Search Documents

By I Canbulat, J Oh, A Mcquillan, D Payne

This paper presents a new risk assessment tool for coal mine excavated slopes. This new empirical-statistical Slope Stability Assessment Methodology (SSAM) is intended for use by geotechnical engineers at both the design review and operational stages of a mine’s life to categorise the risk of an excavated coal mine slope. A likelihood of failure is determined using a new slope stability classification system for excavated coal mine slopes developed using a database of 119 intact and failed case studies sourced from open cut coal mines in Australia. Consequence of failure is based on slope height and stand-off distance at the toe of the excavated slope. Results are presented in a new risk matrix, with slope risk being divided into low, medium and high categories. The SSAM is put forward as a new risk assessment tool to assess the potential for, and consequence of, excavated coal mine slope failure. Unlike existing classification systems, assumptions about the likely failure mode or mechanism are not required. Instead, the SSAM applies an approach which compares the conditions present within the excavated slope face, with the known past performance of slopes with similar geotechnical and geometrical conditions, to estimate the slope’s propensity for failure. The SSAM is novel in that it considers the depositional history of strata in an excavated slope and how this sequence affects slope stability. It is further novel in that it does not require explicit measurements of intact rock, rock mass and/or defect strength to rapidly calculate a slope’s likelihood of failure and overall risk. Ratings can be determined entirely from visual observations of the excavated slope face. The new SSAM is designed to be used in conjunction with existing slope stability assessment tools. CITATION:Mcquillan, A, Canbulat, I, Payne, D and Oh, J, 2018. New risk assessment method for coal mine excavated slopes, in Proceedings The Fourth Australasian Ground Control in Mining Conference (AusRock), pp 473–495 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 30, 2018

By D Gericke, R Cooke

This paper presents an assessment of the status in design and operation of deep level backfill distribution systems by referring to case studies and practical experience. The improvements in design and operation of the systems can largely be attributed to an improved understanding of slurry flow behaviour and a corresponding integrated design approach that includes slurry flow modelling, system design and application of the latest technology. The conclusions summarise the lessons learnt from such case studies and stresses the importance of design reviews and audits of existing systems as a means to ensure that the mistakes of the past are not repeated in the future.

Jan 1, 1998

By R Castroviejo, E Pirard, L PTrez-Barnuevo

Process mineralogy provides the mineralogical information required by geometallurgists to address the inherent variation of geological data. The successful beneficiation of ores mostly depends on the ability of mineral processing to be efficiently adapted to the ore characteristics, liberation being one of the most relevant mineralogical parameters. The liberation characteristics of ores are intimately related to mineral texture. Therefore, the characterisation of liberation necessarily requires the identification and quantification of those textural features with a major bearing on mineral liberation. From this point of view, grain size, bonding between mineral grains and intergrowth types are considered the most influential textural attributes. While the quantification of grain size is a usual output of automated current technologies, information about grain boundaries and intergrowth types is usually descriptive and difficult to quantify to be included in the geometallurgical model.Aiming at the systematic and quantitative analysis of the intergrowth type within mineral particles, a new methodology based on digital image analysis has been developed. In this work, the ability of this methodology to achieve a more complete characterisation of liberation is explored by the analysis of chalcopyrite in the rougher concentrate of the Kansanshi copper-gold mine (Zambia). Results obtained show that the method provides valuable textural information to achieve a better understanding of mineral behaviour during concentration processes. The potential of this method is enhanced by the fact that it provides data unavailable using current technologies. This opens up new perspectives to the quantitative analysis of mineral processing performance based on textural attributes.CITATION:PTrez-Barnuevo, L, Castroviejo, R and Pirard, E, 2013. New perspectives on quantitative textural analysis, in Proceedings The Second AusIMM International Geometallurgy Conference (GeoMet) 2013 , pp 191-198 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 29, 2013

By Drain P, Dibdin T. R

THE completion of the Linda incline man and supply haft at the Mount Morgan Gold Mining Oompany's mine led to an investigation of the various safety gears in general use in mining shafts. One of these gears completely fulfilled the necessaryconditions. This paper endeavours to give a description of the man car and safety gears now operating in the before mentioned shaft, together with the main considerations leading to their design and sub equent adoption. Fig 1 diagramatically shows a longitudinal section of this shaft.

Jan 1, 1911

Numerical simulation by a finite element computer code has bee* used to identify key stages in the initiation of confined bulk explosive by cast primers. The simulations have been verified by comparison with experimental field measurements of shock arrival time versus distance above the primer for a relatively sensitive emulsion doped with ammonium nitrate prills. Further simulations were performed examining the effect of primer size in a relatively insensitive blend of ANFO and emulsion. Immediately above the primers, changes in shock velocity in the explosive were caused by the interactions between shocks originating from different surfaces of the cylindrical primers. At a distance up the explosive column corresponding to about one to two borehole diameters, the arrival of shock reflections off the borehole walls caused a sudden acceleration up to the confined steady state detonation velocity. The simulations reproduced experimental observations that primer size has only a weak effect on changes of shock velocity with distance for confined explosives. However, it was predicted that primer size has a strong influence on the intensity and duration of the pressure pulses that bulk explosive send into the rock surrounding the primer region.

