Search Documents

By P Fuller, A R. Penney

Re-commencement of mining in the Western Zone of Beaconsfield Gold Mine following a seismically-induced rockfall fatality in April 2006 required a change of mining method involving drilling and blasting from specially developed drives in the footwall of the orebody. Broken ore is mucked remotely from ore drives on each level. Support in the footwall drives is required to maintain stability during their development and as stopes are retreated, which increases induced stresses and further seismic events are triggered. The paper outlines the challenges involved and methods used to select the footwall drive support to handle both static and dynamic load demand. The importance of load development in the support system, its displacement capacity, the compatibility of support elements and energy absorption capacity of the support system are highlighted. It is usual in any support selection process to ensure that capacity exceeds demand to create a factor of safety. In this case the demands on the system relate to load, displacement and energy absorption and the support system capacity for each must ensure that appropriate factors of safety for each are achieved. The paper shows how these factors are not independent and that selecting a high factor of safety for load can lead to compatibility problems with support elements in the support system.

Jan 1, 2008

By S Agdaca

Leightons is the sole contractor at the Wahana Coal Mine Project (part of the Bayan Group), a multi-seam thermal deposit consisting of 13 coal seams with thicknesses ranging from 20 cm to 500 cm. The average dip of the deposit is 18 - 20°. However the deposit is heavily faulted in certain domains with anticlinal and synclinal structures present causing seams to dip up to 90°. Average thickness of coal inter-burdens range from less than 2 to 12 m. The minimum coal thickness being mined is 20 cm. Coal production is direct mine mouth feed and there is no coal processing plant currently used.Conventional blasting between the highly variable coal horizons in the early phases of the mine life was suboptimal from a production perspective. Drilling short holes with a reduced drill pattern, and on occasions with sloping benches, resulted in low drilling and explosives loading efficiency.A high frequency of small size blasts fired up to two times daily was required with each blast consisting of four up to five small blast areas. Each blast averaged approximately 36 000 bcm thus causing a low utilisation rate of the mining fleet from frequent blast delays and the inability to deploy larger Liebherr 9350 excavators on bench. It was identified that increasing the production targets required a more efficient drilling and blasting process. Furthermore, due to the highly variable nature of the deposit, the existing coal model was determined to not be able to accurately predict the coal seam location prior to blasthole drilling.In August 2009, Leighton Contractors Indonesia and Orica Mining Services with the full support of the Wahana team, initiated through seam blasting trials using electronic blasting systems. Further trials were conducted in November 2009. Trial evaluations indicated that the benefits from decreased lost time events due to blasting, an increased vertical advance rate per blast, and increased overall blast size could be attained while not damaging or diluting coal.Full-scale?through seam blasting has been ongoing since February 2010 for the upper eight coal seams to extract coal seam thicknesses ranging from 20 - 100 cm. This paper will discuss the parameters of the through seam blasting process in Wahana and the resulting benefits to the overall mine production.

Nov 8, 2011

By S Q. Liu, E Kozan

This paper proposes a new multiresource multistage scheduling problem for optimising the open pit drilling, blasting and excavating operations under equipment capacity constraints. The flow process is analysed based on the real-life data from an Australian iron ore mine site. The objective of the model is to maximise the throughput and minimise the total idle times of equipment at each stage. The following comprehensive mining attributes and constraints have been considered: types of equipment; operating capacities of equipment; ready times of equipment; speeds of equipment; block-sequence-dependent movement times of equipment; equipment-assignment-dependent operation times of blocks; distances between each pair of blocks; due windows of blocks; material properties of blocks; swell factors of blocks; and slope requirements of blocks. It is formulated by mixed integer programming and solved by ILOG-CPLEX optimiser. The proposed model is validated with extensive computational experiments to improve mine production efficiency at the operational level. The model also provides an intelligent decision support tool to account for the availability and usage of equipment units for drilling, blasting and excavating stages.CITATION:Kozan, E and Liu, S Q, 2014. An Open pit multistage mine production scheduling model for drilling, blasting and excavating operations, in Proceedings Orebody Modelling and Strategic Mine Planning Symposium 2014 , pp 329–334 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 24, 2014

By A Black, A de Jo, J Cavanagh, J Harding

Acidic and metal-rich waters have been discharging from Sullivan Mine, West Coast, New Zealand since the closure of the mine during the early- 1990s. This has resulted in a decrease in pH from a background of 4.5 to 2.8 and an increase in metallic elements in nearby Rapid Stream. In addition to the chemical effects on Rapid Stream, a study of freshwater macro-invertebrates revealed the absence of most biota downstream from the discharge. An attempt is being made to use the Sullivan Mine as a case study of problem and remediation analysis.

