Search Documents

By J Kovacs

Underground development drill and blast practices have generally remained unchanged for decades. Historically, development optimisation has focused mainly on the application of perimeter control products in order to reduce overbreak, and efficiencies in development cycle times to increase advance rates. In today’s environment of ever increasing operating costs and lower ore grades, it has become even more critical to focus on the optimisation of drill and blast in development mining. It is a crucial component in ensuring mining schedules are maintained, but more importantly achieving the objective of getting to the orebody in the shortest possible time.This paper will focus on the development optimisation process used in a trial at Xstrata’s George Fisher Mine in North Queensland. Not only did the trial include the typical optimisation areas of charge loading practices, perimeter control methods, drill design standardisation and quality control processes, it also investigated the significance of delay accuracy with regards to perimeter control and drill design optimisation.One of the key measures of the trial was a comparative analysis between baseline development and development with the staged introduction of optimisation elements using 3D photogrammetry as a validation tool. A detailed cost analysis between the various stages was also a key measurable of the trial.The results of the work undertaken at George Fisher have shown that the accuracy of electronic detonators can produce significant benefits in development blasting. When combined with standard optimisation philosophies a substantial reduction in overbreak, ground support requirements and development cycle times can be achieved, whilst still being able to reduce the overall development operating costs.CITATION:Kovacs, J, 2014. Mine development optimisation – an evolutionary process, in Proceedings 12th AusIMM Underground Operators’ Conference 2014 , pp 51–56 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Mar 24, 2014

By Redman P. G, McMahon B. K

A simple technique for evaluating the field stress ratio is presented, based on the results of extensometer or convergence tape measure- ments taken in an advancing tunnel. This tech- nique also yields a value for the rock mass modulus, provided Poisson's Ratio is assumed. The results of two case studies are presented illustrating the effectiveness of the method.

Jan 1, 1981

By Loo C. E

Thirty two polyacrylamide flocculant samples were selected from the wide range offered to the Australian coal industry. An extensive test program was conducted to consider the properties of the flocculants, the substrates, the process conditions and the water chemistry encountered in coal preparation plants. The study indicated that flocculants with molecular weights of 12 to 14 million and degree of hydrolysis around 40% gave the best "average" performance over a wide range of process conditions. The pick-up and filtration of fine coal was demonstrated on a pilot scale to be a critical function of flocculant properties. This study also showed that the agitation intensity during flocculation was a critical parameter in determining the settling rate of the slurry and the clarity of the resulting supernatant. An electronic meter to measure agitation intensity was designed, constructed and tested to demonstrate how, for the first time, laboratory results can be implemented in operating plants.

Jan 1, 1989

We operate a 50 cubic metre per hour mobile alluvial tin mine on small scattered deposits in the Irvinebank area. Wash is loaded by a Cat. 950 front end loader into the bin of a screening section and screen undersize is pumped to a separate jig unit. Both units are rubber tyre mounted and are shifted once a month when the haul distance gets to about 150 metres. The shift takes about 8 hours.The screening section is sited close to the face with a ramp for dumping in and a one metre drop for the screen oversize which is removed by the loader.A reciprocating plate feeder with variable rate hydraulic drive, feeds wash onto a horizontal 1.2 metre x 2.2 metre two deck Kinergy screen. Minus 10 millimetre undersize is pumped by a Warman 6/4 sand pump with a 37 kW variable speed Reeves Motordrive to the jig unit.The jigs are placed 20 to 70 metres away so that tailings will run back into previously mined ground. Reject stone is used to impound the sand and mud, allowing the water to filter through and return to the feed water pump.An MTE trapezoidal module is used as a primary jig. Hutch product is pumped to an eight cell clean-up jig which we developed ourselves along MTE lines. It has a trapezoidal shape and sawtooth stroke provided by cams. Clean tin is taken from the first four spigots. These consist of clear plastic tubes fitted with taps so that there is no water loss except when the tin is drawn off. Fine concentrate from the last four spigots is put over a curvilinear table which sits on a steel base packed with earth.

Jan 1, 1986

By F Hungerford

"In-seam drilling has been undertaken for the past 30 years for gas drainage to reduce the risk ofoutburst and lower the concentrations of seam gas in the underground ventilation. The drillingpractices have reflected the standards of the times and have evolved with the development oftechnology and equipment and the needs to provide a safe environment underground. Earlypractice was to adapt equipment from other fields, but with changing emphasis, research anddevelopment by the coal industry has created specifi c equipment, technology and practices toaccurately place in-seam boreholes to provide efficient and effective gas drainage."

