Search Documents

By Kazis JV

The beneficiation of fine coal has been the major problem facing the coal preparation engineer in recent years. The influence of clay slime, particle size and reagent type are but a few of the many factors that affect the recovery of fine coal. Laboratory test work has indicated that substantial increases in recovery could be achieved by improvements in technology in all these areas. Unfortunately, in most cases this technology has not carried through to the operating plants.

Jan 1, 1984

The Elura Orebody consists of a number of parallel, vertically oriented pipe-like structures of pyrite-sphalerite-galena mineralization located at the core of a structural dome. Concentric zoning of the mineralization into an outer Siliceous, intermediate Pyritic and inner Pyrrhotitic Zone has been previously recognized and is used in routine geologic modelling of the lead, zinc and silver grades.Statistical analysis of the metal grade distribution in the orebody has confirmed the importance of the mineralogical zones in the understanding of grade trends. The gradational nature of intra-zone boundaries, especially those related to the subjective definition of the Siliceous Zone, are apparent in the statistics.

Jan 1, 1990

This paper reviews the development and operation of a small underground tin mine in NE Tasmania. Tin mineralisation was discovered in the Lottah area in the 1880's with early alluvial and eluvial workings leading to the development of large low grade open pit operations. Apart from short lived activities operations ceased in 1915. Intensive exploration in 1978-81 outlined substantial tonnages of low grade tin mineralisation (0.2% Sn) of open pit material. An underground ore body was also located (800 000 tonnes 0.6% Sn). Spectrum Resources Australia Pty Limited acquired a 98 percent interest in the property in 1988. Mine and mill development began in early 1989 based on an underground mine utilising trackless mining using room and pillar with fill stoping. The milling circuit involves primary jaw crushing, Barmac secondary crushing to lmm, Mogensen and DSM screens with jigs and tables to make a wet concentrate. Final tin concentrates are produced by high tension and magnetic separation. Planned production rates are 500 t/day with a mine life of 6-7 years.

Jan 1, 1990

By Ruston R

When coal mining first commenced in Australia, the principle objective was low cost production with development directed toward recovery of 'easy' coal. Future expans- ion of these early mines into major under- ground operations was neither envisaged nor planned. As the demand for coal grew, these mines were expanded to increase output. however, the absence of initial ventilation planning brought about ad hoc systems wh;ch required continual repair and upgrading. These systems proved satisfactory in the short term because the majority of undergrouni coal mining operations were carried out at relatively shallow depths where gas emission rates were low. By comparison, coal is now being won at depths exceeding 500 metres with a corresponding increase in gas flow from the working seams and adjacent strata. The following paper addresses, firstly, the planning and institution of a ventilation system in a mine where previous inefficiencies were many, and secondly, the value of pre- planning a mine ventilation system in the early stages of mine development, and the need to continually review and upgrade the plan to account for unforeseen ^hanges.

Jan 1, 1983

By Woodhouse M, Drew GJ, Andrews DL

The Honeymoon nickel sulphide deposits are located 45 km south of Wiluna in the 2.7 Ga old Agnew-Wiluna greenstone belt in the NE of the Yilgarn Craton (Figure 1). Both disseminated and massive nickel sulphide deposits are present within the deformed and metamorphosed Honeymoon Well ultramafic complex and are hosted by distinctly different komatiitic lithologies (Gole et al, 1996). The deposit styles and host rock lithologies reflect formation in markedly different volcanic settings. Metasomatism has affected parts of the ultramafic complex, including sections of the sulphide deposits, and has had a marked impact on mineralogy and bulk sulphide compositions. The present indicated resource is 158 Mt at 0.71 per cent Ni in four deposits (0.4 per cent Ni cut-off, resources above 300 m depth, December 1995). This includes a massive sulphide resource of 2.5 Mt at 3.36 per cent Ni.

Jan 1, 1996

The economic significance of a fundamental understanding of the mineral pyrrhotite is dis- cussed. Particular emphasis is placed on the relationship of other sulphide minerals to the pyrrhotite when it is the major sulphide mineral present in an ore body. Studies of the Kambalda nickel deposit are used to give a better under- standing of (a) the genesis and other character- istics of a particular ore body (b) the textural relationships between pyrrhotite and other sul- phide minerals (c) magnetic properties of natural pyrrhotite, and (e) the oxidation and supergene processes that take place in a sulphide ore body.