Jan 1, 1990

By T E. Norgate

Salinity in Australia is caused by over irrigation and land clearing for agricultural use over the last 100 years. It is now the biggest threat to the quality of land and water in the Murray Darling Basin and Western Australia. Pumping the saline waters straight into the ocean or transporting the solid residue (mainly sodium chloride) to the ocean after evaporation of the water is expected to cost the taxpayer millions of dollars every year. This paper proposes that the salinity problem of Australia, at least in part, can be converted to an asset rather than a liability if it is exploited and used to make value-added products. The more value made out of saline waters, the more saline water is processed and therefore the more salt is extracted from the land. The value-added products that can be made out of saline waters are numerous and diverse. Rough calculations show that value addition to the saline waters could potentially generate up to $A 200 million per annum business in the Murray-Darling Basin. Although it is a challenge to make cost competitive products and find markets for these products it is possible that up to $A 100 million per year may be gained from import substitution. Value addition to salinity would also reduce the threat on the environment and existing agricultural industry. Investment to add value to salinity will create business in the region, nurture the local small population communities, and increase services and long-term employment.

Jan 1, 2002

When lying over 200-250m depth, many seams and surrounding strata are gassy enough to create mining difficulties , particularly in highly productive longwalls as well as in their development headings. In addition to the gassiness of seams or stra- ta in the outgassing volume around working, the shape expansion and limits of this one influences much the intensity of gas emission. These charac- teristics of outgassing volume differ very much ac- cording to the permeabilities of the seams and strata encountered by their fracturation due to mi- ning. Moreover, the shape of the outgassing volume is very much modified by the rate of advance of the face. In nearly impermeable deposits, gas flows from a limited outgassing volume. When the rates of advance of a face are medium or low, the shape and dimensions of this volume do not change very much and outgassing volume is translated progressi- vely with the face advance. This explains why, in the past, it was observed that there was for each seam an average steady specific emission of gas, round which the volume of gas evolved per mined ton or per mined unit area, calculated over a cer- tain time, was oscillating. Combined with a statisti- cal irregularity coefficient, this allowed prediction gas of emission and thus to take decisions for air ventilation, drainage, and eventually production.

Jan 1, 1988

By Chaves AP

This paper describes an investigation on the surface properties and mechanisms involved in the agglomeration of iron ore. For this purpose, an organic binder (carboxyl-methyl-cellulose (CMC)) was used in substitution of bentonite, the classic binder in iron ore concentrate agglomeration. Recently, a renewed interest of the iron ore producers in Brazil to replace bentonite for an organic binder, because of the economy that can be achieved in the, blast furnace operation. These savings are mainly due to the lower aluminum silicate addition which decreases slag volume and the improved pellet metallurgical properties which have the potential for lowering hot-metal production costs. Also organic binders are effective at lower addition levels, which results in lower storage and transportation costs. It is very important in Brazil because of the vast geographical area since transportation is made mainly by truck. Another advantage of organic binders is that they have low ash contents, and therefore most of the binders bum. off during the pellet firing operation. Previous studies have demonstrated the possibilities of the use of CIVIC, but in addition to its high cost, the pellets presented improper behavior at high temperatures or when prepared with high moisture levels. In the investigation here described, these problems have been solved through the addition of other reagents to CMC.

Jan 1, 1993

By Amanatidis A

In this paper, the kinetics of iron precipitation as sodium jarosite from aqueous solution is investigated. The determination of the reaction mechanism is attempted based on the experimental data of iron removal as a function of time, without using the characteristics of the precipitate.Experiments at the temperature range from 50° to 95°C were carried out with initial conditions of iron concentration IQ g/L, sodium sulphate concentration 25.44 g/L, sulphuric acid concentration 3.68 g/L, pH = 1.5 and agitation rate 600 rpm. Temperature greatly and positively influences iron precipitation from the solution and this is accompanied by pH decrease. The activation energy was determined using the maximum values of the precipitation rate, which were evaluated by polynomial fitting of the sigmoidal shape experimental curves, and it was found to be 44.37 kcallmole. The determination of the rate-controll ing mechanism was based on some criteria used for the discrimination among the three probable mechanisms of precipitation (diffusion, mononuclear nucleation, polynuclear nucleation). These criteria utilise various funetions of the recovery 'a' of iron precipitated versus time, the most important of which are the chronomals. The results of the kinetic analysis procedure showed that the polynuclear nucleation growth mechanism controls the precipitation of iron as sodium jarosite. This was confirmed by the high value of activation energy, excluding diffusion as the controlling mechanism.