Jun 1, 2012

By Weller K. R, Stewart P. S B, Restarick C. J

The performance of the Renison tin concentrator was assessed in detail for two arrangements of the three available ball mills. With two mills used for primary grinding and the third for regrinding table tailing, the concentrator recovered 65.3 per cent of tin in the three tin concentrates produced by tabling, vanning and flotation at a calculated overall grade of 37.5 per cent tin prior to batch dressing. In the second arrangement one mill was used for primary grinding and two mills for separate regrinding of table tailing and sulphide concentrate. The metallurgical effective- ness of the change was somewhat obscured by unintended changes,i.e. an increase in the assay of the fresh feed from 1.38 per cent to 1.1+6 per cent tin and unresolved changes in the sulphide rougher flotation and tabling. However, using the results from a detailed size by size analysis of the behaviour of ore components in appropriate parts of the plant, it proved possible to show that, had the two unintended changes not occurred, up to 5 per cent

Jan 1, 1977

Mssissippi Valley-type (MVT) and sedimentary-exhalative (SEDEX) zinc-lead deposits represent about half to three-quarters of the world's production and reserves of lead and zinc. The two deposit-types have traditionally been regarded as separate entities in terms of genesis largely because they possess very different morphologies, resulting from the epigenetic nature of MVT deposits and the syngenetic origin of SEDEX deposits. Similarities in regional setting, metal ratios, size and grade, lead and sulphur isotopes, and source(s) of fluids and metals in the two deposit-types, however, suggest that they could be products of similar genetic processes. The physical properties of MVT ore fluids suggest that certain types of SEDEX deposits could have been formed from fluids possessing similar salinities and temperatures. The hypothesis is further strengthened by the facts that: 1. in several cases MVT and SEDEX mineralisation occurs in the same region, and 2. recent advances in establishing the timing of MVT mineralisation has revealed that some MVT deposits are contemporaneous with nearby SEDEX deposits. If MVT and SEDEX zinc-lead deposits do indeed share a common ultimate derivation from fluids that emanated from sedimentary basins, then the presence of one deposit-type in a region could be used to infer the possible presence of undetected deposits of the other type. Furthermore, knowledge of the mineralisation age of one type will constrain the exploration target host rocks of the other type. A genetic relationship between MVT and SEDEX mineralisation may also explain why certain individual deposits, such as several in Ireland and eastern Canada, appear to be 'hybrids' and possess geological attributes of both end-member types.

Jan 1, 1993

By Lyman G. J

The volumetric distribution of valuable mineral, or phase, within a set of particles is called the liberation distribution. To optimise a mineral processing plant it is necessary to know the liberation distribution in most of the streams, especially those adjacent to separation devices. Possibly the most common method of analysing ore particles is to section sets of similarly-sized particles. However, the observed sections can appear liberated even if the particle is composite. This means that the 'apparent' liberation distribution can be very different to the 'actual' liberation distribution. This discrepancy is called stereological error. One must then somehow estimate the actual liberation distribution using the apparent liberation distribution. This problem is called the liberation distribution problem and its solution is the subject of this paper. The solution is based on a sorting algorithm which uses geometric probability equations. These equations are based on the assumption that sectioning is isotropic and uniform. Apart from these assumptions the equations are completely independent of particle shape or texture. The algorithm is verified by numerical simulation and experimental methods. For the numerical simulations the correspondence between the actual and estimated liberation distributions is excellent. For the experimental methods, the agreement is not as good and appears to be due to experimental errors.

Jan 1, 1995

By Hochwimmer B, Baxter JL

Heavy minerals are mined from two fossil strandlines on the southern Swan Coastal Plain. The Capel shoreline, 7 km inland, and the Yoganup shoreline, 15 km inland are arcuate, northwest-facing, and remote from the modern coast. Based on foraminiferal and molluscan assemblages, the shorelines are probably of Pliocene age. The Yoganup shoreline is adjacent to the Whicher Scarp, which is cut into the Leederville Formation (Lower Cretaceous) at the southern boundary of the Swan Coastal Plain. Stratigraphic relations and detailed sedimentology have been studied from temporary exposures in the Yoganup Extended and Yoganup North mines, within a strandline complex at 27 m and 18-33 m above sea level respectively. Heavy minerals were deposited in thin, shallowing-upward sequences along a wave-dominated clastic shoreline cut into pre-Cainozoic sediments. Lithofacies units deposited in eolian, foreshore, shoreface and lagoonal environments are the most significant sites of heavy mineral accumulation. The data collected provide a basis for further exploration.