Jan 1, 2003

By Y Ren

The algorithms employed by the commercial tools are either heuristic algorithm or iterative optimisation of a subsystem. This often results in a suboptimal schedule. In this paper, the author presents a new scheduling algorithm that incorporates with a novel stockpile configuration system, an improved algorithm on multiple processes and a mixed-integer linear programming (MILP) global optimisation model. It can simultaneously optimise stockpiles, blending, multiple processes as well as multiple mines. In addition, it allows the user to interact with the solution to adjust the solution to be practical and desirable.CITATION:Ren, Y, 2013. A simultaneous optimisation tool for open pit mine scheduling, in Proceedings World Gold 2013 , pp 427-432 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 26, 2013

By M Bond, R R. Hargreaves, G W. Booth

There are numerous causes of speculative mineral resource and reserve inflation. Traditionally, these are linked to issues of data accuracy or misinterpretation, the use of overly optimistic estimation parameters or assumptions, an absence of independent expert verification, or the simple pressure to increase company value, covert or otherwise. Owing to its subjective nature, classification of resources and reserves remains an opaque process. Of necessity, Competent Persons rely on personal heuristic interpretations, ideally underpinned by appropriate estimation and classification experience across commodity and deposit types. Whereas independent verification of individual resource and reserve statements remains impractical, publicly available data can be interrogated for potential category inflation, particularly when viewed with exploration expenditure statistics included in annual company reports. Abrupt changes in category tonnages and market capitalisation without concomitant expenditure can aid in outlier detection. Consequently, a comparison of common exploration and resource reporting parameters offers a basis for risk assessing classification robustness, over time. In this introductory study, an analysis of globally listed companies was undertaken over a multi-year period, examining base and precious metal projects in both preproduction and operational asset classes. From these, a series of exploratory decision tree trigger points were generated against which target companies were anonymously identified and risk-ranked.

May 24, 2023

By D Craw, P V. Angus

Gold mineralisation at Macraes occurs as late quartz-carbonate veins within a body of sheared and hydrothermally altered Otago Schist, the Intrashear Schist. The alteration is characterised by the presence of rutile and the absence of epidote and titanite, indicative of an alteration fluid containing >10 mol per cent CO2. In areas of high strain, a fabric of black microshears develops, gradational to mylonitic cataclasite in the high strain zone adjacent to the hanging wall of the duplex shear zone. The microshears contain hydrothermal graphite, inferred to have been deposited from a methane-rich fluid. The mylonitic cataclasite is characterised by abundant pyrite, the absence of albite and extreme grain size reduction. Gold recovery in the CIL processing plant at Macraes can drop to 50 per cent or lower for some unfavourable ore types. Preg-robbing by a component in the ore, possibly graphite, was suspected as the cause. Mylonitic cataclasite was identified as the lithology responsible for the poor recoveries, with the capacity to bind about 30 ppm of gold in the leach tanks. A program of detailed geochemistry and quantitative grain-size measurement using Coulter analysis was undertaken to identify specific mineralogical factors associated with preg-robbing. The results indicate that pyrite, graphite, and extreme grain-size reduction are the factors associated with highly preg-robbing ores at Macraes. The evolution of the mylonitic cataclasite is accompanied by strong potassium enrichment, as muscovite, and depletion in sodium as albite is removed. This suggests that a simple powder XRD ratio of the albite to illite peaks would suffice to distinguish the preg-robbing ore for grade-control purposes.

