Search Documents

By Warren L. J

In the mineral processing industry solid-liquid separation within a thickener usually requires the addition of a synthetic flocculant to enhance the settling rate of fine particles. The characteristics of the resulting flocculated suspensions may vary considerably depending upon the physical and chemical conditions which prevail during the flocculation process. For example, parameters such as flocculant type, dosage and solution concentration, surface chemical characteristics of particles and the suspension agitation conditions can influence the degree to which the particles aggregate. Aggregated suspensions exhibit various structures, and range from those composed of small, dense aggregates to those containing large, voluminous aggregates. The size distribution and structural type of the aggregates which form within the feed-well of a thickener can have a dramatic effect upon overall thickener performance. Thickener performance cannot be optimized without optimization of the aggregate structure produced in the feed by synthetic flocculant addition. This has required the development of new techniques to quantify the nature of aggregated suspensions, details of which are presented in this paper.

Jan 1, 1989

By S Viviers, G Ratner

Ventilation is part of all underground mine operations and is undertaken in order to introduce fresh, cool air to the workings and to remove stale, affected air. It is problematic to obtain efficient and accurate estimates of volume flow and static pressure in the installed operational configuration for the auxiliary axial flow fans.An empirical method was developed to estimate the static pressure and volume flow through a calibrated differential pressure port on axial flow fans. Prior to shipping, each fan is performance tested according to BS 848 (ISO 5801) to establish the fan performance curves. In addition to the standard required parameters captured to fully describe the performance, the differential pressure is measured across the fan rotor to enable correlation with the characteristic fan curve.The method was implemented on a ruggedised tablet PC platform. This compact platform is then used to calculate the volume flow rate from the differential pressure sensor measurement input via a USB port. The result is a real-time measurement of volume flow and operating point of the fan system. This can be used effectively in overall modelling of the mine auxiliary ventilation systems and calculation of system resistance could provide a health indication of the fan and duct system.CITATION:Ratner, G and Viviers, S, 2013. Underground auxiliary ventilation monitoring and diagnostic system, in Proceedings The Australian Mine Ventilation Conference , pp 57-62 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 1, 2013

The celebrations which took place in 1986 to mark South Australia's Jubilee 150 served to focus attention on all aspects of the State's heritage. Until that time the sites and relics of South Aus- tralia's early mines had been generally neglected. Marked by the ruins of enginehouses and littered with the remains of the massive technology of the Industrial Revolution, these sites have now been recognised as containing the threads of a fascinat- ing story. In the early days of settlement the economy of the Colony was based on land and farming. Droughts caused periods of economic depression which were alleviated by chance discoveries of gold, lead, silver, and copper ore. Some of the mines which were opened on the copper deposits were the largest in the world at that time and their names well-known throughout mining circles. Working by hand with primitive equipment, the early miners excavated vast networks of shafts and stopes often extending to great depths: at Moonta- Wallaroo Mines for example workings extended to 860 m below ground. Because of the presence of underground water, mining to these depths would not have been possible without the Cornish pumping engine. Operated by steam power these massive engines and their associated equipment were transported from Cornwall by clipper and delivered to the mines by bullock cart. At this time the engines were at the peak of their devel- opment and, although expensive to import and install, they were highly reliable: the engine oper- ating Hughes pump at Moonta worked continu- ously for sixty years without a major breakdown.

Jan 1, 1987

By Browne TJ

On 13 October 1993, a shallow earthquake registering 7.1 on the Richter Scale occurred near Tauta in the Finisterre Range of Papua New Guinea (PNG) killing 37 people. The aftershock series lasted three months and resulted in considerable landslide damage that destroyed villages, food gardens and airstrips, and blocked rivers causing catastrophic flooding. These effects have irrevocably altered the form of many of the valleys and rivers draining into the Markham and Ramu valleys.The earthquake occurred in a pilot study area for a landslide hazard mapping project being carried out by the PNG Geological Survey that commen-ced in April 1993. Comparisons made between areas identified as unstable during the study with those damaged by the earthquakes show good correlation.It is concluded that aerial photograph and Landsat TM imagery interpretation can be used with a high degree of confidence to identify potential landslide hazards in mount-ainous terrain. Landslide hazard maps are promoted as a tool for use in the route planning of roads and powerline corridors, as well as for identifying vulnerable communities.