Jan 1, 1972

By Clements R. J, Davey J. M

Development of the process from the pilot stage to the current operation of the Capel, W.A. plant is briefly described. The design criteria for a larger sized plant are discussed together with factors that relate suitable feedstocks and coal types to the capital cost, capacity and product grade of future plants at locations other than Capel. The application of the process to the direct reduction of iron ores is briefly discussed including its commercial application at Rockwood, Tennessee.

Jan 1, 1979

By C Laming, S Staude, D Hammond, S Sheppard, J Griffith, S Stanfield, S Marriott

Long Operations is located on the eastern slope of the Kambalda Dome in Western Australia. Kambalda hosts nickel deposits that are modelled to have formed from an exsolving sulfide melt from a parental komatiite melt. The nickel deposit model predicts a stratigraphical relationship where massive Fe-Ni-Cu-sulfides are deposited in troughs at the base of komatiite channels. The basal contact of the sulfides is generally tholeiitic basalt. The Kambalda geological sequence form a dome structure with a granodioritic core and have undergone tectonic and metamorphic overprinting, resulting in the formation of upper greenschist to lower amphibolite-facies units.On the basalt-ultramafic contact, within the Long Operations, there are two separate channels hosting seven different orebodies. The Moran orebody is the most undisturbed orebody at Long Operations, with many primary magmatic textures preserved, making it ideal for studies to improve the existing nickel sulfide formation model. Detailed exploration and production infill drilling and systematic sampling indicates consistent nickel tenor variations over the entire Moran orebody. This was also observed in other deposits in Western Australia and was explained as metamorphic variations. Similar variations are observed with some trace elements that cannot be explained by metamorphic overprint but with gravitational segregation in the liquid sulfide. Other more complex trace element patterns (eg Cr) require additional explanations and are partly originated from incorporation of underlain basalt and sediment and partly from gravitational segregation.From a mining perspective, the Moran orebody can be used as an example of modern high-speed mining, but at the same time preserving samples for the future and allowing knowledge from the geological context and geochemical signatures to improve future exploration.CITATION:Staude, S, Marriott, S, Griffith, J, Laming, C, Hammond, D, Stanfield, S and Sheppard, S, 2014. Improvement of existing ore-forming models due to systematic sampling during mining – an example from Kambalda, Western Australia, in Proceedings Ninth International Mining Geology Conference 2014 , pp 341–348 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 18, 2014

Thank you chairman, good afternoon ladies and gentlemen. In my talk this afternoon I intend to cover a brief history, some of the recent experiences and an overview of the McArthur River project.If we consider the themes of this forum, Obstacles and Opportunities, I can confidently say that in attempting to develop the McArthur River deposit Mount Isa Mines Limited (MIM) must have encountered almost every obstacle that can be imagined. However the large size and the high grade of the deposit has ensured an opportunity, from which it is very difficult to walk away from.The McArthur River Here's Your Chance (HYC) Deposit is located in the Northern Territory of Australia. It was discovered by Mount Isa Mines Limited geologists in 1955 and is one of the largest known sedimentary stratiform zinc-lead-silver deposits. The deposit has been the subject of numerous investigations and considerable expenditure culminating in a major feasibility study in 1979. There were a number of factors which prevented development, these being the size of the project, the fine grained mineralization, geographical location, market, social and capital cost. The latter had been estimated in the 1979 study to be $800 million at that time.

Jan 1, 1993

In 1980 Pancontinental Mining Limited decided that while the Jabiluka uranium project was still a major focus of the company's efforts some diversification was necessary. At this time it was decided to include precious metals in Pancon's exploration and acquisition objectives. As a result the now Paddington Gold tenements were acquired, explored and developed. Today, it rates as the 6th largest gold mine in Australia and at an expanded throughput of 1.2 million tonnes per year of ore it will produce about 110,000 ozs of gold per year. Following extensive exploration activities by Pancon's Exploration Division the Operations Division continued with development drilling finally proving up a reserve of about 8.4 million tonnes at an average grade of 3.2 g/t. An in- house preliminary feasibility study was followed by a two phase feasibility study by Davy McKee. This resulted in a recommendation to the Pancon Board of Directors to develop Paddington with an annual throughput capacity of 875,000 tonnes. This paper describes the acquisition, exploration and development of the Paddington project. It goes on to