Jan 1, 1999

By A P. Wibowo

Indonesia holds a significant role in the utilisation of coal resources in the world. Although the number of Indonesian coal resources and reserves do not fall into the world’s top ten, according to 2009 statistics, Indonesia is the seventh largest producer of coal with a production of 256 Mt. More than 80 per cent of this amount is sold in the export market, making Indonesia the world’s second largest coal exporter. Most of the exported coal from Indonesia is used to fulfil the needs of the Pacific market, such as Japan, Taiwan, China, among others. It is also possible to reach the Atlantic market.Along with Indonesia’s development program, until 2025 the Indonesian government has adopted a National Energy Policy that aims to reduce the role of petroleum in electricity generation and replacing it with coal. As a follow-up of the policy, since 2009 PT PLN, the state electricity company has built steam power plants throughout Indonesia as an implementation of the first stage of the Electrical Acceleration Project with a capacity of 10 000 MW. Moving forward, in 2011 PT PLN will also build the second stage of the project with a capacity of 10 000 MW. As a result of the program, the domestic need for coal is expected to increase as much as 44.8 Mt.With the increase in domestic need and decrease in the number of reserves, the Indonesian government has adopted policies to secure the domestic coal supply. A policy that may potentially be adopted by the government is the limiting of coal production, seeing the high rate of increase in Indonesian coal production. The adoption of such a policy will change the distribution map of coal in the Pacific market. Thus, this paper will evaluate the change of coal distribution patterns in the Pacific market along with the increase in Indonesian domestic needs and Indonesian adoption of policies regarding the securing of coal supplies.

Nov 22, 2011

By M I. Pownceby, N Karimian, A Frierdich

These may be found with goethite through mechanisms including direct substitution or coprecipitation of nanocrystalline phases. Understanding P incorporation in goethite has significant implications for Australia’s iron ore industry as it lowers their commodity value. The current study tests a novel low-temperature technique to extract P impurities from synthetic goethite phases under O2-free ambient conditions by utilising Fe(II)-catalysed recrystallisation. The objective of this study was to examine the effect of the Fe(II)-catalysed recrystallisation of goethite on the geochemical behaviour (mobility and speciation) of co-associated P. To achieve this, we tracked changes in labile P (aqueous and 1M NaOH extractable) concentrations over time in goethite suspensions which were reacted with Fe(II)aq for 14 days under circumneutral pH conditions and room temperature conditions. Temporal changes in Fe mineralogy were investigated via synchrotron-based X-ray absorption spectroscopy. Iron K-edge extended X-ray absorption fine structure (EXAFS) spectroscopy confirmed goethite as the only mineral phase in P-free treatments while goethite (~86 per cent) and feroxyhyte (~14 per cent) were the main phases in 1.0 per cent P-containing treatments after a 14- day reaction with Fe(II)aq. According to our findings, the treatment of P-goethite with Fe(II) for a duration of 7–14 days, followed by a 24-hour extraction of the reacted solids using 1M NaOH, results in the removal of approximately 79.5 per cent of the initial P content. This removal encompasses both the aqueous fraction (~4.5 per cent) and the surface adsorbed fraction (~75 per cent) from the 1 per cent P-bearing mineral phase. Notably, this approach demonstrates an improvement in P extractability, with approximately a 10 per cent increase compared to the 1 per cent P-goethite sample that was not reacted with Fe(II).

Sep 18, 2023

By B Prasad, M P. Roy, P K. Singh, C Drebenstedt

Blasting operations play a pivotal role in the overall economics of opencast mines. The blasting subsystem affects all the other associated subsystems, ie loading, transport, crushing and milling operations. Fragmentation control through effective blast design and its effect on productivity is a challenging job for the practicing blasting engineer due to inadequate knowledge of actual explosive energy released in the borehole, effect of varying initiation practice in blast design and its effect on explosive energy release characteristic. This paper describes the result of a systematic study on the impact of blast design parameters on rock fragmentation at two mines in India. Both the mines use draglines and shovel-dumper combination for removal of overburden. Despite its pivotal role in controlling the overall economics of a mining operation, the expected blasting performance is often judged almost exclusively on the basis of poorly defined parameters such as powder factor and is often qualitative, which results in a very subjective assessment of blasting performance. Such an approach is a very poor substitute for accurate assessment of explosive and blasting performance. Forty-seven blasts were conducted with varying blast designs and charging patterns and their impact on the rock fragmentation are documented. A high-speed camera was deployed to record the detonation sequences of the blasts. The efficiency of the loading machines was also correlated with the mean fragment size obtained from the fragmentation analyses.CITATION:Singh, P K, Roy, M P, Drebenstedt, C and Prasad, B, 2015. Blast design parameters and their impact on rock fragmentation, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 755–762 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By H A. Linn, K Winn, C W. Lee

