through the industry has drawn from this experience and examples given by many associates in the industry.The phases seen are as follows: Concept Studies û someone has a bright idea of how to make a dollar. Scope Studies û what possible processes/options that could make a dollar. Prefeasibility Study û the æviableÆ scope options are studied to develop feasible options. Feasibility study û defines the concepts that should be designed to make a viable project thus enabling financing and project commitment to be made. Detailed Design û an intermediate step that consolidates the inputs to give a robust plant that can be constructed.Construction û people can see what they thought was going to occur and start to understand the plant. Commissioning û the hand-over of æownershipÆ from the conceiverÆs to the operators. Operations û the ætoyÆ has become reality and money must be made. De-commissioning û the plant has seen out the useful life of the ore deposit, it now goes through a further process required by society.Across these phases of plant design run several countervailing management requirements that can influence the outcome of the plant design. Some of the management rigours that have to be applied to the various phases are as follows: costing basis of the various phases; operational and maintenance reviews; sustainable development; risk assessment; reliability reviews; equipment availability; commissioning time; and environmental review.This paper endeavours to awaken people to the phases that projects require for a successful outcome and the management rigour that has to be applied throughout the phases to ensure the correct intellectual horsepower is applied at the right time to ensure the best outcome.Many of you would be parents and realise this is not unlike the development of children, teenagers, adults, retirees and ongoing.

Jan 1, 2002

Multiple regression analysis applied to ventilation records of stopes on the Witwatersrand showed that it was possible to estimate the temperature increase per 100 ft for a new stope with a standard deviation of 0' 5°F. The analysis also threw light on the relative effect on this estimate of five different factors.Application of the analysis of variance technique to a factorialexperiment on the production of dust during rock drilling showed that the effects of air and water pressure were quite small but also showed that the between-machine variation was unexpectedly large.Analysis of variance also proved a valuable means for assessing the bias and random error variation of aneroid barometers used in pressure surveys.INTRODUCTIONThree examples are discussed to illustrate the use of the techniques of "analysis of variance" and "multiple regression" in research on the ventilation of gold mines. Although the techniques are basically similar their application to each example has a slightly different emphasis and the examples were chosen for this reason. The variation ofemphasis is as follows.1. Temperature increases in stapes. This work was undertaken as a preliminary to possible extensive controlled experimentation (Lambrechts, 1959). Data collected in routine work by the mine ventilation personnel were used for analysis and no specific experiments were carried out. The main object was to see whether such data could provide any strong pointers to factors which might be worthy ofmore careful study and to factors which could initially be ignored. Of course, there was hope that the study might provide an empirical formula for rough forecasts.

Jan 1, 1962

An established method exists for the computation of rope lifetimes for shaft hoisting applications in the mining industry. In an earlier study, during the 1990s, an initial comparison of the calculated and actual rope life for various types of hoisting plants showed reasonably good correlation. In the meantime the calculation method has been developed further. The rotation behaviour of the rope during hoisting and the effects of multilayer spooling on drums are now considered in the assessment of expected rope lifetimes. The ability to determine an estimate of rope life in advance is particularly useful for mining companies. Such analysis allows them to predict the effects of rope choice in their particular application and thereby reduce the total cost of rope ownership. Such calculation techniques also allow designers of winding plants to identify aspects of the hoisting configuration that may negatively affect rope life. Often small (low-cost) changes, like increasing the diameter of head sheaves, can result in considerable improvements in rope performance. This paper describes the extended lifetime calculation method and gives further examples of the comparison between actual and calculated rope lives for operational double-drum mine hoists.

Jan 1, 2005

By Frost M. T

Magnesium is the lightest metal used in structural applications but these are only a small part of magnesium usage, with the use in aluminium alloys consuming half the magnesium produced. Other applications include steel desulphurisation, nodular iron manufacture and metal reduction. Demand for magnesium is expected to increase towards the end of the decade because of a requirement to lighten the weight of automobiles. The current western world plant capacity and production rate is 250 000 tpa. The CIS and PRC also have production capacity but shipments from these countries have been limited in the last half of 1994. The price for magnesium has followed trends similar to aluminium with recent recovery from US$1500 per tonne in 1992 and 1993 to US$4000 per tonne in 1995. The major magnesium producers all use different production methods and the potential exists to establish a large-scale magnesium industry with operating and capital costs comparable to aluminium. The Australian Magnesium Research and Development Project has been established to develop a low cost method of production using the magnesite and infrastructure resources in Central Queensland.