Jan 1, 1993

By de Lassar de Pressigny Y

IRSID has in its laboratories two experi mental counter-current reduction furnaces allo- wing the simulation of the physico-chemical conditions of reduction in any gas-solid coun- ter-current process, including the blast furnace and direct-reduction shaft-furnaces. The counter current is realized by an electric furnace mo- ving along a laboratory tube filled with the material to be tested. The reducing gas stream in the tube travels in the same direction as the furnace After reduction, twenty samples, with dif- ferent degrees of reduction and which can be related to different levels of an industrial furnace, are taken from the tube and subjected to various quality tests. Experiments were realized to determine the behaviour of various types of industrial pellets when reduced under either blast furnace or shaft furnace conditions. The results show the large influence of the reducing conditions on any pa- rameter characteristic of the quality of the pellets : reduction efficiency, swelling, cru- shing strength and disintegration.

Jan 1, 1974

By Etheride MA

The evolution of economic precious metal and copper-gold deposits in high-level igneous terranes is dependent on very efficient fluid focussing. This is most readily achieved by contemporaneous deformation, igneous intrusion and hydrothermal activity. Mineralisation in these environments generally occurs in fault and fault-vein arrays developed in the cover sedimentary and volcanics sequences above older regional scale fault systems. Such reactivated fault systems an particularly prone to developing the complex fracture arrays, extreme local dilation and dramatic increases in permcahilit} that are necessary to efficiently focus hydrothermal fluid and produce large mineral deposits.

Jan 1, 1995

By Gole MJ

The Goodyear nickel prospect is located 45 km southeast of Kalgoorlie (31.04¦S, 121.80¦E) near the eastern boundary of Hampton Area - East Location 45 (Figure 1). Nickel mineralisation was discovered on the Goodyear prospect in March 1996 when a reverse circulation drillhole (GYC5), initially drilled in December 1995, was deepened to meet a minimum footwall penetration requirement of 20 in that had been set for the drill program. Approximately 3 in of sulphides averaging 4.9 per cent nickel was intersected from 296 metres down-hole, this being within 2 in of the first end-of-hole. Hole GYC5 was part of an eight hole drilling program undertaken by Titan Resources in late-1995. This program was designed to test whether nickel mineralisation in the Dunlop prospect, discovered by the Western Mining Corporation - BHP Camylia Joint Venture immediately east of the East Location 45 boundary, continued across the tenement boundary. The area targeted by the initial drill program had been explored by Western Mining Corporation in the mid-1980s using extensive surface sampling and a drilling program that included 17 RAB and percussion drillholes. None of these holes intersected nickel Mineralisation.\

Jan 1, 1996

By Roe P, Lowell A

This paper outlines software development and design work carried out by Mincom Pty Ltd in collaboration with Capricorn Coal Management (CAPCOAL) for computer based design of rehabilitated strip mine landforms at German Creek Mine. Current developments and future application areas for this software are also discussed in relation to other mines in Central Queensland. The development program was initiated in response to statutory requirements placed on mining companies in 1990 to produce a five year Plan of Operations which was to include a contour plan of the final rehabilitated mine landform at the end of the five year planning period. This plan was to be submitted to the Department of Resource Industries (DRI) by 1 December 1990. Due to the limited time given to prepare the plan, a work program was formulated in collaboration with Mincom Pty Ltd to develop suitable software to carry out the design work and provide the required plans and quantities. The software had to include computer based methods to allow design of the proposed landform in line with the rehabilitation strategy adopted by CAPCOAL at the time.

Jan 1, 1991

By J McQuie

The concentrator at WMCÆs Leinster Nickel Operation has operated with flash flotation in the grinding circuit since the early 1990s. There has always been a positive correlation between flash flotation Ni recovery and overall Ni recovery û however this relationship could be explained by differences in the ore, rather than by the action of the Flash flotation cell in reducing overgrinding of Ni. In July 2003, refurbishment within the plant made it necessary to operate the concentrator for a period with the flash flotation cells off. The resulting data set provided evidence that flash flotation in the grinding circuit changes the size distribution of Ni to reduce the amount of slow-floating fine (-7 ¦m) Ni produced. Ni recoveries in the finer size fractions were similar with flash flotation on or off û but because less fine Ni is produced when the flash flotation cells are operated, overall Ni recovery improved.