Jan 1, 1994

The drilling and evaluation of bore cores provides the best available statistical basis for characterizing a coal prospect. Important, long-term decisions by management frequently must be based on the results. The majority of coal mined presently is used for steam raising or the production of metallurgical coke. Common bore core tests and analyses appropriate to this usage can be cate- gorized as non-destructive, chemical, physical, petrographic, caking/plastometric and propert- ies of non-coal material. The major tests within each category are described. Certain specific information from the bore cores is required by the coal geologist, mining engineer, coal preparation engineer and the user, either individually or as a group. The optimal bore core evaluation test pro- gramme is the one which satisfies the needs of all the professional disciplines with the grtatest speed and at minimal cost. The principal steps in such a programme are listed. There is an urgent need for a bold new Australian standard to provide the necessary guidelines to an industry which at present lacks uniformity in its approach to the task.

Jan 1, 1977

The emerging discipline of ægeometallurgyÆ is not new but is becoming increasingly recognised as a discrete and high-value activity that reflects an ongoing commercial and cultural trend towards more effective mine site integration and optimisation. Geometallurgy involves a quantified and spatially constrained approach to ore characterisation in terms of relationships to critical processing performance. Industry recognition of the need for large-scale, integrated geometallurgical research is currently supporting a major new research initiative. The AMIRA International P843 æGeMIIIÆ project (geometallurgical mapping and mine modelling) is a cross discipline collaboration involving four major Australian research groups; CODES the ARC Centre of Excellence in Ore Deposits at the University of Tasmania, a world leader in economic geology-related research; the Julius Kruttschnitt Mineral Research Centre (JKMRC) at the University of Queensland, a world leader in mining and mineral processing research; the WH Bryan Mining Geology Research Centre (BRC) at the University of Queensland, which aims to be a world leader in mining geostatistics, operations research and optimisation in mine design and planning; and CSIRO Exploration and Mining in the area of automated core logging. The project is currently supported by 19 global mineral companies. The project aims to deliver fundamental knowledge, tools and methods for more effective approaches to geometallurgical definition of mineralogy, element deportment and texture that can be linked to mineral processing performance and efficiency at a range of scales. Outcomes are improved predictive indices of processing performance that can be embedded in resource block models to define processing domains, which can be exploited in mine planning and optimisation. To achieve these aims the project is involved in a range of technology developments that include more automated core logging technologies, new applications of automated microscopy and development of software-based texture analysis and categorisation techniques. Attributes derived from these measurement technologies are used to develop predictive processing models linked to new small-scale physical testing regimes.

Jan 1, 2009

By Thomas W

Due to record low tin prices and an uncompetitive position in world markets, the Renison tin mine has undergone three major phases of restructuring in the last three years. This has involved substantial job losses, almost all of which have been through voluntary retrenchments. Retrenchments took place in 1988, 1990 and 1991.The last phase of restructuring was the most dramatic, as many aspects of the operation of the mine were changed. New pay structures were introduced, and the miners' contract system was scrapped. Drastic pay cuts occurred in many areas, although the opportunity was also taken to increase pay at some of the lower levels where inequities existed. Work practices were changed, as was the management structure.

Jan 1, 1992

The first introduction of automatic control systems for flotation occurred about fifteen years ago. The early control work coincided with the introduction of on-line assaying using XRF techniques. This OSA availability, coupled with the emergence of small digital computers suitable for process control in the late 1960-s, meant that the necessary process information and control hardware existed for flotation control experiments. A period of intensive research related to flotation control. ensued. A great deal of effort was devoted to the development of mathematical models of flotation. Plant experimentation sought to understand the effects of a range of flotation variables on the process. Finally, control loops were proposed and plant tested. An evolutionary pattern emerges when the range of flotation control installations is examined. The earliest systems had as objectives process stabilisation using reagent control. There were also some early attempts at flotation optimisation procedures, again using reagent variation. Current work is still associated with the same objectives. One of the difficulties with flotation control has been to recognise and define clear and precise control objectives. More emphasis is now placed on cleaner control which has the advantage that the objectives are usually well defined. A number of flotation control systems which cover a range of control system types is discussed. Based on this accumulated experience,a list of good and bad practice in flotation control is Proposed.