Jan 1, 1986

The Iron Prince orebody occurs within the Lower Middleback Jaspilite Horizon of the Middleback Group and consists of hematite within host rocks of jaspilites and schists. The ore was probably the product of leaching of silica from jaspilites and replacement by iron, concentrations occurring in suitable structural traps. The narrowness and the presence of extensive dolerite amphibolite dykes within the orebody make it essential to operate a grade control programme in advance of the faces. Information from drilling is drawn up on bench plans, step plans and impurity overlays, and these serve both in day to day production planning and in long term planning. Mining is done selectively by open-pit methods and blending conducted by keeping at least three faces of different grades of ore open at any one time. No stock piles of ore are kept for blending, but contact ore, contaminated ore and enriched material are dumped for later beneficiation.

Jan 1, 1971

By Perring CS, Hill RE, Barnes SJ, Vallance SA

The Maggie Hays nickel sulphide deposit is located at latitude 32¦ 15 'S, longitude 120¦ 30' E on the Lake Johnston (SI 51-1) 1:250 000 map sheet. The deposit occurs in the Lake Johnston greenstone belt, in the Southern Cross Province of the Archaean Yilgarn Block, 500 kilometres east of Perth, Western Australia (Figure 1). The remoteness of the Lake Johnston greenstone belt and its poor access, restricted previous exploration activities and the full appreciation of the geology and its Ni-sulphide potential. It was not until 1991, when Forrestania Gold NL commenced exploration activities, that the geology of the ultramafic units and their potential to host significant concentrations of Ni sulphides were clearly established. This paper, which describes the geology and the characteristics of the Maggie Hays deposit, is based on the results of exploration by Forrestania Gold NL and a collaborative research agreement between CSIRO Division of Exploration and Mining and Forrestania Gold as reported by Perring, Barnes and Hill (1994), Perring and Hill (1995), Perring (1995 a and b) and Barnes, Perring and Reilly (1995). A comprehensive description of the geology, petrology and geochemistry of the deposit is being prepared for publication by CSIRO (Pemng, Hill and Barnes, in press).

Jan 1, 1996

By Wood P. D, Pettifer G. R

In the upper coal surface in the Latrobe Valley, craters known locally as fireholes have developed due to prehistoric coal fires. They can be several hundred metres across and up to fifty metres deep, and are now filled with overburden materials varying from hard baked clays to very soft lacustrine clays. In addition to reducing coal reserves, continuous mining operations are seriously affected by fireholes. Large undulations in the upper coal surface result in a mixture of coal and overburden on the upper mining levels. The very soft lacustrine clays are unstable in the mine batters and the overburden dump, are difficult to handle on the bucket wheel excavator/conveyer system, and have insufficient bearing capacity for the large bucket wheel excavators. Early identification is essen- tial and both drilling and dynamic core penetrometer have been exten- sively used. However, this has not proved adequate in locating and defining the extent of all fireholes, due largely to their irregular shape. To overcome this a range of geophysical techniques has been trialled with very promising results. A trial area has been covered on a twenty metre grid using gravity and Geonics EM34 conductivity measurements and the same area has been covered at a closer spacing with high resolution magnetics. Image processing of contoured magnetic, EM34 conductivity and residual gravity data has resulted in very good correlation with drilling data.

Jan 1, 1989

By Demin SS

Slow seismotectonic movements along the in-clined deep fault zone under the compressional horizontal stresses are supposed to be the prin-cipal mechanism controlling the structure and processes in the active ocean margins. Within the scope of the plane strain problem a simple 2-D geomechanical model for the evolution of an island arc system is investigated. We consider a homogeneous elastic half-plane with a shea-ring surface crack. The key element of the model is viscous interaction between the crack sides, the viscisity varying with depth. The model dif-fers from the classical steady-state mode of subduction by nonstationary creep processes on deep faults and by possibly cyclical development of the transition zone.A numerical modeling of the stress-strain state within the island arc system through time was carried out using a semianalytical approach. The results of simulation are in good agreement with geological, geophysical, and seismological data.

Jan 1, 1990

Extraction under very mild conditions - a few minutes at room temperature with poor solvents - yields results characteristic of surface properties for a variety of coals. Such superficial extractions preferentially remove long-chain aliphatic compounds. As coal becomes more oxidized, less of these yellow- colored compounds is extracted, forming the basis for a simple colorimetric test for coal surface quality. The fact that these aliphatic compounds are responsible for surface hydrophobicity is supported by good correlation between extraction results and floatability, which decreases with decreasing extractability. This extraction test is very sensitive to oxi dationb even the effect of heating for an hour at 100 C can be detected. A second extraction test using mild alkali conditions has shown good correlation with plant dewatering Operations.