Jan 1, 1986

By Marshall GA, Dickerson AW

The efficient operation of large haul trucks in large open pit mines requires an economic trade off between the haul route quality, the haul truck payloads and the level of haul truck reliability. This paper describes an investigation into the relation- ship between haul route surface quality and the level of structural reliability of a haul truck main frame. An instrumentation system for unattended recording of data on a haul truck operating normally in a mine and com- puter based analytical procedures were developed and used to identify which road segments contribute significantly to fatigue cracking at various sections of a haul truck main frame. INTRODUCTION In many open pit mines there is exten- sive use of large haul trucks to move over- burden and minerals. In most open pit hard rock mines, both the overburden and mineral ore are moved by large rear dump type haul trucks. Similar haul trucks are also widely used for coal overburden and mine site coal haulage operations in New South Wales, South Australia and Western Australia. Large bottom

Jan 1, 1982

By G Noonan, S Thomas, M Limbert

Stuck drill rods (often referred to as bogged rods) in production ‘upholes’ are a common problem in the underground mining industry. Bogged and broken off drill rods have the potential to fall out of the hole without warning, posing a serious hazard to personnel and equipment below.Current industry practice to alleviate this hazard can be to either grout the hole in order to lock the drill rods in place, or to ‘plate over’ the hole with a rock bolt. Each of these operations seriously delays mine production as both require demobilisation of the production drill and mobilisation of alternative personnel and equipment to address the hazard. Both methods have been assessed for safety and efficiency and were found to be expensive, time consuming and in the case of plating over, ineffective.To address the safety and efficiency short-comings of the traditional practices, the long hole plug (LHP) has been developed to safely secure the lost rods in the hole. The LHP when struck by falling drill rods behaves similar to an expansion shell anchor transferring the axial forces from the falling drill rods horizontally into the rock mass. It is installed using standard production drills allowing work to safely continue with little interruption.Extensive testing has been carried out on the LHP in the laboratory and underground at the Rosebery mine on the west coast of Tasmania, Australia. Testing has included static pull testing, full scale drop testing and underground trials.The outcome of this work has proven the LHPs ability to add safety, volume and cost benefits to the Rosebery underground operation and it is currently in use at that site. It enables proven elimination of a common workplace hazard immediately, thus eliminating delay on the mine’s production cycle.CITATION:Thomas, S, Noonan, G and Limbert, M, 2017. Long hole plug – addressing the hazard of bogged rods in ‘upholes’, in Proceedings 13th AusIMM Underground Operators’ Conference 2017, pp 305–310 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 16, 2017

By Dugan K. J

Mine operators are currently in a situation where market forces are acting to reduce profit margins and at the same time, regulatory bodies are insisting on improved mine safety and stability. This means that ground support must be made more cost efficient while maximising operator and equipment safety.A key aspect of ground support efficiency is the 'in the ground' performance. This paper discusses the factors that influence the way rock bolts and cable bolts perform. It highlights the need to know how support efficiency varies in different ground conditions.

Jan 1, 1992

By Wright G. A

The objective of refining in steelmaking is to reduce the concentration of impurity atoms, e.g. sulphur, phosphorus, from an initially high level to a specified low concentration. A two-film theory of refining is presented in which the rate of

Jan 1, 1980

By Callinan AN

Broken Hill Proprietary Company Limited have recently commissioned a 14 Megawatt power station adjacent to its underground coal mining operation at Appin NSW. The power station is fuelled by methane gas extracted from the coal seams 500 metres below the surface. The methane is compressed and cooled prior to its injection into the combustor of a single shaft gas turbine. The turbine is coupled through a reduction gearbox to an alternator. There is sufficient power generated to cover colliery load, with any excess being exported to Prospect County Council, which is the supply authority for the south western region of Sydney.