Jan 1, 1983

By B Yang, L Wang, C Y. Ng

Flotation process intensification is often achieved through changing chemical reagent scheme or flotation machine or both, which likely brings a hefty burden to the flotation plants in terms of capital or operating expenditure. A novel approach to flotation process intensification is the use of acoustic sound, which has been demonstrated to be effective in improving the flotation of various mineral systems with different type of flotation cells. This approach was based on the dynamic stabilisation effect of acoustic sound on the flotation froth. The present work aims to understand the influence of various experimental conditions on the effectiveness of the approach. First, the effects of sound frequency and amplitude were studied with column flotation of silica particles. Results showed that the flotation performance was improved only within a certain range of frequencies and above certain amplitude. The study was then extended to the mechanical flotation of quartz particles with various size ranges and at two solids concentrations. With sound, the recoveries of different size fractions within the range of 20–212 μm were all increased. In particular, the recovery of 150–212 µm particles was increased from 0 per cent to approximately 25 per cent, demonstrating the potential for extending the upper limit of particle size in flotation by using acoustic sound. Furthermore, mechanical flotation of chalcopyrite particles at various collector dosages (50–150 g/t) was carried out with and without sound. Results showed that the increment of the final flotation recovery was increased with sound at different collector dosages. Overall, acoustic sound has the potential to be used as an effective and versatile method for flotation process intensification.

Aug 24, 2022

Although the diesel engine is normally considered a tried and proven power source, many new and exciting diesel design concepts are being evaluated in engine development laboratories around the world. Three such programs currently underway at Cummins Engine Company are discussed. The turbocompound engine converts into power exhaust heat energy which is normally wasted. It does this by incorporating after the turbocharger a low pressure gas turbine which is gear driven to the crankshaft. The adiabatic engine has no conventional cooling system. It converts into useful power most of the heat energy normally rejected to the coolant. The series boost turbocharged engine uses seperate low and high pressure turbochargers to increase engine output and improve transient performance. These design concepts make possible increases in diesel engine thermal efficiency from the current 33 to 38 per cent range to the 50 percent range.

Jan 1, 1982

Optimisation of capital in the development process is critical to the profitability of any new mining venture. The process of optimisation should apply to all aspects, that is the financing, management, revenue, reporting and, of course, the development of the project. Unfortunately, too much emphasis has been placed on the optimisation of the financing or reporting aspects and too little on the project itself. This paper addresses the latter.

Jan 1, 1991

Over the last five years Du Pont (Australia) Ltd has developed a commercial range of new generation emulsion based explosives concurrently with the development of new explosives-placement systems. The paper outlines Du Pont's emulsion technology and history of product development from the initial emulsions (Tovex E & EL) to emulsion/ANFO blends (Tovex BE) through to the most recent development of Du Pont's SOL emulsion component. The paper also outlines the development of materials handling systems on site to load waterproof bulk explosives from the original pumper trucks through to the multipurpose agitator bowl blending and pumping units at the heart of Du Pont's SOL emulsion system currently available within Australia. The last section deals with some of the more important features of enhanced agitator bowl truck designs and outlines examples of the complete SOL emulsion system and methods of operations currently practiced at specific mines within the Bowen Basin coalfields.

Jan 1, 1986

By L C. Thompson

BioLix is the term for a new class of biologically-derived lixiviants for precious metals (gold and silver) recovery. BioLix can be used as an alternative to cyanide on virgin and spent ores. The BioLix process is based on inducing microbial enzymatic reactions that generate organo-lixiviant chemicals. The bioprocess involves a two-stage culture strategy. First, specialty microorganisms are cultured to generate a high biomass. Then, a food-grade quality amendment is introduced that forces the microorganisms to produce the organo-lixiviant. The second-stage culture is applied to the ore where the microbial/lixiviant system acts on mineral surfaces to extract precious metals. The process operates at ambient temperatures and near neutral pH. This paper will examine the BioLix process through an extensive laboratory development and demonstration project. Laboratory development consisted of identifying and isolating specialty microorganisms and inducing agents for the production of the organo-lixiviant solutions. A demonstration was performed on low-grade and high-grade oxidised ore from the Buffalo Valley mine in Nevada, USA. Results indicate that the BioLix process was comparable to cyanide in terms of gold recovery and operated at near neutral pH and ambient temperatures. Applications for the BioLix process will be discussed including spent-ore re-leaching, cyanide replacement for virgin ore, and in situ mining.