The Q-slope method for rock slope engineering was developed to enable engineering geologists and rock engineers to rapidly assess the stability of excavated rock slopes in the field and make optimal adjustments to slope angles as rock mass conditions become apparent during construction of road cuts or benches. An empirical relationship between Q-slope and long-term stable slope angle is now supported through over 500 cases studies from Asia, Australia, the Americas and Europe. This paper presents about the stability analysis by first-ever applying Q-slope method on abandoned quarry wall in Singapore. The 30 m high rock slope which is composed of monzogranite rock was severely damaged by blasting operation. As the rock slope is intended for public view the objective was to retain the natural outlook and without any artificial support application thus manual scaling was carried out to clear the loosed rock blocks. In the end stable slope angle of clean rock face is determined once again by Q-slope method.

Nov 29, 2022

By K Dudley, D Readett

The design of entrainment control processes in copper SX plants has been studied by use of models based on achievable plant performance. A number of alternatives have been assessed for their suitability in minimising the transfer of deleterious species from PLS into the electrolyte. The position of the wash (scrub) stage in the circuit, either before or after the loaded organic tank, has been the subject of considerable debate. The modelling shows that at ænormalÆ entrainment levels, the performance of the circuits are very similar. However at high entrainment levels the selection of the wash after the loaded organic storage has significantly lower transfer of contaminants. When considering the inclusion of a loaded organic coalescer the results of the modelling again show that the best circuit has the loaded organic storage/coalescer before the wash stage. The overall control of EW contaminants includes both a wash stage and an EW bleed flow. The total water use for these two flows is shown to go through an absolute minimum. The minimum flow rate is not greatly dependant on the total entrainment from the SX settlers. This can be a useful operating strategy if the quantity of high quality water for make up is limited by the capacity of the water treatment plant (eg RO). However the minimum cost option is to maximise the flow of water to the wash stage and minimise the EW bleed stream. The main driver for this is the cost of the cobalt sulphate contained in the electrolyte. Some results from the latest circuit modifications at the Nifty and Girilambone Copper Projects are presented to confirm the benefits of using both coalescing systems and a wash stage. The EW bleed has been reduced to a level that is less than the loss internally in the SX stage to stage entrainment. There has been an occasional need to add chloride to the EW to maintain sufficient concentration to act as a growth modifier.

Jan 1, 2002

By B Wu, B W. Lei, B J. Duan

When a coalmine fire occurs, it is crucial to judge the developing trends inside the fire area by analysing the changes of gas concentration in order to formulate the proper rescue measures. At present, few researchers have focused on the relationship between the changing trend of gas product and basic characteristics of fire in the coal fire extinguishing process. To study the relationship of basic characteristics of coalmine fire during the extinguishing process, an experimental platform for coal combustion in a confined space was built, and gas production, flame image and coal temperature during the extinguishing process were monitored and analysed by an online continuous gas analysis instrument, camera and thermocouple. Research shows that during the burning phase of the coal sample in the confined space, the flame zone decreases gradually due to insufficient gas supply. The size of the flame zone fluctuates and shares a positive correlation with CO concentration, while sharing a negative correlation with O2 and CO2 concentrations. Then, in the extinguishing phase, the increasing rate of CO2 concentration and the decreasing rate of O2 concentration both decrease gradually, but CO concentration would rise for a period before it eventually decreases. Coal temperature continues to rise in the open flame stage and does not go down until the flame is extinguished.CITATION:Lei, B W, Wu, B and Duan, B J, 2015. Experimental study on extinguishing characteristics of coal fire in confined space, in Proceedings The Australian Mine Ventilation Conference, pp 279–284 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 31, 2015

By G M. Zhomin, A S. Arkhipin, A Kondratiev

Viscosity of multicomponent slags is one of the crucial physicochemical properties for many industrial processes and technologies. While the viscosity-temperature relationship of completely molten slags can well be described by an Arrhenian-type law, the compositional dependence of viscosity is still not fully understood, especially in compositional regions with the lack of experimental data (eg at the glass-former concentration of 90 molar per cent or higher). In the present work major compositional relationships of the activation energy of viscous flow have been revised for numerous binary and ternary slag systems on the basis of experimental data collected and stored in the viscosity database OxiVis. For example, it has been found that the activation energy relevant to the polymerisation effect in binary systems of the MO-GFO type, where MO is the modifier oxide (ie monovalent K2O, Na2O, Li2O and bivalent CaO, MgO, BaO, MnO, PbO etc) and GFO is the glass-forming oxide (SiO2 or B2O3) is not always proportional to the third power of XGFO (contrary to the Urbain formalism) and can vary significantly dependent on the slag system. Also, the activation energy of the charge compensation effect has been revised for ternary systems of the AO-MO-GFO and AO-MO type, where AO is the amphoteric oxide (Al2O3, Fe2O3 or other). A simple polynomial model has been proposed on the basis of the carried-out analysis for estimation of viscosities of multicomponent slag systems. The model has been optimised against the experimental viscosities in the selected binary, ternary, and higher-order oxide systems and has been shown reasonable agreement with the experimental data.