Jan 1, 2005

By Fejes A. J

The U.S. Bureau of Mines installed surface and subsurface instruments at a mine site in Colorado to monitor and characterize the overburden response to longwall mining. Instrumentation included a time-domain reflectometry (TDR) cable, a multiple-point borehole extensometer (MPBX), vertical- deformation surface monuments, and in-mine pressure cells for monitoring abutment, pillar, and gob loads with respect to the longwall face position. The purpose of the study was to collect data that could be analyzed to correlate the design of the mine layout to the resulting overburden failure response. Determining the extent of caving and fracturing is important in the and and semiarid Western United States because of the possible consequences to the fragile underground hydrologic systems upon which the land owners and users depend. This study is unique from past investigations because the overburden contains massive sandstone members that impose special conditions on the caving process and pressure redistribution above the longwall panels. This paper presents the results of this correlation study.

Jan 1, 1992

This paper discusses the use of tapered roller bearings in conveyor idlers. It shows that in medium and high capacity systems, tapered roller bearings can offer significant cost and performance advantages. In the next ten years, conventional conveyors will face increased competition from unconventional belt conveyors, pneumatic systems, pipeline "slurry" systems, unit trains and so on. The conveyor industry must meet these challenges by innova- tive use of technology. Conventional belt conveyors must continue to show the lowest cost per tonne-km or lose their position in the market. Tapered roller bearings can contribute to the achievement of this goal. The concurrent resources boom and liquid fuel crises may well see a decline in the use of heavy trucks for bulk material handling over moderate distances 10 to 50 km. There appears to be a trend in the conveyor industry to go to higher speeds with improved belting in conven- tional widths. The transmission of more material over a given period of time will place more demands on conveyor idler bearings. Australia has in general followed the European practice of using deep groove ball bearings in conveyor idlers.

Jan 1, 1978

By Cudmore JF, Rowlands D

Incidents associated with spontaneous combustion of coal have resulted in the loss of many lives and considerable capital and equip- ment. Nevertheless, the factors controlling the propensity of coal to spontaneous combustion are not clearly understood and there is a need for research to study the effects of rank, petrog- raphy, moisture contents, etc. This has been attempted in a study of the propensities of selected Queensland coals to spontaneous combustion. An adiabatic calori- meter was constructed to study the self-heating of a large number of coals. Chemical and petro- graphic analyses of the coals were determined and an attempt was made to relate these propert- ies to the self-heating characteristics of the coal. The results show a strong relationship between rank and self-heating characteristics and that petrographic composition of coal may also be of importance. Some observations on the application of the laboratory results to the practical situation are made as are recommendations for future research.

Jan 1, 1981

This paper first describes the essentials of the slurry shield method and its achievements, then problems encountered during driving tunnels and their countermeasures, and finally shows problems to be solved in the future. The author works at Tekken Construction Co., Ltd. as a director. All the data cited are based on material gained from the slurry shield tunneling works undertaken by the said company. The mark, viz*, indicates that Tekken Construction Co., Ltd. has obtained or is applying for a patent in the U.S., Europe and Japan. 1. CONSTRUCTION RECORDS BY SLURRY SHIELD METHOD AND ITS PROBLEMS (1) Shield machines in the future should have the following characteristics; a. to be able to drive less cohesive soil b. to make no change to the ground water table level c. to make it possible to let people work in normal air pressure d. to cause less settlement at the surface To meet the above conditions various kinds of mechanical shields have been are tried, viz. limited air pressure type, rotary cutter with slit regulator, screw-discharge type, blind shield, etc. As far as the author knows, however, they are not 100% successful. Tunnels need their own accuracy in accordance to the usage. Both ease of driving

Jan 1, 1976

By Lawson F

A rotating disc geometry has been used to provide a uniformly accessible surface for a kinetic study of the cementation of the metals cadmium, lead and silver from dilute aqueous solutions. This work is an extension of studies carried out on the Cu/Zn and Cu/Fe systems for which the rection rate was found to be completely solution-phase mass-transfer controlled. When the amount of material deposited was greater than 0.2 to 0.4 mg/cm2 there was an apparent enhancement in e which is attributed to the formation of a roughened deposit. This same phenomeon was obseived in the Cu/Zn Cu/Fe systems. Again, the rate of reaction of each system investigated was found to be solution-phase mass ,..~sfer controlled.

Jan 1, 1970

By Osborn G

The bulk flotation behaviour of an industrial rougher bank has been determined with a view to characterising the size iepend ent behaviour of the identifiable nineral groups present. A relatively simple flotation model, based on first order kinetics and the assumption of perfect mixers in series ias been used to provide a fit to the operation of the cells. The adequacy of the model is discussed in relation to the characteristics of the ore and the size iependancy of the parameters. It is shown that improved fits are possible if the model accounts explicitly for this size dependancy and demonstrated how the model may be of use in prediction of the grade recovery relationships for different operating conditions as an aid to plant optimisation.

Jan 1, 1986