Jan 1, 2004

By E du Plessis, M Rowley, M Fallon, F Golenya, R Swanson, I Robertson

"Check sampling programs were undertaken at Barrick Australia Pacific LimitedÆs Lawlers and Plutonic mine sites in Western Australia. The programs identified that the sampling, sample preparation and assaying protocols required modification to ensure acceptable precision (reproducibility) for each gold mineralisation type. These case studies describe the processes used to identify the: inconsistent precision different types of test work programs that were conducted to quantify the appropriateness for each mineralisation type steps used to modify the protocols.The type of test work conducted included: a duplicate series heterogeneity test for particulate gold mineralisation in the Lawlers gold deposit screen fire assay test work on duplicate subsamples for arsenopyrite associated mineralisation at the Plutonic gold deposit.Each test work program required a detailed scope specifying the sample selection criteria, sample preparation and assaying steps. The aim of the test work flow chart design was to ensure the assay precision between the different particle sizes or duplicate sample pairs could be measured and calculated. In the screen fire test work the true grade of the primary sample was calculated and compared against each subsample.A high quality assay laboratory was utilised for the test work. All samples were fire assayed and the gold grade determined using a gravimetric finish. The assay results were validated and the data was analysed using tables and graphs in spreadsheets. Following data analysis a modified sample preparation and assaying protocol for each mineralisation type was designed for use by the principal assay laboratories. Following implementation of the new protocols, routine check samples were collected during the sample preparation and assaying stages to monitor the performance of the new protocol.CITATION:Fallon, M, Rowley, M, Du Plessis, E, Golenya, F, Robertson, I and Swanson, R, 2012. Confirming the sampling, sample preparation and assaying protocols used at two Yilgarn gold deposits, in Proceedings Sampling 2012, pp 47-62 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Aug 21, 2012

It is very rare in the underground hard rock environment to find a deposit that is ideally suited to a specific mining method. Usually the irregular shape of the orebody will allow the deposit to be extracted by more than one mining method. During the prefeasibility stage, a number of conceptual mine designs are generally evaluated to see which offers the best method of extraction for the deposit. The selected method is usually based on key decision criteria such as the overall extraction of the orebody, the amount of metal produced annually and the unit cost of production. Often the prefeasibility study document will state that the project has an NPV of æxÆ million dollars. This statement can be made without any quantitative consideration of the likely risks of the mining methods reviewed or the level of confidence in the estimation of the NPV. By assigning a probability of failure to each component of the mining cycle a measure of the risk for each method can be determined. One mining method may provide the highest NPV when it is performing well, however, there may be a higher risk of a major failure impacting on the performance of that method, eg the failure of a mass blast of a crown or rib pillar. This paper will present a flowsheet approach to the use of risk analysis for determining the likely production rates of different mining methods. This framework allows the annual metal output to be estimated and from this the NPV for each method. A level of confidence can be applied to the estimated NPV for each option. An example will be presented on how this technique has been used within the Normandy Group.

Jan 1, 1998

By J Stiefenhofer

"*This is an abstract only*Construction of geological models for kimberlites has historically largely been based on visual volcanic textures and features, with chemical data only collected on an ad-hoc basis depending on the level of perceived complexity observed in the geological data. The focus of this paper is a high-level view of the impact an initial absence (or lack) of relevant chemical data had on two kimberlite resource models as well as how the magnitude of the problem increased once the resource estimation process commenced (Stiefenhofer, 2013). The impact of ignoring chemical data on a project assessment where micro-diamond estimation techniques are employed, is also discussed. Resource estimates based on micro-diamond data are critically dependent on the use of the correct geological model since stationarity of the size frequency distribution is key to the generation of correct grade estimates. A multilevel approach is advocated where the volcanological/visual model is verified using chemical data and both are in turn verified by the diamond data.CITATION:Stiefenhofer, J, 2013. The use of chemical and metallurgical parameters to enhance the economic value of kimberlite resource models, in Proceedings The Second AusIMM International Geometallurgy Conference (GeoMet) 2013, pp 101-104 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Sep 29, 2013