Aug 21, 2024

By O Joneydi, J Viljoen, R Funnell

Computational Fluid Dynamics (CFD) modelling is a useful tool that can assist engineers in designing effective ventilation systems for the control of airborne dust generated during mining operations. Thistechnology can save time, effort and the costs associated with re-work or the traditional on-site experimental field trials by running desktop 3D simulations of the various proposed scenarios using state-of-the-art CFD analysis tools. Before implementing a dust management system, an understanding of the behaviour of airborne dust particles in the face zone can be achieved, which can improve the confidence in the secondary ventilation and dust management design. Usingadvanced numerical models, suitable dust extraction strategies can be foreseen, and multiple scenarios can be simulated and investigated quickly. As a case study, dry drilling operations in Kimberlite orebodies produce large quantities of fine dust which poses health and safety risks. An effective dust management system is required to achieve acceptable face conditions. A possible practical solution is a ducted exhaust ventilation system with a force fan in the face zone. This paper demonstrates how CFD analysis can be used as a tool to assist the design engineer with validating and optimising the proposed ventilation design by tracking the trajectories of different size dust particles, to determine the best equipment layout and appropriate flow rates which minimises airborne dust.

Oct 12, 2022

By Fickera M. A, Marshall S, Burgeese F. L, Burgees J, Estrina H

A new high intensity flotation process FASTFLOT was deployed to recover residual zinc from the zinc circuit tailings at Pasminco Mining's Concentrator, Broken Hill. Performance of the FASTFLOT process is discussed with respect to various size fractions. Results suggest that the process has an affinity not only for fine particles but also for +200 ¦m particles which the conventional flotation cells failed to recover. Various strategies for FASTFLOT deployment are also discussed.

Jan 1, 1995

By G Brewster

The Eagle on the Hill tunnels form part of an upgrade of Mt Barker Road, 15 km to the southeast of Adelaide. The upgrade significantly improves safety and reduces delays on this major road, which winds steeply through mountainous terrain. The twin tunnels each spanning 15 metres run in parallel for a length of 480 metres. The tunnels are excavated in slightly weathered high strength slates and very high strength quartzites of the Saddleworth Formation on the western margin of the Mount Lofty Ranges. Steeply dipping slate cleavages and the high fracture ratio result in many slope stability problems in the project area. The level of geotechnical investigation undertaken prior to the calling of tenders for the project was extensive. This included the excavation of a pilot tunnel along one of the tunnel alignments, which allowed accurate mapping and rating of the rock, resulting in an increased level of confidence during the tender process. One of the features of the winning alternative tender design was the use of canopy tubes, flexible steel ribs and shotcrete to replace up to 40 metres of deep portal cuts in unstable rock with driven tunnels. Slope stability issues were overcome with the use of rock dowels and shotcrete. The support concept allowed the safe driving of the tunnel portals with as little as two metres of overburden. The design incorporated lining drainage and criteria for fireproofing based on European experience to ensure the ability of the tunnels to remain stable in the case of a severe fire incident. The support design allowed for maximum flexibility with a range of support types able to deal with the varying ground conditions. Design development and support refinement continued throughout the tunnel construction phase with close liaison between the designer and the constructor. Monitoring and review of feedback from the construction site by the Sydney based design team was easily achieved by means of electronic transfer of photographic and survey information, telephone and fax communication and regular site visits. The contractor for this project is Macmahon Concrete Constructions Joint Venture (MCCJV) and the designer is Connell Wagner. Excavation commenced in January 1998 with tunnel breakthrough having been achieved in early-August 1998 and mid-September 1998 respectively. Concrete lining construction is scheduled for completion in April 1999.