Jan 1, 1995

Stope control information at the C.S.A. mine is obtained by diamond drilling inclined holes from within the stapes. Practical mining outlines are determined from complicated ore contours by a joint mining engineering and geological study. Production holes to achieve this outline are individually marked up and checked. Stope control also extends to selective mucking of ore mixtures for metallurgical reasons and to marginal ore and waste mixtures for economic reasons.

Jan 1, 1969

By Fletcher G

This paper will outline the design process, and the constmction and rehabilitation techniques proposed for the external waste dumps associated with the mining of the Wolfang Basin coal measures.The basin is located to the north of Clermont and immediately west of the Bowen Basin in Central Queensland, Australia. Development of the Clermont Coal Mine is planned for the mid-1990s after adequate sales commitments are obtained to allow the project to proceed.

Jan 1, 1992

By Shibata Y, Shimizu R, Fukushima A

Kobe is divided by the Rokko Mountains, runn- ing from east to west. The southern section of Kobe is highly developed in contrast with the northern section, but big, new residential pro- jects like the Hokusetsu New Town and Hokushin New Town are steadily being developed. To handle future traffic between the two sections of the city, the double-tracked Hokushin Line, now under construction, will connect the Shin Kobe Station of the Kobe Municipal Transit (Kobe's subway system) to the Tanigami Station of the Kobe Electric Railway. The locations of Kobe city and Hokushin Line are shown in Fig.-1 and Fig.-2 respectively.

Jan 1, 1987

Asbestos is a commercial term applied to fibrous varieties of several minerals, the properties of which are not generally appreciated by the majority of geologists. A thorough knowledge of these properties and of the uses of asbestos is of fundamental importance in the assessment of the economic value of an occurrence of asbestos. The varieties of asbestos that are used predominantly by the manufact- urers of asbestos products are chrysotile, crocidolite and amosite but chrysotile constitutes 95% of the world's usage. It is the properties of high tensile strength, 'heat resistance and large surface area that make chrysotile asbestos the most acceptable of the mineral fibres. There are no known exploration aids, other than direct visual inspec- tion of outcrops in ultrabasic environments, that could be used in the exploration of chrysotile asbestos. The surface exploration of an occurrence of chrysotile asbestos is relatively routine, though it lends itself to a unique form of bulk sampling by the use of a twelve inch diameter diamond drill core. The laboratory assessment of the prop- erties of the actual fibre requires specialized techniques and tests to assess not only the amount of fibre present but also its length distri- bution, inherent strength, filterability, dust content and other prop- erties. The way a fibre reacts to milling will determine what milling process- es must be implemented to ensure a product that is acceptable to the asbestos product manufacturing industry.

Jan 1, 1971

Mine dewatering has long been a problem with mines and some of the shallowest mines have the biggest problems. Machinery was developed by the ancients for raising water by rope buckets with treadmills or by horse whim. From the 1700's on into the early part of this century, massive cornish pumps or equivalent were the vogue powered by steam. One Australian mine pumping system was claimed to be the largest in the world just after the turn of the century. It was installed at Beaconsfield in Tasmania and the mine, like so many other mines of the period, were beaten by problems and cost associated with mine dewatering. The owners of that mine are looking at the feasibility of dewatering using surface drilled wells. Much simpler and smaller pumps are the order now and it is feasible to use boreholes instead of shafts to contain the pumps or else to use the holes to convey discharge waters to the surface from pumps located in drives or stopes.

Jan 1, 1988

In-seam drilling is conducted mainly to drain coal of gas and/or water prior to development or extraction. The requirements of inseam drilling for gas drainage have mainly surpassed the technical limits of rotary drilling and are mainly being addressed by guided down hole motor drilling, albeit at a higher cost. There is an increasing application of in-seam drilling to detect geological structures or other hazards or their absence in advance of mining to reduce the risks of underground mining. Close collaboration between miners, drillers, geologists, researchers and suppliers over the last four years has seen many advances made to improve the accuracy and reliability of inseam drilling. With such developments will come closer control over the ventilation and safety of future mining under deep gassy conditions, but not without costs. The paper summarises the current applications of inseam drilling, recent technological advances and the next generation survey and geophysical sensing tools which are currently being developed