Jan 1, 1987

The Douglas mineral sands deposit is located 75 km north of Hamilton in western Victoria, Australia. The deposit was discovered in the late 1990s by Basin Minerals Limited and purchased by Iluka Resources Ltd in 2002. Prestrip mining commenced in December 2004, with ore mining commencing in August 2005. Douglas is the first of several projects being implemented by Iluka Resources Ltd in the Murray Basin, with all heavy mineral concentrate planned to be treated at the companyÆs mineral separation plant in Hamilton. The mineralisation at Douglas lies along the south-eastern margin of the Murray Basin. It is hosted by marine Pliocene Loxton-Parilla Sands and consists of three discrete deposits; Bondi Main, Bondi West and Bondi East. The mineralised sediments dip at a low angle to the west and lie unconformably beneath a veneer of top soil (50 - 100 mm) and subsoil (up to 600 mm) and between three to 12 m of overburden. The barren overburden, characterised by high clay content (<53 ¦m material) generally provides a stark contrast to the sandy ore, which is between 1 m (parts of Bondi East) and 15 m (Bondi Main) thick. Both overburden and ore are removed utilising standard dry mining techniques using both scraper-bulldozer and truck-excavator combinations. All ore is delivered to run-of-mine (ROM) stockpiles before being reclaimed by front end loader into the processing plant. Grade control at Douglas is based around visual dig control aided by high precision survey, which enables accurate reference to the resource drilling and block model data. Vertical excavator faces, inclined scraper faces plus regular test pits and trenches provide opportunities for in pit mapping and sampling. This data is used to refine not only the resource estimate for Douglas but also the drilling, interpretation and resource modelling methods used for similar deposits across the basin. The foundations of the geological reconciliation process at Douglas are the in pit surveys undertaken each time the mining fleet has completed building a ROM stockpile. These surveys and the subsequent interrogation of resource models enable robust estimations of the heavy mineral content of the stockpiles, which are subsequently used to predict the daily input grades into the plant during their reclamation. Reconciliation of this daily data is then undertaken at the end of each month against metallurgical production data and plant balances. Learnings and results from the reconciliation process are used to further refine subsequent resource models and modelling methods.

Jan 1, 2009

By Beattie T. A

The ability of explosives to fragment rock has been assessed in small scale trials at the Granite Rock quarry, Baimsdale, Victoria. Three 65 mm diameter holes were fired simultaneously in a five metre bench, and the rock collected, screened and weighed. The mass of fines increased as the explosive strength increased in the series 30(10 ANFOPS

Jan 1, 1990

By Wilkins L. G

Ore recovered by North Broken Hill Limited as a result of mining operations at its Broken Hill leases is obtained, at the present scale of working, in the proportions of 80% from the North mine and 20% from the British mine sections, and is composed mainly of a silver bearing, sulphide lead and zinc mineral, in association with the gangue materials mentioned later in the text.The lead-zinc sulphide lode at the North mine is deposited in folds in pre-Cambrian sedimentary schists. These folds pitch north-east at approximately 40° and dip north-west at approximately 60°. In plan the deposit appears as two lenses designated on the mine as the "Southern" and "Northern" ore-bodies.The Southern ore-body yields the main tonnage of crude ore. The sulphide mass here overlies a heavy layer of rhodonite which persists with the pitch of the lode. In the central section of this ore-body the sulphide zone is coarse grained and of high grade with a wide range of minerals in the gangue dilution. Quartz, garnet, ftuorite, rhodonite, and felspar are common, whilst chalcopyrites, pyrites, pyrrhotite and green felspar are often present. The Northern ore-body is dolomitic to siliceous in nature. Crude ore obtained from the British section is predominantly...

Jan 1, 1940

By Shoobridge PH

Operating difficulties during 1977 with the Imperial Smelting Furnace operated by Sulphide Corporation Pty. Limited at their Cockle Creek zinc-lead smelter were found to be caused by premature softening of sinter in the upper shaft of the furnace. This soft- ening was shown to be a consequence of raw materials and operating policies which led to unusually high levels of both lead and silica in a sinter of low basicity. A programme of softening tests and micro-examination of a range of sinters established that premature softening occurred when lead and silica increased to the point where a lead-calcium silicate with a low lime content became the major continuous phase in the sinter. This information was used to define a range of compositions which kept the softening temperature acceptably high for furnace operations.

Jan 1, 1978

Pongkor Gold Mines is one of seven units of production owned by PT Aneka Tambang (State owned mining company). The mine is located in the western part of Java Island, Indonesia. It is in the Bogor District and approximately 110 kilometres to the south of capital Jakarta. It is located in very steep hilly terrain intersected by many river valleys and the mine site is approximately 500 metres above mean sea level (see Figures 1 and 2 - Mine location map and picture)

Jan 1, 1997