Jan 1, 1999

Limnological processes are often overlooked when trying to assess the long-term water quality of pit lakes. It is essential to deal with these aspects, since they determine the geochemical and redox conditions around the submerged reactive rocks. Underground mining at East Sullivan (northwestern Quebec, Canada) stopped in 1966. Two adjacent stopes, 91 and 106 m deep, were left open to the surface, with roughly circular apertures of about 7700 and 18 000 m2. Water filling of the two glory holes went on over three decades and overflow began in 1999. Surface water pHs values were near neutrality as late as 1994 (6.3 - 7.0) but had become acidic by 1999 (2.6 - 3.5). Limnological processes were investigated in late-1999 and early-2000, with temperature measurements at 1 m intervals and sampling of the water columns before and after the late fall density inversions. A strong chemocline-thermocline was observed at 15 m. Above the chemocline, the water had low pH (3.2), no alkalinity, and low Na, Ca and sulfate. Below the chemocline, the concentrations of these parameters and the pH increased, with pH at 5.5 - 6. Consistent with the low pH values present in the upper 15 m, the concentrations of Al, Cd, Cu, and Zn were high near surface, and decreased below the chemocline. Dissolved oxygen concentrations as well as Eh decreased with increasing depth. Alkalinity integrated over the entire water column below the chemocline was at least six times larger than the acidity inferred from Fe2+ and Fe3+ concentrations. The temperature survey showed that seasonal density inversions do occur in the water column. The inversions do not involve the entire water body, since the surface to depth ratio is too small for a complete overturn. Oxygen from surface waters is carried to the bottom where it oxidises sulfides, until its depletion. Residual Fe2+, stable under anoxic conditions, is displaced upward by the next dense water incursion. It eventually reaches the thermocline, but only after many successive incursions. There, its oxidation to Fe3+ allows hydrolysis, which consumes dissolved and wall-rock alkalinity. It is only in 1999 that alkalinity was finally exhausted and that the pH shifts to acid values. The low pHs in the surface waters allow a build up of Fe3+ and Al3+, and desorption of metals from colloids. Buffering is assumed to be controlled by wall-rock oxyhydroxides in surface waters, and by carbonate minerals in the bottom waters. Because the seasonal overturns are far from being complete, the large amounts of alkalinity acquired from the wall-rock in the bottom waters cannot balance the acidity of near surface waters. Hence the surface water is acidic.

Jan 1, 2003

By J H. Park, R R. Kim, H S. Park, H J. Kim

This study focuses on the recovery of valuable metals, specifically silver (Ag) and palladium (Pd), from copper-containing sludge (with copper content less than 20 per cent) generated during PCB processing and from spent petrochemical catalysts used in vapour decomposition during oil refining processes. The present results indicate that an increase in the mixing ratio of alumina-based spent catalyst leads to a decrease in the recovery rate of Ag and Pd. The recovery rates for Ag and Pd range from 84 per cent to 96 per cent and 80 per cent to 98 per cent, respectively. This trend is attributed to the increased emulsification of copper droplets containing Ag and Pd in the slag. The emulsification is caused by the decrease in the settling velocity of the copper droplets due to the increased viscosity of the slag as well as by the decrease in the slag-metal interfacial tension due to an increase in sulfur content at higher mixing ratio of spent catalyst.

Jun 19, 2024

By M Nehring, M Kizil, P Knights, A Mousavi, F Sotoudeh

A cut-off grade is used to distinguish an economically viable block of ore from non-economical ones in mining operations. In order to obtain a high Net Present Value (NPV), a strategic and precise determination of cut-off grades (mill feed/marginal, marginal/waste) is required. In recent years, the significant depletion of feed grades and increasing mining operating costs have affected the viability of new and existing mining operations. Hence, the introduction of a pre-concentration system to process ore before sending it the main processing plant has gained increasing attention for its potential improvements in resource exploitation processes, mineral processing, energy consumption and environmental impacts. The primary potential advantage of implementing a pre-concentration system is the improvement of resource utilisation and increased reserves as a result of a reduction in cut-off grade. The objective of this paper is to present a new cut-off grade method, which can be used in the presence of a pre-concentration system for underground metalliferous mining operations. The results of this study illustrate the potential economic benefits of using a pre-concertation system prior to a mineral processing operation as a result of the reduced cut-off grade and increased NPV.

Nov 10, 2020