Jan 1, 1998

The information age has arrived. In every aspect of life, at the end of the second millennium, computers and information technology have made significant inroads. In mining there has been huge growth in the use of digitally controlled systems. From resource evaluation to mine planning to daily operations, information is being acquired, analysed, modeled and presented, using state-of-the-art information technology. Explosives, too, have moved into the information age. Computer controlled trucks and manufacturing plants have been developed and are now a regular feature on many mine benches. The next challenge for the explosives industry as a whole is to integrate blast initiation with information technology. The benefits are there, both to the supplier and to the end-user. Much has been written in the past about the potential for blast improvement but there are other significant advantages to a digital initiation system. These include security from unauthorised use, stock control and minimisation, reliability through testability and ease of use to name a few. So why is it taking so long? Surely the complexity of an electronic initiation system is far less than that of mobile phones that have been around for a long time. The answer, it seems, lies in the level of new technologies that need to be developed. There are enormous technological hurdles to be overcome in order to put into the market a cost-effective, reliable, user-friendly electronic initiation system. The most significant of these are:Safely and reliably initiating an explosive from an electronic device powered by a small capacitor. Prior to the development of electronic detonators primary initiation of explosives was by shock tube spit or by passing large currents and voltages down a pair of wires. Electronic detonators do not have that luxury. For example the energy stored in a æBeethovenÆ exploder is more than 500 times greater than that available to an electronic detonator. Communicating to a multitude of devices over very long cables installed by miners in harsh conditions. The deployment of an electronic detonator system has been likened to building a large telephone exchange in the rain and getting it to work perfectly first time! New communications protocols needed to be developed and tested. Wiring and connection systems have to be designed to survive the mining environment. In spite of these technological hurdles most of the major explosives manufacturers have persisted with electronic initiation systems and we are now, in 1999, starting to see the results of these multi-million dollar efforts. At SMI we are often asked many questions about this technology. The remainder of this paper seeks to answer those most often asked. As with any business linked to information technology todayÆs breaking news is tomorrowÆs archive and we expect the rate of development and understanding to accelerate as these technologies become accepted by the global mining industry.

Jan 1, 1999

By S P. Suthers, J M. F Clout, J J. Campbe

An advanced technique for modelling hydrocyclone separation performance has been developed. This technique is based on the combined modelling of hydrocycloning parameters and ævirtualÆ iron ore feed. The virtual feed modelling was performed using a novel (in-house) software package called æRecognitionÆ, which uses data from optical image analysis to classify the particles in certain size fractions according to total iron content and calculates data for every grade class. These data include the average mineral composition and density of every liberation class in every size fraction. This information about every size fraction, representing the ævirtual feedÆ, was input to the mineral processing modelling package USIM PAC. The hydrocycloning process was then modelled for this virtual feed using the Plitt hydrocyclone model. Empirical calibration coefficients for the hydrocyclone model were calculated using an optimisation procedure in Excel. Pilot-scale hydrocyclone beneficiation experiments were performed on an iron ore blend, using different hydrocyclone pressures and per cent solids in the feed pulp. These experiments were modelled and the modelling results were compared with the experimental results. The new modelling approach enables prediction of the recovery of each mineral in the products, calculation of the total iron grade and recovery, and optimisation of iron ore beneficiation using hydrocyclones.

Jan 1, 2005

By Lunardi P, Pelizza S

The link between the Lecco bypass and major road SS36 (Italy) requires the construction of a double two-way tunnel (through the mount San Martino carbonatic massif). The tunnel excavating section is about 90 sqm through mount San Martino carbonatic rocks. The mountain sides are unstable and are often the scene of large collapsing landslides (tens of thousand cubic metres). The tunnels are very close to the mountain sides. The use of blasting induces vibrations which may reach the Lecco built-up area. With a view to avoiding such dangers the excavating operations were carried out in two successive stages: - opening a pilot tunnel, whose section is about 10 square metres, by a full face TBM to eliminate the more intense vibrations which are generated by the first opening charges; - successive enlargement by blasting.

Jan 1, 1987

By P H. Warton

It is proposed to construct a gold extraction plant at Matatoki, near Thanes. Ore to be processed at the mill will come from reopened and enlarged underground mines north of Thanes. The project has been described in some detail in environmental impact reports (Worley Consultants Ltd 1984, 1987), and is now at an advanced stage in terms of obtaining the required statutory approvals.

Jan 1, 1987