By W Farnworth, D Fergusson

Estimation of productivity is a key factor in the design of hydraulic mines and in assessing their economic feasibility. A published Russian formula for hydraulic mining monitor cutting rates overstated productivity by up to 2 tonnes per minute (251%) when applied to Solid EnergyÆs hydraulic mines. A new formula, taking into account additional productivity factors, was derived by Solid Energy and produced an acceptable correlation between predicted and actual cutting rates inNew Zealand and overseas hydraulic mines, with an average error of approximately 0.1 tonnes per minute.   Another key factor in hydraulic mine design is the transport of coal slurry via flumes. Solid Energy carried out a series of 80 full scale tests in a surface flume installation, varying the gradient and coal:water ratio. Both steel flumes and plastic-lined flumes were evaluated. A modification of the Chezy Open Channel Flow formula, including a factor for slurry density, gave a reasonable correlation between actual and predicted flows. It is believed that this Solid Energy formula is suitable for the design of flume installations for hydraulic mining.

Jan 1, 2004

By W Zhu, J H. Zhao, H Ma

The permeability coefficient is an essential parameter for the study of seepage flow in fractured rock mass. This paper discusses the feasibility and application value of using readily available RQD (rock quality index) data to estimate mine water inflow and grouting quantity. Firstly, the influence of different fracture frequencies on permeability in a unit area was explored by combining numerical simulation and experiment, and the relationship between fracture frequencies and pressure and flow velocity at the monitoring point in fractured rock mass was obtained. Then, the stochastic function generation program was used to establish the flow analysis model in fractured rock mass to explore the relationship between flow velocity, pressure and analyse the universal law between fracture frequency and permeability. The concepts of fracture width and connectivity are introduced to modify the permeability calculation formula and grouting formula. Finally, based on the on-site grouting water control case study, the rock mass quality index is used to estimate the mine water inflow and the grouting quantity. The results show that it is feasible to estimate the fracture frequency and then calculate the permeability coefficient by RQD. The relationship between fracture frequency and RQD and the relationship between structure surface frequency and permeability follow an exponential function. The calculation results are in good agreement with the field monitoring results, which verifies the rationality of the calculation method. The relationship between the rock mass RQD index and the rock mass permeability established in this paper can be used to invert the mechanical parameters of the rock mass or to evaluate the permeability and safety of the rock mass, which is of great significance to the prediction of mine water inflow and the safety evaluation of water inrush disaster management.

Nov 29, 2022

By V Sahajwalla, S Shin

Research activities to classify the quality of iron oxides have a long history but most of such activities are for the existing processes such as blast furnace or DR plant. Therefore the newly developed process, such as the COREX process, needs new standardisation although some basic functions of the new process have similarity to the existing processes. Many researchers (Hauk, 1990; Cho et al, 1998) in the field of COREX process have conducted investigations since the early stages of the process development and activities are underway for further plant optimisation. As Agrawal and Oshnock (1995) pointed out, because coke is not included in the COREX reduction shaft the strength requirement of the feed materials in COREX process will be more demanding than that in the blast furnace. This condition is similar to Midrex DR plant but the main reduction gas of COREX plant is carbon monoxide generated from coal combustion while that of Midrex DR plant is hydrogen from natural gas.

Jan 1, 2000

I stand here as a financial advisor who has been particularly close to the whole concept of reporting, independence and all the issues that are brought together in Release 149. However, I was asked to introduce this session by dealing with matters of Prospectuses, Part B's, 3J3's, 12G's and other requirements to report. Now I find it very interesting that one of the keynote issues is whether or not one should have a panel from which one chooses the so-called expert, and this is to deal with the question of independence.

Jan 1, 1989