Jan 1, 1986

By T Mahlangu

The leaching of gold in alkaline aqueous cyanide solutions may be reduced significantly by the passivation of the gold by a surface layer of polymeric aurocyanide. This passivation of the gold is typically countered by the presence of Pb(+2) species in solution, which may be present as an impurity in the solution, or specifically added for this purpose. The speciation and availability of Pb(+2) in typical cyanide leach solutions is illustrated as a function of pH, and the presence of S(-2), S(+6), Cu(+1) and Ag(+1) species. The probable role of the Pb(+2) species in efficient gold leaching is discussed.

Jan 1, 2007

By Savidis GM

This report outlines the experience of Australian mining operators in dealing with large falls of roof in advance of longwall supports. Previous and present techniques used for face stabilisation have been described, together with an analysis of [actors which contributed to the roof falls, in each case. Attention has been focused on the stabilisation technique used at Angus Place Colliery, where the face coal was successfully reinforced by injecting chemical foam into Lite fractured areas. Although considered to be one of the worst roof falls in the history of Australian longwalls (60 m in length and up to 10 in in height), it was subsequently possible to resume cutting in Longwall 9 two weeks after the foam injection. A preliminary schedule of work involving the 'strata replacement' method, is also discussed. It has been based substantially on experience gained with cementitious supports, principally by ACIRL and Monier Resources.

Jan 1, 1986

The winning and upgrading of mineral raw materials necessarily includes size reduction, which serves the liberation and production of marketable products from highly valuable and bulk materials. For crushing, the following factors can be duly accounted for depending on material type and the selection of the suitable machine: ò producing a particular size distribution, ò producing a particular grain shape, ò selective comminution, ò gentle comminution, and ò producing a size range required by a specific process and/or for a specific product.

Jan 1, 1993

By Holliday R, Floyd JM

A laboratory investigation was carried out to determine the distribution of gold between the products of lead-zinc concentrate smelting in the Imperial Smelting Furnace (ISF). Bullion, speiss and slag from the ISF at Cockle Creek were used as the starting materials to evaluate the effect of gold and copper content of products on the distribution of gold between phases under conditions simulating those in the ISF hearth. The ratio of gold in bullion to gold in speiss has a mean value of approximately 1.6 and is independent of the gold content of the bullion. The distribution coefficient of gold between bullion and speiss is dependent on the copper level in speiss and is lowered by increasing copper content in speiss. The ratio of gold in bullion to gold in slag is in the range 25 to 5700 and dependent on the gold content of the bullion. For low gold concentrations in bullion of the order of 1 g/t and a bullion to slag ratio of 1:3 the gold loss to slag is expected to be approx- imately 23%. In all tests the gold in slag remained low, in the range 0.05 to 0.5 ppm provided metal prills were not suspended in Slag.

Jan 1, 1986

Reverse sensitivity is a critical issue for all extractive activities. Extractive industries can only establish in the location of the particular resource sought to be extracted. Avoiding a location near sensitive activities (such as residential activities) may, therefore, be more difficult for extractive industries, than for other industry (such as dairy factories).   This paper focuses on the following matters: +        principles to be derived from case law, +       district and regional council approaches managing reverse sensitivity effects, and +        avoiding, remedying or mitigating reverse sensitivity effects in the future.

Jan 1, 2006

By Lorenzen L

In South Africa, as in many other countries, the young engineering graduate is promoted quite soon to a management position where he uses less technical skills and more people-oriented skills. In the standard undergraduate curriculum for engineering, little attention is paid to the non-technical issues of the profession. An undergraduate course in management techniques cannot be a substitute for a MBA or Masters degree in engineering management, but can at least create an awareness of the practical problems facing the engineering manager. The aim of this paper is to provide an outline of such a course structure at the University of Stellenbosch. A survey is also presented on management training in the South African and Australian mineral industries. Feedback from students and graduates indicates that the fresh graduate does not fully appreciate the value of such a course until he/she achieves a position of responsibility after two or three years. Nevertheless, the management course appears to be successful in widening the perspectives of the engineer. As explained frequently in management journals, the technically oriented person (the engineer) has a convergent thought pattern, which could be in conflict with the more divergent thought pattern of the top, personnel or marketing manager. It becomes increasingly imperative for the young minerals engineer to be externally oriented instead of the traditional internal focus of engineering. The engineer should not only be aware of environmental issues in the technical design and operation of plants, but should also understand the inter-relationship between public relations, political pressures and environmental perceptions vis-d-vis technical facts.

Jan 1, 1993